Ubiquiti Networks ES-10X User Manual

Page 1
8-Port Gigabit Switch with PoE Passthrough and 2 SFP Ports
Model: ES-10X
Page 2
Introduction
Thank you for purchasing the Ubiquiti Networks® EdgeSwitch® 10X. This Quick Start Guide is designed to guide you through installation and also includes warranty terms.
Package Contents
Ground Screw Power Adapter
Screws (Qty. 2)
(24V, 1A)
Anchors (Qty. 2)
Cable Clip
Wall Mount
Installation Requirements
• For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.
• For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.
We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial‑grade, shielded Ethernet cable from Ubiquiti Networks. For more details, visit: www.ubnt.com/toughcable
WARNING: To reduce the risk of fire or electric shock,
do not expose the EdgeSwitch to rain or moisture.
Note: Although the cabling can be located outdoors,
the EdgeSwitch itself should be housed inside a protective enclosure.
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the professional installer’s responsibility to follow local country regulations, including operation within legal frequency channels, output power, indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.
Page 3
Hardware Overview
Front Panel Ports
RJ45 Ports 1-8
Interface Description
RJ45 1‑8 RJ45 por ts support 10/100/1000 Ethernet
PoE In
(Port 1)
PoE Out
(Port 8)
SFP 9‑10 Hot‑swappable SFP ports support 1 Gbps
connections. Supports 24V Passive PoE input.
Supports 24V Passive PoE passthrough.
connections.
Front Panel Button
SFP Ports 9-10
Reset
Button Description
Reset
To reset to factory defaults:
1. Disconnect power from the EdgeSwitch.
2. Reconnect power while holding the Reset button. The port LEDs will light up in sequential order (this takes approximately five seconds).
3. When the port 1 LED flashes again, release the Reset button.
Page 4
Front Panel LEDs
System
System LED
State Status
Flashing White Bootup in Progress
White
Blue
Flashing Blue Used to Locate a Device in UNMS
You can use the EdgeSwitch Configuration Interface or UNMS to manage your device. UNMS lets you configure, monitor,
upgrade, and back up your devices using a singleapplication.
Get started at www.unms.com
Ready for Use
Not Connected to Ubiquiti® Network Management System (UNMS™)
Ready for Use
Connected to UNMS
Page 5
RJ45 LEDs
Speed/Link/Activity
LED
Speed/ Link/ Activity
SFP LEDs
LED
Link/ Activity
State Status
Off No Link
Amber Link Established at 10/100 Mbps
Amber Flashing
Link Activity at 10/100 Mbps
Green Link Established at 1000 Mbps
Green Flashing
Link Activity at 1000 Mbps
Link/Activity
State Status
Off No Link
Green Link Established at 1 Gbps
Green Flashing
Link Activity at 1 Gbps
Page 6
Back Panel
Power
24VDC
Grounding Point
Interface Description
Power Connect the included Power Adapter to the
Grounding
Power port. Ground bonding point for an optional
Point
ground wire.
Side Panel
Bracket Mounting
Holes
Ventilation
Holes
Page 7
Hardware Installation
The EdgeSwitch can be placed on a horizontal surface, mounted on a wall, or mounted in a rack (brackets not included). Follow the Wall Mounting instructions to mount the EdgeSwitch using the included screws and anchors.
WARNING: FAILURE TO PROVIDE PROPER VENTILATION
MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF CLEARANCE NEXT TO THE VENTILATION HOLES FOR ADEQUATE AIRFLOW.
WARNING: The EdgeSwitch ES‑10X must not be stacked.
Do not place it on top of another switch. Do not place anything on top of the ES‑10X.
Wall Mounting
To mount the EdgeSwitch on a wall, you will need a drill, a
6mm drill bit, and a Phillips screwdriver.
1. Use a 6 mm drill bit to drill two holes 148 mm apart.
2. Insert the Wall Mount Anchors into the holes. Use a Phillips screwdriver to secure a Wall Mount Screw to each anchor. Leave a clearance of approximately 3 mm between each screw head and its anchor.
148 mm
3 mm
Note: You can also mount the EdgeSwitch in a
vertical orientation.
Page 8
3. Position the EdgeSwitch with the Ethernet ports facing down. Place the wall‑mount slots of the EdgeSwitch over the screw heads on the wall. Then slide the EdgeSwitch down to lock it into place.
24VDC
Grounding the EdgeSwitch (Recommended)
The EdgeSwitch is grounded through the Power Cord; however, you can add optional ESD grounding for enhanced ESD protection.
1. Attach the Ground Screw to secure a ground wire (not included) to the Grounding Point.
2. Optional: To secure the Power Adapter cord, insert it into the Cable Clip and secure the Cable Clip using the GroundScrew.
3. Secure the other end of the ground wire to a grounding block.
Page 9
Connecting Power
The EdgeSwitch can be powered by the included Power Adapter or 24V Passive PoE.
Note: Only one power source can be used at any one
time. With both power sources connected, the input with the highest voltage will be used; the other power source defaults to backup.
Using the Power Adapter
1. Connect the Power Adapter to the Power port.
2. Connect the other end of the Power Adapter to a power outlet.
Using PoE Input
1. Connect an Ethernet cable from your 24V PoE source to the PoE In port on the EdgeSwitch.
1
2 5
3
PoE IN
4
876
9
PoE OUT
10
Page 10
Connecting Ethernet
1. Connect an Ethernet cable from your DHCP server or LAN system to any available port 1‑7 on the EdgeSwitch.
1
2 5
3
PoE IN
4
876
9
PoE OUT
10
2. Connect your 24V Passive PoE device to the PoE Out port on the EdgeSwitch.
WARNING: Before enabling PoE passthrough in the
EdgeSwitch Configuration Interface, ensure that the connected PoE device supports 24V Passive PoE.
1
2 5
3
PoE IN
4
876
9
PoE OUT
10
3. Connect your computer or host system and other devices to the other ports on the EdgeSwitch.
Page 11
Using SFP Ports
To use an SFP port:
1. Remove the protective plug covering the SFP port.
2. Plug a compatible fiber module into the SFP port.
1
2 5
3
PoE IN
4
876
9
PoE OUT
10
1000Mbps SM/SC 20KM DDM Tx1550nm/Rx1310nm
3. Connect the fiber optic cable to the fiber module. Then connect the other end of the cable to another fiber device.
1
2 5
3
PoE IN
4
876
9
PoE OUT
10
For information about compatible fiber SFP modules, visit:
community.ubnt.com/edgemax
Page 12
Accessing the Configuration Interface
The EdgeSwitch is set to DHCP by default, so it will try to automatically obtain an IP address. If that fails, then it will use the default fallback IP address, 192.168.1.20. Proceed to the appropriate section, DHCP or Fallback IP Address:
DHCP
Use one of the following methods:
• Set up the DHCP server to provide a specific IP address to
the EdgeSwitch based on its MAC address (on the label).
• Let the EdgeSwitch obtain an IP address and then check the
DHCP server to see which IP address was assigned.
To log in, follow these steps:
1. Launch your web browser. Type the appropriate IP address in the address field. Press enter (PC) or return (Mac).
2. The login screen will appear. Enter ubnt in the Username and Password fields. Click Sign In. (When you sign in, you agree to accept the Ubiquiti License Agreement.)
The EdgeSwitch Configuration Interface will appear. Customize additional settings as needed. For 24V Passive PoE configuration, refer to the Configuring PoE Settings section. For more information, refer to the EdgeSwitch documentation, which is available at www.ubnt.com/download/edgemax
You can also manage your device using UNMS, which lets you configure, monitor, upgrade, and back up your devices using a
singleapplication. Get started at www.unms.com
Page 13
Fallback IP Address
1. Ensure that your computer (or other host system) is connected to the EdgeSwitch.
2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.
3. Launch your web browser. Type the appropriate IP address in the address field (192.168.1.20 is the default fallback IP address). Press enter (PC) or return (Mac).
https://192.168.1.20
4. The login screen will appear. Enter ubnt in the Username and Password fields. Click Sign In. (When you sign in, you agree to accept the Ubiquiti License Agreement.)
5. The EdgeSwitch Configuration Interface will appear. Click the System tab.
Page 14
6. Change the IP Address to a unique IP address or keep the default, DHCP. Click Apply.
Note: If you change the IP settings, then the session
will be cut off, and you will need to reconnect to the EdgeSwitch using the new IP address.
The EdgeSwitch Configuration Interface will appear. Customize additional settings as needed. For 24V Passive PoE configuration, refer to the Configuring PoE Settings section. For more information, refer to the EdgeSwitch documentation, which is available at www.ubnt.com/download/edgemax
You can also manage your device using UNMS, which lets you configure, monitor, upgrade, and back up your devices using a
singleapplication. Get started at www.unms.com
Page 15
Configuring PoE Settings
The PoE setting for port 8 is set to Off by default.
WARNING: Before activating PoE, ensure that the
connected device supports passive PoE and the supplied voltage.
On the Dashboard tab, click the PoE setting of port 8. Then select 24V.
Page 16
Specifications
Dimensions 207 x 31.1 x 90 mm (8.15 x 1.22 x 3.54")
Weight 500 g (1.10 lb)
Interfaces
Networking
Management
Power Method 24VDC, 1A or
Power Supply 24VDC, 1A Power Adapter (Included) or
Supported Voltage Range 9 ‑30VDC
Max. Power Consumption (Excluding PoE Output)
LEDs
System RJ45 Data Ports SFP Data Ports
ESD/EMP Protection Air: ± 24 kV, Contact: ± 24 kV
Shock and Vibration ETSI300‑019‑1.4 Standard
Operating Temperature ‑10 to 50° C (14 to 122° F)
Operating Humidity 5 to 95% Noncondensing
Certications CE, FCC, IC
PoE Interface 24VDC Passive PoE (Pins +4, 5; ‑7, 8)
Max. Passive PoE Wattage per Port
24V Passive PoE Voltage Range 24V
ES‑10X
(8) 10/100/1000 Mbps RJ45 Ports
PoE (Port 8)
(2) 1 Gbps SFP Ports
Ethernet In‑Band
24V Passive PoE
24V Passive PoE
Status
Link/Speed/Activity
Link/Activity
8W
15W
Page 17
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Failure to provide proper ventilation may
cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow.
WARNING: To reduce the risk of fire or electric shock, do
not expose this product to rain or moisture.
WARNING: Do not use this product in location that can
be submerged by water.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet.
a. Do not substitute the power cord with one that is not the provided
approved type. Never use an adapter plug to connect to a 2‑wire outlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of the
safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there
are questions about the installation prior to connecting the equipment.
d. Protective earthing is provided by Listed AC adapter. Building
installation shall provide appropriate short‑circuit backup protection.
e. Protective bonding must be installed in accordance with local
national wiring rules and regulations.
Page 18
Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term.
Warranty Conditions
The above warranty does not apply if the Product: (I) has been modified and/or altered, or an addition made thereto,
except by Ubiquiti Networks, or Ubiquiti Networks’ authorized
representatives, or as approved by Ubiquiti Networks in writing; (II) has been painted, rebranded or physically modified in any way; (III) has been damaged due to errors or defects in cabling; (IV) has been subjected to misuse, abuse, negligence, abnormal physical,
electromagnetic or electrical stress, including lightning strikes, or
accident; (V) has been damaged or impaired as a result of using third party
firmware; (VI) has no original Ubiquiti MAC label, or is missing any other original
Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of
the RMA. In addition, the above warranty shall apply only if: the product has been
properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed.
Returns
No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS’ facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal. Information on the RMA process and obtaining an RMA number can be found at: www.ubnt.com/support/warranty
Page 19
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND NON‑INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error‑free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyer’s selection of products (including the Products) for buyer’s application and/or failure of products (including the Products) to meet government or regulatory requirements.
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Page 20
Note
Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
ISED Canada
CAN ICES‑3(A)/NMB‑3(A)
This Class A digital apparatus complies with Canadian CAN ICES‑003.
CAN ICES‑3(A)/NMB‑3(A)
Cet appareil numérique de la classe A est conforme à la norme NMB‑003 du Canada.
Page 21
Australia and New Zealand
Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
CE Marking
CE marking on this product represents the product is in compliance with all directives that are applicable to it.
RoHS/WEEE Compliance Statement
English
European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
Deutsch
Die Europäische Richtlinie 2012/19/EU verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.
Page 22
Español
La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.
Français
La directive européenne 2012/19/UE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.
Italiano
La direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.
Page 23
Declaration of Conformity
български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че това устройство
ES-10X е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес:
Hrvatski [Croatian] UBIQUITI NETWORKS ovim putem izjavljuje da je ovaj uređaj ES-10X
sukladan osnovnim zahtjevima i ostalim bitnim odredbama Direktiva 2014/30/EU, 2014/35/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi:
www.ubnt.com/compliance
Čeština [Czech] UBIQUITI NETWORKS tímto prohlašuje, že toto ES-10X zařízení, je ve
shodě se základními požadavky a dalšími příslušnými ustanoveními směrnic 2014/30/EU, 2014/35/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese:
www.ubnt.com/compliance
Dansk [Danish] Hermed, UBIQUITI NETWORKS, erklærer at denne ES-10X enhed,
er i overensstemmelse med de væsentlige krav og øvrige relevante krav i direktiver 2014/30/EU, 2014/35/EU. EU-overensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse:
www.ubnt.com/compliance
Nederlands [Dutch] Hierbij verklaart UBIQUITI NET WORKS, dat deze ES-10X apparaat, in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijnen 2014/30/EU, 2014/35/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres:
English
Hereby, UBIQUITI NETWORKS, declares that this ES-10X device, is in compliance with the essential requirements and other relevant provisions of Directives The full text of the EU declaration of conformity is available at the following internet address:
www.ubnt.com/compliance
Eesti keel [Estonian] Käesolevaga UBIQUITI NETWORKS kinnitab, et antud ES-10X seade,
on vastavus olulistele nõuetele ja teistele asjakohastele sätetele direktiivide 2014/30/EL, 2014/35/EL. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil:
www.ubnt.com/compliance
Suomi [Finnish] Täten UBIQUITI NETWORKS vakuuttaa, että tämä ES-10X laite, on yhdenmukainen
olennaisten vaatimusten ja muiden sitä koskevien direktiivien 2014/30/EU, 2014/35/EU. EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa:
Français [French] Par la présente UBIQUITI NETWORKS déclare que l’appareil ES-10X, est
conforme aux exigences essentielles et aux autres dispositions pertinentes des directives 2014/30/UE, 2014/35/UE. Le texte complet de la déclaration UE de conformité est disponible à l’adresse internet suivante:
Deutsch [German] Hiermit erklärt UBIQUITI NET WORKS, dass sich dieses ES-10X
Gerät, in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinien 2014/30/EU, 2014/35/EU befindet. Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar:
www.ubnt.com/compliance
Ελληνικά [Greek] Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η συσκευή ES-10X,
είναι σε συμμόρφωση με τις βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις των οδηγιών 2014/30/EE, 2014/35/EE. Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο:
Magyar [Hungarian] Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a ES-10X készülék
megfelel az alapvető követelményeknek és más vonatkozó 2014/30/EU, 2014/35/EU irányelvek rendelkezéseit. Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen:
Íslenska [Icelandic] Hér, UBIQUITI NETWORKS, því yfir að þetta ES-10X tæki er í samræmi við
grunnkröfur og önnur viðeigandi ákvæði tilskipana 2014/30/ESB, 2014/35/ESB. Fullur texti ESB samræmisyfirlýsing er að finna á eftirfarandi netfangi:
www.ubnt.com/compliance
www.ubnt.com/compliance
www.ubnt.com/compliance
www.ubnt.com/compliance
www.ubnt.com/compliance
2014/30/EU, 2014/35/EU
www.ubnt.com/compliance
www.ubnt.com/compliance
.
Page 24
Italiano [Italian] Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo ES-10X,
è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet:
Latviešu valoda [Latvian] Ar šo, UBIQUITI NETWORKS, deklarē, ka ES-10X ierīce, ir saskaņā ar
būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvās 2014/30/ES, 2014/35/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē:
Lietuvių kalba [Lithuanian] UBIQUITI NETWORKS dek laruoja, kad šis ES-10X įrenginys atitinka
esminius reikalavimus ir kitas 2014/30/ES, 2014/35/ES Direktyvų nuostatas. Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu:
Malti [Maltese]
mar-rekwiżiti essenzjali u dispożizzjonijiet rilevanti oħrajn ta ‘Direttivi 2014/30/UE, 2014/35/UE. Id-dikjarazzjoni tal-konformità tista’ tiġi kkonsultata minn www.ubnt.com/compliance
Norsk [Norwegian]
med de grunnleggende kravene og andre relevante bestemmelser i direktivene 2014/30/EU, 2014/35/EU. Den fulle teksten til EU-samsvarserklæringen er tilgjengelig på følgende internettadresse: www.ubnt.com/compliance
Polski [Polish] Niniejszym, Ubiquiti Networks, oświadcza, że urządzenie ES-10X, jest zgodny
z zasadniczymi wymaganiami oraz pozostałymi stosownymi postanowieniami Dyrektyw 2014/30/UE, 2014/35/UE adresem internetowym:
Português [Portuguese] UBIQUITI NETWORKS declara que este dispositivo ES-10X, está
conforme com os requisitos essenciais e outras disposições das Directivas 2014/35/UE endereço de Internet:
Română [Romanian] Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitiv ES-10X este
în conformitate cu cerințele esențiale și alte prevederi relevante ale Directivelor 2014/35/UE internet:
Slovenčina [Slovak]
je v súlade so základnými požiadavkami a ďalšími relevantnými ustanoveniami smernice 2014/30/EÚ, 2014/35/EÚ
www.ubnt.com/compliance
Slovenščina [Slovenian]
skladu z obveznimi zahtevami in drugimi ustreznimi določbami direktiv 2014/30/EU in 2014/35/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu:
www.ubnt.com/compliance
Español [Spanish] Por medio de la presente UBIQUITI NETWORKS declara que este dispositivo
ES-10X, cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de las Directivas conformidad está disponible en la dirección Internet siguiente:
Svenska [Swedish] Härmed UBIQUITI NETWORKS, intygar att denna ES-10X enhet är i
överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiven överensstämmelse finns på följande webbadress:
www.ubnt.com/compliance
www.ubnt.com/compliance
Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz ES-10X huwa konformi
Herved UBIQUITI NETWORKS, erklærer at denne ES-10X enheten, er i samsvar
. Pełny tekst deklaracji zgodności UE jest dostępny pod następującym
www.ubnt.com/compliance
. O texto integral da declaração de conformidade está disponível no seguinte
www.ubnt.com/compliance
. Textul integral al declarației UE de conformitate este disponibil la următoarea adresă
www.ubnt.com/compliance
Týmto UBIQUITI NETWORKS, prehlasuje, že toto ES-10X zariadenie,
. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese:
Družba UBIQUITI NETWORKS izjavlja, da je naprava ES-10X v
2014/30/UE, 2014/35/UE
2014/30/EU, 2014/35/EU
www.ubnt.com/compliance
2014/30/UE,
2014/30/UE,
. El texto completo de la declaración UE de
www.ubnt.com/compliance
. Den fullständiga texten till EU-försäkran om
www.ubnt.com/compliance
Online Resources
Support help.ubnt.com Community community.ubnt.com Downloads downloads.ubnt.com
Page 25
www.ubnt.com
Ubiquiti Networks, Inc.
685 Third Avenue, 27th Floor
New York, NY 10017
USA
©2018 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, UbiquitiNetworks,
the Ubiquiti U logo, the Ubiquiti beam logo, EdgeMAX, EdgeOS, EdgeSwitch, TOUGHCable, and UNMS are trademarks or registered trademarks of
UbiquitiNetworks,Inc. in the United States and in other countries. All other
trademarks are the property of their respective owners. JL052318
Loading...