Page 1
Datasheet
Optical Data Transport
for Outdoor PoE Devices
Model: F-POE-G2
Reliable Long-Distance Gigabit PoE Runs
Enhanced ESD Protection and EMI Reduction
Dependable 24V/50V Passive PoE Transport
Page 2
Fiber + Power Solution
Datasheet
for Outdoor PoE Devices
Overcome PoE limitations with the next-generation
FiberPoE™, model F-POE-G2. The FiberPoE Gen 2 is a
low-cost solution for outdoor deployments that require
long-distance runs to reach the PoE device. Deployments
with the FiberPoE Gen 2 provide signicant EMI and ESD
protection over typical PoE installations. The FiberPoE
Gen 2 also features a durable, weatherproof form factor
and enhanced surge protection.
Separate Data and Power Transport
PoE is ideal for indoor or short-run installations.
However, for outdoor, long-distance installations, PoE
becomes vulnerable to EMI and is limited to 100 meters
with correlated power loss. With the FiberPoE Gen 2,
data and power are transported on separate cables to
greatly improve data integrity and enable much longer
cableruns.
The FiberPoE Gen 2 provides Gigabit bi-directional data
transport between twisted-pair Ethernet cable and ber
optic cable, and injects DC power to the Ethernet cable
for passive PoE. Use one FiberPoE Gen 2 device as an
Fiber-to-Ethernet Converter, or a pair of FiberPoE Gen 2
devices to create a Fiber Bridge.
To PoE
Device
DC
Injection
Fiber
Optic
Enhanced Surge Protection
Featuring a built-in high-current Gas Discharge Tube
(GDT) for the DC terminal block and PoE port, the
FiberPoE Gen 2 delivers enhanced surge protection. The
added GDT support effectively protects against lightning
and other power surges.
Fiber Optic Data Transport
Using ber optic cable for data transport signicantly
reduces electrostatic discharge (ESD) failures and
electromagnetic interference (EMI). Data integrity is also
sustained in runs beyond 100 meters, the limit of Ethernet
over twisted-pair cable.
The FiberPoE Gen 2 supports a 1G SFP module and 24V or
50V power from a DC power cable or PoE cable.
2
Page 3
Integrated Fiber Cable Strain Relief
Switch/Router
Switch/Router
An integrated strain relief system was thoughtfully designed
to t inside the FiberPoE Gen 2 cover for added protection
and a cleaner installation.
Fiber Cable
Strain Relief Reel
Application Examples
The following are typical use cases for the FiberPoE Gen 2.
Data Options
Datasheet
Cable Strain
Relief Tabs
1. Fiber-to-Ethernet Converter One FiberPoE Gen 2 at the
top of the tower is used to convert ber to Ethernet at
the radio. At the base of the tower, the ber optic cable
connects directly to a ber switch or router.
PoE Device
Ethernet Cable
FiberPoE
Gen 2
Fiber
Optic Cable
2. Fiber Bridge Two FiberPoE Gen 2 devices, one at
the base and one at the top of the tower, are used to
provide a ber optic data link for protection from EMI
events that can cause equipment damage or signal
integrity issues.
PoE Device
Ethernet Cable
FiberPoE
Gen 2
Fiber
Optic Cable
Fiber
FiberPoE
Gen 2
Ethernet Cable
Ethernet
3
Page 4
Terminal
Block
DC In
(RJ45)
PoE
(RJ45)
Datasheet
Power Input Port Input Power Output Power
Terminal Block
(DC Power)
DC In
(Power Only)
PoE
(Power and Data)
2-wire DC, 24V PoE port, 2-pair (4,5+; 7, 8-), 24V
2-wire DC, 50V PoE port, 4-pair, 50V
2-pair (4, 5+; 7, 8-), 24V
4-pair, 24V
4-pair, 50
2-pair (4,5+; 7, 8-), 24V Terminal Block, 24V
4-pair, 24V Terminal Block, 24V
4-pair, 50V Terminal Block, 50V
Terminal Block, 24V
PoE port, 24V, 2-pair (4, 5+; 7, 8-)
Terminal Block, 24V
PoE port, 24V, 4-pair
Terminal Block, 50V
PoE port, 50V, 4-pair
4
Page 5
Terminal Block Input
T
Near the
DC In (RJ45) Input
T
Near the
PoE (RJ45) Input
Bottom
Power Input/Output Examples
op of Tower
PoE Device
Datasheet
op of Tower
PoE Device
24VDC Input 24V (2-Pair)
24V (2-Pair)
DC Input
Power and Data
to PoE Device
24V (2-Pair)
Power and Data
to PoE Device
50VDC Input 50V (4-Pair)
24V (4-Pair)
DC Input
Power and Data
to PoE Device
24V (4-Pair)
Power and Data
to PoE Device
of Tower
50V (4-Pair)
DC Input
24/50V
DC Output
50V (4-Pair)
Power and Data
to PoE Device
24/50V Power and Data
from PoE Adapter or PoE Switch
24/50V
DC Output
24/50V
DC Input
24/50V
Power and Data
to PoE Device
5
Page 6
Specications
F-POE-G2
Datasheet
Dimensions 196.4 x 93.5 x 32.4 mm
( 7.73 x 3.68 x 1.28")
Weight 288 g
(10.2 oz)
Enclosure White Polycarbonate
Interface Connections (1) 1 Gbps SFP Port
(1) DC Terminal Block
(1) DC RJ45 Port DC Injection
(1) 1000 Mbps Ethernet PoE Port
1
Typical Power Consumption 1.5W
Power Method DC Terminal Block, 2-Wire, 24VDC or 50VDC
DC In RJ45 Port, 2-Pair (4,5+; 7,8-) (24VDC Input), or
4-Pair (24VDC or 50VDC Input) Passthrough
PoE RJ45 Port, 2-Pair (4,5+; 7,8-) (24VDC Input), or
4-Pair (24VDC or 50VDC Input) PoE Passthrough
PoE Output PoE RJ45 Port, 2-Pair (4,5+; 7,8-) (24VDC), or
4-Pair (24VDC or 50VDC) PoE
DC Output Terminal Block, 2-Wire (24VDC or 50VDC)
Input DC Voltage
16 to 57V
Surge Protection Built-In High-Current Gas Discharge Tube
for DC Terminal Block and PoE Port
LED White: Power On
Blue: Connected
Blue (Flashing): Activity
Operating Temperature -40 to 60° C2
(-40 to 140° F)
Operating Humidity 10 to 95% Noncondensing
ESD/EMP Protection ± 24kV Contact / Air for Ethernet
Certications CE, FCC, IC
¹ 10/100 Mbps Ethernet not supported.
² May be further restricted by the operating temperature
range of the SFP module being used.
NB071718
6
Specications are subject to change. Ubiquiti products are sold with a limited warranty described at: www.ubnt.com/support/warranty
©2018 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, and FiberPoE are trademarks
or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their
respectiveowners.
www.ubnt.com
Loading...