Tyco Safety Sensormatic BIM1000 User Manual

Download

Page 1

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-03 REV 3E INSTALLATION GUIDE

1 of 32 *8200-1088-03*

Business Intelligence Module (BIM1000)

Installation Guide

BIM1000

Page 2

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-03 REV 3E INSTALLATION GUIDE

2 of 32 *8200-1088-03*

Contents

About this guide ..................................................................................................................................... 4

Additional documentation .................................................................................................................... 4

Technical Support ............................................................................................................................... 4

About the product ....................................................................................................................................... 5

Features .............................................................................................................................................. 5

Compatibility ........................................................................................................................................ 5

Section I: Installation sequence overview ................................................................................................ 7

Section II: Before you begin ....................................................................................................................... 8

Installation prerequisites ....................................................................................................................... 8

Training ................................................................................................................................................ 8

Part numbers .......................................................................................................................................... 8

Survey and planning requirements ...................................................................................................... 9

Survey requirements ........................................................................................................................... 9

Network Topology Map requirements ................................................................................................. 9

Application and firmware requirements ............................................................................................... 9

TrueVUE requirements ...................................................................................................................... 10

Laptop requirements ......................................................................................................................... 10

Component installation requirements ............................................................................................... 10

Electrical power requirements ........................................................................................................... 10

Wiring requirements .......................................................................................................................... 10

Tools required ................................................................................................................................... 11

Safety ..................................................................................................................................................... 11

Section III: Installing the Business Intelligence Module (BIM1000) ..................................................... 12

Overview of steps ................................................................................................................................. 12

Step 1: Locating the Business Intelligence Module ......................................................................... 12

Step 2: Mounting the Business Intelligence Module ........................................................................ 13

Mounting the Business Intelligence Module to a hollow cavity wall .................................................. 13

Mounting the Business Intelligence Module to the ceiling ................................................................ 14

Mounting the Business Intelligence Module to a surface-mounted electrical box ............................ 17

Step 3: Connecting and securing the Business Intelligence Module ............................................. 18

Section IV: Connecting the Business Intelligence Module (BIM1000) ................................................. 20

Overview of connection steps ............................................................................................................ 20

Equipment required ............................................................................................................................. 20

Step 1: Connecting the Business Intelligence Module .................................................................... 21

Ethernet cable set-up ........................................................................................................................ 21

USB set-up ........................................................................................................................................ 23

Step 2: Optional: Installing a cellular modem ................................................................................... 25

Step 3: Commissioning the Business Intelligence Module ............................................................. 26

Step 4: Powering on the Business Intelligence Module ................................................................... 28

Step 5: Verifying the Business Intelligence Module ......................................................................... 29

Page 3

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-03 REV 3E INSTALLATION GUIDE

3 of 32 *8200-1088-03*

Specifications ............................................................................................................................................ 30

Declarations ............................................................................................................................................... 31

Other declarations ................................................................................................................................ 32

Page 4

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-03 REV 3E INSTALLATION GUIDE

4 of 32 *8200-1088-03*

About this guide

This installation guide explains how to install the Business Intelligence Module (BIM1000) with the Business Intelligence Accessory (BIX1000), to synchronize all Sensormatic-connected devices.

Additional documentation

The following is a list of additional documents related to this installation:

 Business Intelligence Accessory (BIX1000) Installation Guide, 8200-1088-15.  Business Intelligence Module (BIM1000) and Business Intelligence Accessory (BIX1000) Setup Guide,

8200-1088-01.

 Ultra Post® IV AMS-1012 Business Intelligence Accessory (BIX1000) Cable Kit Installation Guide,

8200-1088-05.

 Ultra Post® VI AMS-1014 Business Intelligence Accessory (BIX1000) Cable Kit Installation Guide,

8200-1088-06.

 Ultra 1.8 Meter ABS Pedestal Business Intelligence Accessory (BIX1000) Cable Kit Installation Guide,

8200-1088-07.

 AMB9010-IPS and AMB-1200 Label Deactivator Controller Business Intelligence Accessory (BIX1000)

Cable Kit Installation Guide, 8200-1088-08.

 AMS-9050 Controller Business Intelligence Accessory (BIX1000) Cable Kit Installation Guide,

8200-1088-09.

 AMS-9040 Controller Business Intelligence Accessory (BIX1000) Cable Kit Installation Guide,

8200-1088-10.

 AMS-9060 Controller and AMS-1170-2C/4C Controller Business Intelligence Accessory (BIX1000) Cable

Kit Installation Guide, 8200-1088-11.

 ZBSMPROE ScanMax® Pro Label Deactivator Controller Business Intelligence Accessory (BIX1000) Cable

Kit Installation Guide, 8200-1088-12.

 IDKM-10XX/AMK-10XX SuperTag® Detacher Business Intelligence Accessory (BIX1000) Cable Kit

Installation Guide, 8200-1088-13.

 AMB-2011/AMB-1101/ZBAMB9010 EAS Label Deactivator Business Intelligence Accessory (BIX1000)

Cable Kit Installation Guide, 8200-1088-16.

 Business Intelligence Accessory (BIX1000) Extension Cable Kit Installation Guide, 8200-1088-14.

Technical Support

For product bulletins, and the most recent updates to this guide, visit https://sensormaticsecurelogin.com

Page 5

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-03 REV 3E INSTALLATION GUIDE

5 of 32 *8200-1088-03*

About the product

The Business Intelligence Module (BIM1000) is a wireless access point that connects to the Business Intelligence Accessory (BIX1000).

Using IEEE 802.15.4 wireless protocol, the Business Intelligence Accessory (BIX1000) connects to the Business Intelligence Module (BIM1000) to synchronize all in-store Sensormatic-connected devices, to collect data and to provide a health status for all connected devices. For an example, see Figure 1 and Figure 2 on page 6.

The data collected includes alarms, events, and people-counting statistics. It also collects alarm response times to help eliminate false deactivation and detection alarms at store exits.

Customers can use a desktop browser to log into a TrueVUE reporting platform, or a Shrink Management as a Service (SMaaS) platform, to access daily data reports from all the connected devices.

The customer can also use the Device Mobile App (BIZ1000), which is compatible with iOS and Android smart devices, or they can use the Business Intelligence Module (BIM1000) Manager Interface, to monitor store-wide EAS device health, counts, and events in real-time.

Features

The Business Intelligence Module (BIM1000) has the following features:

 An embedded web configurator.  A wired EAS Network (RS-485).  A wireless EAS Network, 802.15.4  A wireless 802.11.B/G/N (Client and Soft AP).  It can support 32 devices.  It has MicroSD flash storage.  It has Micro USB Type B access.  It has Bluetooth radio for wireless setup.

Compatibility

The Business Intelligence Module (BIM1000) is compatible with the following devices:

 The Ultra Post® IV AMS-1012 Pedestal.  The Ultra Post® VI AMS-1014 Pedestal.  The Ultra 1.8 Meter ABS Pedestal.  The AMS-9060 Controller.  The AMS-9050 Controller.  The AMS-9040 Controller.  The AMS-1080 Controller.  The AMS-1170-2C/4C Controller.  The ZBAMB9010 EAS Label Deactivator Controller.  The AMB9010-IPS EAS Label Deactivator Controller.  The ZBSMPROE ScanMax® Pro Label Deactivator Controller.  The AMB-1200C EAS Label Deactivator Controller.  The AMK-1000 and the AMK-1010 SuperTag® Detacher.  The IDKM-1000 and the IDKM-1010 SuperTag® Detacher.  The AMB-2011 Value Pad II Countertop EAS Label Deactivator.  The AMB-1101 VersaPass II Countertop EAS Label Deactivator.

Commented [ARB1]: Comment from Marc: It has mmd so same format but a chip not a card. Clarify with

Marc.

Page 6

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-03 REV 3E INSTALLATION GUIDE

6 of 32 *8200-1088-03*

Figure 1. Overview of the Business Intelligence Module (BIM1000) solution

Internet

LP Manager

Gateway

Business Intelligence Accessory (BIX1000)

Network switch

Business Intelligence Module (BIM1000)

Wireless Access Point (802.11 Wi-Fi)

Figure 2. Business Intelligence Module (BIM1000), 0304-0170-01

Speaker

RGB visual display

Micro USB port

Locking tab

Radio antenna (802.15.4)

Wi-Fi antenna

802.11 Wi-Fi

802.15.4 Wi-

BCD

Page 7

PRELIMINARY

BUSINESS INTELLIGENCE ACCESSORY (BIX1000) 8200-1088-03, REV 2C INSTALLATION GUIDE

7 of 32 *8200-1088-15*

Section I: Installation sequence overview

Figure 3 gives an overview of the complete installation sequence you must follow when you install a BIM1000 and a BIX1000. You must install the

BIM1000 before you install the BIX1000.

Figure 3. BIM1000 and BIX1000 complete installation sequence

Important: This installation guide only describes the following steps in the complete BIM1000 and BIX1000 installation sequence:

 Before you begin: Planning and prerequisites  Step 1: Install the BIM  Step 5: Validate the BIM1000 configuration  Step 6: Validate BIM1000 remote connectivity

Before you begin:

Planning and prerequisites

Step 3:

Install the BIX1000

cable kits

Step 4:

Install and locate

the BIX1000

Step 5:

Validate BIM1000

configuration

Step 6:

Validate BIM1000

remote connectivity

Install the

BIM1000. Turn on the BIM1000, and program the

PAN ID and the

Channel

Install the

relevant

BIX1000 cable

kit, and

configure the

EAS devices

Install and

locate the

BIX1000

Validate the

complete

BIM1000 and

BIX1000

configuration

Validate the

remote

connectivity

and data

transportation

of the BIM1000

Commission the BIX1000

Step 2:

Commission the

BIX1000

Step 1:

Install the

BIM1000

Confirm all the

prerequisites in

Section II are

complete before

beginning

installation

Commented [BA[G-C2]: Feedback from Marc, survey and planning should be a pre-step. Store layout, which BIX to which BIM, Network and RS-485 topology.

Page 8

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

8 of 32 *8200-1088-15*

Section II: Before you begin

Before you install a Business Intelligence Module (BIM1000), ensure that you adhere to the criteria outlined in the following sections.

Installation prerequisites

To install a Business Intelligence Module (BIM1000), you must have the following criteria in place before you proceed:

 Do you have the Network Topology Map requirements, or IP Request Form?  Do you have the location of each BIM1000 identified? You can obtain this information from the Network

Typology Map.

 Is there power and data, for example Ethernet, Wi-Fi, or 4G gateways, where you plan on locating the

BIM1000?

 Do you have the applicable network ports open for functionality and device management support?  Have you completed the necessary training required to install the Business Intelligence Module (BIM1000)?

Training

WARNING: Do not attempt to install a Business Intelligence Module (BIM1000) unless you have completed the

Wireless Device Manager (BIM/BIX) Training Curriculum. To install a Business Intelligence Module (BIM1000), you must complete the following technical training

modules:

 BIM and BIX Installation Technical Training.  BIM Configuration Technical Training.

 Optional: SMaaS Overview Sales Training.

Part numbers

Table 1 lists the part numbers you require to install a Business Intelligence Module (BIM1000).

Table 1. Business Intelligence Module (BIM1000) part numbers

Part number

Description

Quantity

0352-0766-01

BIM1000 Installation Kit

1400-0033-01

T-bar clip

1400-0205-01

T-bar clip, 1/4-20, 5/8” L, 15/16” W

2838-0015-01

Flange nut, 1/4-20, 7/16 WAF

2880-0070-01

Toggle bolt, 1/4-20 x 6.00

2880-0094-01

Anchor, self-drill, with screws, #8 x 1-1/4

0304-0170-01

BIM1000 module

0404-1247-01

BIM1000 mounting bracket

3411-0027-01

Antenna

0352-0473-01

Ceiling mount, IVS

0404-1244-01

BIX mounting back cover kit

3135-1525-01

BIM Power Supply

0352-0897-01

BIM PWR connector-cable

6003-0313-01

Micro USB B to USB-B cable, 1.8m

Commented [ARB3]: These part numbers are not included in the BOM Marc sent me. Are these going to be included in the BOM or do they need to be ordered separately?

Could you please provide the part number for the power connector cable, I cannot locate it on Windchill?

Page 9

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

9 of 32 *8200-1088-15*

Survey and planning requirements

This section outlines the site survey and planning requirements, and the systems requirements that are critical to the correct installation of a BIM1000.

Survey requirements

You must access the following criteria before you proceed with the installation of a BIM1000:

 The layout and design of the installation site.  The location of each BIM1000 module. You can obtain this information from the Network Typology Map.  Identify each BIX1000 you need to program to each BIM1000 module.

Network Topology Map requirements

You require the following information for each device you place on the network when you install a Business Intelligence Module (BIM1000) to work with a Business Intelligence Accessory (BIX1000). This information is in the Network Topology Map that the project manager or the coordinator for the account supplies, or in the IP Request form document that the customer’s IT department supplies.

 The location of each BIM1000 module.  The switch location, name and port number.  Any Wi-Fi restrictions, if setting up the BIM1000 to operate in Access Point (AP) mode.  The Wi-Fi channel.

Note: The Wi-Fi channel is dependent on the region of installation.

 The Wi-Fi access point location and the Service Set Identifier (SSID).  A static or a dynamic IP address.  The Subnet Mask.  The Gateway  The NTP Server.  The Ethernet MAC address.  The Wi-Fi Subnet Mask.  The Wi-Fi Default Gateway.  The SIP Server address.

Application and firmware requirements

In order to support the installation of a Business Intelligence Module (BIM1000), you must download the latest firmware bundle, 1.00 or later, and the BIM Web Launch Tool from https://sensormaticsecurelogin.com/.

To download the BIM Web Launch Tool, complete the following steps:

1. Open a web browser and launch https://sensormaticsecurelogin.com/.

2. Enter your valid logon information and click Login.

3. From the Tech Support menu, click EAS.

4. Click Software Download.

5. Click BIM Web Launch Tool Vx.xx

6. To download the software bundle, click the link, and save the file to a local folder on your laptop.

7. Log out of www.sensormaticsecurelogin.com/.

8. On your laptop, rename the file you saved to an .exe file. Click the executable file, and click Run.

Commented [BA[G-C4]: Question for Marc Blanchenay: Does the installer need to do this or will it be included in the

Network Typology Map?

Page 10

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

10 of 32 *8200-1088-15*

9. Follow the setup wizard instructions to save the software on your laptop.

Note: Files save to the following location: C:\Program Files\Sensormatic\BIM Software Bundle x.x. (Program Files (x86) for 64 bit machines).

TrueVUE requirements

To support TrueVUE reports for a Business Intelligence Module (BIM1000) installation, you require the following:

 TrueVUE ,version 7.5 or later.  The SIP URL as stated in the Network Topology Map.  If authentication is necessary, you need your valid service credentials.  The store name, the store number, and the division number.  The heartbeat interval.  Ensure the appropriate port is open, typically port 8080 or 8081.

Laptop requirements

You require the following items for your laptop:  Internet Explorer version 11, or Mozilla Firefox version 56, or Google Chrome version 64, browser installed.

Note: Ensure JavaScript are blockers on the web browser.

 A USB port.  An Ethernet adapter.

Component installation requirements

This section outlines components installation requirements to install a Business Intelligence Module (BIM1000).

Electrical power requirements

Confirm the following electrical power requirements are in place to install a Business Intelligence Module (BIM1000):

 The AC power cord could be carrying 120Vac or 240Vac. The AC source must be a 2-wire type with

ground. It also must be a 24-hour, unswitched outlet with less than 0.5Vac between neutral and ground. Note: The BIM1000 takes its Sync signal from this AC power source.

 The BIM1000 can operate from generator supplied AC power if it meets the AC power requirements.

Important: You must select Generator Mode when configuring the BIM1000 for use in multiple generator environments.

Wiring requirements

Confirm the following wiring requirements are in place for each piece of hardware before you install a Business Intelligence Module (BIM1000):

 RS-485 cabling, including the termination of cabling, the pinouts, and a diagram with RS485-High,

RS485-Low, and Sync connections outlined.

 All Ethernet patch cables must be CAT5e, CAT6, or CAT6e.

Commented [ARB5]: Included as per conversion with John Clark. 7.5 is scheduled for release in April.

Commented [ARB6]: Removed the wireless adapter and the Bluetooth adapter from this list. Wi-Fi and Bluetooth are disabled by default so moving these sections to the Setup Guide.

Page 11

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

11 of 32 *8200-1088-15*

Tools required

Confirm that you have the following tools before you install a Business Intelligence Module (BIM1000):

 A #2 Philips head screwdriver.  A cable tester.  A Digital Volt Meter.  A micro USB cable, 6003-0313-01, or an Ethernet patch cable.  A drill, and assorted drill-bits.  A drywall saw.

Safety

You must adhere to the following safety instructions when you install a Business Intelligence Module (BIM1000):

WARNING: Risk of electric shock

Disconnect all power sources before servicing.

 Do not install the Business Intelligence Module (BIM1000) in a plenum or other environmental air-handling

space.

 You must use plenum-rated cables, unless the cables are in raceways.  Installation of the BIM1000 must comply with the latest national electrical codes, national fire code, and all

applicable local codes and ordinances. National or local wiring codes may differ between regions. Adherence to these codes supersedes instructions in this document.

 You must observe and respect all the safety instructions in this installation guide, and or the operation of the

Business Intelligence Module (BIM1000).

 You must mount the Business Intelligence Module (BIM1000) only as instructed in this installation guide.

Mounting the Business Intelligence Module (BIM1000) any other way can affect its operation.

 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications

to this equipment. Such modifications can void the user’s authority to operate the equipment.

 You must install the antennas for this transmitter with a separation distance of at least 20 centimetres (8

inches) from all persons, and must not be collocated or operating in conjunction with any other antenna or transmitter.

Commented [ARB7]: Reply from Bill Owsley: We have not yet received the FCC certificate and expect it by

months end. Because the application has the 2 antennas in it, I would guess the certificate might not have that statement. TBD.

Page 12

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

12 of 32 *8200-1088-15*

Section III: Installing the Business Intelligence

Module (BIM1000)

This section outlines how to install a Business Intelligence Module (BIM1000). Important: You must install the Business Intelligence Module (BIM1000) before you install the Business

Intelligence Transceiver (BIX1000). Note: You can power on and set-up the Business Intelligence Module (BIM1000) before you install it. To do

this, proceed to Step 4: Powering on the Business Intelligence Module on page 28.

Overview of steps

This section gives an overview of the steps involved in installing a Business Intelligence Module (BIM1000):

 Step 1: Locating the Business Intelligence Module (BIM1000).  Step 2: Mounting the Business Intelligence Module (BIM1000).  Step 3: Connecting and securing the Business Intelligence Module (BIM1000).

Step 1: Locating the Business Intelligence Module

To locate the Business Intelligence Module (BIM1000) correctly, you must adhere to the following guidelines when you locate the Business Intelligence Module (BIM1000).

 Locate the BIM1000 a minimum of 2 feet or 24 inches from the Business Intelligence Transceiver

(BIX1000). For more information, refer to the Business Intelligence Accessory (BIX1000) Installation Guide,

8200-1088-15.

 Table 2 lists the expected maximum line of sight range from BIM1000 to BIM1000 modules, and from

BIM1000 to BIX1000 modules. The maximum line of sight ranges are based on environments free of obstructions and interference, the range can significantly degrade from the specified maximums.

Table 2. Expected maximum line of sight ranges between modules

Modules

Region

Expected maximum line of sight range

BIM1000 to BIX1000

76.2 meters (250 feet)

BIM1000 to BIX1000

106.7 meters (350 feet)

BIM1000 to BIX1000EA

106.7 meters (350 feet)

BIM1000 to BIM1000

182.9 meters (600 feet)

BIM1000 to BIM1000

370 meters (1,217 feet)

 You must install the antennas for this transmitter with a separation distance of at least 20 centimetres

(8 inches) from all persons, and must not be collocated or operating in conjunction with any other antenna or transmitter.

Commented [BA[G-C8]: For the moment starting with this value. Manny will get back to me once tests are performed over the coming weeks. (05/02/18)

Commented [ARB9]: TBD.

Page 13

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

13 of 32 *8200-1088-15*

Step 2: Mounting the Business Intelligence Module

You can mount the Business Intelligence Module (BIM1000) in one of the following ways:

 To a hollow cavity wall.  To a ceiling.  To a surface-mounted electrical box.

Mounting the Business Intelligence Module to a hollow cavity wall

To mount the Business Intelligence Module (BIM1000) to wall with a hollow cavity, you require the following equipment:

 A Ceiling Mount IVS Kit, 0352-0473-01.  A BIM Mounting Plate, 0404-1247-01, supplied with the Business Intelligence Module (BIM1000).  A #2 Phillips screwdriver.  A 2-inch (5 centimeters) bell saw, or hole saw.  A drill, with assorted drill bits.  A drywall saw.

To mount a Business Intelligence Module (BIM1000) to a hollow cavity wall, complete the following steps:

1. Locate the BIM Mounting Bracket, 0404-1247-01, and orientate it with the arrows pointing up to the ceiling, as shown in Figure 4.

 Important: You must locate the Business Intelligence Module (BIM1000) a minimum of 2 feet (24 inches)

from the Business Intelligence Accessory (BIX1000).

2. Use the BIM Mounting Bracket, 0404-1247-01, as a template and with a pencil, mark the mounting holes, and the Power, the Ethernet, and the RS485 cable entry holes. See Figure 4.

Figure 4. Front view of the BIM Mounting Bracket, 0404-1247-01

Mounting holes

Arrow up indicators

Power cable opening

Ethernet cable opening

RS485 cable opening

BCD

Page 14

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

14 of 32 *8200-1088-15*

3. Use a hand drill and a 2-inch (5 centimeters) drill-bit to drill the mounting holes on the wall.

4. Use a bell saw, or a hand saw, to cut out the Power, the Ethernet, and the RS485 cable holes.

5. From the Ceiling Mount IVS Kit, 0352-0473-01, locate two drywall anchors, 2880-0094-01, and insert into the mounting holes in the wall.

6. To prepare the cabling, complete the following steps: a. Locate the RS-485 cable and feed it through the RS485 cable opening on the BIM Mounting Bracket,

0404-1247-01.

b. Secure the RS485 cable into the strain relief notch. See Figure 5.

Figure 5. BIM Mounting Bracket cable strain relief feature

c. Feed the Ethernet cable through the Ethernet cable opening on the BIM Mounting Bracket,

0404-1247-01. d. Secure the Ethernet cable into the strain relief notch. See Figure 5. e. Locate the three-pin connector cable from the XXXXX Kit and feed it through the Power cable opening

on the BIM Mounting Bracket, 0404-1247-01.

7. Secure the three-pin connector from the power cable into the strain relief notch. See Figure 5.

8. Correctly orientate the BIM Mounting Bracket in place, with the up arrows pointing to the ceiling.

9. From the Ceiling Mount IVS Kit, 0352-0473-01, locate two drywall anchor screws, 2880-0094-01, and use a #2 Phillips screwdriver to secure the BIM Mounting Bracket, 0404-1247-01, to the wall.

Mounting the Business Intelligence Module to the ceiling

To mount the Business Intelligence Module (BIM1000) to the ceiling, you require the following equipment:

 A BIM1000 Install Kit, 0352-0766-01.  A BIM1000 Mounting Bracket, 0404-1247-01, supplied with the Business Intelligence Module (BIM1000).  A drill with assorted drill bits.  Plywood or a strut channel.

You can mount the Business Intelligence Module (BIM1000) to a hard ceiling, a T-bar of a ceiling grid support, or a suspended ceiling panel using the BIM Mounting Bracket, 0404-1247-01.

Commented [WM[G-C10]: Is this the correct drill-bit size for the mounting holes?

Commented [WM[G-C11]: Are these the correct anchors from the kit? There’s two types.

Commented [WM[G-C12]: Where does the installer get the three-pin connector cable?

Commented [WM[G-C13]: Are these the correct anchors from the kit? There’s two types.

Page 15

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

15 of 32 *8200-1088-15*

Mounting the BIM1000 Mounting Bracket to a hard ceiling

To mount the Business Intelligence Module (BIM1000) to a hard ceiling complete the following steps:

1. Locate the BIM1000 Mounting Bracket, 0404-1247-01 and the BIM1000 Installation Kit, 0352-0766-01.

2. If possible, mount the BIM Mounting Bracket into a known structural member using appropriate hardware. Alternately, use the supplied toggle bolt, 2880-0070-01, to anchor the BIM1000 Mounting Bracket.

3. Use the BIM Mounting Bracket, 0404-1247-01, as a template and with a pencil, mark the mounting holes, and the Power cable entry hole.

a. If required, mark the entry locations for the RS485 or the Ethernet patch cables.

4. Use a drill with a 1/2 inch (12.5 millimeter) drill-bit, and drill the mounting hole in the ceiling.

5. Use a drill with a 1/2 inch (12.5 millimeter) drill-bit, and drill a hole for the power cable. If required, also drill a hole or holes for the RS485 or the Ethernet Patch cables.

6. From the BIM1000 Installation Kit, 0352-0766-01, locate the 6-inch toggle bolt, 2880-0070-01.

7. Adjust the toggle bolt to ensure it can expand once you place it through the ceiling, and ensure a minimum of a 1/2 inch (12.5 millimeters) of the toggle bolt remains exposed below the ceiling.

8. Thread the BIM1000 Mounting Bracket, 0404-1247-01, onto the toggle bolt, 2880-0070-01, and insert it through the ceiling.

9. Pulling down slightly on the bracket assembly, spin the BIM1000 Mounting Bracket to tighten it. Note: If you have access to the area above the ceiling, you can tighten the toggle bolt, 2880-0070-01, from

this location.

10. Place an additional screw on the BIM1000 Mounting Bracket, 0404-1247-01, to prevent the bracket from spinning or loosening when mounted. Alternately, place the flange nut, 2838-0015-01, from the BIM1000 Installation Kit, 0352-0766-01, above the toggle bolt to secure the bracket in place.

11. Complete the following steps to route the cables through the BIM1000 Mounting Bracket, 0404-1247-01: a. If required, locate the RS-485 cable, feed it through the RS485 cable opening on the BIM Mounting

Bracket, 0404-1247-01, and then secure the RS485 cable in the provided strain relief notch. For the location of the strain relief notch on the BIM1000, see Figure 5.

b. Locate the Ethernet cable and feed it through the Ethernet cable opening on the BIM Mounting Bracket,

0404-1247-01, and then secure the Ethernet cable in the provided strain relief notch.

c. Locate the power cable, feed the three-pin connector end of the cable through the Power cable opening

on the BIM Mounting Bracket, 0404-1247-01, and then secure the cable in the provided strain relief notch.

Mounting the BIM1000 Mounting Bracket to a T-bar of a suspended ceiling support

To attach the BIM Mounting Bracket, 0404-1247-01, to a T-bar of a suspended ceiling support, complete the following steps:

1. Use a hand drill with a xx drill-bit, and drill a hole in the center of the plywood.

2. From the BIM1000 Installation Kit, 0352-0766-01, locate the 6-inch toggle bolt, 2880-0070-01.

3. Insert the toggle bolt, 2880-0070-01, through the plywood, and tighten the two flanged nuts, 2838-0015-01, to secure it to the BIM Mounting Bracket, 0404-1247-01.

4. Sit the plywood across the grid support in the ceiling.

5. From the BIM1000 Installation Kit, 0352-0766-01, locate the two T-bar clips, 1400-0033-01, and clip onto the ceiling grid support to secure in place.

6. Complete the following steps to route the cables through the BIM1000 Mounting Bracket, 0404-1247-01:

Commented [BA[G-C14]: Should this step sit here or do I need to move it? Or is this a note?

Commented [BA[G-C15]: What size drill bit?

Page 16

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

16 of 32 *8200-1088-15*

a. If required, locate the RS-485 cable, feed it through the RS485 cable opening on the BIM Mounting

Bracket, 0404-1247-01, and then secure the RS485 cable in the provided strain relief notch. For the location of the strain relief notch on the BIM1000, see Figure 5.

b. Locate the Ethernet cable and feed it through the Ethernet cable opening on the BIM Mounting Bracket,

0404-1247-01, and then secure the Ethernet cable in the provided strain relief notch.

c. Locate the power cable, feed the three-pin connector end of the cable through the Power cable opening

on the BIM Mounting Bracket, 0404-1247-01, and then secure the cable in the provided strain relief notch.

Mounting the BIM1000 Mounting Bracket to a suspended ceiling panel

To attach the BIM Mounting Bracket, 0404-1247-01, to a suspended ceiling panel, complete the following steps:

1. Use a hand drill with a xx drill-bit, and drill a hole in the center of the plywood.

2. From the BIM1000 Installation Kit, 0352-0766-01, locate the 6-inch toggle bolt, 2880-0070-01.

3. Insert the toggle bolt, 2880-0070-01, through the plywood, and tighten the two flanged nuts, 2838-0015-01, to secure it to the BIM Mounting Bracket, 0404-1247-01.

4. Sit the plywood across the grid support in the ceiling.

5. From the BIM1000 Installation Kit, 0352-0766-01, locate the two T-bar clips, 1400-0033-01, and clip onto the ceiling grid support to secure in place.

6. Complete the following steps to route the cables through the BIM1000 Mounting Bracket, 0404-1247-01: a. If required, locate the RS-485 cable, feed it through the RS485 cable opening on the BIM Mounting

Bracket, 0404-1247-01, and then secure the RS485 cable in the provided strain relief notch. For the location of the strain relief notch on the BIM1000, see Figure 5.

b. Locate the Ethernet cable and feed it through the Ethernet cable opening on the BIM Mounting Bracket,

0404-1247-01, and then secure the Ethernet cable in the provided strain relief notch.

c. Locate the power cable, feed the three-pin connector end of the cable through the Power cable opening

on the BIM Mounting Bracket, 0404-1247-01, and then secure the cable in the provided strain relief notch.

Commented [BA[G-C16]: What size drill bit?

Page 17

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

17 of 32 *8200-1088-15*

Mounting the Business Intelligence Module to a surface-mounted electrical box

To mount the Business Intelligence Module (BIM1000) using a surface-mounted electrical box, you require the following equipment:

 A BIM1000 Installation Kit, 0352-0766-01.  A BIM Mounting Plate, 0404-1247-01, supplied with the Business Intelligence Module (BIM1000).  Electrical boxes: For North America, a contractor can supply quad-type electrical boxes or you can source

them locally. For all other geographies, refer to the mounting pattern in Figure 6 to determine the supported locally available electrical boxes.

Figure 6. Mounting hole dimensions on BIM1000 mounting bracket, back view

To mount the Business Intelligence Module (BIM1000) using an electrical box, complete the following steps:

1. Locate the Mounting Bracket, 0404-1247-01, and orientate it with the arrows pointing up to the ceiling. See Figure 4.

2. If the electrical box is not mounted, mount the electrical box using appropriate hardware.

3. Remove one or more knockouts on the electrical box.

4. Add strain relief to the knockouts where necessary to prevent the cables from chafing, and then secure the cable entry at the electrical box.

5. Complete the following steps to route the cables through the BIM1000 Mounting Bracket, 0404-1247-01: a. If required, locate the RS-485 cable, feed it through the RS485 cable opening on the BIM Mounting

Bracket, 0404-1247-01, and then secure the RS485 cable in the provided strain relief notch. For the location of the strain relief notch on the BIM1000, see Figure 5.

b. Locate the Ethernet cable and feed it through the Ethernet cable opening on the BIM Mounting Bracket,

0404-1247-01, and then secure the Ethernet cable in the provided strain relief notch.

c. Locate the power cable, feed the three-pin connector end of the cable through the Power cable opening

on the BIM Mounting Bracket, 0404-1247-01, and then secure the cable in the provided strain relief notch.

Note: Installing the Business Intelligence Module (BIM1000) to a 4x4 electrical box provides additional depth for cable connectors.

6. Orientate the Mounting Bracket, 0404-1247-01, with the arrows pointing up, over the electrical box.

5. Use two screws supplied with the electrical box, or two screws compatible with the electrical box, and secure the BIM Mounting Bracket, 0404-1247-01, to the electrical box.

8.5 cm

8.4 cm

8.3 cm

6 cm

4.6 cm

Page 18

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

18 of 32 *8200-1088-15*

Step 3: Connecting and securing the Business Intelligence Module

To secure the Business Intelligence Module (BIM1000) to the Mounting Bracket, 0404-1247-01, complete the following steps:

1. Locate the Business Intelligence Module (BIM1000).

2. Insert the three-pin connector from the power cable to the Power port on the back of the Business Intelligence Module (BIM1000). See Figure 7.

Figure 7. Back view of the BIM Mounting Bracket, 0404-1247-01

Reset button

Power port

Ethernet port

RS485 port

Locking tab

Tamper switch

3. Insert the Ethernet cable to the Ethernet port on the back of the Business Intelligence Module (BIM1000). See Figure 7.

4. Insert the RS485 cable to the RS485 port on the back of the Business Intelligence Module (BIM1000). See Figure 7.

5. Align the Business Intelligence Module (BIM1000) to the BIM Mounting Bracket, 0404-1247-01. See Figure 8 on page 19.

6. Insert the Business Intelligence Module (BIM1000) to the BIM Mounting Bracket, 0404-1247-01, and rotate counter-clockwise to engage the locking tab.

CBDEF

Page 19

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

19 of 32 *8200-1088-15*

Figure 8. Securing the Business Intelligence Module (BIM1000) to the BIM Mounting Bracket,

Removing the Business Intelligence Module from the mounting bracket

To remove the Business Intelligence Module (BIM1000) from the Mounting Bracket, 0404-1247-01, complete the following steps:

1. Use a small, flat screw driver to push lightly on the tamper switch on the left-hand side of the Business Intelligence Module (BIM) to disengage the locking tab.

2. Rotate the Business Intelligence Module (BIM) counter-clockwise to release it from the Mounting Bracket, 0404-1247-01.

Page 20

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

20 of 32 *8200-1088-15*

Section IV: Connecting the Business Intelligence

Module (BIM1000)

This section outlines how to connect the Business Intelligence Module (BIM1000).

Overview of connection steps

This section gives an overview of the steps involved in connecting a Business Intelligence Module (BIM1000).

 Step 1: Connecting the Business Intelligence Module.  Step 2: Installing a cellular modem.  Step 3: Configuring the Business Intelligence Module.  Step 4: Powering on the Business Intelligence Module.  Step 5: Verifying the Business Intelligence Module.

Equipment required

To connect the Business Intelligence Module (BIM1000), you require the following equipment:

 ?  ?

Commented [WM[G-C17]: Bill to check hardware

Page 21

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

21 of 32 *8200-1088-15*

Step 1: Connecting the Business Intelligence Module

You can connect and power the Business Intelligence Module (BIM1000) in the following ways:

 An Ethernet cable set-up  A USB set-up  A Wi-Fi set-up  A Bluetooth set-up

Note: Wi-Fi and Bluetooth are disabled by default. To connect to the BIM1000 module using Wi-Fi or Bluetooth set-up, refer to the Business Intelligence Module (BIM1000) and Business Intelligence Accessory

(BIX1000) Setup Guide, 8200-1088-01.

Ethernet cable set-up

To connect a Business Intelligence Module (BIM1000) using an Ethernet cable set-up, complete the following procedure:

1. Connect the Ethernet cable to your laptop and to the Business Intelligence Module (BIM1000).

2. You can connect to the Business Intelligence Module (BIM1000) in one of the following ways:

 Use the BIM Web Launch Tool to connect to the Business Intelligence Module (BIM1000) using the

BIM Web Launch Tool, by completing the following steps:

a. On your laptop, open the BIM Web Launch Tool. b. From the Network Adapter list, select the relevant Ethernet connection type. c. In the IP Address field, enter 192.168.0.100 d. Click Launch.

Note: This launches a web browser to connect to the Business Intelligence Module (BIM1000).

Figure 9. BIM1000 Web Interface Launcher

 Use the laptop network settings to connect to the Business Intelligence Module (BIM1000) using the

laptop’s network settings, by completing the following steps:

a. Complete the following steps to navigate to the laptop’s network settings:

i. Click Start.

ii. Click Control Panel. iii. Click Network and Internet. iv. Click Network and Sharing Center.

Page 22

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

22 of 32 *8200-1088-15*

v. Ensure that the laptop’s network matches the following network settings for the

BIM1000:

 BIM default IP address: 192.168.0.100  BIM default Gateway: 192.168.0.254  BIM default Subnet mask: 255.255.255.0

b. Complete the following steps to verify that the laptop’s IP address is on the same subnet as

the Business Intelligence Module (BIM1000):

i. Click the Network icon on your desktop toolbar. ii. Click Local Area Connection.

iii. Click Properties. iv. Click Internet Protocol Version 4 (TCp/IPv4).

v. Click Properties.

vi. Click Use the following IP address.

vii. In the IP address field, enter 192.168.0.100

viii. In the Subnet mask field, enter 255.255.255.0 and click OK. c. On the laptop, launch an internet browser. d. In the internet address bar, enter the following IP address of the Business Intelligence

Module (BIM1000), 192.168.0.100 Note: When it connects, the Wireless Device Configuration webpage displays.

4. To logon to the Business Intelligence Module (BIM1000) for the first time, you require a password. To obtain a password, complete the following steps:

a. In the User Login pane, click Generate to generate a challenge string.

Note: The generated string is valid for one week only. Do not click the Generate Challenge String button more than once, if you click the button more than once, you need to obtain another string.

b. Copy the string that is generated in the Generate Challenge String field.

5. Launch an internet browser and navigate to https://sensormaticsecurelogin.com/.

6. Enter your valid logon details, and click Login.

7. Read the Terms & Conditions, and if you agree, select the check box and click Agree.

8. From the Tech Support menu, click Configurator Registration, and complete the following steps:

a. From the Product Code list, click AMS-9060 Web Configuration UI. b. In the Register Number field, enter the generated challenge string you copied in step 4b. c. Click Submit.

Note: A challenge string and service password is sent to the email you registered.

Page 23

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

23 of 32 *8200-1088-15*

USB set-up

To connect a Business Intelligence Module (BIM1000) using a micro USB cable, 6003-0313-01, complete the following steps:

1. Connect the micro USB cable, 6003-0313-01, to your laptop and to the Business Intelligence Module (BIM1000). For the location of the micro USB port on the BIM1000, see item C, in Figure 2.

2. You can connect to the Business Intelligence Module (BIM1000) in one of the following ways:

 Use the BIM Web Launch Tool to connect to the Business Intelligence Module (BIM1000) using the

BIM Web Launch Tool, by completing the following steps:

a. On your laptop, open the BIM Web Launch Tool. b. From the Network Adapter list, select the relevant Ethernet connection type. c. In the IP Address field, enter 192.168.2.100 d. Click Launch.

Note: This launches a web browser to connect to the Business Intelligence Module (BIM1000).

 Use the laptop network settings to connect to the Business Intelligence Module (BIM1000) using the

laptop’s network settings, by completing the following steps:

a. Complete the following steps to navigate to the laptop’s network settings:

i. Click Start.

ii. Click Control Panel. iii. Click Network and Internet. iv. Click Network and Sharing Center.

v. Ensure that the laptop’s network matches the following network settings for

the BIM1000:

 BIM default IP address: 192.168.2.10  BIM default Gateway: 192.168.0.254  BIM default Subnet mask: 255.255.255.0

b. Complete the following steps to verify that the laptop’s IP address is on the same subnet as

the Business Intelligence Module (BIM1000):

i. Click the Network icon on your desktop toolbar.

ii. Click Local Area Connection. iii. Click Properties. iv. Click Internet Protocol Version 4 (TCp/IPv4).

v. Click Properties. vi. Click Use the following IP address.

vii. In the IP address field, enter 192.168.2.100

Module (BIM1000), 192.168.2.100

Note: When it connects, the Wireless Device Configuration webpage displays.

Page 24

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

24 of 32 *8200-1088-15*

4. To logon to the Business Intelligence Module (BIM1000) for the first time, you require a password. To obtain a password, complete the following steps:

a. In the User Login pane, click Generate to generate a challenge string.

Note: The generated string is valid for one week only. Do not click the Generate Challenge String button more than once, if you click the button twice, you need to obtain another string.

b. Copy the string that is generated in the Generate Challenge String field.

5. Launch an internet browser and navigate to https://sensormaticsecurelogin.com/.

6. Enter your valid logon details, and click Login.

7. Read the Terms & Conditions, and if you agree, select the check box and click Agree.

8. From the Tech Support menu, click Configurator Registration, and complete the following steps:

a. From the Product Code list, click AMS-9060 Web Configuration UI. b. In the Register Number field, enter the generated challenge string you copied in step 4b. c. Click Submit.

Note: A challenge string and service password is sent to the email you registered.

Page 25

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

25 of 32 *8200-1088-15*

Step 2: Optional: Installing a cellular modem

This step is optional if you chose to install a cellular modem. To install a cellular modem, follow the instructions that come with the cellular modem.

Commented [WM[G-C18]: Check with Marc Blanchenay

Page 26

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

26 of 32 *8200-1088-15*

Step 3: Commissioning the Business Intelligence Module

This section outlines how to commission a Business Intelligence Module (BIM1000): To commission the BIM1000, complete the following steps:

1. Return to the Business Intelligence Module webpage, and use the challenge string to generate the service password, if necessary. See Step 1: Connecting the Business Intelligence Module.

2. From the BIM Configuration menu, click BIM Status. Ensure that the versions and information in the following fields are correct, and click Save.

a. Software Version – 00.07.1, or higher b. Bootloader Version – 00.00.5, or higher c. IP Address – 192.168.0.100

3. If you need to update the firmware on the BIM1000, complete the following steps: a. From the BIM Configuration menu, click Firmware Update. b. Click Browse, and select the BIM_BIX_RADIO_CFG_WEB_X_XX tar file.

Note: X_XX in the tar file indicates the latest version of the firmware. c. Click Download. d. Wait for a Transfer Completed Successfully dialog box to open, and then click OK. e. Click Update. f. If the update does not complete successfully, repeat steps a, b, c, d, and e.

Note: If you the BIM1000 does not update successfully, you may be instructed to perform a factory

reset. For further information, contact Technical Support. If you need to perform a factory reset,

complete the following steps:

i. From the BIM Configuration menu, click Radio Settings.

ii. Record the values for the Pan ID, Channel, and Power, and then click Save. iii. From the BIM Configuration menu, click BIM Status. iv. Click Factory Reset.

v. Verify that the following firmware version updated successfully:

 Software Version: 00.07.1  Bootloader version: 00.00.5  Radio version: 00.32.7  Wi-Fi version: 2.9.0.0

vi. From the BIM Configuration menu, click Radio Settings, and restore the radio settings.

4. From the BIM Configuration menu, click Network Settings, and enter static IP information, or check the DHCP option to get an assigned IP address.

5. Optional: If required, select the Enable HTTP SSL check box to enable SSL on the web server.

6. From the BIM Configuration menu, click Radio Settings and complete the following steps:

a. In the PAN ID field, enter a value in hex from 0 x 0001 through to 0 x FFFE.

Note: The Personal Area Network (PAN) ID must be unique for each BIM1000.

b. In the Channel field, enter the Channel.

Page 27

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

27 of 32 *8200-1088-15*

Note: The Channel must be unique for each BIM1000. You can set a value from 1 to 26 for IEEE

802.15.4 radio frequencies. c. Optional: Click Generate to generate a PAN ID and Channel. d. In the Tx Power field, enter the Tx power value for the country of use, as shown in Table 3.

Table 3. BIM1000 and BIX1000 TX power

Device

TX power, North America

TX power, Europe

BIM1000

197 (20dB)

57 (10dB)

BIX1000

197 (20dB)

78 (10dB)

BIX1000EA

220 (20db)

89 (10db)

e. Click Save. Note: Write down the PAN ID and Channel details to use later on when you configure the BIX1000.

Commented [BA[G-C19]: Marc mentioned that this differs from Wi-Fi, do I need to note this here and do they need to use a different value.

Commented [ARB20]: Needs to be ironed out, and John A to include a country dropdown menu. To be decided.

Commented [ARB21]: Bill Rider to confirm

Page 28

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

28 of 32 *8200-1088-15*

Step 4: Powering on the Business Intelligence Module

To power on the Business Intelligence Module (BIM1000), complete the following procedure:

1. Plug it in

2. When LEDs blinking

Power Cable Route

The power cable route goes from:



The AC outlet inside the main electrical box in which the power supply module (1) and female-to-female coupler (2) reside.



Down through existing conduit into the UltraLink® enclosure below.



Up through existing conduit and alarm module electrical box (3).



To a 4x4 electrical box (4) mounted 3.7m (12ft) from the floor (the Sync AP mounts here using two screws as shown below). A length of conduit (5) will need to be added for power to reach this box.

Notes: The 4.6m (15ft) Cat5 cable supplied is used to get power to the Sync AP. DO NOT connect this cable to the Sync AP or the female-to-female coupler inside the main electrical box at

this time. These connections will be done at the end of the setup process. If the cable does not fit through the conduit, then cut off one of its connectors close to the end of the cable,

route the cable, then reattach the connector (see page 5 for reattachment instructions).

Commented [WM[G-C22]: Bill Rider to provide

Page 29

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

29 of 32 *8200-1088-15*

Step 5: Verifying the Business Intelligence Module

To verify that the Business Intelligence Module (BIM1000) is functioning correctly, complete the following procedure:

1. Launch an internet browser.

2. In the address bar, enter 192.168.1.100 and press enter. The Business Intelligence Module (BIM) Web Interface opens.

3. From the User dropdown list, click Service.

4. In the Password field, enter the password.

5. In the BIM Status pane, verify the following: a. Verify the Number of Devices. b. Verify the Number of Devices Online.

Note: If the Business Intelligence Module is functioning correctly, the Number of Devices and the Number of Device online match.

c. In the SIP Server Status pane, verify the last connection time and success percentage.

Commented [WM[G-C23]: Is this the password that the customer set earlier?

Page 30

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

30 of 32 *8200-1088-15*

Specifications

Electrical

Power supply

Primary input .........................................................................................................................................................................

............................................................... 18VDC input, Sync and RS485 through RJ45 8 pin header with LEDs for RS485.

Environmental

Ambient temperature ....................................................... ........................................................ 0°C to 50°C (14°F to 122°F)

Relative humidity ............................................................. ............................................................ 0 to 90% non-condensing

Enclosure Rating ............................................................. ..................................................................................... UL94 V-O

Evaluated for altitudes less than 2,000 meters (6,561.68 feet)

Mechanical

Material: ........................................................................... .............................................................................................. ABS

Color: .............................................................................. ..................................................................................... Light grey

Dimensions: .................................................................... ........................................ 139.52 mm X 114.76 mm X 62.10 mm

Weight (approx.): ............................................................ ............................................................................ 419 g (0.92 lbs)

Dimensions

Figure 10. Business Intelligence Module (BIM) dimensions, front view

114.76 mm (4.5 in)

139.52 mm (5.5) in

94.50 mm (3.7 in)

62.10 mm (2.4 in)

81.50 mm (3.2 in)

138.82 mm (5.5 in)

Page 31

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

31 of 32 *8200-1088-15*

Declarations

Model: BIM1000

Regulatory information

Contains the following radios;

FCC ID: A8TBM78ABCDEFGH, Z64-CC3100MODR1 IC ID: 12246A-BM78SPPS5M2, 451I-CC3100MODR1

Radio

Frequency of operation

Type.......................................................... ............................................................................................................. BIM1000

Frequency band............................. .................................................................................................... . 2402.0 - 2480.0 MHz

............................................................................................................................................................. 2412.0 – 2462.0 MHz

Maximum power ................................... ..................................................................................................... 10 mW in the EU

........................................................................................................................................................................ 100 mW in NA

If frequency is selectable for your model, select only the country in which you are using the device. Any other selection will make the operation of this device illegal.

Approved antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada.

Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

This radio transmitter IC: 3506A-BIM1000 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Le présent émetteur radio IC: 3506A-BIM1000 a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.

Pulse/Larsen W1027

Polarization ..................................................... .......................................................................................................... Vertical

Composite gain ............................................... .......................................................................................................... 3.2 dBi

Impedance .................................................... ......................................................................................................... 50 ohms

Pulse/Larsen W1038

Polarization ..................................................... .......................................................................................................... Vertical

Composite gain ............................................... .......................................................................................................... 3.8 dBi

Impedance .................................................... ......................................................................................................... 50 ohms

L-Com model HG2403RD-RSF

Polarization ..................................................... .......................................................................................................... Vertical

Composite gain ............................................... ........................................................................................................... 3.0 dBi

Impedance .................................................... ......................................................................................................... 50 ohms

Page 32

PRELIMINARY

BUSINESS INTELLIGENCE MODULE (BIM1000) 8200-1088-15, REV 3E INSTALLATION GUIDE

32 of 32 *8200-1088-15*

FCC ID: BVCBIM1000 This device complies with part 15 of the FCC Rules. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

México NOM 121: BIM1000 La operación de este equipo está sujeta a las siguientes dos condiciones:

es posible que este equipo o dispositivo no cause interferencia perjudicial y

este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su propia operación no deseada.

INTERNATIONAL ID: BIM1000

EMC ....................................................... .................................................................................................... 47 CFR, Part 15

............................................................................................................................................................................ EN 300 328

......................................................................................................................................................................... EN 301 489-1

......................................................................................................................................................................... EN 301 489-3

....................................................................................................................................................................... EN 301 489-17

................................................................................................................................................................................ RSS 210

Safety.......................................................... .................................................................................................... UL/EN 60950-1

................................................................................................................................................................................... CSA C22.2.60950-1

EQUIPMENT MODIFICATION CAUTION: Equipment changes or modifications not expressly approved by Sensormatic Electronics, LLC, the party responsible for FCC compliance, could void the user’s authority to operate the equipment and could create a hazardous condition.

See About this guide on page 4.

Other declarations

WARRANTY DISCLAIMER: Sensormatic Electronics, LLC makes no representation or warranty with respect to the contents hereof

and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, Sensormatic Electronics, LLC reserves the right to revise this publication and make changes from time to time in the content hereof without obligation of Sensormatic Electronics, LLC to notify any person of such revision or changes.

LIMITED RIGHTS NOTICE: For units of the Department of Defense, all documentation and manuals were developed at private expense and no part of it was developed using Government Funds. The restrictions governing the use and disclosure of technical data marked with this legend are set forth in the definition of “limited rights” in paragraph (a) (15) of the clause of DFARS 252.227.7013. Unpublished - rights reserved under the Copyright Laws of the United States.

TRADEMARK NOTICE: Sensormatic is a registered trademark of Sensormatic Electronics, LLC. Other product names mentioned herein may be trademarks or registered trademarks of Sensormatic or other companies. No part of this guide may be reproduced in any form without written permission from Sensormatic Electronics, LLC.

Tyco Safety Sensormatic BIM1000 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual