Tyco AS0073-001, RM-CAN, AS0074-000, RM-DCM-CAN, AS0073-CSI User Manual

DATA SHEET

Input/Output Modules

Features That Make a Difference:

Provides cost-effective expansion of input and output capacity
Compatible with full range of Software House® iSTAR and apC

access control panels

Locate modules up to 1,220 m (4,000 ft) away from controllers using

flexible two-wire RS-485 RM bus

Reduces length of sensor and control wiring to save installation

costs
I8 provides eight Class A supervised inputs
R8 provides eight Form C relay outputs
I8-CSI, configurable supervised input model, allows use of existing

input wiring without changing end-of-line (EOL) resistors
Three status LEDs per input (red/yellow/green) and one per output

enable quick diagnostics and troubleshooting
Small, modular size requires minimal panel space
Dedicated tamper input included on each module
Optional UL-listed enclosure available

The Software House I8, R8, and I8-CSI modules provide a
flexible, cost-effective means to expand the input and output
functionality of any iSTAR or apC access controller. Common
applications include alarm monitoring and control and elevator
control.

The I8 input module provides eight Class A supervised inputs.
Three LEDs per input help the installer commission and
troubleshoot each input circuit – red if the input is in alarm,
green for normal, and yellow for a supervision error. LEDs may
be turned off via a DIP switch setting.

The I8-CSI module enhances the functionality of the standard
I8 module by supporting numerous supervised circuit types and
EOL resistance values. This allows the I8-CSI to accommodate
existing field wiring without changing EOL resistors. More
than 20 different circuit types are supported. The circuit type
is selected via a bank of DIP switches and applies to all eight
inputs on the I8-CSI.

The R8 output module provides eight Form C dry contact relay
outputs. A red status LED per output shows the state of the
relay.

All modules feature a dedicated input for an external cabinet
tamper switch and mount easily in the Software House RM-CAN
or RM-DCM-CAN enclosure. The modules communicate with
iSTAR or apC controllers via the two-wire RM bus that allows
total wiring distances of up to 1,220 m (4,000 ft). Up to eight I8s
and eight R8s can be connected to each apC, iSTAR eX, and
iSTAR Pro eight-reader model; up to 16 of each module can be
connected to the iSTAR Pro 16-reader model.

®

The modules are fully compatible with both C•CURE
and C•CURE 9000.

800/8000

SPECIFICATIONS

0

1

2

3

F

E

D

C

B

A

4

5

6

7
8
9

1

SW1

4

SOFTWARE HOUSE

MADE IN USA

P9

P2

P3

P4

P8

P7

P6

P5

W1

TAMPER
INPUT

P1

R8 OUTPUT MODULE

AS-0074-000 REV.A

NO

NO

NO

NO

NO

NO

NO

NO

NC

NC

NC

NC

NC

NC

NC

NC

C

C

C

C

C

C

C

C

NOTE: All mounting holes are 1/8" dia.

Max. component height 1/2".

23

1

2
3

1

2
3

1

2
3

1

2
3

1

2

3

1

2

3

1

2

3

1

2

3

Pb

Pb-Free

P5

INE 1

P6

INF 1

P7

ING 1

P8

INH 1

P10P9

GND GNDTS +D -D+12V

1

1

P4

IND 1

P3

INC 1

P2

INB 1

P1

INA 1

S1-1 ON = LED Power
S1-2 ON = Disable Tamper
S1-3 ON = Not Used
S1-4 ON = 485 Termination

DS4

DS25

DS3

DS2

DS27Y1DS26

DS1

DS24

DS23

DS22

S3

1 2 3 4

NO

DS21

DS20

DS7

DS6

DS5

DS10

DS9

DS8

DS13

DS12

DS11

S3

DS19

DS18

DS17

DS16

S2

1 2 3 4

ON

DS15

DS14

S2

S1

U3

FOR SWH STD 1K DUAL S2:3-4, S3:1-4 = OFF

SEE QUICKSTART DOC FOR OTHER SETTINGS

CYCLE POWER AFTER SETTING

1234

ON

S1

SW1

1

TYCO

SOFTWARE HOUSE

ASSEMBLED IN USA

C

COPYRIGHT 2007

"WARNING Damage may result from incorrectly
wiring power terminals, input and output lines, and
central-supervising station lines. Check all
connections before powering the unit."

0312–5008–01 Rev.

18–CSI BOARD

®

Input Rating P9
12VDC 125mA

Refer to Quick Start Installation Guide,
P/N UM-218, Rev B0, July 2008

General

Dimensions (H x W) .....11.0 x 15.0 cm (4.3 x 5.9 in)

Environmental.......... 0° to 50° C (32° to 122° F); 5 to 85% relative

humidity, non-condensing

Power Input Voltage .....12 VDC +/- 10%

Tam pe r ...............Dedicated input for external tamper switch

Weight................0.23 kg (8 oz)

Regulatory ............ UL 294, UL 1076, FCC Part A

CE, EN 50133, ROHS

I8 Input Module

Power Requirements ....180 mA @ 12 VDC

R8 Output Module

Power Requirements ....45 mA @ 12 VDC plus 32 mA per active relay

Outputs...............Eight Form C dry contact relays

LED per Output.........Red (relay active)

Relay Contact Ratings ... 30 VDC, 2.0 A resistive

30 VDC, 1.0 A inductive
125 VAC, 4.0 A

Optional Metal Enclosures with Tamper Switch

RM-DCM-CAN

Dimensions...........356 x 305 x 89 mm (14 x 12 x 3.5 in)

Capacity .............Up to four input or output modules

Inputs ................Eight Class A supervised

LEDs per Input ......... Red (alarm), green (normal), and yellow

(supervision error)

I8-CSI Input Module

Power Requirements ....80 mA @ 12 VDC

Inputs ................Eight Class A supervised, configurable via DIP switch

LEDs per Input ......... Red (alarm), green (normal) and yellow

(supervision error)

Circuits Supported ...... Single resistor: 1K, 5K, 10K

Double resistor: 1K, 5K, 10K,

RM-CAN

Dimensions...........210 x 184 x 83 mm (8.25 x 7.25 x 3.25 in)

Capacity .............One input or output module

Model Numbers

AS0 073-001 ...........I8 input module

AS0073-CSI ...........I8-CSI input module

AS0074-000 . . . . . . . . . . .R8 output module

RM-DCM-CAN .........Large metal enclosure with tamper switch

RM-CAN ..............Small metal enclosure with tamper switch

1K/2K, 6.8K/18K, 200/10K
Unsupervised: NO, NC

Wiring Summary

Signal From To Belden # Gauge # of Pairs Shielded Maximum Length

Comm

(two-wire RS485)

ap C/i STAR I8/R8 9841* 24 1 Yes

Power ap C/i STAR I8/R8 9841* 24 1 No

Control Point R8 Strike, Siren, etc. 8442/8461 18 1 No

Supervised Input I8 REX or Door Contact 8442/8461 22/18 1 No 610 m (2,000 ft)

1,220 m

(4,000 ft)

Based on

voltage drop

Based on

voltage drop

Wiring Configuration Diagram

I8 Input Module Configuration

R8 Output Module Configuration

Sample System Configuration: Combination Bus/Star Wiring Diagram

(*) For plenum or underground applications, use Belden 89182 for one pair 22 AWG, 100 ohm 12.95 pf/ft.

Note: Control, supervised, and unsupervised input cables must be shielded for FCC Class B operation.

Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies
by region; contact your sales representative. Certain product names mentioned herein may be trade names and/or registered trademarks of other companies.

© 2008 Tyco International Ltd. and its respective companies. All rights reserved. SH0146-DS-200810-R01-LT-EN

www.swhouse.com

I8-CSI Input Module Configuration