Trinity TLS-4805, TLS-4804 User Manual
TRINITY 56” ROLLING WORKBENCH – STAINLESS STEEL
Model # TLS-4804 (Stainless Body)
TLS-4805 (Black Body)
OWNER’S MANUAL
Everything in its place.
®
Your TRINITY 56in Stainless Steel Workbench should include the following parts. Please
inspect box contents to ensure you have received all components.
If you are missing any parts, need assistance with assembly or have questions, please contact
TRINITY Customer Service: 800.985.5506 or customerservice@trinityii.com. Parts can also be
requested online via our “Contact Us” section at www.trinityii.com.
You will need 10mm wrench (for handles) and 14mm wrench (for casters) for assembly. Not
included.
PARTS LIST
A
SIDE HANDLE (2)
B C
CASTER BOLT (16)
M10
D
LINER (7)
E
G
H
HANDLE BOLT (12)
M6
LOCKING
CASTER (2)
F
NON-LOCKING
CASTER (2)
KEY (2)
© 2016 TRINITY - 800.985.5506
1
WORKBENCH (1)
I
SHELF (1)
ASSEMBLY INSTRUCTIONS
Position SIDE HANDLE (B) over pre-installed
nuts on the side of WORKBENCH (A). Insert
HANDLE BOLTS (C) through holes on SIDE
HANDLE (B). Use a 10mm wrench to tighten
HANDLE BOLTS (C) to WORKBENCH (A).
Repeat these instructions to install the other
SIDE HANDLE (B).
A
B
C
© 2016 TRINITY - 800.985.5506
2
STEP 1
STEP 2
10mm
A (1) B (2)
C (12)
Location of parts:
1) HANDLES (B) / FASTENERS (C/F) /
CASTER (D/E) / LINERS (G) / KEYS
(H) are all in accessory boxes inside
the lowest drawer. KEYS (H) are
taped outside the caster box.
NOTE: Drawer lock and cabinet
lock use different keys, please
match code on lock to the code
on the key
2) SHELF (I) is upside down at the
bottom inside the cabinet.
1
2
ASSEMBLY INSTRUCTIONS
© 2016 TRINITY - 800.985.5506
3
STEP 3
D (2) E (2)
F (16)
Lay WORKBENCH (A) on its backside. Two
people are needed. Do NOT attempt this alone.
Position LOCKING CASTERS (D) on the side of
the WORKBENCH (A) of your choice and align
holes to pre-installed nuts on the underside of
WORKBENCH (A). Use a 14mm socket wrench
to fully tighten CASTER BOLT (F) to
WORKBENCH (A).
Repeat above step to install the NON-LOCKING
CASTERS (E).
Notes:
* Make sure to install both of the LOCKING
CASTERS (D) on the same side.
** For ease of use, place LOCKING CASTERS
(D) on the side you will regularly push or pull.
*** If you plan to push the Tool Chest against a
wall, place LOCKING CASTERS (D) on the front
long side for ease of access.
14mm
A
Carefully lift Workbench upright. Two people
are needed. Do NOT attempt this alone.
SHELF (I) is shipped upside down at the
bottom inside the cabinet. Tilt SHELF (I)
diagonally and remove from the cabinet. Flip
it over so the flat surface faces up and make
sure the tabs are on 2 sides.
Tilt SHELF (I) diagonally to move it to the
desired position. Once at the desired height,
secure SHELF (I) by pushing down on all 4
corners until SHELF (I) engages fully with the
tabs.
I (1)
STEP 4
E
D
F
I
Position Tab
Loading...