Model RL5000 (X2)
QUICK REFERENCE GUIDE
THIS AREA FOR SERVICE PROVIDER
CONTACT INFORMATION:
TDN 07100-00092B
Jan 29 2009
MANAGEMENT FUNCTIONS
- ACCESS INSTRUCTIONS -
1. AT ATM WELCOME SCREEN, PRESS AND HOLD DOWN THE <CTRL>
KEY (LOWER-RIGHT CORNER OF KEYPAD), PRESS <1> KEY, THEN RE-
LEASE BOTH KEYS. THE P ASSWORD A CCESS PROMPT IS DISPLAYED.
2. ENTER PASSWORD AND SELECT <ENTER>. THE MANAGEMENT FUNCTIONS MAIN MENU IS DISPLAYED.
RESTART / SHUTDOWN TERMINAL
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT SYSTEM PARAMETERS.
RESTART TERMINAL: THIS FUNCTION REBOOTS THE TERMINAL.
SHUTDOWN TERMINAL
NALS OPERATING SYSTEM. WHEN PROMPTED THAT SHUTDOWN IS COMPLETE,
TURN ON/OFF SWITCH ON POWER SUPPLY TO <OFF> POSITION.
: THIS FUNCTION POWERS-DOWN THE TERMI-
TERMINAL CONFIGURATION REPORT
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT DIAGNOSTICS > TERMINAL STATUS.
CONFIGURATION SUMMARY: THIS SUMMARY IS A COMPREHENSIVE
REPORT
OF CURRENT TERMINAL CONFIGURATION AND HARDWARE STATUS IN-
FORMATION.
NOTE: IT IS HIGHLY RECOMMENDED THAT THIS REPORT BE PRINTED AND SAVED AFTER INITIAL SETUP AND WHENEVER
CHANGES
ARE MADE TO THE TERMINALS CONFIGURATION.
2
DIAGNOSTICS
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT DIAGNOSTICS > DISPENSER.
PURGE: THIS INSTRUCTS THE DISPENSER TO REMOVE ANY NOTES (JAMS) IN
FEED
PAT H.
TEST DISPENSE: THIS INSTRUCTS THE DISPENSER TO DISPENSE MINIMUM
ONE
NOTE FROM EACH INSTALLED CASSETTE INTO THE REJECT CASSETTE/
AREA.
SELECT DIAGNOSTICS > PRINTER.
RESET / TEST PRINTER: THIS
INSTRUCTS
TIALIZE AND PERFORM A TEST PRINT-
OUT.
THE PRINTER TO RE-INI-
CLOSE FUNCTIONS
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT TERMINAL CLOSE FUNCTIONS.
DAY CLOSE: THIS OPTION IS USED TO COMPLETE DAILY BALANCING OF THE
ATM WITH THE PROCESSOR. TOTALS ARE CLEARED AND SWITCHED TO THE
NEXT
BUSINESS DAY.
TRIAL CLOSE: THIS OPTION FUNCTIONS LIKE A DAY C LOSE EXCEPT THE TOTALS ARE NOT CLEARED.
JOURNAL FUNCTIONS
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT JOURNAL.
PRINT LAST X: TO VIEW/PRINT PREVIOUSLY AUDITED OR UNAUDITED
RECORDS
, USE THE PRINT LAST X OPTION.
EXAMPLE: ENTERING THE NUMBER ‘50’ WILL LET YOU VIEW THE LAST 50 TRANSACTIONS/EVENTS THAT HAVE OC-
CURRED. YOU MAY PRINT TO THE RECEIPT PRINTER.
3
CASSETTE CLOSE FUNCTIONS
FOLLOW A CCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT TERMINAL CLOSE FUNCTIONS.
SELECT CASSETTE CLOSE.
SELECT CASSETTE(S) TO CLOSE. A CHECK MARK (
TIFIES WHICH CASSETTE(S) ARE SELECTED. PRESS <ENTER>.
√√
√ ) IDEN-
√√
A CLOSE REPORT IS DISPLAYED TO BE PRINTED OR SAVED.
T
HIS OPERATION WILL RESET THE NUMBER OF BILLS IN THE
CASSETTE
(S) TO ZERO (0). PRESS <ENTER>.
AFTER CASSETTE(S) HAVE BEEN REINSERTED IN THE DISPENSER,
PRESS <ENTER>.
N
OTE: IF AN NMD-50 DISPENSER IS INSTALLED, WAIT FOR THE
CASSETTES
TO LOCK (THIS IS DONE AUTOMATICALLY). PRESS
<ENTER> IF APPLICABLE.
PLACE SELECTED CASSETTE(S) IN SERVICE. PRESS <EN-
TER>. NOTE: SINGLE CASSETTE DISPENSERS (TDM-100/150,
SDD) AUTOMATICALLY “IN-SERVICE”. THE NMD-50 CASSETTES
MUST BE LOCKED AND IN SERVICE FOR NORMAL OPERATION.
ENTER CASSETTE QUANTITY (NUMBER OF NOTES, NOT
VALUE) FOR THE SELECTED CASSETTE(S). PRESS <ENTER> TO AC-
CEPT ENTRY. REPEAT FOR EACH SELECTED CASSETTE.
REMOVE AND REPLENISH THE SELECTED CASSETTE(S).
PROCEDURES FOR SPECIFIC DISPENSING MECHANISMS CAS-
SETTE REPLENISHMENT ARE ON THE FOLLOWING PAGES.
OTE: IF AN NMD-50 DISPENSER IS INSTALLED, WAIT FOR THE
N
CASSETTES
TO UNLOCK ( THIS IS DONE AUTOMATICALLY).
A TRIAL CASSETTE CLOSE REPORT AUTOMATICALLY
DISPLAYED TO BE PRINTED OR SAVED. PRINT AND RETAIN A
IS
COPY
FOR STARTING POINT REFERENCE. PRESS <ENTER> TO RE-
TURN TO CLOSE FUNCTIONS.
4
REPLENISH TDM CASSETTE
(TDM-100, -150)
NOTE: TDM-150 IS ON A SLIDING MOUNTING TRAY.
TDM-100
IS ON A STATIONARY TRAY.
STEP ACTION
UNLOCK/OPEN DISPENSER SECURITY DOOR. (FOR TDM-
1
150) RELEASE THE SLIDE LOCKING LEVER AND EXTEND
THE DISPENSER MOUNTING
TRAY
FULLY.
L
2
3
OCATE THE SPRING-LOADED LOCKING PIN ON UNDER-
SIDE OF TRAY. PULL PIN DOWN AND ROTATE SWIVEL
PLATFORM
PLACE
180° CLOCKWISE. RELEASE PIN TO LOCK IN
.
REMOVE REJECT CASSETTE. UNLOCK AND REMOVE ANY
NOTES
. DO NOT RECYCLE REJECTED NOTES!
CLOSE AND LOCK REJECT CLOSE AND REINSTALL IN DIS-
PENSER.
STEP
4
5
6
ACTION
REMOVE THE NOTE CASSETTE. UNLOCK AND MOVE PACKER
PLATE
TO REAR OF THE CASSETTE. LATCH IN PLACE WITH
THE
HOLD-BACK LATCH.
COUNT THE NUMBER OF BILLS THAT REMAIN IN THE CAS-
SETTE, IF ANY.
COUNT THE NUMBER OF BILLS THAT ARE BEING ADDED TO
THE
REMAINING NOTES.
THE TOTAL OF THESE AMOUNTS WILL BE ENTERED IN
THE
“ENTER CASSETTE Q UANTITY” PROMPT FOR CAS-
SETTE CLOSE PROCEDURE.
LACE CURRENCY IN THE CAS-
P
SETTE AND SLOWLY RELEASE THE
HOLD
-BACK LATCH ALLOWING
THE
PACKER PLATE TO MOVE
FORWARD
SLIDE THE CASSETTE BACK INTO THE DISPENSER.
PULL THE LOCKING PIN DOWN AND ROTATE SWIVEL PLAT-
FORM 180° COUNTERCLOCKWISE. R ELEASE PIN TO LOCK
IN
(FOR TDM-150) R E-
LEASE THE SLIDE LOCKING
LEVER
PENSER TRAY FULLY IN THE
CABINET
AGAINST THE NOTES.
PLACE.
AND SLIDE DIS-
.
5
REPLENISH TDM CASSETTE(S)
(TDM-200, -250)
STEP
1
2
3
ACTION
UNLOCK/OPEN DISPENSER
SECURITY
THE
AND
MOUNTING
DOOR. RELEASE
SLIDE LOCKING LEVER
EXTEND THE DISPENSER
TRAY FULLY.
LOCATE THE SPRING-
LOADED LOCKING PIN ON
UNDERSIDE
PIN
SWIVEL
CLOCKWISE. RELEASE PIN
TO
OF TRAY. PULL
DOWN AND ROTATE
PLATFORM 180°
LOCK IN PLACE.
REMOVE REJECT CASSETTE.
UNLOCK AND REMOVE ANY
NOTES
. DO NOT RE-
CYCLE REJECTED NOTES!
CLOSE AND LOCK REJECT
CLOSE
AND REINSTALL IN
DISPENSER
.
Reject cassette
STEP
REMOVE THE NOTE
4
CASSETTE
MOVE
PACKER PLATE TO
REAR
OF THE CASSETTE.
(S). UNLOCK AND
ACTION
LATCH IN PLACE WITH THE
HOLD
-BACK LATCH.
Note cassettes
COUNT THE NUMBER OF BILLS THAT REMAIN IN THE CAS-
5
SETTE, IF ANY.
COUNT THE NUMBER OF BILLS THAT ARE BEING ADDED TO
THE
REMAINING NOTES.
THE TOTAL OF THESE AMOUNTS WILL BE ENTERED IN
THE
“ENTER CASSETTE Q UANTITY” PROMPT FOR CAS-
SETTE CLOSE PROCEDURE.
PLACE CURRENCY IN THE CAS-
SETTE AND SLOWLY RELEASE THE
HOLD
-BACK LATCH ALLOWING
THE
PACKER PLATE TO MOVE
FORWARD
SLIDE THE CASSETTE BACK INTO THE DISPENSER.
6
PULL THE LOCKING PIN DOWN AND ROTATE SWIVEL PLAT-
FORM 180° COUNTERCLOCKWISE. RELEASE PIN TO LOCK IN
PLACE
RELEASE THE SLIDE LOCKING LEVER AND SLIDE DISPENSER
TRAY
AGAINST THE NOTES.
.
FULLY IN THE CABINET.
6
REPLENISH SDD CASSETTE
STEP ACTION
UNLOCK/OPEN DISPENSER
1
SECURITY
THE
REMOVE
CASSETTE MUST BE PRIMED WITH THE CASSETTE
KEY
2
KEY
TOR IN WINDOW.
SLIDE CASSETTE ON TO THE LOADING TRAY. LIFT LID TO
3
EXPOSE
DO NOT RECYCLE REJECTED NOTES!
DOOR. G RASP
CASSETTE HANDLE AND
THE CASSETTE.
BEFORE INSERTING ON THE LOADING TRAY. INSERT
AND TURN CLOCKWISE TO SHOW GREEN INDICA-
Cassette “primed”
***WARNING***
IF RED IS INDICATED IN THE WINDOW ON THE SIDE
OF
THE CURRENCY CASSETTE, NEVER ATTEMPT
TO
INSERT THE CASSETTE INTO THE DISPENSER OR
THE
LOADING TRAY!
THE REJECT TRAY. REMOVE ANY REJECT NOTES.
Green window
STEP
4
5
6
7
ACTION
LIFT THE REJECT TRAY.
PUSH THE PACKER PLATE
TO
REAR OF CASSETTE AND
LATCH
IN PLACE.
COUNT THE NUMBER OF BILLS THAT REMAIN IN THE CAS-
SETTE, IF ANY.
COUNT THE NUMBER OF BILLS THAT ARE BEING ADDED TO
THE
REMAINING NOTES.
THE TOTAL OF THESE AMOUNTS WILL BE ENTERED IN THE
“ENTER CASSETTE QUANTITY” PROMPT FOR CASSETTE
CLOSE PROCEDURE.
PLACE CURRENCY IN THE
CASSETTE
LEASE THE HOLD-BACK
LATCH
PACKER
FORWARD
NOTES
SETTE LID.
REMOVE CASSETTE FROM
LOADING
CASSETTE
“PRIME” THE CASSETTE
(“GREEN” INDICATOR).
INSTALL THE CASSETTE INTO
THE
AND SLOWLY RE-
ALLOWING THE
PLATE TO MOVE
AGAINST THE
. CLOSE THE CAS-
TRAY. INSERT THE
KEY AND
DISPENSER.
7
REPLENISH NMD-50 CASSETTE(S)
STEP ACTION
UNLOCK/OPEN DISPENSER SECURITY DOOR. GRASP CAS-
1
SETTE HANDLE WITH ONE HAND WHILE HOLDING MECHA-
NISM WITH THE OTHER.
PULL CASSETTE OUT
SLIGHTLY
, THEN PLACE
ONE
HAND UNDER-
NEATH. REMOVE CAS-
SETTE.
PRESS THE GREEN RELEASE BUTTON AND LIFT THE LID.
2
FLIP THE LID BACK FULLY LETTING IT REST ON A FLAT
SURFACE
.
STEP
5
6
ACTION
PLACE CURRENCY IN THE
CASSETTE
PACKER
NOTES
E
XTEND THE “PAWLS” ON
PACKER
CLOSE LID AND INSTALL IN
DISPENSER
AND MOVE
PLATE AGAINST THE
.
PLATE FULLY.
.
MOVE THE PACKER PLATE TOWARDS THE REAR.
3
OUNT THE NUMBER OF BILLS THAT REMAIN IN THE CAS-
C
4
SETTE, IF ANY.
COUNT THE NUMBER OF BILLS THAT ARE BEING ADDED
TO
THE REMAINING NOTES.
THE TOTAL OF THESE AMOUNTS WILL BE ENTERED IN
THE
“ENTER CASSETTE Q UANTITY” PROMPT FOR CAS-
SETTE CLOSE PROCEDURE.
REMOVE REJECT VAULT.
7
PEN VAULT BY ROTATING
O
GREEN RELEASE LEVER
“COUNTERCLOCKWISE”.
GRASP LID AND OPEN. RE-
MOVE ANY REJECTED
NOTES
. DO NOT RE-
CYCLE REJECTED NOTES!
R
OTATE GREEN RELEASE
LEVER
AGAIN AND CLOSE
LID
. INSTALL REJECT VAULT
IN
DISPENSER.
8
REPLENISH RECEIPT PAPER
NOTE: THIS PROCEDURE REQUIRES TERMINAL IS POWERED UP.
STEP
OPEN CONTROL PANEL. IF PAPER REMAINS ON
14
ROLL
, CUT OR TEAR PAPER BETWEEN ROLL AND
PRINTER
.
REMOVE SPENT
PAPER
ROLL AND
SPINDLE
FORM PA-
PER BRACKET.
PULL RELEASE
2
PIN
AND ROTATE
PRINTER
TER ASSEMBLY
DOWN
.
/ CUT-
ACTION
STEP
5
ACTION
INSTALL NEW PA-
PER ROLL/ SPINDLE
IN
BRACKET.
PAPER FEEDS
FROM
TOP OF
ROLL
!
FEED END OF PAPER INTO PRINTER TAKE-UP SLOT.
PAPER FEEDS OVER THE BAR! PRINTER WILL
AUTOMATICALLY
FEED
PAT H.
GRIP AND PULL PAPER INTO
RELEASE (OPEN) THE BLUE TENSION LEVER SHOWN.
3
REMOVE ANY PAPER FROM THE PRINTER/CUTTER
ASSEMBLY
.
MOVE THE TENSION
LEVER
BACK TO THE
CLOSED POSITION.
Open
ROTATE UP THE
PRINTER
SEMBLY.
/CUTTER AS-
Closed
RECOMMEND PERFORM A D IAGNOSTIC TEST OF
6
THE
PRINTER. GO TO MAIN MENU > DIAG-
NOSTICS > PRINTER > RESET/TEST
PRINTER. T HIS FUNCTION RE-INITIALIZES
AND
PERFORMS AN OPERATIONAL TEST OF THE
PRINTER
.
9
COMBINATION LOCKS
INTRODUCTION
THE SECURITY CABINET CAN BE SECURED USING AN ELECTRONIC COMBINATION LOCK. THESE
PAGES
COVER HOW TO OPERATE THE COMBINATION OF EITHER ELECTRONIC LOCK OFFERED.
OPERATING THE E LECTRONIC LOCK
THE ELECTRONIC LOCK COMBINATION CONSISTS OF SIX DIGITS. UPON ARRIVAL, THE COMBINA-
TION OF THE LOCK SHOULD ALREADY BE PRESET TO 1-2-3-4-5-6.
ENTERING THE COMBINATION
1. ENTER THE PRESET COMBINATION AND CHECK FOR PROPER OPERATION. AFTER EACH KEYPRESS, THE LOCK WILL BEEP. AFTER THE
FINAL
DIGIT HAS BEEN ENTERED, THE LOCK WILL BEEP TWICE, AND THE OPEN PERIOD WILL BEGIN.
2. WHEN A VALID COMBINATION HAS BEEN ENTERED, THE OPERATOR WILL HAVE APPROXIMATELY 4 SECONDS TO OPEN THE LOCK.
3. TO OPEN THE LOCK, TURN THE DIAL CLOCKWISE.
4. A
FTER THE LOCK IS OPENED, THE CABINET DOOR MAY BE OPENED.
LOCKOUT FEATURE
THE LOCK INCLUDES A ‘WRONG TRY PENALTY’ LOCKOUT FEATURE THAT PREVENTS ENTRY FROM UNAUTHORIZED PERSONNEL. THIS
FEATURE
PERFORMS AS FOLLOWS:
•ENTRY OF FOUR (4) CONSECUTIVE INVALID COMBINATIONS STARTS A 5-MINUTE DELAY PERIOD.
- LED FLASHES RED AT TEN (10) SECOND INTERVALS.
•AT THE END OF THE DELAY PERIOD, TWO (2) MORE CONSECUTIVE INVALID COMBINATIONS WILL RESTART AN ADDITIONAL 5-MINUTE
DELAY
.
EACH LOCK IS SHIPPED FROM THE FACTORY IN SHELVED MODE, OPERATING ON A STANDARD COMBINATION (50-25-50).
ENTERING THE COMBINATION
1. TURN THE DIAL LEFT (CCW) UNTIL THE LETTERS “EC” (ENTER C OMBINATION) APPEAR
ON
THE LCD.
2. ENTER THE FACTORY COMBINATION OF 50-25-50 BY SEQUENTIALLY PRESSING THOSE SIX
(6) BUTTONS. THE LCD WILL DISPLAY THESE NUMBERS AS THEY ARE ENTERED.
3. WHEN THE COMBINATION HAS BEEN CORRECTLY ENTERED, THE LCD WILL READ “OPR”,
MEANING “OPEN RIGHT”. TURN THE DIAL RIGHT (CW) UNTIL IT STOPS. THE LOCKS
BOLT
IS NOW RETRACTED AND THE LOCK IS OPEN.
4. AFTER THE LOCK IS OPENED, THE CABINET DOOR MAY BE OPENED.
10
TO CHANGE THE COMBINATION:
1. POWER LOCK - EC
TURN THE D IAL TO THE LEFT (CCW) UNTIL “EC” (ENTER COMBINATION) IS DISPLAYED.
2. EC - ENTER SHELVED MODE COMBINATION - OPR
ENTER THE CURRENT COMBINATION (EITHER 50-25-50 OR A CHANGED COMBINATION) BY SEQUENTIALLY PRESSING THOSE DIGITS ON
THE
LOCK KEYPAD. THE NUMBERS WILL BE DISPLAYED ON THE LCD AS THEY ARE ENTERED.
3. OP
R - RETRACT BOLT
TURN THE DIAL TO THE RIGHT (CW) TO RETRACT THE BOLT
4. OPEN DOOR
5. INSERT CHANGE K EY
INSERT THE CHANGE KEY INTO THE CHANGE KEY SOCKET ON THE BACK OF THE LOCK.
6. EXTEND B OLT
TURN THE DIAL TO THE LEFT (CCW) TO EXTEND THE BOLT. DO NOT CLOSE THE DOOR
7. POWER LOCK - EC
TURN THE DIAL TO THE LEFT (CCW) UNTIL EC ( THE CHANGE KEY SYMBOL ALONG WITH ENTER COMBINATION) IS DISPLAYED.
8. EC - PRESS #8 - ECF
PRESS THE “#” BUTTON FOLLOWED BY THE “8” BUTTON. ECF (ENTER COMBINATION,FACTORY) WILL BE DISPLAYED.
9. E
CF - ENTER CURRENT S HELVED MODE COMBINATION - ENF
ENTER THE CURRENT SHELVED MODE COMBINATION, “ENF” (ENTER NEW FACTORY COMBINATION) WILL BE DISPLAYED
NF - ENTER N EW COMBINATION - CNF
10. E
SELECT AND ENTER THE NEW COMBINATION. “CNF” (CONFIRM NEW FACTORY COMBINATION) WILL BE DISPLAYED.
11. CNF - ENTER NEW COMBINATION - POC
ENTER NEW COMBINATION AGAIN TO CONFIRM. POC (PULL OUT CHANGE KEY) WILLBE DISPLAYED .
12. POC - REMOVE CHANGE KEY - EOP
REMOVE THE CHANGE KEY. EOP (END OPERATION) IS DISPLAYED.
13. EOP - P
TURN THE DIAL TO THE LEFT (CCW) UNTIL EC (ENTER COMBINATION) IS DISPLAYED.
14. EC - ENTER NEW SHELVED MODE COMBINATION - OPR
ENTER THE NEW SHELVED MODE COMBINATION BY PRESSING THOSE DIGITS ON THE LOCK’S KEYPAD. THE NUMBERS WILL BE DISPLAYED
ON
THE LCD AS THEY ARE ENTERED.
15. OPR - RETRACT BOLT
TURN THE DIAL TO THE RIGHT (CW) TO RETRACT THE BOLT.
16. CLOSE DOOR
17. EXTEND B OLT
TURN THE DIAL TO THE LEFT (CCW) TO EXTEND THE BOLT.
OWER LOCK - EC
11
COMMON ERROR CODES
ERROR
CODE
33
101
306
139
140
141
156
MEANING
FEED FAILURE
PRINTER CONTROL-
LER NOT RESPONDING
TIME-OUT WAITING
FOR
PRINTER TO BE
READY
PAPER JAM REPORTED
CASSETTE OUT OF
SERVICE
RECOMMENDATIONS
1. REMOVE AND OPEN CASSETTE(S). IF THERE IS CURRENCY IN CASSETTE, GO
TO
STEP 2. IF NOT, LOAD CURRENCY AND PROCEED TO STEP 3.
2. IS CURRENCY OF GOOD QUALITY? IF YES, GO TO STEP 4. IF NOT, OBTAIN
QUALITY
3. SHUFFLE CURRENCY AND REPACK CASSETTE.
4. RE-INSERT CASSETTE USING REPLENISHING CASSETTE P ROCEDURES.
5. PERFORM A T EST DISPENSE (DIAGNOSTICS>DISPENSER>TEST D ISPENSE).
IF SUCCESSFUL, PLACE ATM IN SERVICE.
1. VERIFY THAT THERE IS PAPER IN THE PRINTER. REPLENISH PAPER AS
NEEDED
2. PULL THE PRINTER RELEASE PIN. OPEN THE PRINTER/CUTTER ASSEMBLY
AND
THE
POSITION
3. PERFORM A RESET/TEST PRINTER (DIAGNOSTICS>PRINTER>RESET/
TEST PRINTER) COMMAND. IF SUCCESSFUL, PLACE ATM IN SERVICE.
1. THIS OCCURS WHEN THE LAST AVAILABLE CASSETTE DISPENSING
CURRENCYHAS
SERVICE
2. INSPECT CASSETTES. FILL IF NEEDED. IF THEY ARE NOT EMPTY, SEE RECOM-
MENDED ACTION FOR “FEED FAILURE” (ABOVE).
3. PLACE CASSETTES “IN-SERVICE” FROM MANAGEMENT FUNCTIONS MENU.
CURRENCY. PROCEED TO STEP 4.
.
VERIFY THERE ARE NO JAMS IN THE PRINTER OR THE PAPER PATH . VERIFY
BLUE LEVER ON THE LEFT SIDE OF THE PRINTER IS IN THE CORRECT
. CLOSE THE PRINTER/CUTTER ASSEMBLY.
BEEN TAKEN OUT OF SERVICE. CASSETTES ARE TAKEN OUT OF
BECAUSE OF FEED FAILURES OR EXCESSIVE REJECTS.
185
to
190
194
TERMINAL
CONFIGURATION
ERRORS
CASSETTES NOT
LOCKED
ENTER MANAGEMENT FUNCTIONS AND CHECK/CONFIGURE:
- TELEPHONE NUMBER (EC 185), CURRENCY VALUES (EC 186), MAXIMUM
WITHDRAWAL
NAL ID (EC 189), PIN MASTER KEY (EC 190).
IF WORKING WITH AN NMD-50 DISPENSER, LOCK THE CASSETTES FROM
MANAGEMENT FUNCTIONS MENU.
AMOUNT (EC 187), PIN WORKING KEYS (EC 188), TERMI-
12
Loading...