Tyco ET1215L, B1ET-1215L User Manual
Touchmonitor User Guide
1215L 12¨ LCD Desktop Touchmonitor
1000 Series
User Guide
12" LCD Desktop
ET1215L Series
Revision B
P/N E378269
Copyright © 2008 Tyco Electronics. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by any means,
including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems.
Disclaimer
The information in this document is subject to change without notice. Elo T ouchSyste ms makes no
representations or warranties with respect to the contents hereof, and specifically disclaims any
implied warranties of merchantability or fitness for a particular purpose. Elo TouchSystems reserves the right to revise this publication and to make changes from time to time in the content
hereof without obligation of Elo TouchSystems to notify any person of such revisions or change s.
Trademark Acknowledgments
IntelliT ouch, SecureTouch, AccuTouch, and MonitorMouse are tra demarks of Elo TouchSystems.
Other product names mentioned herein may be trademarks or registered trademarks of their
respective companies. Elo TouchSystems claims no interest in trademarks other than its own.
iii
Table of Contents
Chapter 1 Regulatory Information 33
Introduction 7 Warranty 37
Product Description ...................................................7
Precautions ................................................................7
Chapter 2
Installation and Setup .................................... 9
Unpacking Your Touchmonitor...................................9
Product Overview ......................................................10
Main Unit ..............................................................10
Rear View ............................................................10
Touch Interface Connection .......................................11
Installing the Driver Software .....................................12
Installing the Serial Touch Driver .........................13
Installing the Serial Touch Driver for Windows
XP, Windows 2000, Me, 95/98 and NT 4.0 .....13
Installing the Serial Touch Driver for MS-DOS
and Windows 3.1..................................................14
Installing the USB Touch Driver...........................15
Installing the USB Touch Driver for Windows
XP, Windows 2000, Me, 95/98 and NT 4.0 .....15
Index 39
Chapter 3
Operation 17
About Touchmonitor Adjustments ..............................17
Front Panel Controls ............................................18
Controls and Adjustment ............................................19
OSD Menu Functions ..........................................19
OSD Control Options ...........................................20
Preset Modes.......................................................21
Power Management System ................................22
Display Angle .............................................................22
Chapter 4
Troubleshooting 23
Solutions to Common Problems .................................23
Appendix A.................................................... 25
Appendix B
Care and Handling of Your Touchmonitor ..................28
Appendix C
Touchmonitor Specifications ......................................30
AccuTouch Touchscreen Specifications .............31
12" LCD Touchmonitor (ET1215L-XXWA-1-G)
Dimensions .........................................................32
v
Product Description
Your new touchmonitor combines the relia ble perf ormance of touch technology with the latest
advances in LCD display design. This combination of f eatures creates a natural flow of information
between a user and your touchmonitor.
This LCD monitor incorporates 12” color active matrix thin-film-transistor (TFT) liquid crystal
display to provide superior display performa nce. A maxi mum resolution of SVGA 800x600 is ideal
for displaying graphics and images. Other outstanding de signs that enha nce this LCD monitor’s
performa nce are Plug & Play compatibility, and OSD (On Screen Display) controls.
CHAPTER
1
INTRODUCTION
NOTE Some monitors do not have the touchscreen capability.
Precautions
Follow all warnings, precautions a nd maintena nce a s recommended in this user’s manual to
maximize the life of your unit. See Appendix B f or more inf ormation on touchmonitor safety.
1-7
About the Product
Your LCD Desktop Touchmonitor is a 12” SVGA TFT color display with the following feature s:
• The internal microprocessor digitally controls auto-scanning. For horizontal sca n frequencies
between 31.5 KHz a nd 48 KHz, and vertical sca n frequencies between 56.3 Hz and 75.0 Hz. In
each frequency mode, the microprocessor -based circuitry allows the monitor to function at the
precision-of a fixed frequency.
• High contrast color TFT LCD display support resolution up to SVGA 800x600. Compatible with
V GA, SVGA(non-interlaced) and most M a cintosh compatible color video cards.
• Power ma nagement syste m conforms to VESA DPMS sta ndard.
• Supports DDC1/2B f or Plug & Play compatibility.
• Adva nced OSD control for picture quality adjustment.
• Detacha ble sta nd for wall-mounting a pplication.
• Optional touch screen function.
For full Product Specifications refer to Appendix C.
1-8 User Guide
CHAPTER
2
INSTALLATION AND SETUP
This chapter discusses how to install your LCD touchmonitor and how to install the driver software.
Unpacking Your Touchmonitor
Check that the following 8 items are present and in good condition:
LCD monitor V GA ca ble USB cable
Serial Ca ble European power cable Power cable US/Canada
Elo QuickStart
CD
Software
CD and Quick Install Guide
2-9
Touch Interface Connection
Note: Before connecting the cables to your touchmonitor and PC, be sure that the computer
and touchmonitor are turned off.
1. Connect one end of the power cord to the monitor and the other end to the outlet.
2. Connect one end of either the touchscreen serial(RS232) cable or the touch screen USB ca ble
(but not both) to the rear side of the computer a nd the other end to the LCD monitor. Tighten by
turning the two thumb screws clockwise to ensure proper grounding(optional module USB cable
does not have thumb screws)
3. Connect one end of the video ca ble to the rear side of computer and the other to the LCD monitor.
Tighten by turning the two thumb screws clockwise to ensure proper grounding.
4. Press the power button on the front panel to turn the monitor power on.
2-10 User Guide
Product Overview
Main Unit
Rear View
2-11
Installing the Driver Software
Elo TouchSystems provides driver software that allows your touchmonitor to work with your
computer. Drivers are located on the enclosed CD-ROM for the following operating syste ms:
• Windows XP
• Windows 2000
• Windows Me
• Windows 98
• Windows 95
• Windows NT 4.0
Additional drivers and driver information for other operating systems are available on the Elo
T ouchSystems web site at www .elotouch.com.
Your Elo touchmonitor is plug-and-play compliant. Information on the video ca pabilities of your
touchmonitor is sent to your video display a da pter when Windows starts. If Windows detects your
touchmonitor, follow the instructions on the screen to install a generic plug-and-play monitor.
Refer to the appropriate following section for driver installation instructions.
Depending upon whether you connected the serial communication cable or the USB
communication cable, you should install only the serial driver or the USB driver.
2-12 User Guide
Installing the Serial Touch Driver
Installing the Serial Touch Driver for Windows XP,
Windows 2000, Me, 95/98 and NT4.0
NOTE: For Windows 2000 and NT 4.0 you must have administrator access rights to install
the driver.
1 Insert the Elo CD-ROM in your computer's CD-ROM drive.
2 If the AutoStart feature f or your CD-ROM drive is a ctive, the syste m automatically detects the
CD and starts the setup program.
3 Follow the directions on the screen to complete the driver setup for your version of Windows.
4 If the AutoStart feature is not a ctive:
5 Click Start > Run.
6 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
7 Click Open, then OK to run EloCd.exe.
8 Follow the directions on the screen to complete the driver setup for your version of Windows.
To install Windows 2000 a nd Windows XP, you must use the "update driver" method; you will not
find a setup.exe file within the download.
2-13
Installing the Serial Touch Driver for MS-DOS and Windows 3.1
You must have a DOS mouse driver (MOUSE.COM) installed f or your mouse if you wish to
continue using your mouse along with your touchmonitor in DOS.
T o install Windows 3.x a nd MS-DOS from W indows 95/98, f ollow the directions below:
1 Insert the CD-ROM in your computer’s CD-ROM drive.
2 From DOS, type d:\EloDos_W31 to change to the correct directory on the CD-ROM (your
CD-ROM drive may be mapped to a different drive letter).
3 T ype install and press Enter to start the installation.
4 Align the touchscreen.
You must have alrea dy completed Steps 1 and 2 before proceeding.
T o run the INST ALL progra m:
1 T ype INSTALL at the DOS prompt in the directory containing the driver install files.
2 INSTALL a sks you to select the software to install. Then choose d:\EloDos_W31 from the
displayed list.
3 INST ALL also a sks you for the paths to use during installation, or you may use its defaults.
INST ALL create s directories a s necessary, a nd warns you if they exist.
If you are updating your software, you may wish to specify the paths containing the earlier versions,
a nd overwrite the obsolete files. All executable progra ms are upward compatible. For a list of
differences from ea ch previous version of the drivers, be sure to select "Diff erences from Previous
Versions" during the installation process.
INST ALL update s your AUT OEXEC.BA T file with the drivers you select. INST ALL makes a copy
of your original AUTOEXEC.BAT file, called AUTOEXEC.OLD. If you alrea dy have Elo driver
comma nds in your AUTOEXEC.BAT file, they will be commented out.
When INSTALL is finished, it leaves a file called GO.BAT in the subdirectory you specified. GO
loa ds the touchscreen driver, runs the calibration program ELOCALIB, and gives you some final
instructions.
If you are using W indows 3.1, you will also calibrate the touchscreen within Windows 3.1 with the
T ouchscreen Control Panel.
2-14 User Guide
Loading...