Model RT2000 (X2)
Quick RefeRence Guide
THIS AREA FOR SERVICE PROVIDER
CONTACT INFORMATION:
TDN 07100-00098
Oct 31 2008
MANAGEMENT FUNCTIONS
- Access instRuctions -
1. At AtM WelcoMe scReen, pRess And hold doWn the <ctRl>
key (loWeR-RiGht coRneR of keypAd), pRess <1> key, then ReleAse
both keys. the pAssWoRd Access pRoMpt is displAyed.
2. enteR pAssWoRd And select <enteR>. the MAnAGeMent functions MAIN MENU is displAyed.
RESTART / SHUTDOWN TERMINAL
folloW Access instRuctions to enteR MAnAGeMent functions. select
SYSTEM PARAMETERS.
RESTART TERMINAL: this function Reboots the teRMinAl.
SHUTDOWN TERMINAL: this function poWeRs-doWn the teRMinAls
opeRAtinG systeM. When pRoMpted thAt shutdoWn is coMplete, tuRn
on/off sWitch on poWeR supply to <off> position.
TERMINAL CONFIGURATION REPORT
folloW Access instRuctions to enteR MAnAGeMent functions. select
DIAGNOSTICS > TERMINAL STATUS.
CONFIGURATION SUMMARY: this suMMARy is A coMpRehensive
RepoRt of cuRRent teRMinAl confiGuRAtion And hARdWARe stAtus
infoRMAtion.
note: it is hiGhly RecoMMended thAt this RepoRt be pRinted And sAved AfteR initiAl setup And WheneveR
chAnGes ARe MAde to the teRMinAls confiGuRAtion.
2
DIAGNOSTICS
folloW Access instRuctions to enteR MAnAGeMent functions. select
DIAGNOSTICS > DISPENSER.
PURGE: this instRucts the dispenseR to ReMove Any notes (jAMs) in
feed pAth.
TEST DISPENSE: this instRucts the dispenseR to dispense minimum
one note fRoM eAch instAlled cAssette into the Reject cAssette/AReA.
select DIAGNOSTICS > PRINTER.
RESET / TEST PRINTER: this
in st Ru ct s the pRin te R to Re-
initiAlize And peRfo RM A t est
pRintout.
CLOSE FUNCTIONS
folloW Access instRuctions to enteR MAnAGeMent functions. select
TERMINAL CLOSE FUNCTIONS.
dAy close: this option is used to coMplete dAily bAlAncinG of
the AtM With the pRocessoR. totAls ARe cleARed And sWitched to
the neXt business dAy.
tRiAl close: this option functions like A dAy close eXcept the totAls ARe not cleARed.
JOURNAL FUNCTIONS
folloW Access instRuctions to enteR MAnAGeMent functions. se-
lect JOURNAL.
pRint lAst X: to vieW/pRint pReviously Audited oR unAudited
RecoRds, use the pRint lAst X option.
eXAMple: enteRinG the nuMbeR ‘50’ Will let you vieW the lAst 50 tRAnsActions/events thAt hAve oc-
cuRRed. you MAy pRint to the Receipt pRinteR.
3
CASSETTE CLOSE FUNCTIONS
(fRoM the fRont displAy)
folloW Access instRuctions to enteR MAnAGeMent functions. select TERMINAL CLOSE functions.
select CASSETTE CLOSE.
select cAssette(s) to close. A check MARk ( √ )
identifies Which cAssette(s) ARe selected. pRess <en-
teR>.
A close RepoRt is displAyed to be pRinted oR sAved.
this opeRAtion Will Reset the nuMbeR of bills in the
cAssette(s) to zeRo (0). pRess <enteR>.
AfteR cAssette(s) hAve been ReinseRted in the dis-
penseR, pRess <enteR>.
plAce selected cAssette(s) IN SERVICE. pRess
<enteR>. note: For tDm-200/250 Dispensers.
enteR cAssette QuAntity (nuMbeR of notes, not
vAlue) foR the selected cAssette(s). pRess <enteR> to
Accept entRy. RepeAt foR eAch selected cAssette.
ReMove And Replenish the selected cAssette(s).
folloW cAssette ReplenishMent pRoceduRes.
A tRiAl cAssette close RepoRt AutoMAticAlly is
displAyed to be pRinted oR sAved. pRint And RetAin A copy
foR stARtinG point RefeRence. pRess <enteR> to RetuRn
to close functions.
**IMPORTANT**
ensuRe the Multiple AMount pARAMeteR MAtches
the denoMinAtion of cuRRency in eAch note cAssette!
4
CASSETTE CLOSE FUNCTIONS
(fRoM the ReAR opeRAtoR seRvice pAnel (touchscReen)
pRess to stARt.
enteR pAssWoRd.
se le ct “ t e RMi nAl cl os e
functions”.
select “cAssette close”.
close cAssette(s) - touch cAs-
sett e option s on to uchpAd until
“AsteRick” AppeARs. select “con-
tinue”.
Select the cassettes to close.
WARNING: Cassette totals will be
reset for the selected cassettes
* Cassette A: $10.00
* Cassette B: $20.00
Continue Exit
cAssette close RepoRt AppeARs.
pRint RepoRt. pRess “eXit” When
coMpleted.
*** Cassette Close ***
Cassette A
Last Close Date/Time:
6/4/2007 7:49:39 AM
Start Quantity:
Qty: 200
Amount: $2000.00
Dispensed:
Qty: 50
Amount: $500.00
Remaining:
Qty: 150
Amount: $1500.00
ReMove /Replenish cAssette(s).
You may now remove and replenish
the cassettes. Press ENTER when
done.
pRess “enteR”.
Enter
plAce cAssettes “in-seRvice”.
touch cAssette options on touch-
pAd u nt il “Ast eRi ck ” Ap pe ARs .
select “continue”.
Select the cassettes to place in
service.
* Cassette A: $10.00
* Cassette B: $20.00
Continue Exit
enteR cAssette Qty (eAch).
Cassette Quantity - Cassette A:
Please enter the number of bills that
are in the cassette (not the value).
tRiAl cAssette close RepoRt Ap-
peARs. pRint RepoRt. pRess “eXit”
When coMpleted.
*** Trial Cassette Close ***
Cassette A
Last Close Date/Time:
6/4/2007 7:55:39 AM
Start Quantity:
Qty: 200
Amount: $2000.00
Dispensed:
Qty: 0
Amount: $00.00
Remaining:
Qty: 200
Amount: $2000.00
pRess “ok”.
200
1 2
4
5
7
8
< >
0
3
6
9
CANCEL
CHANGE
OK
5
REPLENISH CASSETTE(S)
note: the Rt2000 utilizes tdM dispenseRs. cuR-
Rency ReplenishMent foR A cAssette is the sAMe
WhetheR its A sinGle oR duAl-cAssette dispenseR
MechAnisM.
STEP ACTION
unlock / open vAult
1
cAbinet dooR. the
dispenseR is Mount-
e d to A s li di n G
tRAy. note: the
t ra y Do es no t
neeD to be extenDeD
Fo r cu r re ncy re -
plenishment.
ReMove Reject cAssette by GRAspinG the
2
boX And pullinG fRoM the dispenseR.
unlock And ReMove Any Rejected notes.
STEP
plAce cAssette(s) on A flAt suRfAce.
4
ACTION
un lo ck not e cA s-
sette With supplied
k ey . op en l i d.
Move pusheR plAte
toWA R d s R e A R o f
cAssette And secuRe
in pl Ac e Wit h key
lAtch MechAnisM.
count the nuMbeR of bills thAt ReMAin in
5
the cAssette, if Any.
count the nuMbeR of bills thAt ARe beinG
Added to the ReMAininG notes.
the totAl of these AMounts Will be en-
teRed in the “enteR cAssette QuAntity”
pRoMpt foR cAssette close pRoceduRe.
close, lock, And ReinseRt the Reject cAs-
sette bAck into the dispenseR.
do not Recycle Rejected notes!
ReMov e the note
3
c A s s e t t e ( s ) b y
GRAspinG the GReen
hA nd le And pul l
fRoM the dispenseR.
plAce cuRRency in the cAssette And sloWly
6
ReleA se the lAtch AlloWinG the pAckeR
plAte to Move foRWARd AGAinst the notes.
cl os e l id , l o c k
cAssette And Rein-
seRt bAck into the
di s pe nse R. en su Re
cAssette is fully in-
seRted.
6
REPLENISH RECEIPT PAPER
note: this pRoceduRe ReQuiRes teRMinAl is poWeRed up.
STEP
1
2
ACTION
open the ReAR cAb-
inet sleeve dooR.
if pApeR ReMAins on
Roll, cut oR teAR
pA pe R b e t W e e n
Roll And pRinteR.
ReMove spent pA-
peR Roll And spin-
d l e f R oM pA pe R
bRAcket.
STEP
4
5
ACTION
ReleA se (Op en ) the blue tensi on lev eR
shoWn. ReMove Any pApeR fRoM the pRinteR/
cutteR AsseMbly.
Move the ten-
sion leveR bAck
to the CLOSED
po s it i on . Ro -
tAte doWn the
pRi nt eR Ass eM-
bly.
Closed
Open
instAll neW pApeR
Roll / sp in d l e in
bRAcket.
pApeR feeds f RoM
bottom of Roll!
pull ReleAs e pin,
3
GRAsp hAndle, And
RotAte pRinteR As-
seM bly up to t he
seRvice position.
note: this position
also allows receipt
access For printing
reports iF using the
rear service panel
feed end of pApeR
6
oveR bAR And into
p R i n t e R tA ke -u p
slot. pRinteR Will
A u t o MA t i cA l l y
GRip And pull pApeR
into feed pAth.
7
COMBINATION LOCKS
intRoduction
the secuRity cAbinet cAn be secuRed usinG eitheR A MechAnicAl oR electRonic coMbinAtion lock. this pAGe coveRs
hoW to opeRAte the coMbinAtion of eitheR lock.
opeRAtinG the MechAnicAl lock
unlockinG the lock
theRe ARe tWo MARks on the diAl RinG. the indeX At the top is used foR openinG the lock, the indeX 30 deGRees to
the left is used only When chAnGinG the coMbinAtion.
the diAl should AlWAys be tuRned sloWly And evenly. A Revolution is counted eAch tiMe the selected nuMbeR is
AliGned With the openinG indeX. Do not turn the Dial back to compensate For over-Dialing a number. if, When diAlinG
the coMbinAtion, Any nuMbeR is tuRned beyond the indeX, the entiRe seQuence Must be RepeAted.
unlockinG 3-nuMbeR coMbinAtions (foR eXAMple, “50-25-50”)
1. tuRn the diAl to the leFt At leAst fouR (4) coMplete tuRns to cleAR the coMbinAtion lock to Accept the
coMbinAtion.
2. usinG the ‘openinG indeX’, tuRn the diAl to the leFt, stoppinG When ‘50’ is AliGned With the openinG indeX,
the Fourth tiMe.
3. tuRn the diAl to the right, stoppinG When ‘25’ is AliGned With the openinG indeX, the thirD tiMe.
4. tuRn the diAl to the leFt, stoppinG When ‘50’ is AliGned With the openinG indeX, the seconD tiMe.
5. tuRn the diAl sloWly to the right until the bolt RetRActs.
opeRAtinG the electRonic lock
the electRonic lock coMbinAtion consists of siX diGits. upon ARRivAl, the coMbinAtion of the lock should AlReAdy
be pReset to 1-2-3-4-5-6.
enteRinG the coMbinAtion
1. enteR the pReset coMbinAtion And check foR pRopeR opeRAtion. AfteR eAch keypRess, the lock Will beep. AfteR
the finAl diGit hAs been enteRed, the lock Will beep twice, And the open peRiod Will beGin.
2. When A vAlid coMbinAtion hAs been enteRed, the opeRAtoR Will hAve AppRoXiMAtely 4 seconDs to open the lock.
3. to open the lock, tuRn the Dial clockWise.
4. AfteR the lock is opened, the cAbinet dooR MAy be opened.
lockout feAtuRe
the lock includes A ‘wrong try penalty’ lockout feAtuRe thAt pRevents entRy fRoM unAuthoRized peRsonnel. this
feAtuRe peRfoRMs As folloWs:
• Entryoffour(4)consEcutivEinvalidcombinationsstartsa5-minutEdElaypEriod.
- led flAshes Red At ten (10) second inteRvAls.
• atthE End of thE dElay pEriod, two (2)morE consEcutivEinvalidcombinationswill rEstartan additional
5-Minute delAy.
8
Loading...