TVLogic XVM-245W-N User Manual
Multi Format Broadcast
XVM-245W
24-Inch Full HD LCD Grade 1 Monitor
LCD Monitors
multi
Contents
CAUTION 4
OTHER FUNCTIONS 29
OPTIONAL ACCESSORY 38
This equipment has been tested and found to comply with the limits for class A digital device, pursuant to part 15 of the
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential to correct the interference at his own expense
CAUTION: Change or modications not expressly approved by the manufacturer responsible for compliance could void
the user’s authority to operate the equipment.
(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packing indicates that this product shall not be treated as household waste. Instead
it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative consequence for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of
materials will help to conserve natural resources.
Caution
ALWAYS USE SET VOLTAGE. AC 100 ~ 240V (1.6A/50~60HZ), DC 24V (TYP 3.2A) [ONLY XVM-245W]
All operating instructions must be read and understood before the product is operated.
These safety and operating instructions must be kept in safe place for future reference.
All warnings on the product and in the instructions must be observed closely.
All operating instructions must be followed.
Do not use attachments not recommended by the manufacturer. Use of inadequate attachments
can result in accidents.
This product must be operated on a power source specied on the specication label.
If you are not sure of the type of power supply used at your side, consult your dealer or local
power company. For units designed to be operated on batteries or another power source, refer to
the operating instructions.
The power cords must be routed properly to prevent people from stepping on them or objects
from resting on them. Check the cords at the plugs and product.
Do not overload AC outlets or extension cords. Overloading can cause re or electric shock.
Never insert an object into the product through vents or openings. High voltage ows in the
product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
Do not attempt to service the product yourself. Removing covers can expose you to high voltage
and other dangerous conditions. Request a qualied service person to perform servicing.
If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a
qualied service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions.
Improper adjustment of controls not described in the instructions can cause damage,
which often requires extensive adjustment work by a qualied technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality
in the product indicates that the product needs servicing.
In case the product needs replacement parts, make sure that the service person uses replacement
parts specied by the manufacturer, or those with the same characteristics and performance as the
original parts. Use of unauthorized parts can result in re, electric shock and/or other danger.
Caution
to ensure that the product is in proper operating condition.
When mounting the product on a wall or ceiling, be sure to install the product according to the
the product. Do not use liquid cleaners or aerosol cleaners.
swimming pool and in a wet basement.
to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or
sold with the product. When mounting the product on a wall, be sure to follow the manufacturer's
When relocating the product placed on a cart, it must be moved with the utmost care.
Sudden stops, excessive force and uneven oor surface can cause the product to fall from the cart.
The vents and other openings in the cabinet are designed for ventilation. Do not cover or block
these vents and openings since insu cient ventilation can cause overheating and/or shorten the
can block ventilation openings. This product is not designed for built-in installation; do not place
the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided
or the manufacturer's instructions are followed.
The LCD panel used in this product is made of glass. Therefore, it can break when the product is
dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the
The screen modes are dened as below:
- Normal or Single Mode : One input source (including Waveform) in one display.
- Multi Mode : Two input sources in one display(PBP).
Features
XVM SERIES HAVE THE FOLLOWING FEATURES:
Compatible with varied SDI signals
- The product is compatible with varied SDI Signals :
480i, 576i, 720p, 1080i, 1080p, 1080psF (SDI A, B 2channels are compatible)
Compatible with varied analog signals
- The product is compatible with varied analog signals : Composite, S-Video, Component, RGB, etc.
All-in-one type system
- Slim and all-in-one type monitor that requires no other accessory, for optimized space utilization.
Wide Screen compatible
- Wide Screen for easier monitoring conditions.
AC/DC compatible
- The product may be powered by normal AC source, but also 24V DC(XVM-245W)
- Remote-controlled simply with cable connection without additional peripheral equipment
attached to unit.
- DVI_I/HDMI(HDCP) Input is available without any other accessory.
- Supports based on attached protocol.
- Supports based on ethernet program download & Calibration.
- Supports based on program download.
Mounting Standard, 1000:1 contrast ratio(XVM-245W), 250cd brightness, User Interface and
Name & Function of Each Part
- Used when ANALOG INPUT is selected. Sub Menu for analog input menu-selection appears.
- Used when SDI INPUT A –> B is selected.
- Used to choose PBP or FULL screen.
- Used when transferring from OVER SCAN mode to UNDER SCAN mode.
(Compatible up to SD 1:1 SCAN mode.)
- Used when changing the monitor ratio on SD signal mode to 16:9.
- Used when indicating MARKER on the screen. The type of marker at work may be selected on the
main menu.
ANALOG
MODE
CHROMA/PHASE/SCREEN SEL
ASPECT
MENU
Name & Function of Each Part
- Used when checking horizontal sync and vertical sync simultaneously.
After applying Analog sync(CLK, H, V) check whether the SYNC is corresponding with SDI,
Component, Composite modes.
- You may remove R(red) and G(green) from the input signal and play the screen only in B(blue)
signal. And if the button hit twice, it will turn to MONO mode. (This mode use only luminance
value.)
- Used when changing the CHROMINANCE and PHASE values during menu in-activation. One time
of touch of the button will turn the product to CHROMA mode, and if the button is hit twice, to
automatic PHASE setting. (PHASE may be used only ANALOG mode.)
- Used to select a display in Multi Mode.
- Used when OSD menu is activated.
- Used when moving within the menus during OSD menu activation. It may also be used to control
the BRIGHT value during OSD menu inactivation.
- Used when moving within the menu during OSD menu activation. It may also be used to control
the CONTRAST value during OSD menu inactivation.
- Used when conrming a chosen value (or mode) during OSD menu activation or inactivation.
- It aords power supply, which may be indicated by indication lamp. The lamp is RED during power
supply and GREEN during system is in operation. In case of power cut and sudden shut o of the
power, the monitor keep previous setup stage.
- Used when power on and o.
- LED indicating monitors current status.
Name & Function of Each Part
- It provides connector to build connection with extra equipment for monitor control.
- When use our product at DVI display mode, DVI IN is input connector
- Use to Firmware(Ethernet) & Calibration.
- Signal input terminal used to put in COMPOSITE 1, S-VIDEO Y, COMPONENT Y, RGB G signals.
- Signal input terminal used to put in COMPOSITE 2, COMPONENT Pb RGB B signals.
- Signal input terminal used to put in COMPOSITE 3, S-VIDEO C, COMPONENT Pr, RGB R signals.
- Supports based on attached protocol.
CVBS1/Y/G/S-Y
CVBS2/Pb/B
CVBS3/Pr/R-S-C
DVI-I
SDI-A
SDI-B
EXT.SYNC
USB
RS232
REMOTE
RS422 IN
RS422 OUT
HDMI(HDCP)
ETHERNET
AUDIO
DC 24V IN
~AC IN
- SDI signal input terminal that provides A signal.
- SDI signal output terminal used for SDI A output.
- SDI signal input terminal that provides B signal.
- SDI signal output terminal used for SDI B output.
- Built in Audio Disembedder and Internal Speakers Stereo Audio out using phone jack.
External Audio in for Stereo Speaker out
- Supports based on program download.
- Used to supply AC power; 100V~240V input range.
- Used to supply DC power 24V(XVM-245W).
- Input VIDEO connection method.
Warning!!
When using the product, make sure to connect the GND rst before connecting the signal line.
There might be a possibility of wrong operation when the signal line is connected before GND. For
example, when using RCA-to-BNC (or BNC-to-RCA) connector, if you connect the signal line rst it
Name & Function of Each Part
CVS
YGY
CSoCo
.
3
CVS3C
CoectoCoosteCooetSdeo
Menu Organization & Adjustment
The product may be controlled and set system-wise through OSD displayed on the screen.
You may control various functions using MENU, UP/DOWN and ENTER buttons on the front bottom
of the monitor.
Menu control sequence follows the order below
1. Press MENU button to bring OSD menu on the screen.
2. Display the desired sub menu with the UP/DOWN button.
3. After select a sub menu, press ENTER to select an item with UP/DOWN button.
4. Press ENTER to select the desired item. (Veried by highlighted eld returning to
default black color.)
5. Press ENTER to save the new value (veried by highlighted eld returning to default black
color.)
6. Press MENU once to remove OSD menu from the screen.
7. To view next page in the sub menu, press ENTER button at PAGE I >> PAGE II.
- This item controls the degree of brightness between MIN(-100) and MAX(100).
CONTRAST
- This item controls the contrast ratio between MAX(100) and MIN(-100).
CHROMA
- This item controls saturation between MAX(50) and MIN(-50).
- This item controls PHASE value (Tone) between MAX(50) and MIN(-50). However, it is only
available on COMPOSITE and S-VIDEO among ANALOG modes.
APERTURE
- This item controls the picture sharpness. Sharpness select between MIN(-1) and MAX(5).
- This item sets the IRE value under NTSC mode between 0 IRE and 7.5 IRE.
- Only available in COMPOSITE 1/2/3 and S-VIDEO modes containing a NTSC signal.
VGA H POSITION
- This item controls VGA H position. It is only available on DVI analog mode.
VGA V POSITION
- This item controls VGA V position. It is only available on DVI analog mode.
Menu Contents
Loading...