Ultimate Sound T-26830 Owners manual

2

Table of Contents

English

French

Spanish

German

Specifications

Table of Contents

3

4-5

6-7

8-9

10-11

12-15

Pages

T2-Series

3

Ultimate Car Audio products have been designed to deliver awesome performance and
the coolest look on the street! Learning from our past successes, our new products have
been developed with a whole new look and attitude. After all, we want you to have an
ultimate car audio system. Ultimate would like to thank you for purchasing it’s products.

• IMPP woofer cone

• Ultra linear Santoprene rubber surround

• Neodymium PEI tweeter and piezo

• Two layer high temperature KSV voice coil

• Strontium magnet structure

• Chrome stamped steel basket

• Removable speaker grill

Introduction

Be advised that exposure to loud music for a long period of time may result in permanent
hearing damage. Loud music can also distract you while driving, and prevent you from
reacting quickly to emergency situations. Ultimate will accept no liability due to misuse
of it’s products.

Caution

Ultimate’s T2 Series speakers are super cool. They look hot! They sound
awesome! But they won’t break your bank account. Now that IS cool! Using proven
engineering technologies like IMPP cones and PEI dome tweeters, these speakers will play
and look hard all day long. We invest countless hours into creating the sound that you
desire. The result is a smooth frequency response curve that will bring a smile to your ears!

Designed to drop into the factory location without any crazy mods. Removable protective
grills make it easy to maintain that stock look, whether behind your door panels, in the
dash or under the rear shelf. Or if you choose, keep them on and give your friends
something to talk about. It’s all about the attitude!

Description

Features

4

Installation Precautions

Ultimate recommends professional installation of all it’s products. Should you choose to install this
product yourself, please read this manual carefully and refer to the instructions detailed below.
Failure to do so may result in poor product performance, premature or immediate malfunction,
and potential damage to your vehicle or it’s contents.

Installation

T2-Series

• Always wear protective eyewear when using tools.

• Check for clearance in each mounting location before drilling any holes or installing any

screws.

• In some vehicles,verify that the speaker will not interfere in any wires,control cables,fuel lines
or any other factory components.

• For door installation, check for clearance of window crank lever and make sure the speaker
magnet does not hit the window or its mechanism.

• Use a utility knife to remove the excess vinyl, carpet or particleboard before using any
electrical tools to cut out the holes.

• Do not mount speakers where they can get wet.

• Start by unpacking the speakers, and laying out the various components. At this point,discard what won’t be used for

your specific application. For example, the grills will not be used when your vehicle contains factory provisions that
conceal the speaker system.

• Depending on whether you have selected to change the front and/or rear speakers,this will determine the next steps

of your installation. Front speaker will typically be found in the doors, dashboard,or kick panel locations. Rear speakers
are normally found in either the doors, side panels, or rear parcel shelf locations.

• You want to ensure that the correct replacement size has been purchased, in order to maintain the original condition

of the vehicle. Choosing a speaker which is larger in size from the original equipment may require customization in
order for a proper installation.

• Next step in the process is removing the factory grills or panels that conceal the speakers. Be careful when removing

any panels, as the clips they use to hold them in place can be quite fragile. Proper tools are necessary to ensure damage
does not result.

• Remove the speakers and set the screws aside.In some instances, these screws are custom machined and should be

reused for your new speakers.Disconnect the wires and/or plugs from these speakers.

• Prior to installing your speakers, it is important to ensure that all obstructions are noted. Window mechanisms and

truck lid bars are typically near or behind the speaker locations.You want to make sure these functions will continue to
operate without obstruction from the speakers.This would result from larger magnet structures or deeper speaker than
what is provided by the factory.

• It is critical that you determine the polarity of each wire in order to make a proper connection to your

Ultimate

speakers. No damage will result from this, but the bass performance will suffer as result. It is best to test your
sound system before installing any grills or panels. If you find that the bass is stronger when the balance is taken to one
side, the wires have in fact been reversed.

• Complete your installation by re-installing all grills or panels,taking note of any wire harness and/or clips that were

disconnected or removed.You are now ready to enjoy the improved sound quality from these

Ultimate speakers.

5