U-Line U-BI2115B-20, U-ADA15IMS-01, U-BI2115B-00, U-BI2115S-00, U-BI2115S-01 Install Manual

®

INSTALL GUIDE

ICEMAKER SERIES

BI2115ADA15IM

SS98

WH95

Models Covered

• U-ADA15IMB-00 • U-BI2115SOD-01 • ULN-BI95WH-20 • ULN-SS1095FD-20

• U-ADA15IMS-00 • U-BI2115SOD-20 • ULN-BI98B-00 • ULN-SS1095NF-03

• U-ADA15IMS-01 • U-BI2115SOD-22 • ULN-BI98B-20 • ULN-SS1095NF-20

BI98

SS1095SP18BI95

• U-BI2115B-00 • U-BI2115W-00 • ULN-BI98WH-00 • ULN-SS98-03

• U-BI2115B-20 • U-BI2115W-20 • ULN-BI98WH-20 • ULN-SS98-20

• U-BI2115S-00 • ULN-BI95B-00 • ULN-SP18B-03 • ULN-WH95TP-03

• U-BI2115S-01 • ULN-BI95B-20 • ULN-SP18B-20 • ULN-WH95TP-20

• U-BI2115S-20 • ULN-BI95BTP-03 • ULN-SS1095FC-03

• U-BI3226S-22 • ULN-BI95BTP-20 • ULN-SS1095FC-20

• U-BI2115SOD-00 • ULN-BI95WH-00 • ULN-SS1095FD-03

The American Built-In Undercounter Leader Since 1962

ULINE.COM

1 Table of Contents

Safety Precautions

Safety Alert Definitions.........................................................................................................................................1

General Precautions..............................................................................................................................................1

Inspect & Plan

Product Registration .............................................................................................................................................2

Models Covered.....................................................................................................................................................2

Tools / Material Required ....................................................................................................................................2

Exterior Cleaning ...................................................................................................................................................2

Prepare Site

Cut-Out Dimensions.............................................................................................................................................3

ADA15IM Models ....................................................................................................................................... 3

BI-95(B)(WH) Models................................................................................................................................ 3

BI-98 / SS-98 Models .................................................................................................................................. 3

BI-2115 Models............................................................................................................................................ 3

SP-18 Models................................................................................................................................................ 3

SS-1095NF Models...................................................................................................................................... 4

SS-1095FC Models...................................................................................................................................... 4

SS1095FD...................................................................................................................................................... 4

BCM95 Models ............................................................................................................................................ 4

WH95TP Models ........................................................................................................................................ 4

BI95BTP......................................................................................................................................................... 4

Product Dimensions

ADA15IM BI95 95TP BCM95 BI98 BI2115......................................................................................................5

SS1095 SP18 BCM95 WH95 SS1095NF................................................................................................ 6

Door Swing Dimensions.......................................................................................................................................7

Other Site Requirements

Power Supply ..........................................................................................................................................................7

Water Supply ..........................................................................................................................................................7

Environmental Requirements..............................................................................................................................7

Door Reversal

BI95 & BI98..............................................................................................................................................................8

WH95TP, BI95BTP, BCM95 & SP18 .................................................................................................................9

SS1095 ....................................................................................................................................................................10

Door Panel Installation

Door Panel Preparation......................................................................................................................................12

Panel Dimensions.................................................................................................................................................12

Door Panel Installation (98, SP18, & ADA15)...............................................................................................12

Power Supply

Electrical Specifications.......................................................................................................................................13

Adjust Door

Checking Door Alignment.................................................................................................................................13

Adjusting Door Alignment.................................................................................................................................13

Plumbing

Water Supply Connection .................................................................................................................................14

Install

Leveling Information............................................................................................................................................15

Installation..............................................................................................................................................................15

Grille Installation ..................................................................................................................................................15

Installation Troubleshooting..............................................................................................................................16

IMPORTANTIMPORTANT

DANGER

WARN ING

CAUTION

2 Safety Precautions

DANGER

WARN ING

WARN ING

CAUTION

IMPORTANTIMPORTANT

• PLEASE READ all instructions before installing,
operating, or servicing the appliance.

General Precautions

Use this appliance for its intended purpose only. Follow these
general precautions with those listed throughout this guide:

• Proper installation procedures must be followed when
completing an installation or relocation of a unit.
Consult the installation guide before any installation
begins. U-Line contact information appears on the rear
cover of this guide.

• This unit requires connection to a dedicated 15 Amp
grounded (three-prong), polarized receptacle, installed
by a qualified electrician, compliant with applicable
electrical codes.

Safety Alert Definitions

Throughout this guide are safety items labeled with a Danger,
Warning or Caution based on the risk type:

Danger means that failure to follow this safety statement will
result in severe personal injury or death.

Warning means that failure to follow this safety
statement could result in serious personal injury,
property or equipment damage.

RISK OF CHILD ENTRAPMENT. Before you throw away your
old refrigerator or freezer, take off the doors and leave shelves
in place so children may not easily climb inside.

SHOCK HAZARD - Electrical Grounding Required.

• Never attempt to repair or perform maintenance on
the unit until the electricity has been disconnected.

• Never remove the round grounding prong from the
plug and never use a two-prong grounding adapter.

• Altering, cutting of power cord, removal of power
cord, removal of power plug, or direct wiring can
cause serious injury, fire and or loss of property and
or life, and will void the warranty.

• Never use an extension cord to connect power to the
unit.

• Always keep your working area dry.

Install provided Anti-Tip kit. Serious personal
injury could occur.

• Use care when moving and handling the unit. Use gloves
to prevent personal injury from sharp edges.

• If your model requires defrosting, DO NOT use an ice
pick or other sharp instrument to help speed up
defrosting. These instruments can puncture the inner
lining or damage the cooling unit. DO NOT use any type
of heater to defrost. Using a heater to speed up
defrosting can cause personal injury and damage to the
inner lining.

Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.

• Do not lift unit by door handle.

• Never install or operate the unit behind closed doors.
Be sure front grille is free of obstruction. Obstructing
free airflow can cause the unit to malfunction and will
void the warranty.

• Failure to clean the condenser every six months can
cause the unit to malfunction. This could void the
warranty.

• Allow unit temperature to stabilize for 24 hours before
use.

• Do not Block any internal Fans

Use only genuine U-Line replacement parts. Imitation
parts can damage the unit, affect its operation or
performance and may void the warranty.

Precautions 1

3 Inspect & Plan

WARN ING

Product Registration

You have received a carton containing your ice maker unit with a
package inside containing a Use and Care Guide, a Product
Registration Card, and a water line kit. Please complete and
mail the Product Registration Card or register online at 
www.U-LineService.com. Once your unit is installed, keep the Use
and Care Guide and this Installation Guide in a safe place for future
reference.

Models Covered

This installation guide covers the following models

U-ADA15IMB-00 ULN-BI98B-00

U-ADA15IMS-00 ULN-BI95WH-00

U-ADA15IMS-01 ULN-SP18B-03

U-BI2115B-00 ULN-SP18WH-03

U-BI2115S-00 ULN-SS1095FC-03

U-BI2115S-01 ULN-SS1095FD-03

U-BI2115SOD-00 ULN-SS1095NF-03

U-BI2115SOD-01 ULN-SS95-03

U-BI2115W-00 ULN-SS98-03

ULN-BI95B-00 ULN-WH95TP-03

ULN-BI95WH-00

Please carefully follow the directions that apply to your unit and
your intended design.

Tools / Material Required

• Screwdrivers — slotted and Phillips head

• 1/4-inch thick door panel material and cutting tools (If installing

a 1/4" Panel)

• 1/4" Nut Driver

• 5/16" Nut Driver

• Side Cutter

• Copper tubing cutter

• 12" Level

• 9/16" Open end wrench

• 7/16" Open end wrench

• Pliers

• Copper tubing

A complete water hook up kit is also available for purchase from
your dealer. Order U-Line Part No. WATERHOOKUP.

Exterior Cleaning

Black and White Models:

• Black and White surfaces may be cleaned with a mild detergent

and warm water solution. Do not use solvent-based or abrasive
cleaners. Use a soft sponge and rinse with clean water. Wipe
with a soft, clean towel to prevent water spotting.

Stainless Models:

• Stainless door panels, handles and frames can discolor when

exposed to chlorine gas, pool chemicals, salt water or cleaners
with bleach.

• Keep your Stainless unit looking new by cleaning with a good

quality all-in-one stainless steel cleaner/polish on a monthly
basis. For best results use Claire Stainless Steel Polish and
Cleaner, which can be purchased from U-Line Corporation
(Part numbers 173348). Frequent cleaning will remove surface
contamination that could lead to rust. Some installations may
require cleaning on a weekly basis.

• Do not clean with steel wool or abrasive pads.

• Do not use cleaners that are not specifically intended

for stainless steel on stainless surfaces (this includes
glass, tile and counter cleaners).

• If any surface discolors or rust appears, clean it quickly with

Bon-Ami or Barkeepers Friend Cleanser and a non-abrasive
cloth. Always clean in the direction of the grain. Always finish
this process with Claire Stainless Steel Polish and Cleaner or
comparable product to prevent further problems.

2 U-Line Inspect & Plan

Rust that is allowed to linger can penetrate into the
surface of the stainless steel and complete removal of
the rust may not be possible.

4 Prepare Site

IMPORTANTIMPORTANT

23-3/4”

Minimum

15-1/4"

32"

to

33"

See Electrical
Specifications

for Power Supply

8"

8"

Typical

Counter

Height

34-1/4"

to

35-1/8"

Cut-Out

Height

25-1/16"

Filler Panel (Not Provided by U-Line) –

May Be Added Above or Below Unit

to Enclose for a Built-In Look

14-3/16"

18-1/2" Minimum

See Electrical
Specifications

for Power Supply

8"

Typical

Counter

Height

34-1/4"

to

35-1/8"

Cut-Out

Height

27-3/8"

Filler Panel (Not Provided by U-Line) –

May Be Added Above or Below Unit

to Enclose for a Built-In Look

15-3/16"

21-1/2"

Minimum

See Electrical
Specifications

for Power Supply

See Electrical
Specifications

for Power Supply

34-1/8"

to

35-1/8"

15-1/4"

8"

23-7/8"

Minimum

Cut-Out

Height

18-7/8"

26" Minimum

See Electrical
Specifications

for Power Supply

8" Height

From Floor

Filler Panel (Not Provided by U-Line) –

Needed to Attach Mounting Flange on Unit

k

14-1/4"

Cut-Out Width

3/4"

Minimum Flange

Mounting Area

3/4"

Minimum Flange

Mounting Area

3/4”

Minimum Flange

Mounting Area

Your U-Line product has been designed for either free-standing or
built-in installation. When built-in, your unit does not require
additional air space for top, sides or rear. However, the front grille
must NOT be obstructed and clearance is required for an
electrical and water connection in the rear.

Units can NOT be installed behind a closed cabinet door.

Cut-Out Dimensions

ADA15IM Models

BI-98 / SS-98 Models

BI-2115 Models

BI-95(B)(WH)

Models

SP-18 Models

Toe Kic

Prepare Site 3

SS-1095NF Models

8"

Typical

Counter

Height

34-1/4"

to

35-1/8"

Cut-Out

Height

25-1/16"

Filler Panel (Not Provided by U-Line) –

May Be Added Above or Below Unit

to Enclose for a Built-In Look

14-1/4"

18-1/2" Minimum

See Electrical
Specifications

for Power Supply

Cut-Out

Height

25-1/8”

Filler Panel (Not Provided by U-Line) –

Needed to Attach Mounting Flange on Unit

18-1/2” Minimum

See Electrical
Specifications

for Power Supply

8" Height

From Floor

14-1/4”

Cut Out Width

3/4”

Minimum Flange

Mounting Area

3/4”

Minimum Flange

Mounting Area

Cut-Out

Height

25-1/8”

Filler Panel (Not Provided by U-Line) –

Needed to Attach Mounting Flange on Unit

18-1/2”” Minimum

See Electrical
Specifications

for Power Supply

8" Height

From Floor

14-1/4”

Cut Out Width

3/4”

Minimum Flange

Mounting Area

3/4”

Minimum Flange

Mounting Area

Cut-Out

Height

26-1/16"

Filler Panel (Not Provided by U-Line) –

Needed to Attach Mounting Flange on Unit

18-1/2” Minimum

See Electrical
Specifications

for Power Supply

8" Height

From Floor

14-3/4”

Cut Out Width

3/4”

Minimum Flange

Mounting Area

3/4”

Minimum Flange

Mounting Area

Cut-Out

Height

25-1/8"

18-1/2" Minimum

See Electrical
Specifications

for Power Supply

8" Height

From Floor

Filler Panel (Not Provided by U-Line) –

Needed to Attach Mounting Flange on Unit

Toe Kick

14-1/4"

Cut-Out Width

3/4"

Minimum Flange

Mounting Area

3/4"

Minimum Flange

Mounting Area

3/4”

Minimum Flange

Mounting Area

Cut-Out

Height

25-1/16"

18-1/2" Minimum

See Electrical
Specifications

for Power Supply

8" Height

From Floor

Filler Panel (Not Provided by U-Line) –

Needed to Attach Mounting Flange on Unit

Toe Kick

14-1/4"

Cut-Out Width

3/4"

Minimum Flange

Mounting Area

3/4"

Minimum Flange

Mounting Area

3/4”

Minimum Flange

Mounting Area

SS-1095FC Models

BCM95 Models

WH95TP Models

SS1095FD

4 U-Line Prepare Site

BI95BTP