TRENDnet TEG-PCBUSR User Manual

FCC Warning

This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Table Of Contents

INTRODUCTION ................................................................... 1

GENERAL DESCRIPTION ......................... .......................... .... 1

LED INDICATORS ................................................................. 1

SUMMARY OF FEATURES ...................................................... 2

CARD INSERTION AND REMOVAL ................................... 3

CARD INSERTION ................. ........................ ........................ 3

[1] Insert the 32-bit CardBus 10/100/1000Mbps Gigabit

Ethernet PC Card ........................................ .. .. .. ... .. .. .. ... . 3

[2] Connect to the Network Media ................................. 4

CARD REMOVAL ................................................................... 4

DRIVER INSTALLATION ........... ... .. .. .. .. ... .. .. .. ... .. .. .. ... .. .. .. ... . 5

DIAGNOSTIC UTILITY FOR WINDOWS ............................. 6

WINDOWS UTILITY INSTALLATION .......................................... 6

CONFIGURATION THE PC CARD ............................................ 7

TECHNICAL SPECIFICATIONS ........................................ 18

VCCI Mark Warning

Introduction

General Description

The 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card is a credit-card sized Fast Ethernet adapter for connecting a notebook to an IEEE 802.3 Ethernet network, IEEE 802.3u fast Ethernet and IEEE 802.3ab Gigabit Ethernet network, it’s designed to work with notebooks or handheld computers that with CardBus slots. Inside its compact package, the 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card holds the Gigabit Ethernet controller, network processing interface, RAM for the data buffer a, 68-pin PC Card plug and RJ-45 10/100/1000Mbps Gigabit Ethernet port. It requires no pre-installation setup -simply insert the PC Card into the computer's 32-bit CardBus slot.

LED Indicators

1. Link/Activity (Link/ACT) ¾ This indicator lights green when the RJ-45 port is

connected to a Ethernet network, if the indicator blinking green will be transmissing/received data to/from the Ethernet network.

2. Link Speed Indicator ¾ The indicator lights green when the port is

connected to 1000Mbps Gigabit Ethernet Network and the indicator lights amber when the port is connected to 100Mbps Fast Ethernet Network. Otherwise, this indicator remains off when the port is connected to a 10Mbps Ethernet Network.

(SPEED)

Summary of Features

The 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card provides the following features:

¾ Complies with IEEE 802.3 10BASE-T Ethernet standard ¾ Complies with IEEE 802.3u 100BASE-TX Fast Ethernet

standard

¾ Complies with IEEE 802.3ab 1000BASE-T Gigabit

Ethernet standard

¾ Complies with ANSI / IEEE 802.3 Auto-Negitiation

standard

¾ Complies with 32-bit CardBus Standard ¾ Supports Crossover Detection & Auto-Correction ¾ Built-in Transmit/Reveive FIFO data buffer (8K/64K) ¾ No manual setup switches -- automatically configured by

software

¾ Low power consumption ¾ Supported driver list:

 Microsoft Windows Vista (32/64bit)  Microsoft Windows XP (32/64bit)  Microsoft Windows 2000 / ME / 98SE  Microsoft Network Client for DOS (NDIS 2 driver)  NetWare Client for DOS (ODI driver)

Card Insertion and Removal

Card Insertion

Follow these steps to install the 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card:

[1] Insert the 32-bit CardBus 10/100/1000Mbps Gigabit

Ethernet PC Card

Find/select an available Type II or Type III 32-bit PC Card slot on your notebook’s side or rear panel. Holding the 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card with the LED indicator facing up then insert to the 32-bit PC Card slot. Slide the 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card all the way into the 32-bit PC Card slot until it reaches a firm stop.

[2] Connect to the Network Media

Simply plug one end of the cable (RJ-45 connector) into an available hub/switch port, and plug the other end (RJ-45 connector) into the RJ-45 port of your 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card.

Card Removal

Use the computer's PC Card Eject mechanism to unseat the 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card from the computer's PC Card slot. The PC Card will then protrude from the PC Card slot and you can easily remove the PC Card by gripping its protruding end and withdrawing it from the PC Card receptacle.

+ 9 hidden pages