TRENDnet TPE-80WSv4 User Manual

Quick Installation Guide

TPE-80WS

Table of Contents

English ......................................................................................................

1. Before You Start

2. Hardware Installation .........................................................................

3. Configuring the Power Over Ethernet (PoE) Switch ..........................

Troubleshooting ........................................................................................

................................................................................

1

1
2
3

4

Version 07.19.2007

1. Before You Start

Package Contents

TPE-80WS

?

Quick Installation Guide

?

User's Guide CD-ROM

?

RS-232 Cable

?

Power Cord

?

Rack Mount Kit

?

System Requirements

Web Browser: Internet Explorer (5.5 or higher) or Netscape Navigator

?

(4.7 or higher).

?A computer with a network adapter properly installed.
?A RJ-45 network cable.

EIA standard 19” rack (Optional)

?

Note: The TPE-80WS only support Power over Ethernet (PoE) devices that
follow the IEEE 802.3af standard

Application

Advanced Wireless Pan & Tilt

Internet Camera Server

Advanced Day/Night Internet

Camera Server with Audio

108Mbps 802.11g

Wireless Access Point

(TEW-450APB)

Power over Ethernet

(PoE) Splitter

(TPE-80WS)

(TPE-102S)

Power over Ethernet

(PoE) Splitter

(TPE-102S)

Power over Ethernet

(PoE) Splitter

(TPE-102S)

(TV-IP400W)

8-Port Gigabit Web

Smart PoE Switch

(TV-IP301)

Power + Ethernet Data

1

English

108Mbps 802.11g

Hot-Spot Access Point

(TEW-453APB)

54Mbps 802.11g Wireless

PoE Access Point

(TEW-434APB)

PoE Internet

Camera Server

(TV-IP201P)

2. Hardware Installation

1. Connect the Power Cord to the
rear of the TPE-80WS and then
to a power outlet.

2. Connect a RJ-45 network cable
from the computer to an available
Ethernet port on the TPE-80WS.

3. Connect a RJ-45 cable from a PoE
port on the TPE-80WS to the LAN
Port of the PoE device (e.g.
TEW-434APB)

4. Verify that the following panel lights
are on: POWER, OPERATING and

LINK/ACT

2

English

3. Configure the Power Over Ethernet (PoE) Switch

Note: It is recommended that you configure the PoE Switch from a wired
computer. Before the PoE Switch can be configured, a Static IP address must
be assigned to your computer's network adapter in the subnet of

192.168.223.x. Since the PoE Switch's default IP address is 192.168.223.100,
make sure no other network devices are assigned an IP address of

192.168.223.100. (Refer to Troubleshooting section on how to configure
TCP/IP settings on your PC.)

Web Browser

1. Open your web browser, type
http://192.168.223.100 in the
Address bar, and then press Enter.

2. Enter the Password, and then click
Apply. By default:

Password: admin

3. Click Configuration and then click
System. Configure the IP

Address, Subnet Mask and
Gateway to match your network
and then click Apply.

Your installation is now complete.

For detailed information regarding the TPE-80WS's configuration and
advanced settings, please refer to the Troubleshooting section, User's
Guide CD-ROM, or TRENDnet's website at http://www.trendnet.com

To ensure the highest level of customer service and support, please take a moment to

register your product Online at: www.trendnet.com/register

Register Your Product

Thank you for choosing TRENDnet

3

English

Troubleshooting

Q1: How do I configure TCP/IP settings on my computer?

1. Go into the Control Panel and double-

click the Network Connections icon,
right-click the Local Area Connection
icon and then click Properties.

2. Click Internet Protocol (TCP/IP) and

then click Properties. Then click on
Use the following IP address, and
make sure you assign your network
adapter an IP address in the subnet of

192.168.223.x.

Q2:

I typed http://192.168.223.100 in my Internet Browser's Address Bar, but an
error message says “The page cannot be displayed.” How can I get into the TPE­80WS's web configuration page?

First, check your hardware settings again by following the instructions in

A2:

section 2. Second, make sure the POWER and LINK/ACT lights are lit. Third,
make sure the TCP/IP settings are configured properly (see Q1). Fourth, since
the PoE Switch’s default IP address is 192.168.223.100, make sure that no other
network devices are assigned an IP address of 192.168.223.100.

Q3:

If my network's IP is different than the PoE Switch's range, what should I do?

A3:

You should still configure the PoE Switch first. After all the settings are
applied, go to the PoE Switch's configuration page, click on IP settings and change
the IP address of the PoE Switch to match your network's IP.

4

My 802.3af Powered device does not power on when I plug the device into

Q4:

the Switch. What should I do?

First, verify that your PoE device supports IEEE 802.3af protocol. Second,

A4:

verify that your PoE device powers up using its power adapter. Third, power cycle
the PoE switch. Unplug power to the switch, wait 15 seconds, then plug the
power back in. Fourth, plug the device into a different port on the PoE switch.
Fifth, try using another Cat-5e cable.

I forgot the administration password. How do I reset my TPE-80WS?

Q5:

Press on the default button using a pen or paperclip for 10 seconds. The

A5:

default password is admin.

What are the default port settings for configuring the Switch through the

Q6:

console port using HyperTerminal?

Bits per Second: 115200; Data bits: 8; Parity: None; Stop bits: 1; Flow control:

A6:

None; Emulation: VT100.

If you still encounter problems or have any questions regarding the TPE-80WS, please
contact TRENDnet’s Technical Support Department.

5

Certifications

This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.

Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.

ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.

TRENDnet Technical Support

.

US Canada

Toll Free Telephone: [phone]

24/7 Tech Support

Europe (Germany France Italy Spain Switzerland UK)

Toll Free Telephone: [phone]

English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET

. . . . .

Worldwide

Telephone: +(31) (0) 20 504 05 35

English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET

Product Warranty Registration

Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register

20675 Manhattan Place
Torrance, CA 90501
USA

Copyright ©2007. All Rights Reserved. TRENDnet.