Midtopper Field installation Guide
direct liGhtinG (dc-powered)
Model 81XX/91XX (including X2)/97XX/Rl16XX
Rl23XX/Rl5XXX (XS/X2/XP) cabinetS
VERSION 5.0
TDN 07102-00043E 02/2009
81XX 91XX/RL23XX 97XX/RL5XXX
corporate headquarters:
522 E. Railroad Street
Long Beach, MS 39560
Phone: (228) 868-1317
Fax: (228) 868-0437
COPYRIGHT NOTICE
© 2008 Triton. All Rights Reserved. TRITON logo is a registered trademark of Triton
Systems of Delaware.
Midtopper Field installation Guide
iMportant notice
Triton Systems has discontinued offering a ballast/bulb (AC-powered) for
all lighted toppers. The Direct Lighting (DC-powered) Midtopper is a direct
replacement for both the ballast/bulb (AC-powered) and LED Light Panel
(DC-powered) versions. The Direct Lighting (DC-powered) Midtopper will
be the only available option.
The Direct Lighting (DC-powered) Midtopper is considered a complete
assembly with no serviceable parts. Any current model 91XX field
installations that still use the original hard-wired single power supply will
require the power extension cable (included in the kit).
The Direct Lighting Midtopper can be identied by the raised back panel,
versus the at back panel indicative of the AC ballast/bulb and the DC LED
Light Panel versions.
This manual will show the physical installation of the topper as well as the
individual DC power connection.
NOTE
Although the initial gures in this procedure depict a 91XX
cabinet (with a vertically mounted dual power supply),
the installation instructions are applicable to 81XX,
97XX, RL16XX, RL23XX, and RL5XXX (XS/X2/XP)
cabinets as well. The actual physical case characteristics
and mounting position of the DC power supply will vary
by model type. Any signicant differences will be noted
in the DC Connections section as applicable.
97XX Units!
Model 81XX, 91XX (including X2), RL16XX, RL23XX, RL5XXX
(XS/X2/XP) and most 97XX cabinets have topper mounting and access holes
in the top of the cabinet, consisting of four (4) small mounting holes and one
large access hole for internally routing the topper power cable.
Some early-model 97XX ATM cabinets do not possess a topper power cable
access hole; some cabinets have neither power cable access or mounting
holes: It is possible to cut holes in the cabinet to allow power cable access
and/or topper mounting, but such actions are to be undertaken at your own
risk! Triton Systems will accept no liability for damage that may occur to
the ATM and/or topper assembly in such cases.
2
direct liGhtinG (dc-powered)
Midtopper installation procedure
These procedures are completed with the terminal AC power OFF.
1. Remove the topper assembly from the shipping container.
2. Locate and remove the dome plugs (if applicable) to uncover the topper
power cable access and mounting holes on the top of the ATM cabinet,
3. Unlock and open the ATM control panel.
4. Feed the topper DC power cord through the large access hole in the cabinet.
With the topper mounting studs inserted into the four (4) corresponding
holes, place the assembly on top of the cabinet.
Note: Because of the slotted conguration of the mounting holes, there will
be some play (front-to-back) in the position of the topper assembly. Allow the
assembly to slide back until it stops.
Power Cord Access
Mounting Holes
Figure 1. Location of topper access and
mounting holes.
5. To secure the topper assembly to the cabinet, place and tighten #8-32 nuts
on the four (4) mounting studs with a 3/8” nut driver. Plug the topper power
cable into any available 8-pin connector on the DC power supply.
Figure 3. Place nuts on topper mounting
studs and tighten down.
Figure 2. Feed topper power cable
through cabinet access hole.
Figure 4. Connect the topper power
cable to the DC power supply.
3
Midtopper Field installation Guide
dc connections
Refer to the following notes and gures (as applicable to the model type of the
terminal). Plug the DC power cord from the topper (In most cases, an 8-pin molex
connector) into any available 8-pin* DC output connector on the power supply.
* A 10-pin DC output connector on a power supply is reserved for the dispenser.
1
Note: All model 91XX (except units using the original hard-wired single
supply in some TDM or MiniMech congurations), RL23XX, and RL5XXX
congurations use a single or dual power supply with the same physical case
characteristics and DC connector layout. The DC power supply itself will be
mounted in different locations within the top enclosure of the cabinet, depending
on the model type.
Model 8100 DC power supply
Model 97XX DC power supply
2Note: Refer to the following page. A Model 91XX with a TDM or MiniMech
dispenser and the original hard-wired single power supply will a require a power
extension cable (splitter).
Model RL16XX DC power supply
DC power supply used in some model
91XX, and all RL23XX/RL5XXX terminals
(see 1Note above)
4
direct liGhtinG (dc-powered)
Model 91XX w/TDM or Minimech and a hard-wired single power supply:
Locate the power extension cable (splitter) included in the kit. The cable
connectors are marked. Disconnect the mainboard power input and connect it
to one leg of the extension cable. Refer to the power extension cable (splitter)
conguration diagram below. Connect the midtopper DC power cable to the other
leg. Reconnect this power cable assembly back to the mainboard.
Model 91XX hard-wired single power
supply
Mainboard power disconnected.
LED Topper
Power Supply
Power extension cable (splitter) conguration.
Power extension cable
(splitter).
Power extension cable with topper and
mainboard power cables connected.
Main Board
6. Turn the power supply to ON (I). The topper sign should light up. Close and
lock the control panel.
5
Loading...