Tripp Lite SU80KTV, SU40K, SU60KTV, SU60K User Manual

Page 1
WARRANTY
REGISTRATION
Register online today for a
chance to win a FREE Tripp Lite
product! www.tripplite.com/warranty
SmartOnline™ 3-Phase UPS Systems
Owner’s Manual
Models: SU40K, SU60K, SU60KTV, SU80KTV
50/60 Hz, 3O, 4-wire + ground, wye
Not suitable for mobile applications.
1
2
3
4
5
6
7
8
9
10
11
12
1111 W. 35th Street, Chicago, IL 60609 USA
(773) 869-1234 • www.tripplite.com
Copyright © 2008 Tripp Lite. All trademarks are the sole property of their respective owners.
1
13
14
Page 2
Table of Contents
1
1 Introduction 3
2 Important Safety Instructions 4
2
3 Control Panel Features 6 4 Front and Rear Panel Features 7 5 Cabinet Installation 9
3
5-1 Preparation 9 5-2 Unpacking 9 5-3 Placement 10
6 Internal Battery Connection 11
4
(SU40K Only)
6-1 Internal Battery Wiring Diagrams 11 6-2 Internal Battery Connection Procedure 13
7 Wiring 16
5
7-1 Wiring Warnings 16 7-2 Wiring Preparation 16 7-3 UPS System Terminal Block Diagram 17 7-4 External Battery Cabinet Wiring Diagrams 17
6
7-5 Electrical and Cable Data 18 7-6 External Battery Cabinet Wiring 19 7-7 AC Input/Output Wiring (Single UPS) 20 7-8 AC Input/Output Wiring (Parallel UPS – Single Input) 21
7
8 Operating Modes 22
8-1 Online (Normal) Mode (Single UPS) 22 8-2 Battery Backup Mode (Single UPS) 22
8
8-3 Auto Bypass Mode (Single UPS) 22 8-4 Manual Bypass Mode (Single UPS) 22 8-5 Online Mode (Parallel UPS) 23 8-6 Battery Backup Mode (Parallel UPS) 23
9
8-7 Auto Bypass Mode (Parallel UPS) 23 8-8 Manual Bypass Mode (Parallel UPS) 24
9 Start-Up, Shutdown and Bypass 25
9-1 Control Panel and Breaker Diagrams 25
10
9-2 Preliminary Checklist (Single UPS) 25 9-3 Normal Start-Up Procedure (Single UPS) 25 9-4 Battery Start-Up Procedure (Single UPS) 26 9-5 Manual Bypass Procedure (Single UPS) 27
11
9-6 Shutdown Procedure (Single UPS) 27 9-7 Preliminary Checklist (Parallel UPS) 28 9-8 Start-Up Procedure (Parallel UPS) 28 9-9 Shutdown Procedure (Parallel UPS) 29
12
9-10 Manual Bypass Procedure (Parallel UPS) 30 9-11 Switching from Manual Bypass to Normal (Parallel UPS) 31
10 Display and Confi guration 32
10-1 Control Panel Diagram 32 10-2 Display Hierarchy 32 10-3 Default Display 33 10-4 Status Messages and Diagrams 33 10-5 Main Menu 35 10-6 UPS System “Measure” Menu 35 10-7 UPS System Setup Menu 36 10-8 Bypass Setup Menu 36 10-9 Output Setup Menu 37 10-10 Battery Setup Menu 38 10-11 Local Setup Menu 40 10-12 Maintenance Menu 41 10-13 Statistics Menu 42 10-14 Event Log Menu 43 10-15 Manual Setup & Test Menu 44 10-16 Firmware Upgrade Menu 45 10-17 Other Menu Choices 45
11 Communications 46
11-1 Communications Interfaces 46 11-2 SNMPWEBCARD Slot 46 11-3 Input Dry Contact Interface 46 11-4 Remote Emergency Power Off (EPO) Circuit Diagram 47 11-5 Auxiliary Dry Contact Input Circuit Diagram 47 11-6 External Battery Cabinet Temperature Inputs 47 11-7 External Battery Status Input 47 11-8 Output Dry Contact Interface Detail 48 11-9 Output Dry Contact Circuit Diagram 49 11-10 RS-232 Serial Port Circuit Diagram 50 11-11 Parallel Redundancy Port 50
12 Specifi cations 51
12-1 UPS System Technical Specifi cations 51 12-2 UPS System Floor Loading Table 51 12-3 Battery Pack Floor Loading Table 51
13 Storage and Service 52 14 Warranty and Warranty Registration 52
Español 53 Français 105
13
14
2
Page 3
1 – Introduction
Tripp Lite’s SmartOnline 3-Phase UPS Systems are ideal for backing up and protecting data centers, telecommunications (VoIP), networks, industrial facilities, security/emergency systems and more.
1
Advanced Features:
True on-line double conversion with superior IGBT inverter technology• Low input current THD allows 1:1 generator sizing for maximum efficiency and cost savings• Internal N+1 power module redundancy• Built-in parallel redundancy (1+1) capability for increased capacity or fault-tolerance• Up to 80kVA capacity in a compact footprint; up to 160kVA in parallel redundancy (1+1) configuration• High input power factor and high efficiency with low thermal loss and low noise• Simplified, easy-to-repair, long-life, high-availability system design• Redundant auxiliary power and control circuits• All models support external battery cabinets for extended battery backup runtime• High-resolution LCD status screen simplifies operation and delivers detailed operational information, including system block diagrams
2
3
4
5
6
7
8
9
10
11
12
13
14
3
Page 4
2 – Important Safety Instructions
1
SAVE THESE INSTRUCTIONS
All sections of this manual contains instructions and warnings that should be followed during the installation and operation of the UPS
2
systems described in this manual. Read all instructions thoroughly before attempting to move, install or operate the UPS systems described in this manual. Failure to comply may invalidate the warranty and cause property damage and/or personal injury.
Location Warnings
3
Install the UPS system in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and gasses, conductive • contaminants, dust and direct sunlight.
Install the UPS system in a level, structurally sound location.
4
The UPS system is extremely heavy; be extremely careful when moving or lifting the unit.• Operate the UPS system at indoor temperatures between 32° F and 104° F (0° C and 40° C) only. For best results, maintain indoor temperatures
between 62° F and 84° F (17° C and 29° C). Leave adequate space around all sides of the UPS system for proper ventilation. Do not block, cover or insert objects into the external ventilation
5
openings of the cabinet. Do not place any object on the unit, especially containers of liquid.• Do not mount the unit with its front or rear panel facing down (at any angle). Mounting in this manner will seriously inhibit the unit’s internal
cooling, eventually causing product damage not covered under warranty.
6
Do not install the UPS system near magnetic storage media, as this may result in data corruption. Keep all recorded magnetic media a minimum • of 60 cm (24 inches) away from the UPS system.
Do not attempt to stack the UPS system. Attempting to stack the UPS system may cause permanent damage and create a potential for serious • personal injury.
7
The casters are designed for minor position adjustments within the final installation area only. The casters are not designed for moving the UPS • system over longer distances.
The casters are not designed to provide long-term support for the UPS system after final installation. Use the levelers to provide long-term • support.
8
When moving the UPS system, push from the front or rear, not from the sides.• Do not attempt to unpack or move the UPS system without assistance.
Connection Warnings
9
The power supply for this unit must be three phase rated in accordance with the equipment nameplate. It also must be suitably • grounded according to all applicable local electrical wiring regulations.
The UPS system contains hazardous high voltages that have the potential to cause personal injury or death from electric shock.
10
11
12
The UPS system has its own energy source (battery – internal and/or external). The output terminals may be live even when the UPS system is • not connected to an AC supply.
If the UPS system receives power from a motor-powered AC generator, the generator must provide clean, filtered, computer-grade output.• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life
support equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.
The UPS system is designed to power modern computer loads and associated peripheral devices. Do not use the UPS system to power pure • inductive or capacitive loads.
Input and output wiring should be performed by trained, qualified electricians only.• Due to high leakage current, a proper earth ground connection is essential before connecting the AC supply.• Isolate the UPS system before working on the circuit. An easily accessible disconnect device should be incorporated in the fixed wiring. The
disconnect device must be a 4-pole device and must disconnect all line conductors and the neutral conductor.
13
14
4
Page 5
2 – Important Safety Instructions
Battery Warnings
The UPS system does not require routine maintenance. There are no user-serviceable parts inside. Only qualified service personnel should open • the access panels for any reason.
Batteries present a risk of electrical shock and burns from high short-circuit current. Battery connection or replacement should be performed • only by qualified service personnel, observing proper precautions. Turn off the UPS system before connecting or disconnecting internal batteries. Use tools with insulated handles. Do not open the batteries. Do not short or bridge the battery terminals with any object.
Replace batteries with equivalent batteries available from Tripp Lite. Do not operate the UPS system without batteries.• The batteries are recyclable. Refer to local codes for disposal requirements.• Do not dispose of the batteries in a fire, mutilate the batteries or open the battery coverings.• Battery fuses should be replaced by qualified service personnel only. Blown fuses must be replaced with the same number and type of fuses. • Potentially lethal voltages exist within the UPS system as long as the battery supply is connected. Service and repair should be performed
by trained personnel only, while the UPS system is turned off or placed into bypass mode. Disconnect internal batteries (if present) before performing any service work by switching off the internal battery circuit breaker and removing the battery fuse(s). Disconnect external batteries (if present) by switching off the external battery cabinet breaker and disconnecting the external battery cabling from the UPS system.
Do not connect or disconnect batteries when the UPS system is operating from the battery supply or when the unit is not in bypass mode.• Do not remove the plastic sleeves covering internal batteries.• Internal and external batteries must be replaced by equivalent batteries available from Tripp Lite.• Before connecting an external battery cabinet to the UPS system, read the external battery cabinet’s documentation. Use only external battery
cabinets that have been approved by Tripp Lite. If the UPS system remains off for an extended period of time, it should be turned on periodically to allow the batteries to recharge. The UPS
system should be turned on and the batteries should be recharged at least one uninterrupted 24-hour period every 3 months. Failure to recharge the batteries periodically may cause irreversible battery damage.
Wiring Warnings
See Section 7-1 for wiring warnings
1
2
3
4
5
6
7
8
9
10
11
12
13
14
5
Page 6
3 – Control Panel Features
1
A E F G H I J KBCD
2
3
4
“NORMAL” LED: This green light illuminates to indicate that the UPS system is in online (normal) mode. The primary AC input supply is
A
present and within standard operating parameters. “BATTERY” LED: This amber light illuminates when the UPS system is in battery backup mode, discharging the batteries to provide power
B
5
6
7
8
9
10
11
12
to connected equipment. An audible alarm will also sound. “BYPASS” LED: This amber light illuminates when the UPS system is in bypass mode (auto bypass or manual bypass). Battery backup
C
power will not be available to connected equipment while the UPS system is in bypass mode, but connected equipment loads will be supported by the bypass power source.
“FAULT” LED: This red light illuminates when any UPS system or input power fault occurs. Available diagnostic information will be
D
displayed on the LCD screen. LCD Status Screen: This illuminated LCD status screen displays text and graphics to indicate a wide range of UPS system operating
E
conditions and diagnostic data. Note: The LCD backlight will turn off after 10 minutes of inactivity. Turn on the backlight by momentarily pressing the ON button or one of the scroll buttons.
“ESC” (Escape) Button: Press this button to return to the previous page or menu.
F G
Scroll Buttons (
buttons are also used for data entry in several screens.
Enter Button (
H
ON Button: Press and hold this button for 3 seconds to turn the UPS system’s inverter ON.
I
J
OFF Button: Press and hold this button for 3 seconds to turn the UPS system’s inverter OFF. If the UPS system is in online (normal) mode, it will switch to auto bypass mode. Note: If the UPS system remains off for an extended period of time, the batteries should be recharged
periodically. The UPS system should be turned on and the batteries should be recharged at least one uninterrupted 24-hour period every 3 months. Failure to recharge the batteries periodically may cause irreversible battery damage.
“EPO” (Emergency Power Off) Button: Press this button to turn the UPS system’s output OFF and also disable bypass output.
K
If the UPS system is in battery backup mode when the EPO button is activated:
Main output and bypass output are turned off, the alarm sounds, fans shut down after approximately one minute, and control circuitry
remains active.
Releasing the EPO button (by pressing it again) turns off the UPS system completely, including the alarm and control circuit. Press the
ON button for 3 seconds to restart the UPS system.
If the UPS system is in online (normal) mode when the EPO button is activated:
Main output and bypass output are turned off, the alarm sounds, fans and control circuitry remain active.• Releasing the EPO button (by pressing it again) turns off the alarm and places the UPS system in auto bypass mode. Press the ON button
for 3 seconds to return the UPS system to online (normal) mode.
See
Section 10 – Display and Configuration for detailed information about the control panel’s menus and displays.
and ): Press these buttons to move the cursor up or down and navigate the control panel menus and screens. These
): Press this button to select a menu item or confirm a setting change.
13
14
6
Page 7
4 – Front and Rear Panel Features
A
B
1
2
3
C
E D
H H
SU40K shown (front)
I
4
5
F
G
6
7
8
9
Note: Individual models may vary from diagrams. Unit shown with front bezels removed.
Control Panel: The control panel allows the operator to monitor and control the UPS system. See
A
more information.
B
Internal Power Modules: 20kVA internal power modules can be replaced in the field without powering down connected equipment loads. The number of internal power modules varies by model. The internal power modules are capable of N+1 redundancy.
Internal Battery Pack Compartment (SU40K only): Internal batteries must be connected by a qualified electrician. See
C
Internal Battery Connection
Output Circuit Breaker Switch (Q4): Controls AC output power.
D
Manual Bypass Circuit Breaker Switch (Q3): Controls AC input power to the UPS system during manual bypass operation.
E
Bypass Input Circuit Breaker Switch (Q2): Controls AC input power to the UPS system during auto bypass operation.
F
Main Input Circuit Breaker Switch (Q1): Controls AC input power to the UPS system during online (normal) operation.
G
Levelers: The levelers provide long-term support for the UPS system.
H
Casters: The casters are designed for small position adjustments within the final installation location only; they are not designed for moving
I
the UPS system over longer distances. The casters are not designed to provide long-term support for the UPS system after final installation. Use the levelers to provide long-term support.
for more information.
7
Section 3 – Control Panel Features for
Section 6 –
10
11
12
13
14
Page 8
4 – Front and Rear Panel Features (continued)
1
L
2
3
4
J
M
K N
O
5
6
7
8
9
Note: Individual models may vary from diagrams. Unit shown with front bezels removed.
H
Levelers: The levelers provide long-term support for the UPS system.
I
Casters: The casters are designed for small position adjustments within the final installation location only; they are not designed for moving
10
11
12
13
the UPS system over longer distances. The casters are not designed to provide long-term support for the UPS system after final installation. Use the levelers to provide long-term support.
J
Accessory Slot: Remove the cover panel to install a Tripp Lite SNMPWEBCARD accessory. The SNMPWEBCARD accessory provides an Ethernet interface for the UPS system and enables remote monitoring and control via SNMP, Web browser or telnet. Call (773) 869-1234 for more information about the SNMPWEBCARD accessory.
K
RS-232 Serial Communications Port: This DB9 port connects the UPS system to compatible workstations or servers, enabling automatic shutdown during extended blackouts and monitoring of operating and power conditions.
L
Parallel Redundancy Port: This DB9 port connects the UPS system to another UPS system of identical type and capacity for use in a parallel redundancy (1+1) configuration. See
M
Input Dry Contact Interface: This interface receives dry contact signals that allow the UPS system to receive commands and monitor external battery conditions. See
N
Output Dry Contact Interface: This interface allows the UPS system to send information via dry contact communications. See
Communications
O
Internal Battery Circuit Breaker Switch (SU40K only): Controls the input/output power of the UPS system’s internal batteries. Terminal Block Cover: Remove the terminal block cover to access the UPS system’s input, external battery cabinet, output and grounding
P
connection terminals. Wiring conduits pass through the circular knockouts in the terminal block cover. See information, including a detailed diagram of the terminal block.
for more information.
Section 11 - Communications for more information.
H
SU40K shown (rear)
Section 7 – Wiring and Section 8 – Operating Modes for more information.
I
14
P
H
Section 11 –
Section 7 – Wiring for more
8
Page 9
5 – Cabinet Installation
1
Read Section 2 – Important Safety Instructions Before Installation
5-1 Preparation
The UPS system must be installed in a structurally sound area with a level floor that is able to bear the weight of the UPS system, any external battery cabinet and other equipment that will be installed nearby. The installation site should also have a dedicated AC circuit available that is compatible with the UPS system’s input requirements. (See requirements.) Before unpacking the unit, you should transport the shipping container closer to the final installation site to minimize the distance you will need to move the unit after the protective shipping container has been removed. If you plan to store the UPS system for an extended period before installation, follow the instructions in “Unpacking and Storage Instructions” sheet secured to the shipping container.) Warning: Do not attempt to unpack or move the UPS system
without assistance.
5-2 Unpacking
1-2
Inspect the shipping container(s) for visible damage. If you determine that the unit has been damaged during shipping, contact Tripp Lite for assistance. Do not attempt to use the UPS system if it has been damaged or mishandled.
Confirm that the shipping container is upright and use a screwdriver to remove its top panel, front panel and back panel. Also remove the plastic wrap and interior cushioning material. Confirm that the model name and rating at the rear of the cabinet match the unit you ordered. Examine the cabinet for any damaged or loosened parts. Confirm that the shipping container includes the accessories that ship with the unit. The UPS system should include an RS-232 serial cable, a parallel redundancy cable, a remote EPO wiring connector, a dry contact input connector (4 contacts), a dry contact output connector (12 contacts) and a software CD-ROM. If anything is missing or damaged, contact Tripp Lite for assistance.
Confirm that the unit is stable, then remove the side panels from the shipping container.
Section 12 – Specifications for details on input requirements and floor loading
Section 13 – Storage and Service. (Unpacking and storage instructions are also printed on the
1
2
3
4
5
6
7
8
Remove the bolts from the shipping brackets securing the unit
3
to the pallet, then remove the shipping brackets from the UPS system. Warning: Be extremely careful, as the unit could shift
unexpectedly.
Use several of the screws you removed in step 1 to attach the top panel of the shipping container to the front edge of the shipping pallet. The smooth surface of the panel should face upward so that it can be used as a ramp for rolling the unit off the shipping pallet. Do not attempt to use the top panel as a ramp if it is cracked or otherwise structurally damaged. Make sure the casters at the bottom of the unit are unlocked. Using extreme caution, slowly roll the unit down the ramp with the aid of several assistants.
9
10
2
11
12
13
3
14
9
Page 10
5 – Cabinet Installation (continued)
1
5-3 Placement
Use the casters to move the UPS system for a short distance over
1
2
3
4
5
6
7
8
9
a level, smooth, stable surface. Do not attempt to use the casters to move the UPS system over longer distances. The UPS system should be moved close to its final installation location inside its shipping container before it is unpacked from the shipping container. Use a mechanical device of sufficient capacity to move the shipping container. Warning: The UPS system could tip if it
is moved over an unstable surface. Be extremely careful when moving the UPS system. Push the UPS system from the front or rear, not from the sides.
2
Position the UPS system in a structurally sound area with a level floor that is able to bear the weight of the UPS system, any external battery cabinets and other equipment that will be installed nearby. The installation site should also have a dedicated AC circuit available that is compatible with the UPS system’s input requirements. (See the more information about input requirements and floor loading requirements.) The UPS system must be installed in a clean, secure environment with a relative humidity less than 90% (non­condensing). Operate the UPS system at indoor temperatures between 17° C and 29° C (62° F and 84° F). Prevent damage to cabling by using suitable protective conduits. In order to maintain proper airflow and service access, you must maintain the following clearances:
At least 100 cm clearance in front of the UPS system.• At least 50 cm clearance behind the UPS system.• At least 50 cm clearance above the UPS system.
Warning: The cooling fans circulate air from front to back. Do not use any air conditioning or fan that blows air directly toward the rear of the UPS system.
After moving the UPS system to its final location, lock the casters
3
A
and use the levelers B to stabilize the cabinet. Ensure that all
four levelers make firm contact with the floor.
Section 12 – Specifications for
1
50 cm
50 cm
100 cm
2
10
11
12
13
14
For emergency use, install a fire extinguisher rated for energized
4
electrical equipment fires (Class C rating or exact equivalent, with a non-conductive extinguishing agent) near the UPS system.
10
A
3
4
B
Page 11
6 – Internal Battery Connection (Model SU40K Only)
DANGER! LETHAL HIGH VOLTAGE HAZARD!
Potentially lethal high voltage exists within the batteries, even when not connected to a UPS system. Battery connection should be performed by qualifi ed service personnel only, following all the precautions listed in this manual and adhering to local electrical codes. Read
Section 2 – Important Safety Instructions before proceeding.
1
2
Internal battery connection is for model SU40K only. Each internal battery pack consists of two strings of batteries: one string with a black cable and one string with a red cable.
6-1 Internal Battery Wiring Diagrams
Review the internal battery wiring diagrams prior to connecting the internal batteries. The UPS system can accept up to four internal battery packs (each pack consists of two strings; each string consists of 10 batteries).
Q3
B+ N B-
XFMR XFMR
Q1Q2
B+ N B-
AC/DCMAIN I NPUT
UPS
12V, 20PCS 12V, 20PCS
12V, 20PCS 12V, 20PCS
SU40K shown
Q4
OUTP UTDC/AC
3
4
5
6
7
8
VBoard
B+
N
VBoard
B-
W1: RED, W2: BLUE, W3: WHITE, W4: BLACK
RED RED
BLACK BLACK
RED RED
BLACK BLACK
RED RED
BLACK BLACK
RED RED
BLACK BLACK
SU40K shown
12V, 9AH, 10PCS
W1
W2
W3
12V, 9AH, 10PCS
W4
9
12V, 9AH, 10PCS
W1
W2
W3
12V, 9AH, 10PCS
W4
10
12V, 9AH, 10PCS
W1
12V, 9AH, 10PCS
W1
W2
W2
W3
W3
12V, 9AH, 10PCS
12V, 9AH, 10PCS
W4
W4
11
12
13
14
11
Page 12
6 – Internal Battery Connection (continued)
1
6-1 Internal Battery Wiring Diagrams (continued)
2
3
4
5
6
10
11
12
UPS System
7
Battery Back
Connector
Fuse Block Bracket
8
UPS System
9
Battery Back
Connector
13
14
SU40K shown
12
Page 13
6 – Internal Battery Connection (continued)
6-2 Internal Battery Connection Procedure
Place the UPS system in bypass (or turn it completely off) and turn
1
off the internal battery circuit breaker switch, located on the rear of the UPS system.
1
2
3
Remove the battery access bezels, located on the front of the UPS
2
system.
3
Remove the battery cartridge fuses from each fuse block.
Disconnect the blue and white jumper cables attached to each fuse
4
block. Warning: When disconnecting the jumper cables, pull them straight away from the fuse block with even force. Do not wiggle them side-to-side, as this may damage the connector.
1
4
5
6
2
7
8
3
9
5
10
11
4
Remove the fuse block bracket. Note its orientation before removal.
12
13
5
14
13
Page 14
6 – Internal Battery Connection (continued)
1
6-2 Internal Battery Connection Procedure (contiinued)
Slide a battery string with a red cable into an empty slot within
6
2
the battery compartment. Make sure the battery string is oriented as shown in the diagram. Note: Start with the empty slots at the
bottom of the battery compartment and work toward the empty slots at the top of the battery compartment.
TERMINALS
3
SIDE VIEW
4
6
7
Slide a battery string with a black cable into an empty slot within the battery compartment, next to the battery string that you inserted
5
in step 6. Make sure the battery string is oriented as shown in the diagram. Repeat steps 6 and 7 as needed until all the battery strings have been inserted into the empty battery slots.
6
TERMINALS
SIDE VIEW
7
7
8
Reconnect the fuse block bracket. (The letters on the fuse block bracket should be upright when it is in the correct orientation.)
8
10
11
12
13
14
9
8
9
Connect the blue and white jumper cables on each internal battery pack to the corresponding fuse block. The labeling next to the fuse block identifies the correct fuse block for each cable.
9
10
Insert the battery cartridge fuses into each fuse block. The fuses are interchangeable. Make sure the fuses are firmly snapped into place.
Warning: Battery cartridge fuses must be inserted last due to potential arcing of connectors. Blown fuses must be replaced by a qualified electrician. Replace only with fuses of the same type and rating.
10
14
Page 15
6 – Internal Battery Connection (continued)
6-2 Internal Battery Connection Procedure (contiinued)
11
Use a voltmeter (user-supplied) to test the voltage of each internal battery pack. Observing proper polarity, connect the voltmeter’s black probe to the battery pack’s black connector; connect the voltmeter’s sure the voltmeter’s probes touch the metal contacts inside the battery pack’s connectors. The battery pack’s acceptable DC voltage range is between 220V and 280V DC (nominal 240V DC). If several voltmeter tests yield results outside the acceptable DC voltage range, contact Tripp Lite for assistance in determining the possible causes of the incorrect voltage reading before proceeding.
red probe to the battery pack’s red connector. Make
1
2
3
240
Connect the black cable for each internal battery pack to the
12
nearest black connector located inside the UPS system’s battery compartment. Connect the pack to the nearest battery compartment. Warning: Observe proper polarity by
connecting negative to negative (black to black) and positive to positive ( damage the UPS system and create a serious risk of personal injury and property damage.
13
Replace the battery access bezels.
14
Turn on the internal battery circuit breaker switch. If you placed the UPS system in bypass, return it to the previous operating mode. If you turned the UPS system off, turn it on. If you still need to wire the UPS system, proceed to
Note: If you need to remove or replace internal battery packs, modify steps 6 and 7 by removing and/or replacing the existing internal battery packs, as required.
red to red). Failure to observe proper polarity will
red cable for each internal battery
red connector located inside the UPS system’s
Section 7 – Wiring.
11
12
13
4
5
6
7
8
9
10
15
11
14
12
13
14
Page 16
7 – Wiring
1
DANGER! LETHAL HIGH VOLTAGE HAZARD!
2
7-1 Wiring Warnings
3
De-energize all input and output power sources of the UPS system before installing cables or making electrical connections.• Use flexible cable of sufficient length to permit UPS system servicing. The maximum cable length is 10 m (32.8 ft).• Use ferrule caps to cover termination cables and prevent frayed ends from shorting on the UPS system terminal block.
4
Use cabling rated VW-1, FT-1 or better.• Use cable sleeves and connector clamps.• The neutral conductor must be the same size as the current conductors.• Tighten all connections with a torque of at least 3.95 N·m (35 in·lb)
5
Confirm that all cables are marked correctly according to their purpose, polarity, phase and diameter.• If the UPS system’s input/output power source is wye-wye, then “Neutral” and “Ground” must not be connected.• If the input power source has VNG>0, install an isolation transformer before the UPS system and input power source, then connect the UPS
6
system’s “Neutral” and “Ground” together. For equipment requiring a neutral connection to an IT power distribution system, the disconnect device must be a four-pole device and must
disconnect all line conductors and the neutral conductor. If a disconnect device interrupts the neutral conductor, it must simultaneously interrupt all line conductors.
7
Allow the batteries to charge uninterrupted for 24 hours after the initial wiring connection.• Observe proper polarity by connecting negative to negative and positive to positive. Failure to observe proper polarity will damage the UPS
system and create a serious risk of personal injury and property damage. Observe proper phase by connecting R to R, S to S, T to T and N to N. Failure to observe proper phase will damage the UPS system and create a
8
risk of personal injury and property damage.
All wiring should be performed by a qualifi ed electrician, in accordance with the warnings in this manual and all applicable electrical and safety codes. Incorrect wiring may damage the UPS system severely and cause serious personal injury and property damage. Read
Section 2 – Important Safety Instructions before proceeding.
7-2 Wiring Preparation
De-energize all input and output (AC and DC) of the UPS system and external battery cabinet (if present).
9
Mark all cables according to their correct purpose, polarity, phase and diameter.• Review the diagrams in • Consult the table in
10
Note: If the UPS system’s input/output power source is wye-wye, then “Neutral” and “Ground” must not be connected. If the input power source has VNG>0, install an isolation transformer before the UPS system and input power source, then connect the UPS system’s “Neutral” and “Ground” together.
Section 7-3 and Section 7-4 to familiarize yourself with the terminal blocks.
Section 7-5 to find the correct electrical input/output characteristics for the UPS system.
11
12
13
14
16
Page 17
7 – Wiring (continued)
N
7-3 UPS System Terminal Block Diagram
1
2
Input
RRSSTTN
Grounding Terminals
External Battery
Connection
N+
7-4 External Battery Cabinet Wiring Diagrams
Output
3
N
4
5
6
7
8
External Battery Cabinet Breaker
Switch
+
+N–
SU40K and BP480V40C shown for illustration only; consult the battery cabinet’s documentation for exact specifications
9
10
11
12
13
14
17
Page 18
7 – Wiring (continued)
T
1
7-4 External Battery Cabinet Wiring Diagrams (continued)
2
3
4
5
6
7
7-5 Electrical and Cable Data
XFMR XFMR
Q1Q2
AC/DCMAIN INPUT
DC/AC
UPS
B+ B-N
B+ N B-
External Battery Cabinet B Cabinet: 26AH per Battery
C Cabinet: 40AH per Battery
12V, 20 Batteries 12V, 20 Batteries
Q3
Q4
OUTPU
Input and Output Battery Input and Output Battery Model Input/Output Breaker Size Fuse Size Cable Size Cable Size
8
SU40K 120/208V AC, 3O, 150A 120A 1/0 AWG 6 AWG 4-wire + ground, wye
SU60K 120/208V AC, 3O, 225A 160A 4/0 AWG 4 AWG 4-wire + ground, wye
9
SU60KTV 277/480V AC, 3O, 100A 160A 4 AWG 4 AWG 4-wire + ground, wye
SU80KTV 277/480V AC, 3O, 125A 220A 2 AWG 2 AWG 4-wire + ground, wye
10
11
12
13
14
18
Page 19
7 – Wiring (continued)
N
7-6 External Battery Cabinet Wiring
Warning: External battery cabinets vary. Read the external battery cabinet’s documentation before attempting to connect it to the UPS system. Use only external battery cabinets that have been approved by Tripp Lite.
Note: An external battery cabinet is required with models SU60K, SU60KTV and SU80KTV. It is optional with model SU40K. Contact Tripp Lite for external battery cabinet ordering information.
De-energize all input and output (AC and DC) of the UPS system
1
and external battery cabinet, and confirm that the external battery cabinet breaker switch been wired to an AC power source, see instructions.)
2
Remove the terminal block covers from the UPS system and external battery cabinet.
A
is off. (If the UPS system has already
Section 9-6 for shutdown
A
1
1
2
3
4
5
6
3
Connect the positive (+), neutral (N) and negative (-) UPS system connection terminals of the external battery cabinet to the corresponding positive (+), neutral (N) and negative (-) external battery connection terminals of the UPS system. See and the external battery cabinet’s documentation for terminal block diagrams. See
for cable size requirements. Cabling should be protected by
7-5
flexible conduit and routed through the appropriate knockouts in the terminal block cover. Warning: Observe proper polarity by
connecting negative to negative and positive to positive. Failure to observe proper polarity will damage the UPS system and create a risk of personal injury and property damage.
4
Connect the external battery cabinet’s grounding terminal UPS system’s corresponding grounding terminal (5.189 mm) ground cable. Keep the ground cable connected at all times after installation.
5
Connect the UPS system’s grounding terminal earth ground ground cable connected at all times after installation.
Replace the terminal block cover of the external battery cabinet. If
6
you do not plan to wire the AC input/output of the UPS system at this time, replace the terminal block cover of the UPS system.
Section 7-4 for wiring diagrams. See Section
B
with a 4 AWG (5.189 mm) ground cable. Keep the
Section 7-3
B
with a 4 AWG
A
to your facility’s
A
to the
2
+N–
+N–
7
8
9
3
10
A
B
4
11
12
B
A
65
19
13
14
Page 20
7 – Wiring (continued)
N
N
1
7-7 AC Input/Output Wiring (Single UPS)
After de-energizing all input and output (AC and DC) of the UPS
1
2
3
system, remove the terminal block cover from the UPS system.
10
4
If you did not connect the ground cable in
2
UPS system’s grounding terminal
B
with a 4 AWG (5.189 mm) ground cable. Keep the ground cable
connected at all times after installation.
Section 7-6, connect the
A
to your facility’s earth ground
1
5
B
6
3
Remove the UPS system’s front bezel to expose the circuit breakers. First, confirm that the main input circuit breaker switch
A
7
and the bypass input circuit breaker switchBare both off. Second, confirm that the manual bypass circuit breaker switch is off. Third, confirm that the output circuit breaker switchDis off.
C
2
D B AC
A
8
3
4
Confirm the phase of each cable, then connect the cables according
9
to the UPS system terminal block diagram in
Section 7-5 for cable size requirements. Cabling should be
protected by flexible conduit and routed through the appropriate knockouts in the terminal block cover. Warning: Observe proper
phase by connecting R to R, S to S, T to T and N to N. Failure to observe proper phase will damage the UPS system and create a risk of personal injury and property damage.
Section 7-3. See
R S T
R S T
11
12
13
14
4
5
Replace the UPS system’s terminal block cover.
+N
5
20
Page 21
7 – Wiring (continued)
7-8 AC Input/Output Wiring (Parallel UPS – Single Input)
Parallel Redundancy Warnings:
The total input cable length must be equal to the total • output cable length in order to prevent unbalanced load sharing between two UPS systems under reserve mode (i.e. IP1 + OP1 = IP2 + OP2; deviation must be <10%).
Parallel redundancy only supports 2 UPS systems (1+1 • redundancy ). Do not attempt to link more than two UPS systems via parallel redundancy.
The UPS systems must have the same rating and capacity • for parallel redundancy installation. Attempting to link dissimilar UPS systems will damage the UPS systems and create a serious risk of personal injury and property damage.
Follow the steps in
1
in the diagram.
2
Connect the included parallel redundancy cable redundancy port
Section 7-7, wiring the UPS systems as shown
A
to the parallel
B
of each UPS system.
1
AC I/P
IP1
IP2
Main I/P
Main I/P
UPS1
UPS2
O/P
Parallel Port
O/P
Parallel Port
1
2
OP1
3
Parallel Cable
Load
4
OP2
5
B
B
A
6
7
2
8
9
10
11
21
12
13
14
Page 22
8 – Operating Modes
1
This section provides a basic description of the UPS system’s operating modes. For more information about switching between operating modes,
Section 9 – Start-Up, Shutdown and Bypass.
refer to
2
8-1 Online (Normal) Mode (Single UPS)
In online (normal) mode, the UPS system’s rectifier converts incoming AC utility power to DC power that charges the batteries and supplies the inverter. The inverter transforms the DC power to precision-regulated,
3
pure sine wave AC power that supports the operation of connected equipment. This dual conversion technology isolates connected equipment from all power problems and ensures that connected equipment receives ideal power at all times.
4
8-2 Battery Backup Mode (Single UPS)
5
When a blackout or other extreme power event occurs, the UPS system automatically switches from normal mode to battery backup mode. The UPS system’s batteries (internal and/or external) provide emergency DC power to the inverter. The inverter transforms the DC power to precision-regulated, pure sine wave AC power that supports the
6
operation of connected equipment.
MAIN
MAIN
CB3
CB2
CB3
CB2
CB1
XFMR XFMR
CB1
XFMR XFMR
CB5
CB5
STS
STS
CB4
LOAD
CB4
LOAD
7
8-3 Auto Bypass Mode (Single UPS)
If the inverter malfunctions due to excessive temperature, overload, output short circuit, abnormal voltage or battery problems, the inverter
8
will shut down. If the UPS system detects a bypass power source that conforms to normal parameters, then the UPS system automatically switches to auto bypass mode to continue supplying power to connected equipment. When all problems are eliminated, the UPS system switches back to online (normal) mode automatically.
9
10
8-4 Manual Bypass Mode (Single UPS)
If UPS system maintenance or repair is required, you can bypass the UPS system and enable bypass power manually. After confirming that bypass power is present, switch the UPS system into manual bypass
11
mode. This allows service technicians to perform maintenance or repair jobs without interrupting the flow of AC power to connected equipment.
Warning: The UPS system must be de-energized completely before performing maintenance or repair by shutting it down completely after switching it to manual bypass mode.
12
MAIN
MAIN
CB3
CB2
CB3
CB2
CB1
XFMR XFMR
CB1
XFMR XFMR
CB5
CB5
STS
STS
CB4
LOAD
CB4
LOAD
13
14
22
Page 23
8 – Operating Modes (continued)
8-5 Online Mode (Parallel UPS)
Parallel redundancy (1+1) provides UPS system redundancy or increased total capacity. Under parallel redundancy, the total load is shared by two UPS systems. If one of the UPS systems malfunctions, the total connected equipment load is supported by the remaining UPS system. If the total load exceeds the capacity of the remaining UPS system, it will switch to auto bypass mode.
MAIN
CB3
CB2
CB3
CB1
XFMR XFMR
CB5
STS
1
2
CB4
3
UPS1
LOAD
4
8-6 Battery Backup Mode (Parallel UPS)
Similar to on battery backup mode for a single UPS system (Section
8-2
), except the total connected equipment load is shared by the parallel
(1+1) UPS systems.
MAIN
MAIN
MAIN
CB2
CB3
CB2
CB3
CB2
CB1
XFMR XFMR
CB1
XFMR XFMR
CB1
XFMR XFMR
CB5
CB5
CB5
STS
STS
STS
CB4
UPS2
CB4
UPS1
CB4
UPS2
LOAD
5
6
7
8
9
8-7 Auto Bypass Mode (Parallel UPS)
Similar to auto bypass mode for a single UPS system (Section 8-3), except with parallel (1+1) UPS systems.
23
MAIN
MAIN
CB3
CB2
CB3
CB2
CB1
XFMR XFMR
CB1
XFMR XFMR
CB5
CB5
STS
STS
CB4
UPS1
CB4
UPS2
10
11
12
LOAD
13
14
Page 24
8 – Operating Modes (continued)
1
8-8 Manual Bypass Mode (Parallel UPS)
Similar to manual bypass mode for a single UPS system (Section 8-4), except with parallel (1+1) UPS systems. Note: Both UPS systems must
2
be switched into manual bypass mode.
CB3
CB2
MAIN
3
CB3
CB1
XFMR XFMR
CB5
STS
CB4
UPS1
LOAD
4
MAIN
CB2
CB1
XFMR XFMR
CB5
STS
5
CB4
UPS2
6
7
8
10
11
12
13
14
9
24
Page 25
9 – Start-Up, Shutdown and Bypass
9-1 Control Panel and Breaker Diagrams
“NORMAL” LED
A
“BATTERY” LED
B
“BYPASS” LED
C
“FAULT” LED
D
LCD Status Screen
E
“ESC” (Escape) Button
F
Scroll Buttons (
G
Enter Button (
H
ON Button
I
OFF Button
J
“EPO” (Emergency Power Off) Button
K
Output Circuit Breaker Switch
L
Manual Bypass Circuit Breaker Switch
M
Bypass Input Circuit Breaker Switch
N
Main Input Circuit Breaker Switch
O
and )
)
E
A
B
C
D
F
I
G
J
H
K
Control Panel
L
Output
M
Manual Bypass
N
Bypass
Input
O
Main
Input
Circuit Breaker Switches (UPS System Front Panel)
1
2
3
4
5
6
9-2 Preliminary Checklist (Single UPS)
All circuit breaker switches should be off, including the breaker of the external battery cabinet (if present).• Confirm that no voltage potential exists between Neutral and Ground.• Confirm that the input power source matches the rating (voltage, frequency and phase) of the UPS system.
Note: After start-up, the UPS system will perform a brief self-test and display the results on the LCD screen. After a successful self-test, the UPS system will provide AC power to the connected equipment load.
9-3 Normal Start-Up Procedure (Single UPS)
If there is an external battery cabinet connected, switch on the
1
circuit breaker
2
Confirm that the manual bypass circuit breaker switch
A
of the external battery cabinet.
A
A
1
is off.
7
8
9
10
11
25
A
Output
2
Manual Bypass
Bypass
Input
Main
Input
13
14
12
Page 26
9 – Start-Up, Shutdown and Bypass (continued)
1
9-3 Normal Start-Up Procedure (Single UPS) (continued)
3
Switch on the output circuit breaker switch
2
circuit breaker switch
B
. After a brief initialization process, the LCD screen will show “ON AUTO BYPASS”, the “BYPASS” LED will illuminate and UPS system output will be supplied by the bypass power source.
3
4
Switch on the main input circuit breaker switch
4
power source is normal, the UPS system is ready for start-up.
5
Press the ON button
5
6
release the button. The inverter will activate and synchronize with the bypass source, then automatically switch from auto bypass mode to online (normal) mode. The “BYPASS” LED will darken and the “NORMAL” LED will illuminate.
A
for 3 seconds (until you hear a beep), then
A
and bypass input
A
. If the AC input
A B
Output Manual
3
Output Manual
4
Bypass
Bypass
Bypass
Input
Bypass
Input
A
Main Input
A
Main Input
7
9-4 Battery Start-Up Procedure (Single UPS)
8
Note: The battery must be at least partially charged for this operation to succeed.
If there is an external battery cabinet connected, switch on the
1
circuit breaker
A
of the external battery cabinet.
9
10
2
Confirm that the manual bypass circuit breaker switch
A
is off.
11
12
13
3
Press the ON button release the button. The inverter will activate and use stored DC battery power to supply AC power to connected equipment. The “BATTERY” LED will illuminate.
A
for 3 seconds (until you hear a beep), then
5
A
1
A
Output Manual
2
Bypass
Bypass
Input
A
Main
Input
14
3
26
Page 27
9 – Start-Up, Shutdown and Bypass (continued)
9-5 Manual Bypass Procedure (Single UPS)
Warning: Placing the UPS system in manual bypass will disable the inverter and power all loads from the manual bypass source, but the UPS system will still be energized. Before performing maintenance or repair on the UPS system, shut down and de-energize the UPS system completely by following the steps in they will not receive battery backup in the event of a utility power failure.
When the UPS system is in online (normal) mode, press the OFF
1
A
button
for 3 seconds (until you hear a beep), then release the button. The inverter will automatically switch to bypass mode and the “BYPASS” LED will illuminate.
Switch on the manual bypass circuit breaker switch
2
off the output circuit breaker switch
Section 9-6. Although connected equipment loads will be powered by the bypass power source,
A
1
A
, then switch
B
.
AB
1
2
3
4
5
Output Manual
2
Bypass
Bypass
Input
Main Input
9-6 Shutdown Procedure (Single UPS)
Warning: The UPS system shutdown procedure will eliminate the AC power output for all loads. Before shutdown, confirm that all loads are turned off or place the UPS system in manual bypass mode to keep loads powered by the bypass power source.
Press the OFF button
1
release the button. If the UPS system is in online (normal) mode, it will switch to bypass mode. If the UPS system is in battery backup mode, the inverter will shut down and AC output power will be interrupted.
2
Switch off the main input circuit breaker switch
3
Switch off the bypass input circuit breaker switch
A
for 3 seconds (until you hear a beep), then
A
.
A
.
1
Output
2
Manual Bypass
Bypass
Input
A
Input
A
Main
6
7
8
9
10
11
27
12
A
3
Output
Manual Bypass
Bypass
Input
Main
Input
13
14
Page 28
9 – Start-Up, Shutdown and Bypass (continued)
1
9-6 Shutdown Procedure (Single UPS) (continued)
Confirm that the UPS system is off and that all main output circuits
4
2
3
4
5
6
7
8
are off. If the UPS system is connected to an external battery cabinet, turn off the external battery cabinet circuit breaker switch
A
.
Switch off the output circuit breaker switch
5
power source is normal, the UPS system is ready for start-up.
Note: If the UPS system remains off for an extended period of time, it should be turned on periodically to allow the batteries to recharge. The UPS system should be turned on and the batteries should be recharged at least one uninterrupted 24-hour period every 3 months. Failure to recharge the batteries periodically may cause irreversible battery damage.
A
. If the AC input
4
Output Manual
5
A
A
Bypass
Bypass
Input
Main Input
9-7 Preliminary Checklist (Parallel UPS)
Warning: Parallel redundancy requires exactly two UPS systems (1+1 redundancy). Do not attempt to link more than two UPS systems via parallel redundancy. The UPS systems must have the same rating and capacity for parallel redundancy installation. Attempting to link dissimilar UPS systems will damage the UPS systems and create a serious risk of personal injury and property damage.
All circuit breaker switches should be off, including the breakers of the external battery cabinets.• Confirm that no voltage potential exists between Neutral and Ground.• Confirm that the input power source matches the rating (voltage, frequency and phase) of the UPS systems.
You must use the control panel to set the parallel ID numbers of the UPS systems to be 1 and 2. See
about setting the parallel ID numbers.
Note: After start-up, the UPS systems will perform a brief self-test and display the results on the LCD screen. After a successful self-test, the UPS systems will provide AC power to the connected equipment load.
Section 10-11 for information
9
9-8 Start-Up Procedure (Parallel UPS)
Connect the parallel redundancy cable
1
redundancy port
B
of each UPS system.
10
11
If the UPS systems have external battery cabinets connected,
2
switch on the external battery cabinet circuit breaker switch each battery pack.
12
13
14
A
to the DB9 parallel
B
B
1
A
of
A
2
A
28
Page 29
9 – Start-Up, Shutdown and Bypass (continued)
9-8 Start-Up Procedure (Parallel UPS) (continued)
Switch on the bypass input circuit breaker switch
3
UPS system. After a brief initialization process, the LCD screen will show “ON AUTO BYPASS” and the “BYPASS” LED will illuminate.
4
Switch on the main input circuit breaker switch system.
5
Press the ON button
A
of one of the UPS systems for 3 seconds (until you hear a beep), then release the button. The inverter will activate and synchronize with the bypass source. Press the ON button for the other UPS system for 3 seconds (until you hear a beep), then release the button. When the inverter of each UPS system is operating normally, they will automatically switch from auto bypass mode to online (normal) mode at the same time. The “BYPASS” LED will darken and the “NORMAL” LED will illuminate.
6
Check the output voltage of each UPS system. The phase deviation between each UPS system should be less than 5V. If the phase deviation is within the acceptable range, switch on the output circuit breaker switch
A
of each UPS system. Note: For more
information on checking the output voltage of each UPS system, see
Section 10-6.
A
of each
A
of each UPS
3
4
5
Output Manual
Output Manual
A
Bypass
Bypass
A
Bypass
Input
Bypass
Input
Main
Input
Main Input
A
1
2
3
4
A
5
6
7
8
Output Manual
6
Bypass
Bypass
Input
Main Input
9-9 Shutdown Procedure (Parallel UPS)
Warning: The UPS system shutdown procedure will eliminate the AC power output for all loads. Before shutdown, confirm that all loads are turned off or place the UPS systems in manual bypass mode to keep loads powered by the bypass power source.
1
For the UPS system you wish to shut down, press the OFF button
A
for 3 seconds (until you hear a beep), then release the button. If the other UPS system can support the connected equipment loads alone, the UPS system that was turned off will shut down its inverter and its LCD screen will read “LOAD NOT POWERED”. The other UPS system’s LCD screen will read “ONLINE MODE”. If the total connected equipment load is too large to be handled by a single UPS system, both UPS systems will shut down their inverters and switch to bypass mode, and their LCD screens will read “ON AUTO BYPASS”.
2
For the UPS system you wish to shut down, switch off the main input circuit breaker switch breaker switch
B
.
A
, then switch off the output circuit
29
1
Output Manual
2
Bypass
Bypass
Input
A
Main Input
AB
9
10
11
12
13
14
Page 30
9 – Start-Up, Shutdown and Bypass (continued)
1
9-9 Shutdown Procedure (Parallel UPS) (continued)
For the UPS system you wish to shut down, switch off the bypass
3
2
input circuit breaker switch
3
When the UPS system is completely shut down, the LCD screen
4
will be completely off. If the UPS systems have external battery
4
5
6
7
8
9
cabinets connected, switch off the external battery cabinet circuit breaker switch
A
of each battery pack.
Note: If the UPS system remains off for an extended period of time, it should be turned on periodically to allow the batteries to recharge. The UPS system should be turned on and the batteries should be recharged at least one uninterrupted 24-hour period every 3 months. Failure to recharge the batteries periodically may cause irreversible battery damage.
9-10 Manual Bypass Procedure (Parallel UPS)
Warning: When the UPS system is in manual bypass, the inverter shuts down. Connected equipment loads are powered by the bypass power source and will not receive battery backup during a utility power failure.
For the first UPS system you wish to shut down, press the OFF
1
2
A
button
for 3 seconds (until you hear a beep), then release the button. If the other UPS system can support the connected equipment loads alone, the UPS system that was turned off will shut down its inverter and its LCD screen will read “LOAD NOT POWERED”. The other UPS system’s LCD screen will read “ONLINE MODE”. If the total connected equipment load is too large to be handled by a single UPS system, both UPS systems will shut down their inverters and switch to bypass mode, and their LCD screens will read “ON AUTO BYPASS”. Repeat step 1 for the second UPS system you wish to shut down.
Switch off the main input circuit breaker switch system.
A
.
A
A
of each UPS
Output Manual
3
4
1
Bypass
A
Bypass
Input
A
Main Input
A
10
11
12
13
14
3
Confirm that both UPS systems are shut down, then switch on the manual bypass input circuit breaker switch
A
of each UPS system. The bypass power source will power the loads and the LCD screen will read “ON MANUAL BYPASS”.
Switch off the bypass input circuit breaker switch
4
circuit breaker switch
B
of each UPS system. The LCD screen
A
and the output
will turn off completely.
30
Output
2
Output
3
Output
4
Manual
Bypass
A
Manual
Bypass
Manual
Bypass
Bypass
Input
Bypass
Input
AB
Bypass
Input
Main Input
Main Input
Main Input
Page 31
9 – Start-Up, Shutdown and Bypass (continued)
9-10 Manual Bypass Procedure (Parallel UPS) (continued)
If the UPS systems have external battery cabinets connected,
5
switch off the external battery cabinet circuit breaker switch each battery pack.
6
In this mode, only the output circuit breaker switch terminal block
B
contain hazardous voltage, allowing qualified
A
service personnel to perform maintenance or repair. Note: Qualified service personnel may prefer to de-energize the UPS systems completely, depending on local codes and the nature of the maintenance or repair.
and the
A
of
5
A
6
1
2
A
3
4
B
5
9-11 Switching from Manual Bypass to Normal Mode (Parallel UPS)
If the UPS systems have external battery cabinets connected,
1
switch on the external battery cabinet circuit breaker switch each battery pack.
2
Switch on the bypass input circuit breaker switch circuit breaker switch
3
Confirm that the LCD screens of both UPS systems read “ON
B
of each UPS system.
A
MANUAL BYPASS”, then switch off the manual bypass input circuit breaker switch
A
of each UPS system. The LCD screen
will read “ON AUTO BYPASS”. Switch on the main input circuit breaker switch
4
A
of each UPS
system.
5
Press the ON button
A
of the first UPS systems for 3 seconds (until you hear a beep), then release the button. Press the ON button for the second UPS system for 3 seconds (until you hear a beep), then release the button. When the inverter of each UPS system is operating normally, they will switch to online (normal) mode at the same time.
A
of
and the output
1
Output Manual
2
Output
3
A
Bypass
A
Manual Bypass
AB
Bypass
Input
Bypass
Input
Main Input
Input
A
6
7
8
9
10
11
Main
12
Output
Manual Bypass
Bypass
Input
A
Main
Input
31
13
54
14
Page 32
10 – Display and Confi guration
1
10-1 Control Panel Diagram
“NORMAL” LED
A
2
3
4
5
6
“BATTERY” LED
B
“BYPASS” LED
C
“FAULT” LED
D
LCD Status Screen
E
“ESC” (Escape) Button
F
Scroll Buttons (
G
Enter Button (
H
I
ON Button OFF Button
J
“EPO” (Emergency Power Off) Button
K
and )
)
10-2 Display Hierarchy
E
A
B
C
D
Control Panel
F
I
G
J
H
K
10
11
12
7
8
9
13
14
32
Page 33
10 – Display and Confi guration (continued)
10-3 Default Display
After the UPS system starts up and completes the self-test, the
1
LCD status screen will show the default display. The default display includes a status message and diagram that shows the operational status of the UPS system. If an alarm event occurs, an exclamation point will flash in the lower right corner of the LCD status screen.
Press the scroll down button (
2
may include diagnostic information. Press the scroll down button (
) again to see the next message. If no other event messages
exist, the screen will return to the default display. Note: Pressing
the “ESC” button will return to the default display.
) to see an event message, which
1
2
3
1
4
5
2
10-4 Status Messages and Diagrams
The UPS system output is off and the connected equipment loads
1
are not powered. This condition may be due to automatic UPS shutdown or manually switching off the output circuit breaker switch.
Connected equipment loads are powered by the bypass power
2
source at initial UPS system start-up.
3
The UPS system is starting up from battery power.
6
7
1
8
9
2
10
11
The UPS system is in auto bypass mode. Connected equipment
4
loads will lose power if the bypass power source fails.
33
3
12
13
4
14
Page 34
10 – Display and Confi guration (continued)
1
10-4 Status Messages and Diagrams (continued)
The UPS system is operating in online (normal) mode. Connected
5
2
3
4
5
6
equipment loads will receive battery backup power if the mains (utility or generator) power source fails.
The UPS system has switched to battery backup (on battery) mode.
6
Connected equipment loads are receiving battery backup power, and the estimated remaining runtime is shown. Note: The battery
parameters must be set correctly in order to receive accurate runtime estimates from the UPS system when it switches to battery backup mode. See
7
The UPS system has switched to battery backup (on battery) mode. Connected equipment loads are still receiving AC power inverted from battery power, but battery power is nearly depleted.
Section 10-10 for more information.
5
6
10
11
12
7
8
8
The UPS system is performing a battery test.
7
9
8
9
The UPS system is operating in economy mode, and connected equipment loads are being powered by the bypass source.
9
13
14
The UPS system is in manual bypass mode in order to allow
10
qualified service personnel to perform maintenance or repair on the UPS system. Connected equipment loads will lose power if the bypass power source fails.
10
34
Page 35
10 – Display and Confi guration (continued)
10-5 Main Menu
From the default display, press the enter button ( ) to access
1
the main menu. Press the scroll down button ( up button ( select one of the available menu options.
) to move the cursor. Press the enter button ( ) to
10-6 UPS System “Measure” Menu
Press the enter button ( ) to select “MEASURE” from the main
1
menu. Use the scroll buttons (
2
screens. Press the “ESC” button to return to the previous menu.
SU40K shown
or ) to scroll through the available data
) or the scroll
1
2
1
3
4
1
5
6
7
8
9
10
11
12
13
2
35
14
Page 36
10 – Display and Confi guration (continued)
1
10-7 UPS System Setup Menu
Press the enter button ( ) to select “UPS SETUP” from the main
1
2
3
4
5
6
menu.
Accessing the UPS system setup menu requires a password. From
2
the login screen, press the enter button ( to log in as an administrator or a user. Administrators can view and change all UPS system parameters; regular users can view all parameters, but can only change a few basic parameters. Only qualified service personnel should log in as the administrator.
3
The password consists of 4 numerals. Press the scroll down button (
) or the scroll up button ( ) to select the first numeral, then press the enter button ( entering the last numeral, press the enter button ( the password choice. The default user password is 0000. The default administrator password is 0000. Only qualified service personnel should have access to the administrator password. See
Section 10-11 for instructions on changing the passwords.
) to enter the numeral choice. After
) to select whether
) to confirm
1
2
7
After the correct password has been entered, the LCD screen will
4
show the UPS system setup menu.
8
9
10-8 Bypass Setup Menu
Enter the UPS system setup menu as described in Section 10-7.
1
10
Use the scroll buttons ( SETUP”, then press the enter button (
11
12
Use the scroll buttons (
2
“VOLTAGE RANGE” or “FREQUENCY RANGE”.
3
4
, ) to move the cursor to “BYPASS
).
1
, ) and the enter button ( ) to select
13
14
2
36
Page 37
10 – Display and Confi guration (continued)
10-8 Bypass Setup Menu (continued)
From the “VOLTAGE RANGE” screen, use the scroll buttons
3
, ) to select a bypass voltage range and press the enter button
( (
) to confirm the setting.
4
From the “FREQUENCY RANGE” screen, use the scroll buttons (
, ) to select a bypass frequency range and press the enter
button (
Note: Press the “ESC” button to return to the previous menu.
) to confirm the setting.
1
2
3
3
4
5
4
6
10-9 Output Setup Menu
Note: The UPS system must be in bypass mode to change the output parameters.
1
Enter the UPS system setup menu as described in Section 10-7. Use the scroll buttons ( SETUP”, then press the enter button (
2
Use the scroll buttons ( one of the menu choices.
3
From the “VOLTAGE” screen, use the scroll buttons (
, ) to select the desired setting and press the enter button ( )
to confirm the setting.
, ) to move the cursor to “OUTPUT
).
, ) and the enter button ( ) to select
7
8
1
9
10
2
11
37
12
3
13
14
Page 38
10 – Display and Confi guration (continued)
1
10-9 Output Setup Menu (continued)
4
From the “FREQUENCY” screen, use the scroll buttons ( , )
2
to select the desired setting and press the enter button ( confirm the setting. Note: The output frequency setting is only
used when the UPS system starts from battery or when frequency converter mode (see step 6) is enabled.
3
4
From the “ECONOMIC MODE” screen, use the scroll buttons
5
(
, ) to select the desired setting and press the enter button ( ) to confirm the setting.
5
6
6
From the “FREQ CONVERTER MODE” screen, use the scroll buttons ( button (
Note: Press the “ESC” button to return to the previous menu.
, ) to select the desired setting and press the enter
) to confirm the setting.
7
) to
4
5
8
6
10-10 Battery Setup Menu
Note: The UPS system must be in bypass mode to change the battery parameters. The battery parameters must be set correctly in order to receive
9
accurate runtime estimates from the UPS system when it switches to battery backup mode.
1
Enter the UPS system setup menu as described in Use the scroll buttons ( SETUP”, then press the enter button (
, ) to move the cursor to “BATTERY
).
Section 10-7.
10
11
1
Use the scroll buttons (
2
one of the menu choices.
, ) and the enter button ( ) to select
12
13
2
14
38
Page 39
10 – Display and Confi guration (continued)
10-10 Battery Setup Menu (continued)
3
From the “EXT BAT TYPE” screen, use the scroll buttons (
, ) to select the desired settings and press the enter button
(
) to confirm the settings. Note: Possible battery types are
26AH, 40AH, 100AH or 140AH. Possible string settings are 1, 2, 3 or 4.
4
From the “CHARGER CURRENT” screen, use the scroll buttons (
, ) to select the desired setting and press the enter button ( )
to confirm the setting. Note: The default charger current setting is
7A.
1
2
3
3
4
5
From the “BAT DATE SETTING” screen, use the scroll buttons
5
(
, ) to select the desired settings and press the enter button
(
) to confirm the settings.
6
From the “AUTO BAT TEST” screen, use the scroll buttons (
, ) to select the desired setting and press the enter button ( )
to confirm the setting.
Note: Press the “ESC” button to return to the previous menu.
4
6
7
5
8
9
10
6
11
39
12
13
14
Page 40
10 – Display and Confi guration (continued)
1
10-11 Local Setup Menu
Enter the UPS system setup menu as described in Section 10-7.
1
2
Use the scroll buttons ( SETUP”, then press the enter button (
3
4
one of the menu choices.
Use the scroll buttons (
2
5
6
3
From the “DATE/TIME CHANGE” screen, use the scroll buttons (
, ) to select the desired settings and press the enter button (
) to confirm the settings. Note: Changing this setting does not
require an administrator login – a user login is sufficient.
, ) to move the cursor to “LOCAL
).
, ) and the enter button ( ) to select
1
2
10
11
12
13
7
8
4
From the “PASSWORD CHANGE” screen, use the scroll buttons (
, ) and the enter button ( ) to select the desired menu choice. Use the scroll buttons ( and press the enter button (
9
The administrator password should be used by qualified service personnel only.
From the “PARALLEL ID” screen, use the scroll buttons (
5
to select the desired settings and press the enter button ( to confirm the settings. Note: If two UPS systems are used in a
parallel redundancy configuration, the parallel ID numbers of the UPS systems must be 1 and 2.
, ) to select the desired settings
) to confirm the settings. Note:
, )
)
3
4
4b
14
5
40
Page 41
10 – Display and Confi guration (continued)
10-11 Local Setup Menu (continued)
From the “AUDIBLE” screen, use the scroll buttons ( , ) to
6
select the desired settings for the audible alarm and press the enter button (
From the “DISPLAY” screen, use the scroll buttons (
7
select the desired LCD contrast setting and press the enter button (
require an administrator login – a user login is sufficient.
From the “LANGUAGE” screen, use the scroll buttons (
8
to select the desired setting and press the enter button ( confirm the setting. Note: Changing this setting does not require
an administrator login – a user login is sufficient.
) to confirm the setting.
, ) to
) to confirm the setting. Note: Changing this setting does not
, )
) to
1
2
3
6
4
5
7
6
9
From the “SERIAL COM ID” screen, use the scroll buttons (
, ) to select the desired serial port ID and press the enter
button (
apply to standard RS-232 connections. It only applies for RS-485/ RS-422 communications.
Note: Press the “ESC” button to return to the previous menu.
) to confirm the setting. Note: This setting does not
10-12 Maintenance Menu
Press the enter button ( ) to select “MAINTENANCE” from
1
the main menu. Follow the login procedure described in step 2 and step 3 of
2
After the correct password has been entered, the LCD screen will show the maintenance menu. Use the scroll buttons ( enter button (
Section 10-7.
, ) and the
) to select a menu choice.
7
8
8
9
9
10
11
1
12
41
13
2
14
Page 42
10 – Display and Confi guration (continued)
1
10-13 Statistics Menu
Enter the maintenance menu as described in Section 10-12. Use
1
2
the scroll buttons ( press the enter button (
3
4
and the enter button (
If you wish to view statistical data, use the scroll buttons (
2
5
6
3
Available statistical data includes the total operating time, the number of battery events and the number of bypass events.
, ) to move the cursor to “STATISTIC”, then
).
, )
) to select “READ” from the menu.
1
2
7
8
4
If you wish to reset the statistical data, use the scroll buttons (
, ) and the enter button ( ) to select “RESET” from the menu.
9
10
5
You must enter the administrator password to confirm the reset operation.
Note: Press the “ESC” button to return to the previous menu.
11
12
3
4
5
13
14
42
Page 43
10 – Display and Confi guration (continued)
10-14 Event Log Menu
Enter the maintenance menu as described in Section 10-12. Use
1
the scroll buttons ( then press the enter button (
2
If you wish to view the event log, use the scroll buttons ( the enter button (
Use the scroll buttons (
3
Press the “ESC” button to return to the previous menu.
, ) to move the cursor to “EVENT LOG”,
).
, ) and
) to select “READ” from the event log menu.
, ) to scroll through the event log data.
1
2
3
1
4
5
2
6
If you wish to erase the event log, use the scroll buttons (
4
the enter button (
5
You must enter the administrator password to confirm the reset operation.
Note: Press the “ESC” button to return to the previous menu.
) to select “ERASE” from the event log menu.
, ) and
7
3
8
9
4
10
11
5
12
43
13
14
Page 44
10 – Display and Confi guration (continued)
1
10-15 Manual Setup & Test Menu
Enter the maintenance menu as described in Section 10-12. Use
1
2
the scroll buttons ( & TEST”, then press the enter button (
3
2
4
Use the scroll buttons ( menu choice.
5
6
3
Select “FORCE BOOST CHARGE” to boost the battery charge rate. You must enter the administrator password to confirm the operation. Warning: Boosting the battery charge rate for an
extended period may damage the battery system.
, ) to move the cursor to “MANUAL SETUP
).
, ) and the enter button ( ) to select a
1
2
7
8
4
Select “MANUAL BATTERY TEST” to initiate a battery test. You must enter the administrator password to confirm the operation.
9
10
5
Select “BUZZER AND LED TEST” to initiate test of the control panel LEDs and audible alarm. You must enter the administrator password to confirm the operation.
11
12
Select “CLR BAT TEST RESULT” to remove the battery test
6
results from the “MEASURE” menu. (See information.)
13
Note: Press the “ESC” button to return to the previous menu.
3
4
5
Section 10-6 for more
14
6
44
Page 45
10 – Display and Confi guration (continued)
10-16 Firmware Upgrade Menu
Warning: The firmware should be upgraded by qualified service personnel only. Use only firmware that has been approved by Tripp Lite. Failure to comply will void the warranty.
1
Enter the maintenance menu as described in the scroll buttons ( UPGRADE”, then press the enter button (
, ) to move the cursor to “FIRMWARE
Section 10-12. Use
).
1
2
3
Use the scroll buttons (
2
select one of the menu choices. You must enter the administrator password to confirm the operation.
Note: Press the “ESC” button to return to the previous menu.
, ) and the enter button ( ) to
10-17 Other Menu Choices
1
Enter the maintenance menu as described in Section 10-12. Use the scroll buttons ( press the enter button (
2
Use the scroll buttons ( a menu choice. “SN & FW VERSION” shows the serial number and firmware version of the UPS system. “SYSTEM TIME” shows the UPS system’s current date and time. “MODULE DC BUS VOLT” shows the current voltage of the DC bus. Qualified service personnel may wish to view this information when performing maintenance or repair on the UPS system.
Note: Press the “ESC” button to return to the previous menu.
, ) to move the cursor to “OTHERS”, then
).
, ) and the enter button ( ) to select
1
4
5
6
2
7
8
1
9
10
2
11
45
12
13
14
Page 46
11 – Communications
1
Note: The communications connections described in this section are optional. The UPS system will function properly without these connections.
11-1 Communications Interfaces
2
SNMPWEBCARD Slot
3
4
5
Input Dry Contact
Interface
6
Parallel
Redundancy Port
Output Dry
Contact Interface
RS-232
Serial Port
7
11-2 SNMPWEBCARD Slot
Remove the cover panel to install a Tripp Lite SNMPWEBCARD accessory. The SNMPWEBCARD accessory provides an Ethernet interface for
8
the UPS system and enables remote monitoring and control via SNMP, Web browser or telnet. Call (773) 869-1234 for more information about ordering the SNMPWEBCARD accessory.
11-3 Input Dry Contact Interface
9
The input dry contact interface receives contact-closure signals that allow the UPS system to receive commands and monitor external battery conditions:
P1—Remote Emergency Power Off (EPO) P2—Auxiliary Dry Contact Inputs (2 sets)
10
P3—External Battery Cabinet Temperature 1 P4—External Battery Cabinet Temperature 2 P5—External Battery Cabinet Temperature 3
11
P6—External Battery Cabinet Temperature 4 P7—External Battery Status
12
13
14
46
Page 47
11 – Communications (continued)
11-4 Remote Emergency Power Off (EPO) Circuit Diagram
The Remote Emergency Power Off (EPO) input connection (P1) allows you to connect the UPS system to your facility’s EPO circuit. Connecting the UPS system to the EPO circuit enables remote emergency shutdown of the UPS system’s output. Connect EPO input to a user-supplied remote switch, following the circuit diagram below. This contact is normally open.
1
2
P1
11-5 Auxiliary Dry Contact Input Circuit Diagram
The auxiliary dry contact input connections (P2) allow the UPS system to receive external signals. These contacts are normally open.
P2
3
4
5
6
7
8
11-6 External Battery Cabinet Temperature Inputs
The external battery cabinet temperature input connections (P3, P4, P5, P6) allow the UPS system to receive signals from an optional accessory that monitors the temperature of external battery cabinets. Call (773) 869-1234 for more information.
11-7 External Battery Status Input
The external battery cabinet status input connection (P7) allows the UPS system to receive external battery cabinet status signals through an optional cable. Pin 1 = +12V; Pin 2 = detection cable connected; Pin 3 = battery cabinet breaker status (signal active= breaker on; signal inactive = off); Pin 4 = reserved; Pin 5 = reference voltage. Call (773) 869-1234 for more information.
9
10
11
12
13
14
47
Page 48
11 – Communications (continued)
1
11-8 Output Dry Contact Interface Detail
The UPS system has six dry contact output connections. These contacts can be normally open or normally closed.
2
Default Messages
Contact Message Description
Pin 1-2 Load on inverter The UPS system is working normally.
3
Pin 3-4 Load on auto bypass The UPS system is in bypass mode. Pin 5-6 Mains input failure with load on inverter Utility power is absent (blackout) or abnormal. The UPS system is in battery backup mode. Pin 7-8 Battery low The UPS system is in battery backup mode, and battery voltage is lower than 220V. Pin 9-10 Bypass input abnormal The bypass input is abnormal (frequency / phase).
4
Pin 11-12 Battery test failure The battery voltage is lower than the reference value.
Optional Messages
5
Message Description
Internal communication failure Communication with one of the internal components is not normal. External parallel communication failure In a parallel redundancy installation, the parallel communication is not normal. Output overload warning/shutdown The load exceeds the capacity of the UPS system.
6
Power module fault shutdown The UPS system has shut down due to an internal power module failure. Power module warning An internal power module has an error, but the UPS system can still function normally. EPO activated The UPS system’s output is disabled by the emergency power off (EPO) function. Load on manual bypass The UPS system is in manual bypass mode.
7
Battery cabinet over temperature warning/shutdown The temperature of the external battery cabinet is too high. Output voltage abnormal The UPS system’s output voltage is too high or too low. Battery need replace According to the data in the “BAT DATE SETTING”, the UPS system is overdue for battery
replacement. (See
8
Bypass over temperature warning/shutdown The temperature of the bypass “static transfer switch” is too high. Battery ground fault The battery has a grounding error. Bypass static switch fault The bypass “static transfer switch” is abnormal.
9
Note: If you require optional messages to be enabled, contact Tripp Lite.
Section 10-10 for more information.)
10
11
12
13
14
48
Page 49
11 – Communications (continued)
11-9 Output Dry Contact Circuit Diagram
The UPS system has six dry contact output connections. These contacts can be normally open or normally closed.
1
2
3
4
5
6
OUTPUT DRY CONTACT
7
8
9
10
11
49
12
13
14
Page 50
11 – Communications (continued)
1
11-10 RS-232 Serial Port Circuit Diagram
The RS-232 DB9 serial port connects the UPS system to a workstation or server (cable included). By communicating with the UPS system
2
through this port, Tripp Lite’s PowerAlert UPS management software (included) can monitor and control the UPS system. PowerAlert also serves as an SNMP proxy allowing the UPS system to appear as an SNMP-manageable device on the network.
3
RS-232 signals and operations include: load level, battery status, battery level, operation mode, AC input voltage, AC output voltage, AC input frequency, internal temperature, set shut-down delay time, enable/ disable alarm and remote shutdown.
4
Hardware
Baud Rate: 2400 BPS Data Length: 8 bits Stop Bit: 1 bit Parity: NONE
5
Pin Assignment
Pin 2: TXD (Transmit Data) Pin 3: RXD (Receive Data) Pin 5: GND (Signal Ground)
6
11-11 Parallel Redundancy Port
The parallel redundancy port allows the UPS system to be connected to another UPS system of identical type and capacity for use in a parallel redundancy (1+1) configuration for increased capacity or increased fault-tolerance. Warning: Use only the parallel redundancy cable that is
7
included with the UPS system. Attempting to use an incompatible cable may damage the UPS systems and create a serious risk of personal injury and property damage.
10
11
12
13
8
9
14
50
Page 51
12 – Specifi cations
12-1 UPS System Technical Specifi cations
1
Model SU40K SU60K SU60KTV SU80KTV
(Capacity) (40kVA/32kW) (60kVA/48kW) (60kVA/48kW) (80kVA/64kW)
Input Input Voltage 120/208V AC, 3O, 277/480V AC, 3O,
4-wire + ground, wye 4-wire + ground, wye
Voltage Regulation -25% ~ +20%
Harmonic Distortion < 5% (Full Load)
PFC (Full Load) > 0.99
Frequency 50 / 60 Hz
Frequency Tolerance 45 ~ 65 Hz
Output Input Voltage 120/208V AC, 3O, 277/480V AC, 3O,
4-wire + ground, wye 4-wire + ground, wye
Output Frequency 50 / 60 Hz
Total Harmonic (Linear Load) 3%
Voltage Regulation Static ±1%
Frequency Regulation Dynamic ±7% (10% ~ 90% Linear Load)
Interior Oscillator ±0.05 Hz
Synchronized ±5%
Overload ≤125% : 10 minutes; 150% : 1 minute
Audible Warning Battery Backup Intermittent
UPS Abnormal Continuous
Display LED UPS Status: Normal • Bypass • Backup • Fault
LCD Input/Output • Bypass • Inverter • Frequency • Loading • Battery Voltage
UPS abnormal messages with intelligent self-diagnosis.
Interface Standard RS-232, Dry Contact
Optional SNMPWEBCARD
Others Parallel Redundancy Yes (1+1 for 2 UPS systems of the same type and capacity only.)
EPO Standard (Local and Remote)
SRAM Event Log 500 Records
Parameter Configuration Yes
Hot Standby Installation Optional
Battery Temperature Compensation Optional
Battery Cold-Start Standard
Overall Efficiency Normal 92%
ECO 96%
Transfer Time 0 ms
Temperature 32° F ~ 104° F (0° C ~ 40° C)
Humidity (non-condensing) 90%
Noise (1 m) 65 dBA 68 dBA 70 dBA 70 dBA
Dimensions (Power Module) Width 520 mm
Depth 850 mm 950 mm 850 mm
Height 1696 mm
Weight (Power Module) 682 kg* 534 kg 534 kg 584 kg
* With internal batteries.
2
3
4
5
6
7
8
9
10
11
12
12-2 UPS System Floor Loading Table 12-3 Battery Pack Floor Loading Table
Model SU40K SU60K SU60KTV SU80KTV
Weight 682 kg 534 kg 534 kg 584 kg
2
Floor Loading 1543 kg/m
1081 kg/m2 1208 kg/m2 1321 kg/m
2
BP480V26B BP480V40C (40 12V batteries; (40 12V batteries; Model 26AH each) 40AH each)
Weight 470 kg 700 kg
2
Floor Loading 1064 kg/m
51
1575 kg/m
13
2
14
Page 52
13 – Storage and Service
1
Storage
The UPS system must be stored in a clean, secure environment with a temperature less than 40° C (104° F) and a relative humidity less than 90% (non-condensing). Store the UPS system in its original shipping container if possible. If installation occurs more than 6 months after
2
you receive the UPS system, recharge the batteries for at least 24 hours prior to use. Do not rely on the UPS system to provide backup power to connected equipment until the batteries are fully charged. Note: If the UPS system remains off for an extended period of time, it should be
turned on periodically to allow the batteries to recharge. The UPS system should be turned on and the batteries should be recharged at least one uninterrupted 24-hour period every 3 months. Failure to recharge the batteries periodically may cause irreversible battery damage.
3
Service
The UPS system is covered by the limited warranty described in this manual. Site survey service programs, start-up service programs, preventative maintenance service programs and on-site warranty options (2, 3 or 4 years) are also available. For more information, call Tripp Lite Customer Service at (773) 869-1234.
4
14 – Warranty
5
Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 2 years (except U.S., Canada and Mexico: 1 year) from the date of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion. Service under this Warranty includes parts and Tripp Lite service center labor. On-site service plans are available from Tripp Lite through authorized service partners (in most areas). Contact Tripp Lite Customer
6
Service at (773) 869-1234 for details. International customers should contact Tripp Lite support at intlservice@tripplite.com.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).
7
Tripp Lite; 1111 W. 35th Street; Chicago IL 60609; USA
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.
Warranty Registration
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See web site for details.
8
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or model number of the product.
FCC Class A Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
9
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The user must use shielded cables and connectors with this equipment. Any changes or modifications to this equipment not expressly approved by Tripp Lite could void
10
the user’s authority to operate this equipment.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
Made in China.
Note on Labeling
These symbols are used on the label: V~ AC Voltage
V DC Voltage O Phase Ground
11
12
13
14
52
Page 53
Manual del Propietario
1
Sistemas UPS SmartOnline™ Trifásicos
Modelos: SU40K, SU60K, SU60KTV, SU80KTV
Entrada/Salida: 120/208V CA (SU40K, SU60K) o 277/480V CA (SU60KTV, SU80KTV),
50/60 Hz, 3O, 4 hilos + tierra, wye
No es apropiado para aplicaciones móviles.
2
3
4
5
6
7
8
9
10
11
12
13
1111 W. 35th Street, Chicago, IL 60609 USA
+1 773 869 1234 • www.tripplite.com
Derechos de Autor © 2008 Tripp Lite. Todas la marcas registradas son totalmente propiedad de sus respectivos dueños.
53
14
Page 54
Contenido
1
1 Introducción 55
2 Instrucciones de Seguridad Importantes 56
2
3 Características y Funciones 58 del Panel de Control
4 Características y Funciones 59 del Panel Frontal y Trasero
3
5 Instalación del Gabinete 61
5-1 Preparación 61 5-2 Desempaque 61
4
5-3 Colocación 62
6 Conexión de la Batería Interna 63
(Únicamente SU40K)
6-1 Diagramas de Cableado de la Batería Interna 63
5
6-2 Procedimiento de Conexión de la Batería Interna 65
7 Cableado 68
7-1 Advertencias Sobre el Cableado 68 7-2 Preparación del Cableado 68
6
7-3 Diagrama del Bloque de Terminal del Sistema UPS 69 7-4 Diagramas del Cableado del Gabinete de Baterías Externas 69 7-5 Información Eléctrica y Cables 70 7-6 Cableado del Gabinete de Baterías Externas 71
7
7-7 Cableado de Entrada/Salida CA (Un solo UPS) 72 7-8 Cableado de Entrada/Salida CA (UPS en Paralelo –Una Entrada) 73
8 Modos de Operación 74
8
8-1 Modo En Línea (Normal) (Un solo UPS) 74 8-2 Modo en Respaldo (Un solo UPS) 74 8-3 Modo en Derivación Automática (Un solo UPS) 74 8-4 Modo en Derivación Manual (Un solo UPS) 74
9
8-5 Modo En Línea (UPS en Paralelo) 75 8-6 Modo en Respaldo (UPS en Paralelo) 75 8-7 Modo en Derivación Automática (UPS en Paralelo) 75 8-8 Modo en Derivación Manual (UPS en Paralelo) 76
10
9 Arranque, Apagado y Derivación 77
9-1 Diagramas del Panel de Control e Interruptor de Circuitos 77 9-2 Lista de Control Preliminar (Un solo UPS) 77 9-3 Procedimiento de Arranque Normal (Un solo UPS) 77
11
9-4 Procedimiento de Arranque con la Batería (Un solo UPS) 78 9-5 Procedimiento de Derivación Manual (Un solo UPS) 79 9-6 Procedimiento de Apagado (Un solo UPS) 79 9-7 Revisión Preliminar (UPS en Paralelo) 80
12
9-8 Procedimiento de Arranque (UPS en Paralelo) 80 9-9 Procedimiento de Apagado (UPS en Paralelo) 81 9-10 Procedimiento de Derivación Manual (UPS en Paralelo) 82 9-11 Cambiando de Derivación Manual a Normal (UPS en Paralelo) 83
13
10 Pantalla y Confi guración 84
10-1 Diagrama del Panel de Control 84 10-2 Jerarquía de Despliegue 84 10-3 Pantalla Predeterminada 85 10-4 Mensajes de Estado y Diagramas 85 10-5 Menú Principal 87 10-6 Menú de Medidas del Sistema UPS 87 10-7 Menú de Instalación del Sistema UPS 88 10-8 Menú de Instalación de la Derivación 88 10-9 Menú de Instalación de la Salida 89 10-10 Menú de Instalación de la Batería 90 10-11 Menú de Instalación Local 92 10-12 Menú de Mantenimiento 93 10-13 Menú de Estadísticas 94 10-14 Menú de Registro de Eventos 95 10-15 Menú de Instalación Manual y Prueba 96 10-16 Menú para Actualización del Firmware 97 10-17 Menú para Otras Selecciones 97
11 Comunicaciones 98
11-1 Interfaces de Comunicaciones 98 11-2 Ranura SNMPWEBCARD 98 11-3 Interfaz de Entrada de Contacto Seco 98 11-4 Diagrama de Circuito de Apagado de Emergencia Remoto (EPO) 99 11-5 Diagrama de Circuito de Entrada Auxiliar de Contacto Seco 99 11-6 Entradas de Temperatura del Gabinete Baterías Externas 99 11-7 Entrada del Estado de la Batería Externa 99 11-8 Detalle de la Interfaz de Salida de Contacto Seco 100 11-9 Diagrama de Circuito de Salida de Contacto Seco 101 11-10 Diagrama de Circuito del Puerto Serial RS-232 102 11-11 Puerto Paralelo Redundante 102
12 Especifi caciones 103
12-1 Especifi caciones Técnicas del Sistema UPS 103 12-2 Tabla de Carga al Piso del Sistema UPS 103 12-3 Tabla de Carga al Piso del Módulo de Baterías 103
13 Almaceneaje y Servicio 104 14 Garantía 104
English 1 Français 105
14
54
Page 55
1 – Introducción
Los Sistemas UPS SmartOnline Trifásicos de Tripp Lite son ideales para respaldar y proteger centros de datos, telecomunicaciones (VoIP), redes, instalaciones industriales sistemas de seguridad y emergencias y mucho más.
1
Características Avanzadas:
Doble conversión genuinamente en línea con tecnología en el inversor IGBT superior• Corriente de entrada baja de Tasa de Distorsión Armónica (THD) permite la adecuación del tamaño del generador 1:1 para máxima eficiencia y
ahorro en costos Redundancia Interna N+1 del módulo de potencia• Capacidad de redundancia paralela (1+1) incorporada para capacidad incrementada o tolerancia a fallas• Hasta 80kVA de capacidad en una compacta base; hasta 160kVA en configuración de redundancia paralela (1+1)• Factor de potencia de alta entrada y alta eficiencia con baja pérdida termal y bajo ruido• Diseño simplificado, fácil de reparar, larga vida, sistema de alta disponibilidad• Energía auxiliar redundante y circuitos de control• Todos los modelos soportan gabinetes para baterías externas para tiempo de respaldo extendido• Pantalla LCD de alta resolución simplifica la operación y entrega información operacional detallada incluyendo diagramas de bloque del sistema
2
3
4
5
6
7
8
9
10
11
12
13
55
14
Page 56
2 – Instrucciones de Seguridad Importantes
1
CONSERVE ESTAS INSTRUCCIONES
Todas las secciones de este manual contiene instrucciones y advertencias que deberán ser seguidas durante la instalación y operación de los
2
sistemas UPS descritos en este manual. Lea cuidadosamente todas las instrucciones antes de intentar mover, instalar u operar los Sistemas UPS descritos en este manual. El fallar en adherirse a estas instrucciones invalida la garantía y causa daños a la propiedad y/o lesiones personales.
3
Advertencias Sobre la Ubicación del UPS
Instale el sistema UPS en un ambiente controlado al interior, lejos del exceso de humedad, temperaturas extremas, líquidos y gases inflamables, • conductores contaminantes, polvo y luz solar directa.
Instale el sistema UPS en un área nivelada, estructuralmente sólida.
4
El sistema UPS es extremadamente pesado. Extreme las precauciones cuando mueva o levante la unidad.• Opere el UPS únicamente a temperaturas en el interior entre 0º C y 40º C (32º F y 104º F). Para mejores resultados, mantenga la temperatura en
el interior entre 17° C y 29° C (62° F y 84° F). Deje un espacio adecuado alrededor de todos los lados del UPS para una ventilación apropiada. No Obstruya, cubra o inserte objetos en las
5
aberturas de de ventilación externa del gabinete. No coloque ningún objeto sobre la unidad, especialmente los que contengan líquidos.• No monte la unidad con el panel delantero o trasera hacia abajo (en ningún ángulo). Montándolo de esta manera inhibirá seriamente el
enfriamiento interno de la unidad, causando finalmente daño al equipo que no está cubierto por la garantía.
6
No instale el UPS cerca de medios de almacenaje magnéticos ya que esto puede resultar en corrupción de la información. Mantenga todos los • medios con información magnética grabada a una distancia mínima de 60 cm (24 pulgadas) del sistema UPS.
No intente apilar el sistema UPS. Tratar de apilar el sistema UPS puede causar un daño permanente y crea el riesgo de una seria lesión personal.• Las ruedas del sistema UPS están diseñadas únicamente ligeros ajustes dentro del área de instalación final, no están diseñadas para mover al
7
UPS sobre distancias considerables Las ruedas no están diseñadas par brindar un soporte a largo plazo al sistema UPS después de la instalación final. Es necesario instalarlo con los
soportes para montaje. Use los niveladores/puntales para proporcionar un adecuado soporte a largo plazo. Cuando mueva el sistema UPS, empújelo del frente o de atrás, no de los lados.
8
No intente desempacar o mover el sistema UPS sin ayuda.
Advertencias para Conectar el UPS
El suministro de energía eléctrica para esta unidad debe ser trifásica conforme a la placa del nombre del equipo. Debe también estar
9
conectada a tierra apropiadamente de acuerdo a los reglamentos locales de cableado eléctrico.
El sistema UPS contiene alto voltaje peligroso que potencialmente pueden causar lesiones personales o incluso la muerte por descargas • eléctricas.
10
11
12
13
El sistema UPS tiene su propia fuente de energía (batería - interna y/o externa). Las terminales de salida pueden estar vivas aun cuando el UPS • no esté conectado a una fuente de suministro de CA.
Si el sistema UPS recibe energía de de un generador CA operado por un motor, con frecuencia regulada con calidad para computadoras.• El uso de este equipo en aplicaciones de soporte de vida en donde la falla de este equipo pueda hacer suponer que causará la falla del equipo
de soporte de vida o significativamente afectar su seguridad o efectividad no es recomendado. No use este equipo en presencia de una mezcla anestésica inflamable con aire, oxigeno u óxido nitroso.
El sistema UPS esta diseñado para alimentar cargas de computadoras modernas y sus dispositivos periféricos asociados. No use el sistema UPS • para alimentar cargas inductivas puras o capacitivas.
El cableado de entrada y salida debe ser llevado a cabo únicamente por electricistas entrenados y calificados.• Debido a la alta filtración de corriente, una adecuada conexión a tierra es esencial antes de conectar el suministro de corriente CA.• Aísle el sistema UPS antes de trabajar en el circuito. Un dispositivo de desconexión de fácil acceso debe ser incorporado en el cableado
permanente. El dispositivo de desconexión debe ser un dispositivo de 4 polos y debe desconectar a todos los conductores de línea y el conductor neutro.
14
56
Page 57
2 – Instrucciones de Seguridad Importantes
Advertencias Sobre la Batería
El sistema UPS no requiere mantenimiento de rutina. No hay partes útiles para el usuario en el interior. Por la razón que sea únicamente personal • de servicio calificado debe abrir los paneles de acceso.
Las baterías presentan un riesgo de descarga eléctrica y quemaduras derivadas del alta corriente de un corto circuito, las baterías deben ser • remplazadas por personal de servicio capacitado que observe las debidas precauciones. Apague el sistema UPS antes de conectar o desconectar las baterías internas. Use herramientas con asas/mangos aislantes. No abra las baterías. No puentee o haga corto circuito con las terminales de la batería con ningún objeto.
Remplace las baterías por baterías equivalentes disponibles en Tripp Lite. No opere el sistema UPS sin baterías.• Las baterías son reciclables. Refiérase a las regulaciones locales para los requerimientos de disposición y destrucción de las baterías.• No arroje las baterías al fuego, mutile las baterías o abra las tapas de la batería.• Los fusibles de la batería deberán ser remplazados únicamente por personal calificado. Los fusibles quemados deberán ser remplazados
únicamente por fusibles del mismo número y tipo. Existen voltajes potencialmente letales dentro de esta unidad en tanto la suministro de la batería este conectado. El servicio y reparación deberá
ser hecho únicamente por personal capacitado, con el sistema UPS apagado o puesto en modo de derivación. Desconecte las baterías internas (si hubiera alguna) antes de efectuar cualquier servicio apagando el interruptor de circuitos de las baterías internas y quitando el/los fusible(s) de la batería. Desconecte las baterías externas (si hubiera alguna) apagando el interruptor de circuitos del gabinete de baterías externas y desconectando los cables de las baterías externas del sistema UPS.
No conecte o desconecte las baterías cuando el sistema UPS esté operando con el suministro de las bacterias o cuando la unidad no esté en modo • de derivación.
No quite las fundas protectoras de plástico que cubren las baterías internas.• Las baterías internas y externas deben ser remplazadas por baterías equivalentes disponibles de Tripp Lite.• Antes de conectar un gabinete de baterías externas al sistema UPS, lea la documentación del gabinete de baterías externas. Use únicamente
gabinetes para baterías externas que hayan sido aprobadas por Tripp Lite. Si el sistema UPS permanece apagado por periodos prolongados, deberá encenderse periódicamente para permitir que las baterías se recarguen.
El sistema UPS deberá encenderse y recargarse de forma ininterrumpida por un período de 24 horas cada 3 meses. Fallar en recargar las baterías periódicamente puede causar daños irreversibles a las baterías.
1
2
3
4
5
6
7
Advertencias en la Instalación del Cableado Eléctrico
Vea la Sección 7-1 para Advertencias sobre la instalación del cableado eléctrico
8
9
10
11
12
13
57
14
Page 58
3 – Características y Funciones del Panel de Control Panel
1
A E F G H I J KBCD
2
3
4
LED “NORMAL” [En Línea]: Esta luz verde se ilumina para indicar que el sistema UPS está en modo en línea (Normal). La fuente
A
primaria de suministro CA está presente y dentro de los parámetros de operación estándar LED “BATTERY” [Batería]: Esta luz ámbar se ilumina cuando el sistema UPS está en modo de respaldo, descargando las baterías para
B
5
6
7
8
9
10
11
12
suministrar energía al equipo conectado. También sonará una alarma. LED “BYPASS” [Derivación]: Esta luz ámbar se ilumina cuando el sistema UPS está en modo de derivación (derivación automática o
C
derivación manual). No habrá respaldo de la batería disponible al equipo conectado mientras el sistema UPS esté en modo de derivación, pero las cargas del equipo conectado serán soportadas por la fuente de energía de derivación.
LED “FAULT” [Falla]: Esta luz roja se ilumina cuando hay una falla del sistema UPS o de la corriente de entrada. La información de
D
diagnostico disponible se mostrará en la pantalla LCD. Pantalla LCD de Estado: Esta pantalla LCD de Estado iluminada muestra texto y gráficos para indicar un amplio rango de condiciones de
E
operación e información de diagnostico del sistema UPS. Nota: La luz de la pantalla LCD se apagará 10 minutos después de estar inactiva. Encienda la luz momentáneamente presionando el botón ON [Encendido] o cualquiera de los botones de recorrido.
Botón “ESC” (Escape): Presione este botón para regresar a la página o menú anterior.
F
G
Botones de Recorrido (
también sirven para introducir datos en varias pantalla.
Botón Entrar (
H
Botón de Encendido: Presione este botón y manténgalo así por 3 segundos para encender el inversor del Sistema UPS.
I
J
Botón de Apagado: Presione este botón y manténgalo así por 3 segundos para apagar el inversor del Sistema UPS. Si el sistema UPS esta en modo en línea (normal), cambiará a modo de derivación automático. Nota: Si el sistema UPS permanece apagado por periodos prolongados,
deberá encenderse periódicamente para permitir que las baterías se recarguen. El sistema UPS deberá encenderse y las baterías recargarse de forma ininterrumpida por un período de 24 horas cada 3 meses. Fallar en recargar las baterías periódicamente puede causar daños irreversibles a las baterías.
Botón “EPO” (Apagado de Emergencia): Presione este botón para apagar la salida del sistema UPS y también deshabilitar la salida de
K
derivación.
Si el sistema UPS está en modo de respaldo cuando se activa el botón EPO:
La salida principal y la salida de derivación se apagan, la alarma suena, los ventiladores se apagan después de un minuto y los circuitos
de control permanecen activos.
Soltando el botón EPO (presionándolo nuevamente) apaga el sistema UPS completamente, incluyendo la alarma y los circuitos de
control. Presione el botón de encendido por 3 segundos para arrancar nuevamente el sistema UPS.
Si el sistema UPS está en línea (modo normal) cuando se activa el botón EPO:
La salida principal y la salida de derivación se apagan, la alarma suena, los ventiladores y los circuitos de control permanecen activos.• Soltando el botón EPO (presionándolo nuevamente) apaga la alarma y pone al sistema UPS en modo de derivación automática. Presione
el botón de encendido por 3 segundos para regresar el sistema UPS a modo en línea (normal).
Vea la
Sección 10 – Pantalla y Configuración para información detallada acerca del los menús del panel de control y las pantallas.
y ): Presione estos botones para mover el cursor arriba y abajo y navegar los menús y pantallas. Estos botones
): Presione este botón para seleccionar una partida del menú o confirmar una cambio de parámetros.
13
14
58
Page 59
4 – Características y Funciones del Panel Frontal y Trasero
A
B
1
2
3
C
E D
H H
Se muestra el SU40K (frente)
I
4
F
G
5
6
7
8
9
Nota: Los modelos Individuales pueden variar de los diagramas. La unidad se muestra con los biseles frontales removidos.
Panel de Control: El panel de control permite al operador monitorear y controlar el sistema UPS. Vea la
A
funciones del Panel del Control
B
Módulos de Potencia Internos: Los módulos de potencia internos de 20kVA pueden remplazarse en el campo sin apagar las cargas del equipo conectado. La cantidad de módulos de potencia internos varía por modelo. Los módulos internos de potencia son capaces de una redundancia N+1.
C
Compartimiento del Módulo de Batería Internas (SU40K únicamente): las baterías internas deben ser conectadas por un electricista calificado. Vea la
D
Interruptor de Circuitos de Salida (Q4): Controla la salida de energía CA.
E
Interruptor de Circuitos de la Derivación Manual (Q3): Controla la energía CA de entrada al sistema UPS durante una operación de derivación manual.
F
Interruptor de Circuitos de Entrada de Derivación (Q2): Controla la energía CA de entrada al UPS durante una operación de derivación automática.
G
Interruptor de Circuitos Principal de Entrada (Q1): Controla la energía CA de entrada al sistema UPS durante la operación en línea (normal).
H
Niveladores/Puntales: Los niveladores/puntales proporcionan soporte por largo tiempo al sistema UPS.
I
Ruedas: Las ruedas están diseñadas para ajustes de posicionamientos pequeños dentro del área de ubicación final únicamente. No están diseñadas para mover el UPS por largas distancias. Las ruedas no están diseñadas par proporcionar un soporte por largo tiempo al UPS después de la instalación final. Utilice los niveladores/puntales par proporcionar soporte a largo plazo.
Sección 6 – Conexión de la Batería Interna para mayor información.
para mayor información.
59
Sección 3 – Características y
10
11
12
13
14
Page 60
4 – Características y Funciones del Panel Frontal y Trasero (continuación)
1
J
L
2
3
4
M
K N
O
5
P
6
7
8
Nota: Los modelos Individuales pueden variar de los diagramas. La unidad se muestra con los biseles frontales removidos.
9
H
Niveladores/Puntales: Los niveladores/puntales proporcionan soporte por largo tiempo al sistema UPS.
I
Ruedas: Las ruedas están diseñadas para ajustes de posicionamientos pequeños dentro del área de ubicación final únicamente. No están diseñadas para mover el UPS por largas distancias. Las ruedas no están diseñadas par proporcionar un soporte por largo tiempo al UPS
10
11
12
13
14
después de la instalación final. Utilice los niveladores/puntales par proporcionar soporte a largo plazo.
J
Ranura para Accesorios: Remueva la tapa para instalar un accesorio SNMPWEBCARD de Tripp Lite. El accesorio SNMPWEBCARD proporciona una interfaz Ethernet para el sistema UPS y permite el monitoreo y control remoto vía SNMP, navegador de Web o telnet. Llame al +1 773 869 1234 para mayor información acerca del accesorio SNMPWEBCARD.
K
Puerto de Comunicaciones Seriales RS-232: Este puerto DB9 conecta al sistema UPS a una estación de trabajo o servidor compatibles, permitiendo automáticamente apagar el equipo durante apagones prolongados y monitorear las operaciones y las condiciones de la energía.
L
Puerto de Redundancia Paralela: Este puerto DB9 conecta al sistema UPS a otro sistema UPS de tipo y capacidad idénticos para usarse en una configuración de redundancia paralela (1+1). Vea la información.
Interfaz de Entrada de Contacto Seco: Esta interfaz recibe señales de contacto seco que permiten al sistema UPS recibir ordenes y
M
monitorear las condiciones de la batería externas. Vea la Interfaz de Salida de Contacto Seco: Esta interfaz permite al sistema UPS enviar información vía de comunicaciones de contacto seco. Vea
N
la
Sección 11 – Comunicaciones para mayor información.
Interruptor de Circuitos de las Baterías Internas (SU40K únicamente): Controla la energía de entrada/salida de las baterías internas del
O
sistema UPS.
P
Tapa del Bloque de Terminales: Remueva la tapa del bloque de terminales para acceder a las terminales de conexión de entrada, gabinete de baterías externas, salida y tierra del sistema UPS. Conduits cableados pasan a través de las perforaciones circulares [knockouts] en la tapa de terminales del bloque de terminales. Vea la terminales.
H
Se muestra el SU40K (parte posterior)
Sección 7 – Cableado y la Sección 8 - Modos de Operación para mayor
Sección 11 – Comunicaciones para mayor información.
Sección 7 – Cableado para mayor información, incluyendo un diagrama detallado del bloque de
60
I
H
Page 61
5 – Instalación del Gabinete
Lea la Sección 2 – Instrucciones de Seguridad Importantes
Antes de la Instalación
5-1 Preparación
El sistema UPS debe instalarse en un área estructuralmente sólida en un piso nivelado que sea capaz de soportar el peso de del sistema UPS, el gabinete de baterías externas y otro equipo que vaya a ser instalado cerca. El sitio de la instalación debe contar con un circuito CA dedicado que sea compatible con los requerimientos de entrad del sistema UPS. (Vea la entrada y de la carga del piso) Antes de desempacar la unidad, debe llevar el contenedor de embarque cerca del lugar de la instalación final para minimizar la distancia que necesitará mover a unidad después de que el contenedor de embarque haya sido removido. Si planea almacenar el sistema UPS por un período prolongado antes de instalarlo, siga las instrucciones en la desempaque y almacenaje también están impresas en la hoja “Unpacking and Storage Instructions” [Instrucciones de desempaque y almacenaje] pegadas al contenedor de embarque) Advertencia: No intente desempacar o mover el sistema UPS sin ayuda.
Sección 12 – Especificaciones para los detalles de requerimientos de
Sección 13 – Almacenaje y Servicio. (Instrucciones de
1
2
3
4
5-2 Desempaque
1-2
Inspeccione el contendor de embarque por daños visibles. Si determina que la unidad ha siso dañada durante el embarque, comuníquese con Tripp Lite por asistencia. No intente usar el sistema UPS si ha sido dañado o manejado inadecuadamente.
Confirme que contenedor de embarque está hacía arriba y use un desatornillador para quitar el panel superior, panel frontal y panel trasero. También quite el plástico y el material de acojinamiento interior. Confirme que el nombre del modelo y tipo indicado en la parta posterior del gabinete sea el mismo del que usted ordenó. Examine gabinete en busca de cualquier daño o partes sueltas. Confirme que el contendor de embarque incluye los accesorios que se deben embarcar con la unidad. El sistema UPS debe incluir un cable serial RS-232, un cable de redundancia en paralelo, un conector para EPO remoto, un conector de entrada de contacto seco (4 contactos), un conector de salida de contacto seco (12 contactos) y un CD-ROM con el software. Si algo falta o está dañado comuníquese con Tripp Lite por asistencia.
Confirme que la unidad está estable, y entonces remueva los paneles laterales del contenedor de embarque.
5
6
7
1
8
9
10
3
Remueva los tornillos de la s abrazaderas de embarque que aseguran la unidad a la tarima y a continuación remueva las abrazaderas del sistema UPS. Advertencia:
Extreme precauciones ya que la unidad podría voltearse inesperadamente.
Use varios de los tornillos que quitó en el paso 1 para fijar el panel superior del contenedor de embarque a la orilla frontal de la tarima de embarque. La superficie suave del panel debe estar hacia arriba de tal forma que puede ser usada como rampa para rodar la unidad de la tarima de embarque. No intente usar el panel superior como rampa si se encuentra rajada o dañada estructuralmente en cualquier forma. Asegúrese de que las ruedas debajo de la unidad no están aseguradas. Extreme precauciones y con la ayuda de varios asistentes, lentamente ruede la unidad rampa abajo.
61
2
11
12
13
3
14
Page 62
5 – Instalación del Gabinete (continuación)
1
5-3 Colocación
Use las ruedas para mover el sistema UPS por cortas distancias
1
2
3
4
5
6
7
8
9
sobre una superficie nivelada, suave y estable. No intente usar las ruedas para mover el sistema UPS por largas distancias. El sistema UPS deberá moverse cerca del sitio de ubicación final dentro de su contenedor de embarque antes de desempacarlo del contenedor de embarque. Use un dispositivo mecánico de la suficiente capacidad para mover el contenedor de embarque. Advertencia: El sistema
UPS puede volcarse si es movido en un área inestable. Extreme precauciones cuando mueva el sistema UPS. Empuje el sistema UPS del frente o de atrás, y no de los lados.
2
Posicione el sistema en un área estructuralmente sólida con un piso nivelado que sea capaz de soporta el peso del sistema UPS los gabinetes de baterías externas y otros equipos que vayan a ser instalados cerca. La instalación también deberá contar con un circuito CA dedicado que sea compatible con los requerimientos de entrada del sistema UPS. (Vea la the para más información acerca de los requerimientos de entrada y los requerimientos de rssitencia/carga del piso). El sistema UPS debe instalarse en un entorno limpio, seguro con una humedad relativa menor al 90% (sin condensación). Opere el sistema UPS a temperaturas interiores entre 17° C y 29° C (62° F y 84° F). Prevenga daños al cableado utilizando conduits protectores adecuados. A fin de mantener un adecuado flujo de aire y acceso para servicio, debe mantener el siguiente espacio libre:
Por lo menos 100 cm de espacio libre al frente del
sistema UPS.
Por lo menos 50 cm de espacio libre atrás del sistema UPS.• Por lo menos 50 cm de espacio libre arriba del sistema UPS.
Advertencia: El ventilador de enfriamiento circula el aire del frente hacia atrás. No utilice ningún aire acondicionado o ventilador que dirija el aire directamente hacia la parte de atrás del sistema UPS.
Después de mover el sistema UPS a su ubicación final, asegure
3
las ruedas Asegúrese que los cuatro niveladores hacen un contacto firme con el suelo.
A
y use los niveladoresBpara estabilizar el gabinete.
Sección 12 - Especificaciones
1
50 cm
50 cm
100 cm
2
10
11
12
13
14
Para casos de emergencia, instale cerca del sistema UPS
4
un extintor certificado para incendios de equipos eléctricos (Certificado Clase C o su equivalente exacto con un agente extintor no conductivo).
62
A
3
4
B
Page 63
6 – Conexion de la Batería Interna (Únicamente Modelo SU40K)
¡PELIGRO! ¡RIESGO DE ALTO VOLTAJE LETAL!
Alto voltaje potencialmente letal existe dentro de las baterías, aun y cuando no estén conectadas al sistema UPS. Las conexiones de la batería deberán ser efectuadas únicamente por personal de servicio califi cado, siguiendo todas las precauciones indicadas en este manual y adherirse a todos los códigos eléctricos locales. Antes de proceder lea la
2 – Instrucciones de Seguridad Importantes
.
1
2
Sección
Las conexiones para la batería interna son únicamente para el modelo SU40K. Cada módulo de baterías externas consiste de dos cadenas de baterías: una cadena con un cable negro y otra cadena con un cable rojo.
6-1 Diagramas de Cableado de la Batería Interna
Revise los diagramas del cableado de la batería interna antes de conectar las baterías internas. El sistema UPS puede aceptar hasta cuatro módulos de baterías internas (cada módulo consiste de dos cadenas, cada cadena consiste de 10 baterías). El número de baterías internas varía por modelo.
Q3
XFMR XF MR
ENTRADA DE DERIVACIÓN SALIDACA/CD
B+ N B-
Q1Q2
AC/DCMAIN I NPUT
CD/CA
UPS
B+ N B-
12V, 20PCS 12V, 20PCS
12V, 20PCS 12V, 20PCS
Se muestra el SU40K
Q4
OUTP UTDC/AC
3
4
5
6
7
8
VBoard
B+
N
VBoard
B-
W1: ROJO, W2: AZUL, W3: BLANCO, W4: NEGRO
W1: RED, W2: BLUE, W3: WHITE, W4: BLACK
ROJO ROJO
RED RED
NEGRO NEGRO
BLACK BLACK
ROJO ROJO
RED RED
NEGRO NEGRO
BLACK BLACK
ROJO ROJO
RED RED
NEGRO NEGRO
BLACK BLACK
ROJO ROJO
RED RED
NEGRO NEGRO
BLACK BLACK
Se muestra el SU40K
12V, 9AH, 10PCS
W1
12V, 9AH, 10PCS
W1
12V, 9AH, 10PCS
W1
12V, 9AH, 10PCS
W1
W2
W2
W2
W2
W3
W3
W3
W3
12V, 9AH, 10PCS
12V, 9AH, 10PCS
12V, 9AH, 10PCS
12V, 9AH, 10PCS
W4
W4
W4
W4
9
10
11
12
13
14
63
Page 64
6 – Conexion de la Batería Interna (continuación)
1
6-1 Diagrama de Cableado de la Batería Interna (continuación)
2
3
4
5
6
10
11
12
Conector
UPS System
Trasero de la
Battery Back
7
AZUL
Batería
8
Superior
BLANCO
BLANCO
Batería Inferior
AZUL
9
Batería del
Connector
Sistema UPS
BLANCO
Batería
Inferior
AZUL
Conector
UPS System
Trasero de la Batería del
Battery Back
Sistema UPS
Connector
AZUL
Batería Superior
BLANCO
Soporte del Bloque
Fuse Block Bracket
de Fusibles
13
14
Se muestra el SU40K
64
Page 65
6 – Conexion de la Batería Interna (continuación)
6-2 Procedimiento para la Conexión de la Batería Interna
Coloque el sistema UPS en derivación (o apáguelo completamente)
1
y apague el interruptor de circuitos de la batería interna, localizado en la parte trasera del sistema UPS.
1
2
3
Remueva los biseles de acceso a la batería, localizados al frente del
2
sistema UPS.
3
Remueva los cartuchos de fusibles de cada bloque de fusibles.
4
Desconecte los cables de puenteo [jumpers] azul y blanco conectado a cada bloque de fusibles. Advertencia: Cuando
desconecte los cables de puenteo, jálelos hacia fuera del bloque de fusibles con una fuerza uniforme. No los menee de lado a lado, ya que esto puede dañar al conector.
1
4
5
6
2
7
8
3
9
10
5
Remueva el soporte de los fusibles. Observe su orientación antes de removerlos.
11
4
12
13
5
14
65
Page 66
6 – Conexion de la Batería Interna (continuación)
1
6-2 Procedimiento para la Conexión de la Batería Interna (continuación)
Deslice una cadena de baterías con un cable rojo en una ranura
6
2
vacía dentro del compartimiento de baterías. Asegúrese que la cadena de baterías está orientada como se muestra en el diagrama.
Nota: Empiece con las ranuras vacías de hasta abajo del compartimiento y trabaje hacia las ranuras vacías de la parte superior del compartimiento de la batería.
3
4
7
Deslice una cadena de baterías con un cable negro en una ranura
5
vacía dentro del compartimiento de baterías, junto a la cadena de baterías que insertó en el paso 6. Asegúrese que la cadena de baterías está orientada como se muestra en el diagrama. Repita los pasos 6 y 7 conforme se necesite hasta que todas las cadenas de baterías hayan sido insertadas en las ranuras vacías.
6
TERMINALES
VISTA LATERAL
6
TERMINALES
VISTA LATERAL
10
11
12
13
7
7
Reconecte el soporte del bloque de fusibles. (Las letras en
8
el bloque de fusibles deberán estar hacia arriba cuando están
8
orientadas correctamente.)
9
8
9
Conecte los cables de puenteo azul y blanco en cada módulo de baterías internas al bloque de fusibles correspondientes. La rotulación junto al bloque de fusibles identifica el bloque de fusibles correcto para cada cable.
9
Inserte el cartucho de fusibles en cada bloque de fusibles. Los
10
fusibles son intercambiables. Asegúrese que estén firmemente insertados en su lugar. Advertencia: Los cartuchos de fusibles
de la batería deben insertarse al último debido a la posibilidad de arcos voltaicos entre los conectores. Los fusibles quemados deben ser remplazados por un electricista calificado. Remplace los fusibles únicamente por fusibles del mismo tipo y número.
14
10
66
Page 67
6 – Conexion de la Batería Interna (continuación)
6-2 Procedimiento para la Conexión de la Batería Interna (continuación)
11
Use un voltímetro (suministrado por el usuario) para probar el voltaje de cada módulo de baterías internas. Observando la polaridad correcta conecte el sensor negro del voltímetro al conector negro del módulo de baterías; conecte el sensor voltímetro al conector los sensores del voltímetro toquen los contactos metálicos dentro de los conectores del módulo de baterías. El rango de voltaje CD aceptable está entre 220V y 280V CD (240V CD nominales). Si varias pruebas con el voltímetro arrojan resultados fuera del rango CD aceptable, comuníquese con Tripp Lite por asistencia para determinar las posibles causas las lecturas incorrectas de voltaje antes de proceder.
12
Conecte el cable negro por cada módulo de baterías internas al conector negro más cercano localizado dentro del compartimiento de baterías del sistema UPS. Conecte el cable módulo de baterías internas al conector localizado dentro del compartimiento de baterías del sistema UPS. Advertencia: Observe la polaridad correcta conectando
negativo con negativo (negro con negro) y positivo con positivo (
rojo con rojo). Fallar en observar la polaridad correcta
dañará el sistema UPS y creará un serio riesgo de lesiones personales y daños al a propiedad.
rojo del módulo de baterías. Asegúrese que
rojo por cada
rojo más cercano
rojo del
240
11
12
1
2
3
4
5
6
13
Vuelva a colocar los biseles de acceso a la batería.
14
Encienda el interruptor de circuitos de las baterías internas. Si puso el sistema UPS en derivación, regréselo al modo de operación anterior. Si apagó el sistema UPS enciéndalo. Si aún necesita cablear el sistema UPS, proceda a la
Nota: Si necesita remover o remplazar las baterías internas, modifique los pasos 6 y 7 removiendo y/o remplazando los módulos de baterías internas existentes conforme se requiera.
Sección 7 – Cableado.
13
14
7
8
9
10
11
12
67
13
14
Page 68
7 – Cableado
1
¡PELIGRO! ¡RIESGO DE ALTO VOLTAJE LETAL!
2
3
7-1 Advertencias sobre el Cableado
Desconecte todas la fuentes de energía de entrada y salida del sistema UPS antes de instalar los cables o hacer conexiones eléctricas.• Use cables flexibles de longitud suficiente que permitan dar servicio al sistema UPS. La longitud máxima del cable es 10 m (32.8 pies).• Use conteras/virolas para cubrir las terminaciones de los cables y evitar terminaciones deshilachadas que puedan hacer corto con el bloque de
4
terminales del sistema UPS. Use cables VW-1, FT-1 o mejores.• Use fundas para cables y abrazaderas para los conectores.
5
Los conductores neutros deben ser del mismo calibre que los conductores de corriente.• Apriete todas las conexiones con una fuerza de torsión de por lo menos 3.95 N·m (35 in·lb)• Confirme que los cables están marcados correctamente de acuerdo a su propósito, polaridad, fase y diámetro.• Si la fuente de energía de entrada /salida es wye-wye, entonces “Neutro” y “Tierra” no deben ser conectados.
6
Si la fuente de energía de entrada tiene VNG>0, instale un transformador de aislamiento antes del sistema UPS y la fuente de energía de entrada, • y entonces conecte el “neutro” y “Tierra” del sistema UPS juntos.
Para equipos que requieran una conexión neutra a un sistema de distribución de energía IT, el dispositivo de desconexión debe ser un dispositivo • de cuatro polos y debe desconectar todos los conductores de línea y el conductor neutro. Si un dispositivo de desconexión interrumpe al
7
conductor neutro, debe simultáneamente interrumpir todos los conductores de línea. Permita que las baterías se carguen ininterrumpidamente durante 24 horas después de la conexión inicial de cableado.• Observe la polaridad correcta conectando negativo con negativo y positivo con positivo. Fallar en observar la polaridad correcta dañará al
sistema UPS y crea un serio riesgo de lesiones personales y daños a la propiedad.
8
Observe la fase adecuada conectando R con R, S con S, T con T y N con N. Fallar en observar la polaridad correcta dañará al sistema UPS y • crea un serio riesgo de lesiones personales y daños a la propiedad.
Todo el cableado deberá ser llevado a cabo por un electricista califi cado, conforme a todas las advertencias de este manual y todos los códigos de electricidad y seguridad aplicables. Un cableado incorrecto puede dañar al sistema UPS y causar serias lesiones personales y daños a la propiedad. Antes de proceder lea la
Importantes
.
Sección 2 – Instrucciones de Seguridad
7-2 Preparación del Cableado
9
Desconecte todas la fuentes de energía de entrada y salida (CA y CC) del sistema UPS y del gabinete de baterías externas (Si lo hubiera).• Marque correctamente de acuerdo a su propósito, polaridad, fase y diámetro.
10
Revise los diagramas en la • Consulte la tabla en la
Nota: Si la fuente de energía de entrada/salida del sistema UPS es wye-wye, entonces el “Neutro” y “Tierra” no deben conectarse. Si la fuente de energía de entrada tiene VNG>0, instale un transformador de aislamiento antes del sistema UPS y la fuente de energía de entrada y entonces conecte el “Neutro y la “Tierra” del sistema UPS juntos.
Sección 7-3 y la Sección 7-4 para familiarizarse con el bloque de terminales.
Sección 7-5 para encontrar las características eléctricas de entrada/salida correctas para el sistema UPS.
11
12
13
14
68
Page 69
7 – Cableado (continuación)
N
7-3 Diagrama del Bloque de Terminales del Sistema UPS
1
2
Entrada
RRSSTTN
Terminales de Tierra
Conexión de la
Batería Externa
N+
7-4 Diagramas del Cableado del Gabinete de Baterías Externas
Salida
3
N
4
5
6
7
+N–
Interruptor de
Circuitos del Gabinete
de Baterías Externas
8
9
+
10
11
12
13
Se muestran el SU40K y el BP480V40C únicamente como ilustración; consulte la documentación del gabinete de baterías para las
especificaciones exactas
69
14
Page 70
7 – Cableado (continuación)
T
1
7-4 Diagramas del Cableado del Gabinete de Baterías Externas (continuación)
2
3
XFMR XFMR
ENTRADA
PRINCIPAL
4
UPS
5
B+ N B-
6
GABINETE DE BATERÍAS EXTERNAS
External Battery Cabinet B Cabinet: 26AH per Battery
GABINETE B: 26AH PARA CADA BATERÍA
C Cabinet: 40AH per Battery
GABINETE C: 40AH PARA CADA BATERÍA
7
7-5 Información Eléctrica y Cables
Q1Q2
12V, 20 Batteries 12V, 20 Batteries
CA/CD
AC/DCMAIN INPUT
B+ B-N
BATERÍAS BATERÍAS
CD/CA
DC/AC
Q3
Q4
SALIDA
OUTPU
Capacidad de Salida/Entrada del Capacidad del Calibre del Cable Calibre del Cable Modelo Entrada/Salida Interruptor de Circuitos Fusible de la Batería de Entrada/Salida de la Batería
8
SU40K 120/208V AC, 3O, 150A 120A 1/0 AWG 6 AWG 4 hilos + tierra, wye
SU60K 120/208V AC, 3O, 225A 160A 4/0 AWG 4 AWG 4 hilos + tierra, wye
9
SU60KTV 277/480V AC, 3O, 100A 160A 4 AWG 4 AWG 4 hilos + tierra, wye
SU80KTV 277/480V AC, 3O, 125A 220A 2 AWG 2 AWG 4 hilos + tierra, wye
10
11
12
13
14
70
Page 71
7 – Cableado (continuación)
N
7-6 Cableado del Gabinete de Baterías Externas
Advertencia: los gabinetes de baterías externas varían. Lea la documentación del gabinete de baterías externas antes de tratar de conectarlo al sistema UPS. Use únicamente gabinetes de baterías externas que estén aprobados por Tripp Lite.
Nota: Se requiere un gabinete de baterías externas los modelos SU60K, SU60KTV y SU80KTV. Es opcional con el modelo SU40K. Contacte a Tripp Lite por información para ordenar los gabinetes de baterías externas.
Desconecte todas las entradas y salidas (CA y CD) del sistema
1
UPS y del gabinete de baterías externas y confirme que el interruptor de circuitos sido cableado a una fuente de energía CA, vea la, instrucciones de apagado.)
2
Remueva las tapas del bloque de terminales del sistema UPS y del gabinete de baterías externas.
A
esté apagado. (Si el sistema UPS ya ha
Sección 9-6 para
A
1
1
2
3
4
5
Conecte las terminales de conexión del sistema UPS del gabinete
3
de baterías externas positivo (+), neutro (N) y negativo (-) a las terminales correspondientes positivo (+), neutro (N) y negativo (-) de las terminales de conexión de las baterías externas del sistema UPS. Vea la baterías externas para diagramas del bloque de terminales. Vea la
Sección 7-4 para los diagramas de conexión. Vea la Sección 7-5
para los requerimientos del calibre de los cables. Los cables de estar protegidos por conduits flexibles y enrutados a través de las perforaciones circulares [knockouts] correspondientes en la tapa del bloque de terminales. Advertencia: Observe la polaridad
correcta conectando negativo con negativo y positivo con positivo. Fallar en observar la polaridad correcta dañará al sistema UPS y crea un riesgo de lesiones personales y daños a la propiedad.
Conecte la terminal de tierra del gabinete de baterías externas
4
a la terminal de tierra correspondiente del sistema UPSBcon un cable de tierra 4 AWG (5.189 mm). Mantenga siempre conectado el cable de tierra después de la instalación.
5
Conecte la terminal de tierra de sus instalaciones Mantenga siempre conectado el cable de tierra después de la instalación.
Vuelva a colocar la tapa del bloque de terminales del gabinete de
6
baterías externas. Si no tiene planes de de cablear la entrada/salida CA del sistema UPS en este momento, vuelva a colocar la tapa del bloque de terminles del sistema UPS.
Sección 7-3 y la documentación del gabinete de
A
del sistema UPS a la tierra física
B
con un cable de tierra 4 AWG (5.189 mm).
6
2
+N–
+N–
7
8
9
A
3
10
A
B
4
11
12
B
A
65
71
13
14
Page 72
7 – Cableado (continuación)
N
N
1
7-7 Cableado de la Entrada/Salida CA (Un Solo UPS)
Después de desactivar todas las entradas y salidas (CA y CD) del
1
2
3
sistema UPS, quite la tapa del bloque de terminales del sistema UPS.
10
11
4
Si no conectó el cable de tierra en la
2
A
terminal de tierra instalaciones con un cable de tierra 4 AWG (5.189 mm). Mantenga siempre conectado el cable de tierra después de la instalación.
del sistema UPS a la tierra físicaBde sus
Sección 7-6, conecte la
1
5
B
6
3
Remueva el bisel frontal del sistema UPS para dejar descubiertos los interruptores de circuitos. Primero, confirme que tanto el interruptor de circuitos de la entrada principal
7
interruptor de circuitos de la entrada de derivación apagados. Segundo, confirme que el interruptor del interruptor de circuito de derivación manual que el interruptor de circuitos de salida
C
esté apagado. Tercero, confirme
D
A
como el
B
esté apagado.
estén
2
D B AC
A
8
3
4
Confirme la fase de cada cable, entonces conecte los cables de
9
acuerdo al diagrama de bloque de terminales del sistema UPS en la
Sección 7-3. Vea la Sección 7-5 para los requerimientos del
calibre del cable. El cableado deberá estar protegidos por conduits flexibles y enrutados a través de las perforaciones circulares [knockouts] adecuadas en el bloque de terminales Advertencia:
Observe las fases correctas conectando R con R, S con S, T con T y N con N. Fallar en observar la fase correcta dañará al sistema UPS y crea un riesgo de lesiones personales y daños a la propiedad.
5
Vuelva a colocar la tapa del bloque de terminales del sistema the UPS.
R S T
4
+N
R S T
12
13
14
5
72
Page 73
7 – Cableado (continuación)
7-8 Cableado de la Entrada/Salida CA (UPS en Paralelo – Una Entrada)
Advertencias de la Redundancia en Paralelo:
La longitud total del cable de entrada debe ser igual • a la longitud total del cable de salida a fin de prevenir la distribución desequilibrada de la carga entre los dos sistemas UPS en modo de reserva (i.e. IP1 + OP1 = IP2 + OP2; la desviación debe ser <10%).
La redundancia en paralelo solo soporta 2 sistemas UPS • (redundancia 1+1 ). No trate de conectar más de dos sistemas UPS vía redundancia en paralelo.
El sistema UPS debe tener la misma clasificación y • capacidad para una instalación de redundancia en paralelo. El tratar de conectar sistemas UPS que no sean similares dañará los sistemas UPS y crea un serio riesgo de lesiones personales y daños a la propiedad.
Siga los pasos en la
1
como se muestra en el diagrama.
Sección 7-7, Cableando los sistemas UPS,
1
AC I/P
IP1
IP2
l/P Principal
Main I/P
l/P Principal
Main I/P
UPS1
UPS2
O/P
Puerto Paralelo
Parallel Port
O/P
Puerto Paralelo
Parallel Port
OP1
CABLE PARALELO
Parallel Cable
OP2
Carga
Load
1
2
3
4
5
Conecte el cable, incluido, de redundancia en paralelo
2
de redundancia en paralelo
B
de cada sistema UPS.
A
al puerto
B
B
A
6
7
2
8
9
10
11
73
12
13
14
Page 74
8 – Modos de Operación
1
Esta sección proporciona una descripción básica de los modos de operación del sistema UPS. Para una mayor información sobre como cambiar de modos de operación, refiérase a la
2
8-1 Modo En Línea (Normal) (Un Solo UPS)
En modo en línea (normal), el rectificador del sistema UPS convierte la energía CA entrante del servicio público a energía CD que carga las baterías y alimenta al inversor. El inversor transforma la energía CD en
3
energía CA de precisión regulada y de onda sinusoidal pura que soporta la operación del equipo conectado. Esta tecnología de doble conversión aísla al equipo conectado de todos los problemas de energía y asegura que el equipo conectado la energía ideal todo el tiempo.
4
8-2 Modo de Respaldo (Un Solo UPS)
5
Cuando ocurre un apagón o cualquier otro problema de energía extremo, el sistema UPS automáticamente cambia de modo normal a modo de respaldo. Las baterías del sistema UPS (internas y/o externas) suministran energía CD de emergencia al inversor. El inversor convierte la energía CD en energía CA de precisión regulada y de onda sinusoidal
6
pura que respalda la operación del equipo conectado.
Sección 9 – Arranque, Apagado y Derivación.
MAIN
PRINCIPAL
MAIN
PRINCIPAL
CB3
CB2
CB3
CB2
CB1
XFMR XFMR
CB1
XFMR XFMR
CB5
CB5
STS
STS
CB4
LOAD
CARGA
CB4
LOAD
CARGA
7
8-3 Modo de Derivación Automática (Un Solo UPS)
Si el inversor funciona mal debido a temperatura excesiva, sobrecarga, corto circuito de salida, voltaje anormal o problemas con la batería, el
8
inversor se apagará. Si el sistema UPS detecta una fuente de energía derivada que se ajuste a los parámetros normales, el sistema UPS automáticamente cambiara a modo de derivación automática para continuar alimentando de energía al equipo conectado. Cuando todos los problemas hayan sido eliminados, el sistema UPS regresa al modo
9
en línea (normal) automáticamente.
10
8-4 Modo de Derivación Manual (Un Solo UPS)
Si se requiere dar mantenimiento o reparar al sistema UPS, puede derivar el sistema UPS manualmente. Después de confirmar que hay energía de derivación presente, cambie el sistema UPS a a modo de
11
derivación manual. Esto permite a los técnicos de servicio efectuar los trabajos de mantenimiento o reparación sin interrumpir el flujo de de energía CA al equipo conectado. Advertencia: El sistema UPS
debe desactivarse completamente antes de efectuar cualquier mantenimiento o reparación apagándola completamente después de
12
cambiar a modo de derivación manual.
MAIN
PRINCIPAL
MAIN
PRINCIPAL
CB3
CB2
CB3
CB2
CB1
XFMR XFMR
CB1
XFMR XFMR
CB5
CB5
STS
STS
CB4
LOAD
CARGA
CB4
LOAD
CARGA
13
14
74
Page 75
8 – Modos de Operación (continuación)
8-5 Modo En Línea (UPS en Paralelo)
La redundancia en paralelo (1+1) proporciona redundancia del sistema UPS o un incremento en su capacidad total. Bajo redundancia en paralelo, la carga total es compartida por los dos sistemas UPS. Si uno de los sistemas UPS falla, la carga total de los equipos conectados es soportada por el sistema UPS que queda. Si la carga total excede la capacidad del sistema UPS que queda, cambiará a modo de derivación automático.
PRINCIPAL
MAIN
CB3
CB2
CB3
CB1
XFMR XFMR
CB5
STS
CB4
UPS1
LOAD
CARGA
1
2
3
4
8-6 Modo de Respaldo (UPS en Paralelo)
Es similar al Modo de Respaldo para un solo sistema UPS (Sección
8-2
), excepto que la carga total del equipo conectado es compartida por
los sistemas UPS en paralelo (1+1).
PRINCIPAL
MAIN
PRINCIPAL
MAIN
PRINCIPAL
MAIN
CB2
CB3
CB2
CB3
CB2
CB1
XFMR XFMR
CB1
XFMR XFMR
CB1
XFMR XFMR
CB5
CB5
CB5
STS
STS
STS
CB4
UPS2
CB4
UPS1
CB4
UPS2
LOAD
CARGA
5
6
7
8
9
8-7 Modo de Derivación Automática (UPS en Paralelo)
Es similar al Modo de Derivación Automática para un solo sistema UPS (
Sección 8-3), excepto que con sistemas UPS en paralelo (1+1).
75
RESERVA
PRINCIPAL
RESERVA
PRINCIPAL
10
11
12
CARGA
13
14
Page 76
8 – Modos de Operación (continuación)
1
8-8 Modo de Derivación Manual (UPS en Paralelo)
Es similar al Modo de Derivación Manual para un solo sistema UPS
Sección 8-4), excepto que con sistemas UPS en paralelo (1+1). Nota:
(
2
Ambos sistemas UPS deben estar en Modo de Derivación Manual.
CB3
CB2
PRINCIPAL
MAIN
3
CB3
CB1
XFMR XFMR
CB5
STS
CB4
UPS1
LOAD
CARGA
4
PRINCIPAL
MAIN
CB2
CB1
XFMR XFMR
CB5
STS
5
CB4
UPS2
6
7
8
10
11
12
13
14
9
76
Page 77
9 – Arranque, Apagado y Derivación
9-1 Diagramas del Panel de Control e Interruptor de Circuitos
A
LED “NORMAL” [En Línea]
B
LED “BATTERY” [Batería]
C
LED “BYPASS” [Derivación]
D
LED “FAULT” [Falla] Pantalla LCD de Estado
E F
Botón “ESC” (Escape)
G
Botones de Recorrido (
H
Botón Entrar (
I
Botón de Encendido Botón de Apagado
J K
Botón “EPO” (Apagado de Emergencia)
L
Interruptor de Circuitos de Salida
M
Interruptor de Circuitos de Derivación Manual
N
Interruptor de Circuitos de Entrada de Derivación
O
Interruptor de Circuitos de la Entrada Principal
y )
)
E
A
B
C
D
F
I
G
J
H
Panel de Control
L
Salida
M
Derivación
Manual
N
Entrada de Derivación
O
Entrada
Principal
Interruptores de los Interruptores de Circuito
(Panel Frontal del Sistema UPS)
1
K
2
3
4
5
6
9-2 Lista de Control Preliminar (Un Solo UPS)
Todos los interruptores de los interruptores de circuito deben estar apagados, incluyendo el interruptor de circuitos del gabinete de baterías • externas (si lo hubiera).
Confirme que no existen voltajes potenciales entre el Neutro y la Tierra.• Confirme que la fuente de energía de entrada tenga los mismos valores (voltaje, frecuencia y fase) que los del sistema UPS.
Nota: Después del arranque, el sistema UPS efectuará una breve auto prueba y mostrará los resultados en la pantalla LCD. Después de una auto prueba exitosa, el sistema UPS suministrará energía CA a la carga de los equipos conectados.
9-3 Procedimiento de Arranque Normal (Un Solo UPS)
1
Si hay un gabinete de baterías externas conectado, encienda el interruptor de circuitos
2
Confirme que el interruptor de circuitos de derivación manual está apagado.
A
del gabinete de baterías externas.
A
1
A
7
8
9
10
11
77
12
A
Salida
2
Derivación
Manual
Entrada de Derivación
Entrada
Principal
13
14
Page 78
9 – Arranque, Apagado y Derivación (continuación)
1
9-3 Procedimiento de Arranque Normal (Un Solo UPS) (continuación)
3
Encienda el interruptor de circuitos de salida
2
circuitos de entrada de derivación
B
. Después de un breve proceso de inicialización, la pantalla LCD indicará “ON AUTO BYPASS”, [En derivación automática] el LED “BYPASS” [Derivación] se iluminará y salida del sistema UPS será suministrada por la fuente de energía derivada.
3
4
Encienda el interruptor de circuitos de la entrada principal
4
la fuente de energía CA es normal, El sistema UPS está listo para arrancar.
5
Presione el botón ON [encendido]
5
6
que escuche un pitido) y entonces suelte el botón. El inversor se activará y sincronizará con la fuente de derivación, y automáticamente cambiará de modo de derivación automática a modo en línea (normal). El LED “BYPASS” [Derivación] se obscurecerá y el LED “NORMAL” se iluminará.
A
por 3 segundos (hasta
7
A
y el interruptor de
A
3
. Si
4
A B
Salida
Salida
Derivación
Manual
Derivación
Manual
Entrada de Derivación
Entrada de Derivación
Entrada
Principal
A
Entrada
Principal
A
5
9-4 Procedimiento de Arranque de la Batería (Un Solo UPS)
8
Nota: La batería debe estar por lo menos parcialmente cargada para que esta operación tenga éxito.
Si hay un gabinete de baterías externas conectado, encienda el
1
interruptor de circuitos,
A
del gabinete de baterías externas.
9
10
1
2
Confirme que el interruptor de circuitos
A
está apagado.
11
12
13
3
Presione el botón ON [encendido]
A
por 3 segundos (hasta que escuche un pitido) y entonces suelte el botón. El inversor se activará, y utilizará la energía CD almacenada en la batería para suministrar energía CA al equipo conectado. El LED “BATTERY” [Batería] se iluminará.
2
Salida
A
Derivación
Manual
A
Entrada de Derivación
Entrada
Principal
A
14
3
78
Page 79
9 – Arranque, Apagado y Derivación (continuación)
9-5 Procedimiento de Derivación Manual (Un Solo UPS)
Advertencia: Colocando el sistema UPS en derivación manual deshabilitará el inversor y alimentará de corriente a todas las cargas de la fuente de derivación manual pero el sistema UPS aun estará activado. Antes de efectuar un mantenimiento o reparación del sistema UPS, apague y desactive completamente el sistema UPS siguiendo los pasos indicados en la estarán alimentadas las fuente de energía de la derivación, no será respaldados por la batería en el caso de una falla de energía del servicio público.
1
Cuando el sistema UPS esté en modo en línea (normal), presione el botón OFF
A
por 3 segundos (hasta que escuche un pitido), y entonces suelte el botón. El inversor automáticamente cambiará a modo de derivación y el LED “BYPASS” se iluminará.
1
2
Encienda el interruptor de circuitos de la derivación manual entonces apague el interruptor de circuitos de salida
A
, y
B
.
2
Sección 9-6. Aunque las cargas del equipo conectado
A
AB
Salida
Derivación
Manual
Entrada de Derivación
Entrada
Principal
1
2
3
4
5
6
9-6 Procedimiento de Apagado (Un Solo UPS)
Advertencia: El procedimiento de apagado del sistema UPS eliminará la salida de energía CA para todas las cargas. Antes de apagar, confirme que todas las cargas están apagadas o coloque el sistema UPS en modo de derivación manual para mantener todas las cargas alimentadas por la fuente de energía de derivación.
1
Presione el botón OFF [Apagado] escuche un pitido), y entonces suelte el botón. Si el sistema UPS está en modo en línea (normal), cambiará a modo de derivación. Si el sistema UPS está en modo de respaldo, el inversor se apagará y la energía CA de salida será interrumpida.
2
Apague el interruptor de circuitos de la entrada principal
3
Apague el interruptor de circuitos de la entrada de derivación
A
por 3 segundos (hasta que
1
A
.
Salida
2
A
.
Derivación
Manual
Entrada de Derivación
A
A
Entrada
Principal
7
8
9
10
11
12
79
A
13
Salida
3
Derivación
Manual
Entrada de Derivación
Entrada
Principal
14
Page 80
9 – Arranque, Apagado y Derivación (continuación)
1
9-6 Procedimiento de Apagado (Un Solo UPS) (continuación)
Confirme que el sistema UPS esté apagado que todos los circuitos
4
2
3
4
5
6
7
8
9
de la salida principal están apagados. Si el sistema UPS esta conectado a un gabinete de baterías externas, apague el interruptor de circuitos del gabinete de baterías externas
Apague el interruptor de circuitos de salida
5
entrada de energía CA es normal, el sistema UPS está listo para arrancar.
Nota: Si el sistema UPS permanecerá apagado por mucho tiempo, deberá encenderse periódicamente para permitir que las baterías se recarguen. El UPS deberá encenderse y las baterías recargarse al menos por un periodo ininterrumpido de 24 horas cada 3meses. Fallar en recargar las baterías periódicamente puede causará daños irreversibles a las baterías.
A
.
A
. Si la fuente de
4
Salida Derivación
5
A
A
Manual
Entrada de Derivación
Entrada
Principal
9-7 Lista de Control Preliminar (UPS en Paralelo)
Advertencia: La redundancia en paralelo requiere exactamente dos sistemas UPS (redundancia 1+1). No intente conectar más de dos sistemas UPS vía redundancia en paralelo. Los sistemas UPS deberán ser del mismo tipo y capacidad para una instalación de redundancia en paralelo. Intentar conectar sistemas UPS que no son similares dañara a los sistemas UPS y crea un serio riesgo de lesiones personales y daños a la propiedad.
Todos los interruptores de los interruptores de circuito deberán estar apagados, incluyendo los interruptores de circuito de los gabinetes
de baterías externas.
Confirme que no existen voltajes potenciales entre el Neutro y Tierra.• Confirme que la fuente de energía de entrada tenga los mismos valores (voltaje, frecuencia y fase) que los del sistema UPS.
Debe usar el panel de control para establecer que los números ID paralelos de los sistemas UPS sean 1 y 2. Vea la
para información acerca de como establecer los números ID paralelos.
Nota: Después del arranque, el sistema UPS efectuará una breve auto prueba y mostrará los resultados en la pantalla LCD. Después de una auto prueba exitosa, el sistema UPS suministrará energía CA a la carga de los equipos conectados.
Sección 10-11
9-8 Procedimiento de Arranque (UPS en Paralelo)
10
Conecte el cable de redundancia en paralelo
1
redundancia en paralelo DB9
B
de cada sistema UPS.
A
al puerto de
11
2
12
Si los sistemas UPS tienen gabinetes de batearías externas conectadas encienda el interruptor de circuitos de baterías.
A
de cada módulo
13
14
80
B
B
1
A
2
A
Page 81
9 – Arranque, Apagado y Derivación (continuación)
9-8 Procedimiento de Arranque (UPS en Paralelo) (continuación)
Encienda el interruptor de circuitos de entrada
3
UPS. Después de un breve proceso de inicialización la pantalla LCD indicará “ON AUTO BYPASS” [en derivación automática] y el LED “BYPASS” se iluminará.
4
Encienda el interruptor de circuitos de la entrada principal cada sistema UPS.
5
Presione el botón ON [encendido]
A
de uno de los sistemas UPS por 3 segundos (hasta que escuche un pitido), entonces suelte el botón. El inversor se activará y sincronizará con la fuente de derivación. Presione el botón ON [encendido] del otro sistema UPS por 3 segundos (hasta que escuche un pitido), entonces suelte el botón. Cuando el inversor de cada sistema UPS esté operando normalmente, automáticamente cambiarán a modo de derivación automática a modo en línea (normal) al mismo tiempo. El LED “BYPASS” [Derivación] se obscurecerá y el LED “NORMAL” se iluminará.
Revise el voltaje de salida de cada sistema UPS. La desviación de
6
fase de cada sistema UPS deberá ser menos de 5V. Si la desviación de fase está dentro de un rango aceptable, encienda el interruptor de circuitos de salida
A
de cada sistema UPS. Nota: Para más
información para revisar el voltaje de salida de cada sistema UPS, vea la
Sección 10-6.
A
de cada sistema
A
3
Salida
de
Salida
4
5
Salida
6
1
2
A
3
Derivación
Manual
Entrada de Derivación
Entrada
Principal
4
A
5
Derivación
Manual
Entrada de Derivación
Entrada
Principal
A
6
7
8
A
Derivación
Manual
Entrada de Derivación
Entrada
Principal
9
9-9 Procedimiento de Apagado (UPS en Paralelo)
Advertencia: El procedimiento de apagado del sistema UPS eliminará la salida de energía CA para todas las cargas. Antes de apagar, confirme que todas las cargas están apagadas o coloque el sistema UPS en modo de derivación manual para mantener todas las cargas alimentadas por la fuente de energía de derivación.
Por el sistema UPS que desea apagar, presione el botón OFF
1
[apagado] entonces suelte el botón. Si el otro sistema UPS puede soportar las cargas del equipo conectad solo, el sistema UPS que se apago apagará su inversor y su pantalla LCD indicará “LOAD NOT POWERED” [carga no alimentada]. La pantalla del otro sistema UPS indicará “ONLINE MODE” [modo en línea]. Si la carga total del equipo conectado es demasiado grande para ser manejada por un solo sistema UPS, ambos sistemas UPS apagarán sus inversores y cambiarán a modo de derivación y sus pantallas LCD indicarán “ON AUTO BYPASS” [en derivación automática].
2
Por el sistema UPS que desea apagar, apague el interruptor de circuitos de la entrada principal de circuitos de salida
A
por 3 segundos (hasta que escuche un pitido),
A
, y luego apague el interruptor
B
.
81
1
2
Salida
Derivación
Manual
Entrada de Derivación
A
AB
Entrada
Principal
10
11
12
13
14
Page 82
9 – Arranque, Apagado y Derivación (continuación)
1
9-9 Procedimiento de Apagado (UPS en Paralelo) (continuación)
Por el sistema UPS que desea apagar, apague el interruptor de
3
2
circuitos de entrada de derivación
3
4
Cuando el sistema UPS esté completamente apagado, la pantalla LCD estará completamente apagada. Si los sistemas UPS tienen gabinetes de baterías externas conectado, apague el interruptor de
4
5
6
7
8
9
circuitos del gabinete de baterías externas baterías.
Nota: Si el sistema UPS permanecerá apagado por mucho tiempo, deberá encenderse periódicamente para permitir que las baterías se recarguen. El UPS deberá encenderse y las baterías recargarse al menos por un periodo ininterrumpido de 24 horas cada 3 meses. Fallar en recargar las baterías periódicamente puede causará daños irreversibles a las baterías.
9-10 Procedimiento de Derivación Manual (UPS en Paralelo)
Advertencia: Cuando el sistema UPS está en derivación manual, el inversor se apaga. Las cargas del equipo conectado son alimentadas la fuente de energía de la derivación y no recibirán respaldo de la batería durante una falla de energía del servicio público.
Por el primer equipo que quiere apagar, presione el botón OFF
1
[apagado] entonces suelte el botón. Si el otro sistema UPS puede soportar las cargas del equipo conectad solo, el sistema UPS que se apagó apagará su inversor y su pantalla LCD indicará “LOAD NOT POWERED” [carga no alimentada]. La pantalla del otro sistema UPS indicará “ONLINE MODE” [modo en línea]. Si la carga total del equipo conectado es demasiado grande para ser manejada por un solo sistema UPS, ambos sistemas UPS apagarán sus inversores y cambiarán a modo de derivación y sus pantallas LCD indicarán “ON AUTO BYPASS” [en derivación automática]. Repita el paso 1 por el segundo sistema UPS que quiere apagar.
2
Apague el interruptor de circuitos principal UPS.
A
por 3 segundos (hasta que escuche un pitido),
A
.
A
A
de cada módulo de
A
de cada sistema
3
Salida
4
1
Derivación
Manual
A
Entrada de Derivación
Entrada
Principal
A
A
10
11
12
13
14
Confirme que ambos sistemas UPS están apagados, entonces
3
encienda el interruptor de circuitos de la derivación manual cada sistema UPS. La fuente de energía de la derivación alimentará las cargas y la pantalla LCD indicará “ON MANUAL BYPASS” [en derivación manual].
Apague el interruptor de circuitos de la entrada de derivación
4
y el interruptor de circuitos de salida B de cada sistema UPS. La pantalla LCD se apagará completamente.
Salida
2
A
de
Salida
3
A
Salida
4
82
Derivación
Manual
A
Derivación
Manual
Derivación
Manual
Entrada de Derivación
Entrada de Derivación
AB
Entrada de Derivación
Entrada
Principal
Entrada
Principal
Entrada
Principal
Page 83
9 – Arranque, Apagado y Derivación (continuación)
9-10 Procedimiento de Derivación Manual (UPS en Paralelo) (continuación)
Si los sistemas UPS tienen un gabinete de baterías externas
5
conectado apague el interruptor de circuitos del gabinete de baterías externas
De este modo, únicamente el interruptor de circuitos de salida
6
el bloque de terminales
A
de cada módulo de baterías.
B
tienen voltaje peligroso, lo que permite que personal de servicio calificado efectúe el mantenimiento o reparación. Nota: El personal de servicio calificado puede preferir
desactivar el sistema UPS completamente, dependiendo de los códigos locales y la naturaleza del mantenimiento o reparación.
5
A
y
A
6
A
1
2
3
4
B
5
9-11 Cambiando de Derivación Manual a Modo Normal (UPS en Paralelo)
Si los sistemas UPS tienen un gabinete de baterías externas
1
conectado encienda el interruptor de circuitos del gabinete de baterías externas
2
Encienda el interruptor de circuitos de la entrada de derivación
A
de cada módulo de baterías.
y el interruptor de circuitos de salida B de cada sistema UPS.
Confirme que las pantallas LCD de ambos sistemas UPS indican
3
“ON MANUAL BYPASS”, y entonces apague el interruptor de circuitos de entrada derivación manual
A
de cada sistema UPS. La pantalla LCD indicará “ON AUTO BYPASS” [en derivación automática].
4
Encienda el interruptor de circuitos principal
A
de cada sistema
UPS.
5
Presione el botón ON [encendido]
A
del primer sistema UPS por 3 segundos (hasta que escuche un pitido), entonces suelte el botón. Presione el botón ON [encendido] del segundo sistema UPS por 3 segundos (hasta que escuche un pitido), entonces suelte el botón. Cuando el inversor de cada sistema UPS esté operando normalmente, cambiarán a modo en línea (normal) al mismo tiempo.
1
A
Salida
2
Salida
3
A
Derivación
Manual
Derivación
Manual
6
7
8
AB
Entrada de Derivación
A
Entrada de Derivación
Entrada
Principal
Entrada
Principal
9
10
11
12
A
Salida
Derivación
Manual
Entrada de Derivación
A
Entrada
Principal
83
13
54
14
Page 84
10 – Pantalla y Confi guración
1
10-1 Diagrama del Panel de Control
LED “NORMAL” [En Línea]
A
2
3
4
5
LED “BATTERY” [Batería]
B
LED “BYPASS” [Derivación]
C
LED “FAULT” [Falla]
D
Pantalla LCD de Estado
E
Botón “ESC” (Escape)
F
Botones de Recorrido (
G
Botón Entrar (
H
I
Botón de Encendido Botón de Apagado
J
Botón “EPO” (Apagado de Emergencia)
K
y )
)
10-2 Jerarquía del Despliegue de la Información en la Pantalla
E
F
I
K
A
B
G
C
D
J
H
Panel de Control
6
7
8
9
10
11
12
Nivel 2
Measure
[Medidas/Valores]
Nivel 3 Nivel 3
Output Load [Carga de la Salida]
Mains Input [Entrada Principal]
Bypass Input [Entrada de Derivación]
Inverter Output [Salida del Inversor]
Module [Módulo] 1/2/3/4
UPS Output [Salida del UPS]
Nivel 1
Bienvenido/
Diagrama del UPS
Nivel 2 Nivel 2
UPS Setup
[Instalación
del UPS]
[Instalación de la Derivación] »
Voltage Range [Rango de Voltaje] » Frequency Range [Rango de Frecuencia]
[Instalación de la Salida]
Inverter Frequency [Frecuencia del Inversor ](50/60Hz) » ECO Mode (Enable/Disable) [Modo ECO (Habilitar/Deshabilitar)] » Frequency Converter Mode [Modo de Convertidor de Frecuencia] »
Battery Setup [Instalación de la Batería] »
EXT Battery Type [Tipo de Batería EXT] » Charger Current [Corriente Cargador ]» Battery Date [Fecha de Batería] » Auto Battery Test [Prueba Auto de la Batería] »
Bypass Setup
Output Setup
Nivel 1
Alarma/
Info de Falla
Nivel 4/5
Nivel 4/5
Nivel 4/5
Maintenance
[Mantenimiento]
Nivel 3
Statistics [Estadísticas]
Read [Leer] », Reset [Restaurar] »
Event Log [Registro de Eventos] »
Read [Leer] » Erase [Borrar] »
Manual Setup and Test [Instalación Manual y Prueba] »
Force boost charge [Incrementar Tasa de Recarga] » Manual battery test [Prueba Manual de la Batería] » LED & Buzzer test [Prueba de LED y Alarma] » CLR BAT test result [BORR res Prueba BAT] »
FW Upgrade [Actualización FW]
System FW [FW del Sistema] », Power Module FW [FW del Módulo de Potencia] »
Nivel 4/5
Nivel 4/5
Nivel 4/5
Nivel 4/5
13
14
Battery [Batería] »
Status [Estado]
Temperature [Temperatura] »
Bypass STS [STS de la Derivación]
Module Temperature [Temperatura del Módulo] »
Module [Módulo] Event Log 1/2/3/4 PFC Inverter [Inversor]
Capacity [Capacidad] Test Result [Resultado de la Prueba]
Local Setup [Instalación Local] »
Date/Time Change [Cambio de Fecha/Hora] », Password Change » Admin/User [Cambio de Contraseña » Admin/Usuario] » Parallel UPS ID Setting [Ajuste Paralelo UPS ID] » Audible (Enable, Disable, Mute) [Audible (Habilitar, Deshabilitar, [Silencio)]» Display [Pantalla] » Language [Idioma] » Serial COM ID [Serial COM ID] »
Nivel 4/5
84
Other [Otros]
S/N&FW version [Versión S/N y FW] » System time [Hora del sistema] » Module DCBUS Volt [Volt de Mod CCBUS] »
Nivel 4/5
Page 85
10 – Pantalla y Confi guración (continuación)
10-3 Pantalla Inicial (Predeterminada)
Después que el sistema UPS arranca y completa la auto prueba,
1
la pantalla LCD de estado mostrará la pantalla inicial. La pantalla inicial incluye un mensaje de estado y un diagrama que muestran el estado operacional del sistema UPS. Si un evento de alarma se presenta, un signo de exclamación destellará en la esquina derecha inferior de la pantalla LCD de estado.
Presione el botón de recorrido hacía abajo (
2
del evento, que puede incluir información de diagnóstico. Presione nuevamente el botón de recorrido hacia abajo ( siguiente mensaje. Si no existe otro mensaje, la pantalla regresará a la pantalla inicial. Note: Presionando el botón “ESC” regresará a
la pantalla inicial.
) para ver el mensaje
) para ver el
1
2
3
1
4
5
2
10-4 Mensajes de Estado y Diagramas
La salida del sistema UPS está apagada y las cargas del equipo
1
conectado no están siendo alimentadas Esta condición puede deberse a un apagado automático del UPS o a haber apagado manualmente el interruptor de circuitos de salida.
Las cargas del equipo conectado están alimentadas por la fuente de
2
energía de derivación al arranque inicial del sistema UPS.
3
El sistema UPS está arrancando con la energía de las baterías.
6
7
1
8
9
2
10
11
El sistema UPS está en modo de derivación automática. Las cargas
4
del equipo conectado perderán energía si la fuente de energía de la derivación falla.
85
3
12
13
4
14
Page 86
10 – Pantalla y Confi guración (continuación)
1
10-4 Mensajes de Estado y Diagramas (continuación)
El sistema UPS está operando en modo en línea (normal). Las
5
2
3
4
5
6
7
cargas del equipo conectado recibirán energía de respaldo de la batería si falla la fuente de energía principal (servicio público o generador).
6
El sistema UPS ha cambiado a modo de respaldo de la batería (on battery). Las cargas del equipo conectado está recibiendo energía de respaldo de la batería, y se muestra el tiempo de respaldo estimado. Nota: Los parámetros de la batería deben estar
ajustados correctamente a fin de recibir estimados de tiempo de respaldo correctos del sistema UPS cuando éste cambie a modo de respaldo. Ve al
El sistema UPS ha cambiado a modo de respaldo de la batería (on
7
battery). Las cargas del equipo conectado aun están recibiendo energía CA invertida de la energía de la batería pero la batería está casi agotada.
Sección 10-10 para más información.
5
6
10
11
12
13
8
El sistema UPS está efectuando una prueba de la batería.
8
7
9
8
9
El sistema UPS está operando en modo de economía y las cargas del equipo conectado están siendo alimentadas por la fuente de la derivación.
9
10
El sistema UPS está en modo de derivación manual a fin de permitir que personal de servicio calificado efectúe el mantenimiento o reparación del sistema UPS. Las cargas del equipo conectado perderán la energía si la fuente de la derivación falla.
14
10
86
Page 87
10 – Pantalla y Confi guración (continuación)
10-5 Menú Principal
Desde la pantalla inicial, presione el botón Entrar ( ) para
1
acceder al menú principal. Presione el botón de recorrido hacia abajo ( cursor. Presione el botón Entrar ( opciones del menú disponibles.
10-6 Menú de Mediciones del Sistema UPS
Presione el botón Entrar ( ) Para seleccionar “MEASURE” del
1
menú principal. Use los botones de recorrido (
2
pantallas de información disponibles. Presione el botón “ESC” para regresar al menú anterior.
Muestra el SU40K
) o el botón de recorrido hacia arriba ( ) para mover el
) para seleccionar una de las
o ) para navegar por las
1
2
1
3
4
1
5
6
7
8
9
10
11
12
13
14
2
87
Page 88
10 – Pantalla y Confi guración (continuación)
1
10-7 Menú de Instalación del Sistema UPS
Presione el botón Entrar ( ) para seleccionar “UPS SETUP”
1
2
3
4
5
6
7
desde el menú principal.
Accediendo al menú de instalación del sistema UPS requiere
2
de una contraseña. Desde la pantalla de inicio de sesión [log in screen], presione el botón Entrar ( como administrador o usuario. Los administradores pueden ver y cambiar los parámetros del sistema UPS, los usuarios regulares pueden ver todos los parámetros pero solo pueden cambiar algunos parámetros básicos. Únicamente el personal de servicio calificado deberá ingresar como el administrador.
3
La contraseña consiste de 4 números. Presione el botón de recorrido hacia abajo ( para seleccionar el primer número, presione el botón entrar (
) para ingresar el número elegido. Después de ingresar el último número, presione el botón entrar ( la selección de la contraseña. La contraseña predeterminada de fábrica para el usuario es 0000. La contraseña predeterminada de fábrica para el administrador es 0000. Únicamente el personal de servicio calificado deberá tener acceso a la contraseña del administrador Vea la cambiar las contraseñas.
4
Después de que la contraseña correcta haya sido ingresada, la pantalla LCD mostrará el menú de instalación del sistema UPS.
) o el botón de recorrido hacia arriba ( )
Sección 10-11 por instrucciones de cómo
) para elegir si inicia la sesión
) para confirmar
1
2
3
8
9
10-8 Menú de Instalación de la Derivación
10
Ingrese al menú de instalación del sistema UPS como se describe
1
en la Sección 10-7. Use los botones de recorrido ( mover el cursor a “BYPASS SETUP”, entonces presione el botón entrar (
).
11
12
2
Use los botones de recorrido ( seleccionar “VOLTAGE RANGE” o “FREQUENCY RANGE”.
, ) y el botón entrar ( ) para
13
4
, ) para
1
14
2
88
Page 89
10 – Pantalla y Confi guración (continuación)
10-8 Menú de Instalación de la Derivación (continuación)
Desde la pantalla “VOLTAGE RANGE”, use los botones de
3
recorrido ( derivación y presione el botón entrar (
4
Desde la pantalla “FREQUENCY RANGE”, use los botones de recorrido ( derivación y presione el botón entrar (
Nota: Presione el botón “ESC” para regresar al menú anterior.
, ) para seleccionar el rango de voltaje de la
) para confirmar el ajuste.
, ) para seleccionar el rango de frecuencia de la
) para confirmar el ajuste.
1
2
3
3
4
5
4
6
10-9 Menú de Instalación de la Salida
Nota: El sistema UPS debe estar en modo de derivación para cambiar los parámetros de la Salida.
1
Ingrese al menú de instalación del sistema UPS como se describe en la
Sección 10-7. Use los botones de recorrido ( , ) para
mover el cursor a “OUTPUT SETUP”, entonces presione el botón entrar (
Use los botones de recorrido (
2
elegir una de las opciones del menú.
3
Desde la pantalla “VOLTAGE”, use los botones de recorrido ( entrar (
).
, ) y el botón entrar ( ) para
, ) para seleccionar el ajuste deseado y presione el botón
) para confirmar el ajuste.
7
8
1
9
10
2
11
89
12
3
13
14
Page 90
10 – Pantalla y Confi guración (continuación)
1
10-9 Menú de Instalación de la Salida (continuación)
4
Desde la pantalla “FREQUENCY”, use los botones de recorrido
, ) para seleccionar el ajuste deseado y presione el botón
2
3
4
5
6
7
( entrar (
frecuencia de salida únicamente se usa cuando el sistema UPS arranque con la batería o cuando el modo de convertidor de frecuencia (vea el paso 6) está habilitado.
Desde la pantalla “ECONOMIC MODE”, use los botones de
5
recorrido ( botón entrar (
6
Desde la pantalla “FREQ CONVERTER MODE”, use los botones de recorrido ( presione el botón entra (
Nota: Presione el botón “ESC” para regresar al menú anterior.
) para confirmar el ajuste. Nota: El ajuste de la
, ) para seleccionar el ajuste deseado y presione el
) para confirmar el ajuste.
, ) para seleccionar el ajuste deseado y entonces
) para confirmar el ajuste.
4
5
8
6
10-10 Menú de Instalación de la Batería
Nota: El sistema UPS debe estar en modo de derivación para cambiar los parámetros de la batería. Los parámetros de la batería deben ser fijados correctamente a fin de recibir estimados de tiempo de respaldo correctos del sistema UPS cuando éste cambie a modo de respaldo.
9
1
Ingrese al menú de instalación del sistema UPS como se describe
10
en la Sección 10-7. Use los botones de recorrido ( mover el cursor a “BATTERY SETUP”, a continuación presione el botón entrar (
).
, ) para
11
1
2
Use los botones de recorrido ( seleccionar una de las opciones del menú.
, ) y el botón entrar ( ) para
12
13
2
14
90
Page 91
10 – Pantalla y Confi guración (continuación)
10-10 Menú de Instalación de la Batería (continuación)
3
Desde la pantalla “EXT BAT TYPE”, use los botones de recorrido (
, ) para seleccionar los ajustes deseados y presione el botón
entrar (
posibles son 26AH, 40AH, 100AH o 140AH. Los posibles ajustes a las cadenas son 1, 2, 3 ó 4.
4
Desde la pantalla “CHARGER CURRENT” use los botones de recorrido ( el botón entrar (
predeterminado para la corriente es 7A.
) para confirmar los ajustes. Nota: los tipos de baterías
, ) para seleccionar los ajustes deseados y presione
) para confirmar los ajustes. Nota: El ajuste
1
2
3
3
4
5
Desde la pantalla “BAT DATE SETTING”, use los botones de
5
recorrido ( el botón entrar (
6
Desde la pantalla “AUTO BAT TEST”, use los botones de recorrido ( el botón entrar (
Nota: Presione el botón “ESC” para regresar al menú anterior.
, ) para seleccionar los ajustes deseados y presione
) para confirmar los ajustes.
, ) para seleccionar los ajustes deseados y presione
) para confirmar los ajustes.
4
6
7
5
8
9
10
6
11
91
12
13
14
Page 92
10 – Pantalla y Confi guración (continuación)
1
10-11 Menú de Instalación Local
Ingrese al menú de instalación del sistema UPS como se describe
1
en la
2
3
2
4
5
6
3
7
Sección 10-7. Use los botones de recorrido ( , ) para
mover el cursor a “LOCAL SETUP”, y oprima el botón entrar (
).
Use los botones de recorrido ( seleccionar una de las opciones del menú.
Desde la pantalla “DATE/TIME CHANGE” , use los botones de recorrido ( botón entrar (
este ajuste no es necesario la contraseña del administrador, con la contraseña de usuario es suficiente.
, ) para seleccionar el ajuste deseado y presione el
) para confirmar los ajustes. Nota: para cambiar
, ) y el botón entrar ( ) para
1
2
10
11
12
13
8
Desde la pantalla “PASSWORD CHANGE”, use los botones de
4
recorrido ( deseado Use los botones de recorrido ( ajuste deseado y presione el botón entrar (
9
ajuste. Nota: La contraseña de administrador únicamente debe ser usada únicamente por personal calificado.
Desde la pantalla “PARALLEL ID”, use los botones de recorrido
5
(
, ) para seleccionar los ajustes deseados y presione el botón
entrar (
sistemas UPS en configuración de redundancia en paralelo, Los números ID de paralelo de los sistemas UPS deben ser 1 y 2.
, ) y el botón entrar ( ) para seleccionar el menú
, ) para seleccionar el
) para confirmar el
) para confirmar los ajustes. Nota: Si se usan dos
3
4
4b
14
5
92
Page 93
10 – Pantalla y Confi guración (continuación)
10-11 Menú de Instalación Local (continuación)
Desde la pantalla “AUDIBLE”, use los botones de recorrido
6
(
, ) para seleccionar los ajustes deseados para la alarma audible
y presione el botón entrar (
Desde la pantalla “DISPLAY”, use los botones de recorrido (
7
para seleccionar el contraste deseado de la pantalla LCD y presione el botón entrar (
este parámetro no necesita iniciar la sesión como administrador – hacerlo como usuario es suficiente.
Desde la pantalla “LANGUAGE”, use los botones de recorrido
8
(
, ) para seleccionar el ajuste deseado y presione el botón
entrar (
parámetro no necesita iniciar la sesión como administrador -­hacerlo como usuario es suficiente.
) para confirmar el ajuste. Nota: para cambiar este
) para confirmar el ajuste. Nota: para cambiar
) para confirmar el ajuste.
, )
1
2
3
6
4
5
7
6
7
9
Desde la pantalla “SERIAL COM ID”, use los botones de recorrido ( serial y presione el botón entrar (
Nota: Este ajuste no aplica para las conexiones RS-232 estándar. Solo aplica para las comunicaciones RS-485/ RS-422.
Nota: Presione el botón “ESC” para regresar al menú anterior.
, ) para seleccionar el ID deseado para el puerto
) para confirmar el ajuste.
10-12 Menú de Mantenimiento
Presione el botón entrar ( ) para seleccionar
1
“MAINTENANCE” del menú principal. Siga el procedimiento de inicio de sesión descritos en el paso 1 y el paso 2 de la
10-7
.
2
Después de introducir la contraseña correcta, la pantalla LCD mostrará el menú de mantenimiento. Use los botones de recorrido (
, ) y el botón entrar ( ) para elegir una opción del menú.
Sección
8
8
9
9
10
11
1
12
13
93
2
14
Page 94
10 – Pantalla y Confi guración (continuación)
1
10-13 Menú de Estadísticas
Ingrese al menú de mantenimiento como se describe en la Sección
1
10-12
2
3
2
4
5
6
3
. use los botones de recorrido ( , ) para mover el cursor a
“STATISTIC”, entonces presione el botón entrar (
Si desea ver la información estadística, use los botones de recorrido ( del menú.
La información estadística disponible incluye el tiempo total de operación, el número de eventos de la batería y el número de eventos de la derivación.
, ) y el botón entrar ( ) para seleccionar “READ”
).
1
2
7
8
4
Si desea restaurar la información estadística, use los botones de recorrido ( del menú.
, ) y el botón entrar ( ) para seleccionar “RESET”
9
10
Debe introducir la contraseña del administrador para confirmar la
5
operación de restauración.
Nota: Presione el botón “ESC” para regresar al menú anterior.
11
12
3
4
5
13
14
94
Page 95
10 – Pantalla y Confi guración (continuación)
10-14 Menú de Registro de Eventos
Ingrese al menú de mantenimiento como se describe en la Sección
1
10-12
. use los botones de recorrido ( , ) para mover el cursor a
“EVENT LOG”, entonces presione el botón entrar (
2
Si desea ver el registro de eventos, use los botones de recorrido (
, ) y el botón entrar ( ) para seleccionar “READ” del menú
de registros de eventos.
Use los botones de recorrido (
3
eventos. Presione el botón “ESC” para regresar al menú anterior.
, ) para navegar por el registro de
).
1
2
3
1
4
5
2
6
Si desea borrar el registro de eventos, use los botones de recorrido
4
(
, ) y el botón entrar ( ) para seleccionar “ERASE” del
menú de registros de eventos.
5
Debe introducir la contraseña del administrador para confirmar la operación de restauración.
Nota: Presione el botón “ESC” para regresar al menú anterior.
7
3
8
9
4
10
11
5
12
95
13
14
Page 96
10 – Pantalla y Confi guración (continuación)
1
10-15 Menú de instalación Manual y Prueba
1
Ingrese al menú de mantenimiento como se describe en la Sección
10-12
2
3
2
4
5
6
3
7
. Use los botones de recorrido ( , ) para mover el cursor a “MANUAL SETUP & TEST”, entonces presione el botón entrar (
).
Use los botones de recorrido ( seleccionar una opción del menú.
Seleccione “FORCE BOOST CHARGE” para incrementar la tasa de recarga de la batería. Debe introducir la contraseña del administrador para confirmar esta operación. Advertencia:
Aumentar la tasa de recarga de la batería por un período prolongado puede dañar al sistema de baterías.
, ) y el botón entrar ( ) para
1
2
8
Seleccione “MANUAL BATTERY TEST” para iniciar una prueba
4
de la batería . Debe introducir la contraseña del administrador para confirmar esta operación.
9
10
Seleccione “BUZZER AND LED TEST” para iniciar una prueba
5
de los LEDs del panel de control y la alarma audible. Debe introducir la contraseña del administrador para confirmar esta operación.
11
12
6
Seleccione “CLR BAT TEST RESULT” para remover los resultados de la prueba de la batería del menú “MEASURE”. (Vea la
13
Sección 10-6 para más información.)
Nota: Presione el botón “ESC” para regresar al menú anterior.
3
4
5
14
6
96
Page 97
10 – Pantalla y Confi guración (continuación)
10-16 Menú de Actualización del Firmware
Advertencia: El firmware debe ser actualizado únicamente por personal de servicio calificado. Use únicamente firmware que haya sido aprobado por Tripp Lite. Fallar en cumplir este requisito anulará la garantía.
1
Ingrese al menú de mantenimiento como se describe en la
10-12
. Use los botones de recorrido ( , ) para mover el cursor a
“FIRMWARE UPGRADE”, entonces presione el botón entrar
).
(
Sección
1
2
3
Use los botones de recorrido (
2
seleccionar una de las opciones del menú. Debe introducir la contraseña del administrador para confirmar esta operación.
Nota: Presione el botón “ESC” para regresar al menú anterior.
, ) y el botón entrar ( ) para
10-17 Otras Opciones del Menú
1
Ingrese al menú de mantenimiento como se describe en la Sección
10-12
. Use los botones de recorrido ( , ) para mover el cursor a
“OTHERS”, entonces presione el botón entrar (
2
Use los botones de recorrido ( seleccionar una opción del menú. “SN & FW VERSION” muestra el número de serie y la versión del firmware del sistema UPS. “SYSTEM TIME” muestra la fecha y hora actual del sistema UPS. “MODULE DC BUS VOLT” muestra el voltaje actual del bus CD. El personal de servicio calificado puede querer ver esta información cuando esté efectuando mantenimiento o reparaciones al sistema UPS.
Nota: Presione el botón “ESC” para regresar al menú anterior.
, ) y el botón entrar ( ) para
).
1
4
5
6
2
7
8
1
9
10
2
11
97
12
13
14
Page 98
11 – Comunicaciones
1
Nota: Las conexiones para comunicaciones descritas en esta sección son opcionales. El sistema UPS funcionara correctamente sin estas conexiones.
2
11-1 Interfases de Comunicaciones
Ranura para SNMPWEBCARD
3
4
5
Interfaz de Entrada de
contacto Seco
6
Puerto de Redundancia
7
en Paralelo
Interfaz de Salida
de Contacto Seco
Puerto Serial
RS-232
11-2 Ranura para SNMPWEBCARD
8
Remueva la tapa del panel para instalar el accesorio SNMPWEBCARD de Tripp Lite. El accesorio SNMPWEBCARD proporciona una interfaz Ethernet para el sistema UPS y permite monitoreo remoto y control vía SNMP, navegador Web o telnet. Llame al +1 773 869 1234 para más información acerca de como ordenar el accesorio SNMPWEBCARD.
9
11-3 Interfaz de Entrada de Contacto Seco
La interfaz de entrada de contacto seco recibe instrucciones de cierre de contacto que permiten al sistema UPS recibir ordenes y monitorear las condiciones de la batería externa:
P1—Apagado de Emergencia Remoto (EPO)
10
P2—Entradas Auxiliares de Contacto seco (2 Juegos) P3—Temperatura del Gabinete de Baterías Externas 1 P4—Temperatura del Gabinete de Baterías Externas 2 P5—Temperatura del Gabinete de Baterías Externas 3
11
P6—Temperatura del Gabinete de Baterías Externas 4 P7—Estado de la Batería Externa
12
13
14
98
Page 99
11 – Comunicaciones (continuación)
11-4 Diagrama de Circuitos del Apagado de Emergencia Remoto (EPO)
La conexión de entrada del Apagado de Emergencia Remoto (EPO) (P1) le permite conectar el sistema UPS al circuito EPO de sus instalaciones. Conectar el sistema UPS al circuito EPO permite el cierre de emergencia remoto de la salida del sistema UPS. Conecte la entrada EPO a un interruptor remoto, proporcionado por el usuario, siguiendo el diagrama de circuito de abajo. Este contacto normalmente está abierto.
1
2
P1
11-5 Diagrama de Circuitos de la Entrada Auxiliar de Contacto Seco
Las conexiones de la entrada auxiliar del contacto seco (P2) le permite al sistema UPS recibir señales externas. Estos contactos normalmente están abiertos.
P2
3
4
5
6
7
8
11-6 Entradas la Temperatura del Gabinete de Baterías Externas
Las conexiones de entrada de la temperatura del gabinete de baterías externas (P3, P4, P5, P6) permiten al sistema UPS recibir señales de un accesorio opcional que monitorea la temperatura de los gabinetes de baterías externas. Llame al +1 773 869 1234 para más información.
11-7 Entrada del Estado de las Baterías Externas
La conexión de entrada del estado del gabinete de baterías externas (P7) le permite al sistema UPS recibir señales externas del estado del gabinete de baterías externas mediante un cable opcional. Pin 1 = +12V; Pin 2 = Cable de detección conectado; Pin 3 = Estado del interruptor de circuitos del gabinete de baterías (señal activa= interruptor de circuitos encendido; señal inactiva = apagado); Pin 4 = reservado; Pin 5 = voltaje de referencia. Llame al +1 773 869 1234 para más información.
9
10
11
12
13
14
99
Page 100
11 – Comunicaciones (continuación)
1
11-8 Detalle de la Interfaz de Salida del Contacto Seco
El sistema UPS tiene seis conexiones de salida de contacto seco. Estos contactos pueden estar normalmente abiertos o normalmente cerrados.
2
Mensajes Predeterminados
Contacto Mensaje Descripción
Pin 1-2 Carga en el inversor El sistema UPS está trabajando normalmente.
3
Pin 3-4 Carga en derivación automática El sistema UPS está en modo de derivación. Pin 5-6 Falla de la entrada principal con carga No hay energía del servicio público (Apagón) o anormal. El sistema UPS está en modo
en el inversor de respaldo. Pin 7-8 Batería baja El sistema UPS está en modo de respaldo, y el voltaje de la batería es menor a 220V.
4
Pin 9-10 Entrada de la derivación anormal La entrada de la derivación es anormal (frecuencia / fase). Pin 11-12 Falla en la prueba de la batería El voltaje de la batería es más bajo que el valor de referencia.
5
Mensaje Descripción
Falla de comunicación interna La comunicación con uno de los componentes internos no es normal. Falla externa en la comunicación en paralelo En una instalación de redundancia en paralelo, la comunicación en paralelo no es normal.
6
Advertencia/apagado por sobrecarga en la salida La carga excede la capacidad del sistema UPS. Apagado por falla en el módulo de potencia Se ha apagado el sistema UPS debido a una falla del módulo de potencia interno. Advertencia del módulo de potencia Un módulo de potencia interno tiene un error, pero el sistema UPS aun puede funcionar
normalmente.
7
EPO activado La salida del sistema UPS está deshabilitada por la función de Apagado de Emergencia (EPO). Derivación manual o automática El sistema UPS está en modo derivación manual. Advertencia/apagado por sobre calentamiento La temperatura del gabinete de baterías externas es demasiado alta.
del gabinete de baterías
8
Voltaje de Salida anormal El voltaje de salida del sistema UPS es demasiado alta o demasiada baja. La batería necesita ser remplazada De acuerdo a la información de la fecha en “BAT DATE SETTING”, [Establecimiento de la
fecha de la batería] el sistema UPS esta retrasado en el remplazo de la batería. (Vea la
9
Advertencia/apagado por sobre temperatura La temperatura del “interruptor de transferencia estático” [static transfer switch] (STS) en la derivación de la derivación es demasiado alta.
Falla en la tierra de la batería La batería tiene un error en la conexión a tierra. Falla del interruptor estático (STS) de la derivación El “interruptor de transferencia estático” [static transfer switch] (STS) de la derivación
está funcionando de forma anormal.
10
Nota: Si necesita habilitar mensajes opcionales, comuníquese con Tripp Lite.
Mensajes Opcionales
Sección 10-10 para más información.)
11
12
13
14
100
Loading...