Uniden U-Bell Quick Start Manual
U
Wireless Video Doorbell
-
Bell
Quick Start Guide
1080p
Full HD
DB1
Two-way
Motion
Audio
U-Bell includes Lifetime Warranty
Activated
180°
Field of View
Night
Vision
Regulatory Information
FCC Information
Please note that changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provided with antenna installation instructions
and consider removing the no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation
2
Symbol Conventions
The symbols that may be found in this document are defined as follows:
NOTE
Provides additional information to emphasize or
supplement important points of the main text.
Indicates a potentially hazardous situation, which if not
WARNING
avoided, could result in equipment damage, data loss,
performance degradation, or unexpected results.
WAR NING
• The working temperature of the device is from -30° C to 50° C .
• All electronic operation should be strictly in compliance with the electrical
safety regulations, fire prevention regulations and other related regulations in
your local region.
• Please make sure that the power has been disconnected before you wire or
install the device.
• When the product is installed on a wall, the device shall be firmly fixed.
• If smoke, odors or noise rise from the device, turn o the power at once and
unplug the powercable.
• If the product does not work properly, contact the retailer you purchased it
from or Uniden customer support. Never attempt to disassemble the device
yourself. (We shall not assume any responsibility for problems caused by
unauthorized repair or maintenance.)
• Do not drop the device or subject it to physical shock, and do not expose it to
high electromagnetic radiation. Avoid the equipment installation on vibrations
surface or places subject to shock.
• Do not place the device in extreme heat (refer to the specification of the
device for the detailed operating temperature), cold, dusty or damp locations,
and do not expose it to high electromagnetic radiation.
• The device cover should be kept away from rain and moisture.
• Exposing the equipment to direct sun light, low ventilation or heat source such
as heater or radiator should be avoided or damage may occur.
• Do not aim the device at the sun or extra bright places. A blooming or smear
may occur otherwise, and aecting the endurance of sensor at the same time.
• Please keep all packaging after unpacking them for future use. In case any
failure occurs, you will need to return the device to the retailer with the original
packaging. Transportation without the original packaging may result in
damage to the device and lead to void of warranty.
• Please connect a resistor (included in the box content) to the doorbell if no
electrical chime or mechanical chime is connected.
(16 VAC to 24 VAC)
NOTE
Make sure the power voltage across the doorbell
is between 16 VAC and 24 VAC.
Resistor
WiFi Video Doorbell
3
Loading...