Tyco 33309 -0920 User Manual

ON/OFF
Switch

FEATURES

CONTENTS

TRANSMITTER

CHASSIS

Refer to label on transmitter and vehicle for frequency. Do not race vehicles with the same frequency.

FEATURES

■

2 Power Options

■

Full Function

■

27 MHz

■

Range up to 65'/20m

CONTENTS

33309 -0920

Left Stick

Controls

Forward and

Reverse

Right Stick
Controls Left
and Right
Turns

Power
Indicator
Light

Whip Antenna

NOTE: Your transmitter is
equipped with a special automatic
ON battery-saving feature. Just turn
your vehicle ON. Then push either
transmitter stick and you will be
able to run and control your vehicle.

This vehicle can operate on 2 different power
systems: the included 6V DP

™

Power Clip, which
uses 4 AA batteries (not included); and the 6.0V Jet
Turbo

®

rechargeable NiCd battery pack. You’ll find
detailed instructions about both systems in this
Owner’s Manual.

Gear Selector Switch
(Fast/Slow)

Steering Adjuster

Battery Compartment

Battery Latch

■

6V Dual Power™ Vehicle

■

(1) Transmitter

■

(1) 6V DP

™

Power Clip

Keep these instructions for future reference: they contain important information.

Your chassis may look slightly different, depending on your vehicle.

TRANSMITTER

POWER OPTION TWO - 6.0V JET TURBO
RECHARGEABLE NiCd BATTERY PACK

Please read Battery Charging/Care

on the next page.

1. Release battery compartment latch.

2. Insert battery pack into battery compartment and slide battery pack away from latch.

3.

Make sure battery pack snaps securely in place, turn battery compartment latch and lock
battery pack in place.

4. To remove battery pack, turn latch, slide battery pack toward latch and lift out.

1. Unscrew Power Clip cover

screw and remove cover.
Insert 4 AA batteries, with
polarity (+/-) as shown
inside Power Clip. Replace
cover.

2. Release battery compartment

latch.

3. Insert Power Clip into battery

compartment and slide Power Clip away from latch.

4.

Make sure

Power Clip

snaps securely in place, turn battery compartment latch and lock

Power Clip

in place.

5. To remove Power Clip, turn latch, slide Power Clip toward latch and lift out.

1. Slide battery door open.

2. Install one 9-volt (6LR61) battery with polarity (+/-) as shown inside

battery compartment.

3. Replace battery door.

POWER OPTION ONE - 6V DP POWER CLIP

POWER OPTION ONE - 6V DP POWER CLIP

(4 AA BATTERIES NOT INCLUDED)

POWER OPTION TWO - 6.0V JET TURBO
RECHARGEABLE NiCd BATTERY PACK

Battery Contacts

■ Bent or dirty contacts may result

in loss of power.

■ If battery does not fit correctly,

gently bend back metal contact as
shown in diagram.

IMPORTANT BATTERY INFORMATION

metal contact

TRANSMITTER

NOTE: The batteries used in the 6V DP P o wer Clip will gradually lose pow er o ver their lifetime.

You will notice a decrease in performance as this occurs. The 6.0V Jet Turbo rechargeable NiCd
battery pack will run at a sustained high power level for virtually its entire run time.

®

TM

■ Insure that battery polarity is

correct.

■ Use only batteries of the type

recommended (or equivalent).

■ Do not mix old and new batteries.

■ Do not mix alkaline, standard

(carbon-zinc), or rechargeable
(nickel-cadmium) batteries.

■ Remove used-up batteries

immediately. Remove batteries if
vehicle will not be used for a long
period.

■ For best performance use alkaline

batteries. Battery life may vary
depending on battery brand. Toy
performance may decrease as
batteries weaken.

■ Do not recharge

non-rechargeable batteries.

■ Do not short-circuit terminals.

■ Remove rechargeable batteries

before recharging.

■ Recharge batteries only under

adult supervision.

■ Dispose of batteries safely.