Quick Start Guide
iNSPIRE iP300
600 Watt Powered Column Loudspeaker with 2 x 6.5" Woofers, 4 Neodymium Drivers,
KLARK TEKNIK Spatial Sound Technology, Reverb, Digital Mixer, Remote Control via
iPhone/iPad and Bluetooth Audio Streaming
2 iNSPIRE iP300
Important Safety
Instructions
LEGAL DISCLAIMER
LIMITED WARRANTY
Terminals marked with this symbol carry
electrical current of sucient magnitude
to constitute risk of electric shock.
Use only high-quality professional speaker cables with
¼" TS or twist-locking plugs pre-installed. Allother
installation or modication should be performed only
by qualiedpersonnel.
This symbol, wherever it appears,
alertsyou to the presence of uninsulated
dangerous voltage inside the
enclosure-voltage that may be sucient to constitute a
risk ofshock.
This symbol, wherever it appears,
alertsyou to important operating and
maintenance instructions in the
accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, donot
remove the top cover (or the rear section).
No user serviceable parts inside. Refer servicing to
qualied personnel.
Caution
To reduce the risk of re or electric shock,
do not expose this appliance to rain and
moisture. The apparatus shall not be exposed to dripping
or splashing liquids and no objects lled with liquids,
suchas vases, shall be placed on the apparatus.
Caution
These service instructions are for use
by qualied service personnel only.
Toreduce the risk of electric shock do not perform any
servicing other than that contained in the operation
instructions. Repairs have to be performed by qualied
servicepersonnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instruc tions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. Ifthe
provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Use only attachments/accessories specied by
themanufacturer.
12. Use only with the
cart, stand, tripod, bracket,
or table specied by the
manufacturer, orsold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualied service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
beendropped.
15. The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device shall
remain readily operable.
17. Correct disposal of this
product: This symbol indicates that
this product must not be disposed
of with household waste,
according to the WEEE Directive
(2012/19/EU) and your national
law. This product should be taken
to a collection center licensed for the recycling of waste
electrical and electronic equipment (EEE). The
mishandling of this type of waste could have a possible
negative impact on the environment and human health
due to potentially hazardous substances that are generally
associated with EEE. At the same time, your cooperation
in the correct disposal of this product will contribute to
the ecient use of natural resources. For more
information about where you can take your waste
equipment for recycling, please contact your local city
oce, or your household waste collection service.
18. Do not install in a conned space, such as a book
case or similar unit.
19. Do not place naked ame sources, such as lighted
candles, on the apparatus.
20. Please keep the environmental aspects of battery
disposal in mind. Batteries must be disposed-of at a
battery collection point.
21. Use this apparatus in tropical and/or
moderate climates.
MUSIC Tribe accepts no liability for any loss which
may be suered by any person who relies either
wholly or in part upon any description, photograph,
or statement contained herein. Technical specications,
appearances and other information are subject to
change without notice. All trademarks are the property
of their respective owners. MIDAS, KLARK TEKNIK,
LAB GRUPPEN, LAKE, TANNOY, TURBOSOUND,
TC ELECTRONIC, TC HELICON, BEHRINGER, BUGERA and
COOLAUDIO are trademarks or registered trademarks
of MUSIC Tribe Global Brands Ltd. © MUSIC Tribe Global
Brands Ltd. 2018 All rights reserved.
For the applicable warranty terms and conditions
and additional information regarding MUSIC Tribe’s
Limited Warranty, please see complete details online at
musictri.be/warranty.
Quick Start Guide 9
Thank you for choosing a TURBOSOUND loudspeaker product for your application. If you would like fur ther information about this or any other TURBOSOUND product,
please visit our website at turbosound.com.
Unpacking the Loudspeaker
After unpacking the unit please check carefully for damage. If damage is found, please notify your supplier at once. You, the consignee, must instigate any claim.
Please retain all packaging in case of futurere-shipment.
Controls
(1) ENCODER KNOB toggles between Graphic and Edit modes (when pressed) and changes parameter values (when rotated).
(2) LCD SCREEN displays the current DSP module and parameter settings.
(3) PROCESS but ton accesses the DSP signal processing menu.
(4) SETUP accesses the setup features menu.
(5) EXIT button saves changes and returns to the previous menu screen.
(6) ENTER but ton selects sub-menu or con rms parameter changes.
(7) INPUT A/INPUT B combo jacks accept input signals using XLR, balanced ¼" TRS or unbalanced ¼" TS connectors.
(8) LINK A/LINK B XLR connectors provide un-processed copies of the INPUT A or INPUT B signals.
(1)(2)
(7)
(8)
(4)
(6)
(5)
(3)
10 iNSPIRE iP300
iP300 DSP Menu Structure
Menu Sub-Menu Fullrange Function
Main Screen
Displays level indicators and model name.
Displays the following Bluetooth* statusinformation:
•
•Bluetoot h symbol indica tes connectio n to audio and/or
remote cont rol device (iPhone*, etc.).
•
•“ ” indicate s that the remote cont rol APP connecte d.
•
•“ ” indicate s audio streamin g is connected.
•
•“M” or “S” indic ates that the speaker i s linked to another iP
speaker as MA STER (left cha nnel, “M”) or SLAVE annel, “S” ).
Rotate the encoder knob to adjust the output volume.
Press the encoder knob enter the last used sub-menu.
Press the Process and Setup buttons to access sub-menus.
Volume Rotate the encoder to change the output volume.
PROCESS
INPUT
Sets input mixer level EQ and reverb for analogue input A and B,
as well as level for Bluetooth.
EQ (Equalisation)
Allows adjustment of three band equaliser with controls for bass,
midrange and treble.
MODE
Selects from 4 preset equalisations, depending on function and
music type.
POSIT (Position)
Selects DSP compensation depending on the speaker position:
stand, wall, corner.
SETUP Sets LCD back panel contrast, device lock and factory reset.
BT (Bluetooth)
Lets you pair the speaker with mobile Bluetooth devices and link to
another iP speaker as MASTER / SLAVE.
INFO Displays model and rmware information.
DFU
Indicates device is updating rmware from APP software
via Bluetooth.
*iPhone is a t rademark of Apple In c. The Bluetooth wo rd mark and logos are r egistered tra demarks owned by B luetooth SIG, Inc. an d any use of such mark s is under license.
iP Series Analogue Connection
Despite their sophistication, iP speakers offer straightforward analogue connectivity, and you can easily arrange the iP system to allow simple control of levels from
other devices, such as mixers. You can also daisy-chain multiple iP speakers using only the analogue connections, and then directly control the overall level from your
mixer’s master fader.
For example, you have four iP speakers and a mixer with simple left-right stereo outputs. For typical operation, set the DSP volume and input gain settings on all
speakers to a flat “0 dB” setting. Connect the mixer’s left and right stereo outputs to the first two speakers’ analogue INPUT A connections (the left and right mixer
outputs will go to separate speakers). Then, run cables from the OUTPUT analogue connections to the remaining two speakers. In a similar way, subwoofers can also be
linked to the analogue OUTPUT.
Quick Start Guide 11
iP Series Bluetooth Instructions
Bluetooth Connection
To stream audio from a Bluetooth-enabled device, you will need at least one iP speaker and an iPad*/iPhone/Android*/Windows* device with basic
Bluetooth connectivity.
With a streaming-only Bluetooth connection, all related iP DSP functions must still be controlled directly from the iP rear panel via the rotar y encoder.
For Apple* iOS devices, you can also download a dedicated TURBOSOUND iP Bluetooth app from the App Store. This iP Bluetooth app allows you to control a single or
stereo pair of iP speakers, including all DSP functions, remotely from your iOS device (see “Bluetooth Control” below for more information).
Bluetooth Streaming
To stream Bluetooth audio with any Bluetooth device (iPad/iPhone/Android/Windows, etc.)
Mono operation
1. Enable Bluetooth on your remote device.
2. Switch on your iP speaker and minimize the volume.
3. Select “Pair device” from the iP speaker’s Bluetooth menu.
4. Check that your remote device is searching for a connection.
5. Once your device detects the iP speaker, select the iP speaker from your remote device’s menu (e.g., “TURBOSOUND iP300”).
6. Wait until the remote device shows an active connection, and then check the speaker’s Bluetooth menu, which should display the name of the remote device
(e.g., “HUAWEI P7-L07”).
7. Bluetooth music can now be streamed to your iP speaker. The stereo signal will automatically mix down to mono.
8. The iP speaker will display the Bluetooth indicator on the main, top-level DSP screen.
Stereo operation
1. Complete the steps above to connect the fi rst speaker to Bluetooth audio.
2. The first connected speaker automatically becomes the MASTER speaker.
3. Switch on the second speaker, which becomes the SLAVE speaker.
4. Select “Link speaker” from the SLAVE speaker's Bluetooth menu.
5. The SLAVE speaker will display “Slave linking...”
6. Select “Link speaker” from the MASTER speaker’s Bluetooth menu.
7. The MASTER speaker will display “Master Linking...”
8. WAIT for the speakers to link.
9. Once the linking process is complete, Bluetooth audio will stream to the two speakers. The MASTER speaker will receive the left channel, and the SLAVE speaker will
receive the right channel.
10. MASTER and SLAVE connection will be indicated on the main, top-level DSP screens.
*iPad and App le are trademark s of Apple Inc. Andr oid is a trademark of G oogle Inc. Window s is either a regist ered trademark o r trademark of Micr osoft Corpo ration in the Unite d States and/or
other countries.
12 iNSPIRE iP300
Bluetooth Control
A dedicated iOS control app for TURBOSOUND Bluetooth speakers can be downloaded from the Apple Store.
This iOS control app can be used with Bluetooth pairing, or without pairing if only analogue inputs are used.
Operation with Bluetooth Pairing
•
•In both mono and stereo mode, first pair the MASTER speaker, and then launch the iOS control app.
•
•The iOS control app will automatically detect and adapt for mono or stereo mode.
•
•To alter the speaker settings, swipe the screen or press the settings icon. All iP speaker settings can be accessed from the iOS control app.
Operation without Bluetooth Pairing (Analogue Input Only)
•
•Power on the first (usually left-hand) speaker – this speaker will become the MASTER speaker.
•
•Start the control app on the IOS device.
•
•Check that the app is connec ted and functioning with the single MASTER speaker.
•
•Power up the second speaker – this speaker becomes the SLAVE speaker.
•
•Select "Link speaker" from the speaker Bluetooth menu in "Master" and "Slave" speaker to link each other.
•
•Check that the app’s Main Page shows both MASTER and SLAVE input and balance control.
Main Page (1 speaker) Main Page (2 speakers linked) Settings Page
DFU Firmware Update
Where possible please update your iP300 firmware using the iOS app.
To update, go to the Settings screen in the app and look for the “CURRENT FIRMWARE” section. This section of the Settings screen will show the current firmware
version. If a firmware update is needed, the screen will display this option:
•
•Swipe the update slider toward the right to initiate the firmware update. The update may take several minutes.
•
•Update progress will be displayed on the app and the iP300 speaker’s DSP screen.
Quick Start Guide 13
Firmware Update Fallback Procedure
In the event you are unable to update the firmware using the iOS or Android app, you may also carry out the update using this fallback procedure:
1. Download the .dfu file with the new firmware version to your smartphone.
2. Force your iP300 speaker into DFU update mode by following these steps:
a. Power off the speaker.
b. Hold the ENCODER KNOB.
c. Power on the speaker.
d. Please select the option “Firmware upgrade” then press the ENCODER KNOB.
e. When you are successful, the DSP screen will show the system is ready for the f irmware upgrade.
3. On your smartphone, select and hold the .dfu file until the smartphone of fers options for file transfer.
4. Select your smartphone’s function for sharing via Bluetooth.
5. Select the iP300 speaker for Bluetooth sharing (e.g., “HUAWEI P7-L07”).
6. When the download begins, the DSP screen will show the download progress.
7. When the download is complete, the speaker will auto-restar t and boot the new firmware.
IMPORTANT NOTE: The mounting of a permanently installed sound system may be dangerous unless undertaken by qualified personnel with the required experience
and certification to perform the necessary tasks. Walls, floors or ceilings must be capable of safely and securely supporting the actual load. The mounting accessory
used must be safely and securely fixed both to the loudspeaker and to the wall, floor or ceiling.
When mounting rigging components on walls, floors or ceilings, ensure that all fixings and fasteners used are of an appropriate size and load rating. Wall and ceiling
claddings, and the construction and composition of walls and ceilings, all need to be taken into account when determining whether a par ticular fixing arrangement
can be safely employed for a particular load. Cavity plugs or other specialist fixings, if required, must be of an appropriate type, and must be fitted and used in
accordance with the maker’s instructions.
The operation of your speaker cabinet as part of a flown system, if installed incorrectly and improperly, can potentially expose persons to serious health risks and
even death. In addition, please ensure that electrical, mechanical and acoustic considerations are discussed with qualified and cer tified (by local state or national
authorities) personnel prior to any installation or flying.
Make sure that speaker cabinets are set up and flown by qualif ied and certified personnel only, using dedicated equipment and original parts and components
delivered with the unit. If any parts or components are missing please contac t your Dealer before attempting to set up the system.
Be sure to observe the local, state and other safety regulations applicable in your country. MUSIC Group, including the MUSIC Group companies listed on the enclosed
“Service Information Sheet”, assumes no liability for any damage or personal injury resulting from improper use, installation or operation of the product.
Regular checks must be conducted by qualified personnel to ensure that the system remains in a secure and stable condition. Make sure that, where the speaker is
flown, the area underneath the speaker is free of human traffic. Do not fly the speaker in areas that can be entered or used by members of the public.
Speakers create a magnetic f ield, even if not in operation. Therefore, please keep all materials that can be affec ted by such fields (discs, computers, monitors, etc.)
at a safe distance. A safe distance is usually between 1 and 2 metres.
14 iNSPIRE iP300
Technical Specications
System
Frequency response
50 Hz – 20 kHz ±3 dB
40 Hz – 20 kHz -10 dB
Nominal dispersion 120° H @ -6 dB points
Maximum SPL 122 dB
Crossover type 2 way, active
Transducers
2 x 6.5" (167 mm) LF driver
4 x 2" (54.2 mm) HF driversr
Limiter Independent high, mid and low frequency
Amplifier
Maximum output power* 600 W
Type
LF: Class-D
HF: Class AB
Protection Short circuit, open circuit, thermal
Amplifier channels 2
Connectors
Input A / B 2 x combo jack / XLR
Sensitivity 4 dBu, nominal
Input impedance 16 kΩ unbalanced, 32 kΩ balanced
Maximum input level +22 dBu
Link output XLR
Mains supply IEC mains connector with integrated powerswitch†
Controls
Hardware Rotary push-encoder
Software iOS/Android interface via Bluetooth
DSP
Factory EQ presets Positioning, sound mode
Display LCD 128 x 32, blue, backlit
Level Main
Equalisation Bass, middle and treble
Protection Lock-out function for all settings
Input Mixer
Equalisation Bass and treble
Reverb KLARK TEKNIK design
Bluetooth Wireless Technology
Frequency range 2402 MHz ~ 2480 MHz
Channel number 79
Version Bluetooth 4.1 dual mode
Output 8 dBM
Compatibility Supports GATT/A2DP 1.2 prole
Maximum communication range 30 m typical
Connectivity Master-slave: stereo pairing link
Power Supply
Power consumption 80 W @ 1/8 max power
Voltage (fuses)
USA / Canada / Japan 100-120 V~, 50/60 Hz (T 6.3 A H 250 V)
UK / Australia / Europe 220-240 V~, 50/60 Hz (T 3.15 A H 250 V)
Korea / China 220-240 V~, 50/60 Hz (T 3.15 A H 250 V)
Enclosure
Dimensions (H x W x D) 713x 208 x 216 mm (28.1 x 8.2 x 8.5")
Net weight 11.9 kg (26.2 lbs)
Construction Engineering plastic (GXPP)
Finish Semi matt black paint
Grille Powder coated perforated steel
Accessories
— —
*independent of limiters and driver protection circui ts
Quick Start Guide 15
Other important information
1. Register online. Please register your new
MUSIC Tribe equipment right after you purchase it by
visiting turbosound.com. Registering your purchase using
our simple online form helps us to process your repair
claims more quickly and eciently. Also, read the terms
and conditions of our warranty, if applicable.
2. Malfunction. Should your MUSIC Tribe
Authorized Reseller not be located in your vicinity,
you may contact the MUSIC Tribe Authorized Fulller for
your country listed under “Support” at turbosound.com.
Should your country not be listed, please check if your
problem can be dealt with by our “Online Support” which
may also be found under “Support” at turbosound.com.
Alternatively, please submit an online warranty claim at
turbosound.com BEFORE returning the product.
3. Power Connections. Before plugging the
unit into a power socket, please make sure you are using
the correct mains voltage for your particular model.
Faulty fuses must be replaced with fuses of the same type
and rating without exception.
Important information
Loading...