TRENDnet TEW-810DR User manual

TRENDnet User’s Guide

Cover Page

TRENDnet User’s Guide

Table of Contents

Website Filter .................................................................................................... 22

Inbound Filter .................................................................................................... 22

Table of Contents ............................................................................ 2

ADVANCED ................................................................................... 23

Product Overview ........................................................................... 4

Package Contents .......................................................................................................... 4

Features ......................................................................................................................... 4

Product Hardware Features........................................................................................... 5

Application Diagram ...................................................................................................... 6

Router Setup ................................................................................... 7

Creating a Home Network ............................................................................................. 7

Router Installation ......................................................................................................... 8

Connect additional wired devices to your network ..................................................... 10

Wireless Networking and Security ................................................. 11

How to choose the type of security for your wireless network .................................. 11

Secure your wireless network ..................................................................................... 12

Connect wireless devices to your router ..................................................................... 13

Connect wireless devices using WPS ........................................................................... 14

Basic ............................................................................................. 15

Access your router management page ........................................................................ 15

Network Status ............................................................................................................ 16

Wireless settings .......................................................................................................... 17

Guest Network ............................................................................................................. 18

Steps to improve wireless connectivity ....................................................................... 19

Parental Control ........................................................................................................... 19

Access Control Filters .................................................................... 20

Access control basics ................................................................................................... 20

Service and Port blocking................................................................................... 20

IP blocking .......................................................................................................... 21

Change your router IP address .................................................................................... 23

Set up the DHCP server on your router ....................................................................... 23

Set up DHCP reservation ............................................................................................. 24

Manually configure your Internet connection ............................................................ 25

Manually configure your DNS server setting ............................................................... 25

Manually configure your MTU setting ......................................................................... 26

Clone a MAC address ................................................................................................... 26

Add static routes to your router .................................................................................. 27

Enable RIP on your router ........................................................................................... 27

IPv6 Internet Connection Settings ............................................................................... 28

Prioritize traffic using QoS (Quality of Service) ........................................................... 29

Advanced wireless settings ......................................................................................... 29

Multiple SSID ..................................................................................................... 29

Wireless bridging using WDS (Wireless Distribution System) ........................... 30

Additional wireless settings ............................................................................... 31

Wireless security (Wireless MAC filter) ............................................................. 33

Set your router date and time ..................................................................................... 33

Create schedules ......................................................................................................... 34

Open a device on your network to the Internet .......................................................... 35

DMZ ................................................................................................................... 35

Virtual Server ..................................................................................................... 35

Special Applications ........................................................................................... 36

Gaming............................................................................................................... 37

Enable/disable Application Layer Gateways (ALG) ...................................................... 38

Enable/disable UPnP on your router ........................................................................... 39

Router Maintenance & Monitoring ............................................... 39

TRENDnet User’s Guide

Change your router login password ............................................................................ 39

Change your device name ........................................................................................... 40

Change your device URL .............................................................................................. 40

Identify your network on the Internet ......................................................................... 41

Allow remote access to your router management page ............................................. 42

Reset your router to factory defaults .......................................................................... 42

Router Default Settings ............................................................................................... 43

Backup and restore your router configuration settings .............................................. 43

Upgrade your router firmware .................................................................................... 44

Reboot your router ...................................................................................................... 45

Allow/deny ping requests to your router from the Internet ....................................... 46

Check the router system information .......................................................................... 46

Router Management Page Structure ............................................. 50

Technical Specifications................................................................. 51

Appendix ...................................................................................... 54

Table of contents

Troubleshooting ............................................................................ 53

TRENDnet User’s Guide

Product Overview

networks—a high speed 433 Mbps Wireless AC network and a 300 Mbps Wireless N network to connect common wireless devices.

TEW-810DR

Ease of Use

Easy Setup

Get up and running in minutes with the intuitive guided setup One Touch Connection Securely connect to the router at the touch of the Wi-Fi Protected Setup

(WPS) button

Security

Encrypted Wireless

For your security the router arrives pre-encrypted with its own unique password

TEW-810DRU

Package Contents

In addition to your router, the package includes:

• CD-ROM (Utility and User’s Guide)

• Multi-Language Quick Installation Guide

• Network cable Ethernet Cable (1.5m / 5ft.)

• Power Adapter (12V, 1A)

If any package contents are missing or damaged, please contact the retail store, online retailer, or reseller/distributor from which the product was purchased.

Features

Guest Network Create a secure, isolated network for guest internet access only Parental Controls

Control access to specific websites or types of content

Performance

Next Generation Wireless AC

802.11ac provides uninterrupted HD video streaming in a busy connected home

Simultaneous Dual Band

High speed 433 Mbps Wireless AC band + 300 Mbps Wireless N

Designed to handle multiple HD streams in a busy connected home, TRENDnet’s AC750 Dual Band Wireless Router, model TEW-810DR, creates two concurrent wireless

Ethernet Ports

Ethernet ports maintain high performance network connections

Reset Button

Internet Port

Power Port

WPS Button

On/Off Power Switch

TRENDnet User’s Guide

Backward Compatible

Compatible with Wireless N and older Wireless G devices

Energy Savings

Product Hardware Features

Rear View

TEW-810DR

Embedded GREENnet technology reduces power consumption by up to 50%

IPv6

IPv6 network support

*For maximum performance of up to 433 Mbps use with at least a 433 Mbps 802.11ac wireless adapter. Maximum wireless signal rates are referenced from IEEE 802.11 theoretical specifications. Actual data throughput and coverage will vary depending on interference, network traffic, building materials and other conditions

• LAN Ports 1-4: Connect Ethernet cables (also called network cables) from your

router LAN ports to your wired network devices.

• Internet Port: Connect an Ethernet cable from your router Internet port to your

modem.

• Reset Button: Press and hold this button for 10 seconds to reset the router.

• On/Off Power Switch: Push the router On/Off power switch to turn your router

“On” (Inner position) or “Off” (Outer position).

• Power Port: Connect the included power adapter from your router power port and

to an available power outlet.

• WPS Button (Wi-Fi Protected Setup): Push and hold this button for 5 seconds to

activate WPS. The Power LED will blink when WPS is activated.

LAN Ports 1-4

Power LED

TRENDnet User’s Guide

Front View

Power/WPS LED: The indicator is solid green when your router is powered on.

Otherwise if this LED indicator is off, there is no power to your router. The indicator will also blink when WPS is activated. The LED will stop blinking and remain solid green automatically once WPS process is completed.

Internet Port (Link/Activity) LED – This LED indicator is solid green when your router Gigabit Internet port is physically connected to the modem network or Ethernet port with a network or Ethernet cable (modem turned on). The LED indicator will be blinking green while data is transmitted or received through the Gigabit Internet port of your router.

Application Diagram

Internet LED

The router is installed near the modem (typically supplied by your ISP “Internet Service Provider”) and physically connected to it from the router’s Internet port to the modem’s network port which connects to the Internet. 2.4GHz wireless signals from the router are broadcasted to wireless clients such as laptops (with wireless capability) and the less congested 5GHz wireless signals from the router are broadcasted to other wireless client devices such as TVs, game consoles, or media bridges thereby providing Internet access for all wireless client devices.

TEW-810DR

TRENDnet User’s Guide

Router Setup

Creating a Home Network

What is a network?

A network is a group of computers or devices that can communicate with each other. A home network of more than one computer or device also typically includes Internet access, which requires a router.

A typical home network may include multiple computers, a media player/server, a printer, a modem, and a router. A large home network may also have a switch, additional routers, access points, and many Internet-capable media devices such as TVs, game consoles, and Internet cameras.

• Modem – Connects a computer or router to the Internet or ISP (Internet Service

Provider).

• Router – Connects multiple devices to the Internet.

• Switch –Connect several wired network devices to your home network. Your

router has a built-in network switch (the LAN port 1-4). If you have more wired network devices than available Ethernet ports on your router, you will need an additional switch to add more wired connections.

How to set up a home network

1. For a network that includes Internet access, you’ll need:

• Computers/devices with an Ethernet port (also called network port) or wireless

networking capabilities.

• A modem and Internet service to your home, provided by your ISP (modem

typically supplied by your ISP).

• A router to connect multiple devices to the Internet.

2. Make sure that your modem is working properly. Your modem is often provided by your Internet Service Provider (ISP) when you sign up for Internet service. If your modem is not working contact your ISP to verify functionality.

3. Set up your router. See “How to setup your router” below.

4. To connect additional wired computers or wired network devices to your network, see “Connect additional wired devices to your network

5. To set up wireless security on your router, see “Wireless Networking and Security” on page 11.

How to setup your router

Refer to the Quick Installation Guide or continue to the next section “

Installation” on page 8 for more detailed installation instructions.

Where to find more help

In addition to this User’s Guide, you can find help below:

• http://www.trendnet.com/support

available from this Web page)

(documents, downloads, and FAQs are

” on page 10.

TEW-810DR

Router

TRENDnet User’s Guide

Router Installation

Before you Install

Many Internet Service Providers (ISPs) allow your router to connect to the Internet without verifying the information fields listed below. Skip this section for now and if your router cannot connect to the Internet using the standard installation process, come back to this page and contact your ISP to verify required ISP specification fields listed below.

1. Obtain IP Address Automatically (DHCP)

Host Name (Optional) MAC Address: ___:___:___:___:___:___ Enter your PC’s MAC address (Optional) DNS Servers Address 1: _____. _____._____._____ (Optional) DNS Servers Address 2: _____. _____._____._____ (Optional)

2. Static/Fixed IP address

MAC Address: ___:___:___:___:___:___ Enter your PC’s MAC address (Optional) IP Address: _____. _____._____._____ (e.g. 215.24.24.129) Subnet Mask: _____. _____._____._____ Default Gateway IP Address: _____. _____._____._____ DNS Servers Address 1: _____. _____._____._____ DNS Servers Address 2: _____. _____._____._____

3. PPPoE to obtain IP automatically

User Name: _________ Password: ________________

4. PPTP

Type (Dynamic IP/DHCP or Static IP) PPTP Server: _____________________ (IP address) IP Address: _____. _____._____._____ (e.g. 215.24.24.129) Subnet Mask:_____. _____._____._____ Default Gateway:_____. _____._____._____ Server IP: _____. _____._____._____ DNS Servers Address 1: _____. _____._____._____ DNS Servers Address 2: _____. _____._____._____ User Name: _________ Password: ________________

5. L2TP

Type (Dynamic IP/DHCP or Static IP) L2TP Server: _____________________ (IP address) IP Address: _____. _____._____._____ (e.g. 215.24.24.129) Subnet Mask:_____. _____._____._____ Default Gateway:_____. _____._____._____ Server IP: _____. _____._____._____ DNS Servers Address 1: _____. _____._____._____ DNS Servers Address 2: _____. _____._____._____ User Name: _________ Password: ________________

TEW-810DR

TRENDnet User’s Guide

Hardware Installation

1. Verify that you have an Internet connection when connecting your computer directly to your modem.

2. Turn off your modem.

3. Disconnect the Network cable from your computer to your modem.

4. Connect your modem to the router Internet port (yellow).

5. Connect your computer to one of the router LAN ports.

Internet Setup Wizard

TEW-810DR

1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and the installation wizard will automatically open. If the wizard does not appear, type

http://tew-810dr into the address bar of your web browser and press enter. Enter

your User Name and Password, click Login and then click Advanced > Setup > Wizard.

Note: You can also access the device using the default IP address

(http://192.168.10.1).

6. Connect the power adapter to the router and then to a power outlet.

7. Press the power on / off switch of the router and turn on your modem.

8. Verify that the status LED indicators on the front of the router are illuminated: Power, Internet.

2. Select your language and click next to start the installation wizard.

TRENDnet User’s Guide

3. The router will detect your internet connection type.

TEW-810DR

Connect additional wired devices to your network

You can connect additional computers or other network enabled devices to your network by using Ethernet cables to connect them to one of the available LAN ports labeled 1,2,3,4 on your router. Check the status of the LED indicators (1, 2, 3, or 4) on

4. Once complete the installation wizard is completed, the wizard will display your router’s settings. Click Save to apply settings and continue. Click Print if you would like to print your settings for future reference.

2. Select your language and click next to start the installation wizard.

5. Open a different web browser window to verify you have Internet connection.

6. For added security, the router is pre-encrypted with its own unique wireless network security key. You can find the unique network security key and pre-assigned network name (SSID) on a sticker on the front of the router and on a label on the bottom of the router. If you would like to change the wireless settings, continue to the next page to launch the wireless setup wizard.

the front panel of your router to ensure the physical cable connection from your computer or device.

Note: If you encounter issues connecting to your network, there may be a problem with your computer or device network settings. Please ensure that your computer or device network settings (also called TCP/IP settings) are configured to obtain IP address settings automatically (also called dynamic IP address or DHCP) and to Obtain DNS Server address settings automatically.

Security Standard

WEP

WPA

WPA2

Standards

using this standard)

IEEE 802.11a/b/g

standard)

IEEE 802.11a/b/g/n

Highest

Setting

Up to 54Mbps

(11ac)*

Encryption Strength

Low

Medium

High

Open System or

Different key sizes

TKIP

8-63 characters

AES

8-63 characters

300Mbps, 450Mbps, 867Mbps, or 1.3Gbps)

TRENDnet User’s Guide

Wireless Networking and Security

How to choose the type of security for your wireless network

Setting up wireless security is very important. Leaving your wireless network open and unsecure could expose your entire network and personal files to outsiders. TRENDnet recommends reading through this entire section and setting up wireless security on your new router. There are a few different wireless security types supported in wireless networking each having its own characteristics which may be more suitable for your wireless network taking into consideration compatibility, performance, as well as the security strength along with using older wireless networking hardware (also called legacy hardware). It is strongly recommended to enable wireless security to prevent unwanted users from accessing your network and network resources (personal documents, media, etc.). In general, it is recommended that you choose the security type with the highest strength and performance supported by the wireless computers and devices in your network. Please review the security types to determine which one you should use for your network.

Wireless Encryption Types

• WEP: Legacy encryption method supported by older 802.11b/g hardware. This is

the oldest and least secure type of wireless encryption. It is generally not recommended to use this encryption standard, however if you have old 802.11 b or

802.11g wireless adapters or computers with old embedded wireless cards(wireless clients), you may have to set your router to WEP to allow the old adapters to connect to the router.

Note: This encryption standard will limit connection speeds to 54Mbps.

• WPA: This encryption is significantly more robust than the WEP technology. Much

of the older 802.11g hardware was been upgraded (with firmware/driver upgrades) to support this encryption standard. Total wireless speeds under this encryption type however are limited to 54Mbps.

• WPA-Auto: This setting provides the router with the ability to detect wireless

devices using either WPA or WPA2 encryption. Your wireless network will automatically change the encryption setting based on the first wireless device connected. For example, if the first wireless client that connects to your wireless network uses WPA encryption your wireless network will use WPA encryption. Only

when all wireless clients disconnect to the network and a wireless client with WPA2 encryption connects your wireless network will then change to WPA2 encryption.

Note: WPA2 encryption supports 802.11n speeds and WPA encryption will limit your connection speeds to 54Mbps

• WPA2: This is the most secure wireless encryption available today, similar to WPA

encryption but more robust. This encryption standard also supports the highest connection speeds. TRENDnet recommends setting your router to this encryption standard. If you find that one of your wireless network devices does not support WPA2 encryption, then set your router to either WPA or WPA-Auto encryption.

Note: Check the specifications of your wireless network adapters and wireless appliances to verify the highest level of encryption supported. Below is brief

comparison chart of the wireless security types and the recommended configuration depending on which type you choose for your wireless network.

IEEE 802.11a/b/g (802.11n devices

Compatible Wireless

Performance Under This

Additional Options

Recommended Configuration

*Dependent on the maximum 802.11n/ac data rate supported by the device (150Mbps,

will operate at

802.11g to connect

Shared Key, HEX or ASCII,

Open System ASCII 13 characters

(802.11n devices will operate at

802.11g to connect using this

TKIP or AES, Preshared Key or RADIUS

Preshared Key

TEW-810DR

Up to 450Mbps (11n) and up to 1.3Gbps

TKIP or AES, Preshared Key or RADIUS

Preshared Key

TRENDnet User’s Guide

Secure your wireless network

Wireless (2.4GHz or 5GHz)> Security

After you have determined which security type to use for your wireless network (see “How to choose the security type for your wireless network wireless security.

1. Log into your router management page (see “Access your router management page on page 16).

2. Click on the Wireless button.

3. Underneath the basic wireless band section, you will see Security Mode. Click on the drop-down list to select your wireless security type.

Note: It is recommended to use WEP-OPEN because it is known to be more secure than Shared Key.

” on page 11), you can set up

”

• Current Network Key - You can define up to 4 keys however, only one key can be

active at any given time. Most users simply define one key. Click the drop-down list to select which of the 4 keys is the active key.

• Network Key 1-4 o This is where you enter the WEP key needed for a computer to connect to the

router wirelessly

o You can define up to 4 passwords or 4 keys. Only one key can be active at a given

time. Most users simply define one key.

o Choose a key index 1, 2, 3, or 4 and enter the key. o When connecting to the router, the client must match both the password and the

Key number. (e.g. if you have activated Key 2 with a password of 12345, then the client must select: Key 2 (entering Key 1, 3, or 4 will block the ability to connect) and enter password 12345)

TEW-810DR

WEP Key Format

Selecting WEP-OPEN, WEP-SHARED:

If selecting WEP (Wired Equivalent Privacy), please review the WEP settings to configure and click Apply to save the changes.

Note: WEP security is only available in the Security Mode list when 802.11 n-mode is set to Off under Wireless (2.4GHz or 5GHz) > Basic.

Note: WPS functionality is not available when using WEP.

In the Security Mode drop-down list, select WEP-OPEN or WEP-SHARED.

Character set 0-9 & A-F, a-f only Alphanumeric (a,b,C,?,*, /,1,2, etc.)

64-bit key length 10 characters 5 characters

128-bit key length 26 characters 13 characters

Note: It is recommended to use 128-bit format because it is more secure to use a key that consists of more characters.

• Click here to display - Typically, the password characters are masked for security

purposes. This link displays actual characters of the currently assigned password for your reference.

HEX ASCII

TRENDnet User’s Guide

Selecting WPA-PSK, WPA2-PSK, WPA2-PSK, or Mixed (WPA2-PSK recommended):

In the Security Mode drop-down list, select WPA-.

The following section outlines options when selecting WPA-PSK, WPA2-PSK, or WPA2- PSK Mixed (Preshared Key Protocol),

• WPA Encryption: Select a Cipher Type to use. When selecting WPA-PSK security, it

is recommended to use TKIP + AES.

o When selecting WPA2-PSK Mixed security, it is recommended to use TKIP+AES. o When selecting WPA2-PSK security, it is recommended to use AES.

• WPA passphrase: Enter the passphrase.

o This is the password or key that is used to connect your computer to this router

wirelessly

Note: 8-63 alphanumeric characters (a,b,C,?,*, /,1,2, etc.)

• Network Key Rotation Interval: Enter the time interval (seconds) of when the

network passphrase will rotate. Note: It is recommended to use the default

interval time. Your passphrase will not change, rotation of the key is part of the WPA protocol and designed to increase security.

Selecting WPA, WPA2, or WPA2 Mixed:

The following section outlines options when selecting WPA. WPA2 or WPA2 Mixed known as EAP (Extensible Authentication Protocol). Also known as called Remote Authentication Dial-In User Service or RADIUS.

Note: This security type requires an external RADIUS server, PSK only requires you to create a passphrase.

• RADIUS Server: Enter the IP address of the RADIUS server. (e.g. 192.168.10.250)

• RADIUS Port: Enter the port your RADIUS server is configured to use for RADIUS

authentication.

Note: It is recommended to use port 1812 which is typical default RADIUS port.

• RADIUS Key: Enter the shared secret used to authorize your router with your

RADIUS server.

Connect wireless devices to your router

A variety of wireless network devices can connect to your wireless network such as:

• Gaming Consoles

• Internet enabled TVs

• Network media players

• Smart Phones

• Wireless Laptop computers

• Wireless IP cameras

Each device may have its own software utility for searching and connecting to available wireless networks, therefore, you must refer to the User’s Manual/Guide of your wireless client device to determine how to search and connect to this router’s wireless network.

See the “Appendix network.

” on page 54 for general information on connecting to a wireless

TEW-810DR

TRENDnet User’s Guide

Connect wireless devices using WPS

WPS (Wi-Fi Protected Setup) is a feature that makes it easy to connect devices to your wireless network. If your wireless devices support WPS, you can use this feature to easily add wireless devices to your network.

Note: You will not be able to use WPS if you set the SSID Broadcast setting to Disabled or if you are using WEP security.

There are two methods the WPS feature can easily connect your wireless devices to your network.

• Push Button Configuration (PBC) method o (RECOMMENDED) Hardware Push Button method–with an external button

located physically on your router and on your client device

o WPS Software/Virtual Push Button - located in router management page

• PIN (Personal Identification Number) Method - located in router management page

Note: Refer to your wireless device documentation for details on the operation of WPS.

Recommended Hardware Push Button (PBC) Method

• Note: It is recommended that a wireless key (passphrase or password) is created

before connecting clients using the PBC method. If no wireless key is defined when connecting via PBC, the router will automatically create an encryption key that is 64 characters long. This 64 character key will then have to be used if one has to connect computers to the router using the traditional connection method.

To add a wireless device to your network, simply push the WPS button on the wireless device you are connecting (consult client device User’s Guide for length of time), then push and hold the WPS button located on your router for 3 seconds and release it. A blue LED on your router WPS button will flash indicating that the WPS setup process has been activated on your router. (See “Product Hardware Features

For connecting additional WPS supported devices, repeat this process for each additional device.

PBC (Software/Virtual Push Button)

Wireless (2.4GHz or 5GHz)> WPS

In addition to the hardware push button located physically on your router, the router management page also has push button which is a software or virtual push button you can click to activate WPS on your router.

1. Log into your router management page (see “Access your router management page on page 16).

2. Click on the Advanced tab.

3. Select wireless band you would like to configure, Wireless 2.4GHz or Wireless 5GHz and click on WPS.

4. To add a wireless device to your network, simply click the Add Enrollee button in the router management page, then push the WPS button on the wireless device (consult wireless device’s User’s Guide for length of time) you are connecting.

” on page 5)

TEW-810DR

”

TRENDnet User’s Guide

PIN (Personal Identification Number)

Wireless (2.4GHz or 5GHz)> WPS

If your wireless device has WPS PIN (typically an 8-digit code printed on the wireless device product label or located in the wireless device wireless software utility), you can use this method.

1. Log into your router management page (see “Access your router management page on page 15).

2. Click on the Advanced tab.

3. Select wireless band you would like to configure, Wireless 2.4GHz or Wireless 5GHz and click on WPS.

Basic

Access your router management page

Note: Your router management page URL/domain name http://tew-810dr or IP address

http://192.168.10.1 is accessed through the use of your Internet web browser (e.g.

Internet Explorer, Firefox, Chrome, Safari, Opera) and will be referenced frequently in

”

this User’s Guide.

1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and go to URL/domain name http://tew-810dr or IP address http://192.168.10.1 router will prompt you for a user name and password.

2. For added security, the router is preconfigured with a unique password. You can find the Password on a sticker on the side of the router and on the label on the bottom of the router.

TEW-810DR

. Your

4. Next to Station PIN, enter the WPS PIN of the wireless device you are connecting and click the Add Enrollee button.

Note: You may need to initiate the WPS PIN on your wireless device first when using this method. Refer to your wireless device documentation for details on the operation of WPS.

3. Enter your Username and Password, select your preferred language, then click Login.

TRENDnet User’s Guide

• User Name: admin

• Password: (xxxxxxxx)

Note: User Name and Password are case sensitive.

Network Status

This screen appears when you login into your router. This section provides an over view of your router.

Internet: This icon turns green to indicate that your network has a valid Internet connection. Amber color indicates a physical connection on the Internet port of the router but with no valid Internet connection. Red color indicates disconnected Internet port.

Guest Network: The section provides your router’s guest network SSID. This icon turns green to indicate when your router’s wireless network is enabled. Red color indicates your router’s wireless network is disabled.

Wireless: This icon turns green to indicate when your router’s wireless network is enabled. Red color indicates your router’s wireless network is disabled.

Security: This section provides your router’s wireless network security information.

Connected Devices: This section provides information of all connected devices on your router.

TEW-810DR

TRENDnet User’s Guide

Wireless settings

Wireless (2.4GHz or 5GHz)> Basic

This section outlines available management options under basic wireless sub tab for both 2.4GHz and 5GHz wireless sections.

1. Log into your router management page (see “Access your router management page on page 15).

2. Click on Wireless and under the Basic tab.

3. To save changes to this section, click Apply when finished.

• Radio On/Off:

o On: Turns on wireless radio. o Off: Turns off wireless radio. o Schedule: Select the schedule rule you would like to apply to your wireless

network. (See “Create Schedule

• Wireless Mode

o Auto: Select this option if you have non-802.11n wireless clients (802.11a/b/g)

connecting to your wireless network.

o Off: The router will operate in 802.11n mode only, non-802.11n wireless clients

will not be able to connect when this option is selected.

When applying the 802.11 n-mode setting on 2.4GHz, please keep in mind the following:

• Wireless devices that support 802.11n are backwards compatible and can connect

wirelessly at 802.11g or 802.11b.

” section on page 34).

• Connecting at 802.11b or 802.11g will limit the capability of your 802.11n

supported wireless devices from obtaining higher performance and data rates.

• Allowing 802.11b or 802.11g devices to connect to an 802.11n capable wireless

network may degrade the wireless network performance below the higher performance and data rates of 802.11n.

• Wireless devices that only support 802.11b or 802.11g will not be able to connect

”

to a wireless network that is set to 802.11n only mode.

• Wireless devices that only support 802.11b will not be able to connect to a wireless

network that is set to 802.11g only mode.

• Wireless Name (SSID): Enter the wireless name (SSID) for your wireless network.

This acronym stands for Service Set Identifier and is the name of your wireless network. It differentiates your wireless network from others around you. By default, the router’s wireless name is unique to the device. If you choose to change the SSID, change it to a name that you can easily remember.

• Broadcast Network Name (SSID):

o Enabled allows wireless devices to search and discover your wireless network

name (also called SSID) broadcasted by your router.

o Disabled turns off the ability for wireless devices to find your network. It is still

possible for wireless devices to be configured to connect to your wireless network. Disabling this setting will disable WPS functionality.

• Frequency (Channel): To manually set the channel on which the router will

broadcast, click the drop-down list and select the desired Channel for wireless communication. The goal is to select the Channel that is least used by neighboring wireless networks.

• Channel Bandwidth: Select the appropriate channel width for your wireless

network. This setting only applies to 802.11n and 802.11ac. For greater 802.11n performance in 2.4GHz, select 40MHz (Options: 20MHz or 40MHz). For greater

802.11ac performance in 5GHz, select 80MHz (Options: 20MHz, 40MHz, or 80MHz) It is recommended to use the default channel bandwidth settings.

Note: Please note that this setting may provide more stability than the higher channel bandwidth settings such as 40 MHz or 80MHz for connectivity in busy wireless environments where there are several wireless networks in the area.

o 20 MHz: This mode operates using a single 20MHz channel for wireless devices

connecting at 802.11n on both 2.4GHz and 5GHz. This setting may provide more stability than 40MHz or 80MHz for connectivity in busy wireless environments where there are several neighboring wireless networks in the area.

o Auto 20/40 MHz (2.4GHz wireless) or Auto 20/40/80 MHz (5GHz wireless):

When 40MHz or 80MHz is active, this mode is capable of providing higher

TEW-810DR

TRENDnet User’s Guide

performance only if the wireless devices support the channel bandwidth settings. Enabling 40MHz or 80MHz typically results in substantial performance increases when connecting an 802.11n or 802.11ac client. Note: Please note that 80MHz

channel bandwidth is only available for 802.11ac 5GHz.

Guest Network

Wireless (2.4GHz or 5GHz) > Guest Network

Creating an isolated and separate wireless guest network (2.4GHz or 5GHz) allows wireless clients to connect to your network for Internet access only and keep your local LAN network safe by restricting guest access to your LAN network resources such as shared documents and media files on your computers, network storage, and printers.

1. Log into your router management page (see “Access your router management page on page 15).

2. Click on the Basic tab.

3. Click on Guest Network section.

4. Review the Guest Network settings, click Apply when finished.

• Radio On/Off:

o On: Turns on wireless radio. o Off: Turns off wireless radio. o Schedule: Select the schedule rule you would like to apply to your wireless

network. (See “Create Schedule

• Wireless Name (SSID): This acronym stands for Service Set Identifier and is the

name of your wireless network. It differentiates your wireless network from others around you. It is recommended to use a different name from your primary wireless network to a name that you can easily identify and differentiate from the primary. You can reference your guests to access this network instead of the primary.

• WLAN Partition: Enabling this option will restrict guests from communicating with

each other over the guest network such as share files.

• Internet Access Only: By default, the option is checked to allow guests to only

”

access the Internet and restrict access to your local LAN network. Please note that unchecking this option will open access to local LAN network to guests.

5. Apply wireless security to your guest network (see “

security for your wireless network” on page 11).

” section on page 34).

How to choose the type of

TEW-810DR

+ 41 hidden pages