Tyco 0-1591046-X User Manual

16 Port 10/100Mbit/s
Ethernet Switch with Optional
Fiber Uplink Port
-
Product User Guide
Introduction
This Tyco Electronics auto-negotiating Fast Ethernet workgroup switch with optional fiber uplink enables clusters of up to 16 users to have high speed, low latency LAN connections to the corporate network.
Local management functions such as control of port speed, duplex mode, port trunking and VLAN membership are supported.
The optional fiber uplink module enables the switch to be connected using a fiber link to servers, routers and other devices over distances of up to 2km for multimode or 15km for singlemode.
Package Contents
Unpack the contents and verify them against the items below:-
1. 16 Port Ethernet Switch with fiber uplink option port
2. AC Power cord
3. Four rubber feet
4. Rack mounting kit (2 x brackets and 4 x screws)
5. RS-232 cable
If any item is damaged or missing, please contact your dealer.
Product Part No. 0-1591046-x (EMEA) PL0334 Issue 1.2
16 Port Ethernet Switch With Optional Fiber Port
Features
16 x Auto-sensing 10/100Base-T RJ-45 Ethernet ports1 x Option slot for 100Mbit/s fiber uplink module that
operates over distances of up to 2Km (multi-mode) or 15 Km (single-mode) fiber
1 x Additional 10/100Mbit/s RJ-45 port for uplinking Meets IEEE 802.3, .3u and .3x Ethernet standardsLocal management using an RS232 console portManagement enables detailed control of each portSupport for port-based VLANs and Port TrunkingUses store-and-forward switching to separate collision
domains and abnormal packet filtering
Integral 8K MAC address table automatic learningBackplane bandwidth up to 3.2Gbit/sSupports back-pressure & flow controlNumerous diagnostic LED indicatorsInternal AC/DC power unitStand-alone or mountable in 19” rackingFCC Class A, CE mark certification
Technical Support and Service
If you require technical advice for these products, please see the FAQ pages on the web address http://www.lan-electronics.com
If you still have problems, please contact us using the support form located on the above web site.
If you have a faulty unit then please contact us through the web site to arrange for a replacement unit. The faulty unit must be returned to us as part of the replacement agreement.
Tyco Electronics Page 2
16 Port Ethernet Switch With Optional Fiber Port
Front Panel
The front panel of the switch has 16 x RJ-45 Shielded/Unshielded Ethernet Ports, an optional fiber Ethernet 100Base-FX uplink port, a console management port and an array of LED indicators.
Figure 1 – Switch with optional fiber module (SC Connector) fitted
Ports
RJ-45 Ports. These Ethernet RJ-45 ports support both
shielded and unshielded cabling systems. The port auto­negotiates the 10/100Mbit/s network speed or can be forced by the console management interface into either 10Mbit/s or 100Mbit/s at either full-duplex or half-duplex.
Uplink RJ-45 Port. This port is intended for connection to
an uplink device without needing a cross-over cable. This is a standard 10/100Mbit/s Ethernet interface and shares the same port assignment as RJ-45 port 16. Therefore, do not use Port 16 when using this RJ-45 uplink.
100FX Fiber Port. This optional, field installable plug-in
module provides the fiber link to the distant media converter, NIC card or Ethernet switch. The port operates in either full duplex or half duplex modes depending on the setting of DIP switch on the front panel of the plug-in module. Modules with SC, ST and MT-RJ fiber optic connectors are available. See page 8 for order codes.
Console Port. A PC or other RS232 terminal is connected
to this port to enable detailed management of the switch. See the documentation on the web site for full information.
Rear Panel
The rear panel contains the 110/240v AC 50/60Hz power socket. Note that the fusing is external to the switch.
Tyco Electronics Page 3
Loading...
+ 6 hidden pages