TRENDNET TE100-S16g, TE100-S24g User Manual [fr]

16-Port 10/100Mbps GREENnet Switch (TE100-S16g)
24-Port 10/100Mbps GREENnet Switch (TE100-S24g)

ŸGuide d'installation rapide (1)

ŸTechnical Specifications (4)

ŸTroubleshooting (5)

1.02

1. Avant de commencer

Contenu de l'emballage

ŸTE100-S16g / TE100-S24g
ŸGuide d'installation rapide en plusieurs langues

Ÿ

Cordon de secteur

Ÿ

Kit de montage

Si tout le contenu ci-dessus sont manquantes, s'il vous plaît contactez votre
revendeur.

Configuration minimale

ŸUn ordinateur avec un adaptateur réseau correctement installé
ŸCâble Cat. 5, Cat. 5e ou Cat. 6 pour réseaux

La surface doit supporter au moins 1.86 kg pour le Switch

Ÿ

La prise secteur doit être située à un maximum de 1,82 mètres du Switch

Ÿ

Inspectez visuellement la prise d'alimentation et assurez-vous qu'elle est

Ÿ

correctement connectée à l'adaptateur secteur
Vérifiez la présence d'une source de ventilation adéquate autour du Switch

Ÿ

pour une dissipation efficace de la chaleur
Ne placez pas d'objets lourds sur le Switch

Ÿ

2. Installation du matériel

1. Branchez le Cordon de secteur au TE100-S16g/ TE100-S24g ainsi qu’à une

prise de courant.

1

2. Branchez un câble réseau Cat. 5, Cat. 5e ou Cat. 6 RJ-45 de l'ordinateur vers
un port Ethernet disponible du .TE100-S16g/TE100-S24g

Montage du rack

Le boîtier peut être installé dans un rack EIA standard de 19 pouces qui peut
être placé dans une armoire de répartition avec les autres équipements.

1. Attachez les supports de montage des deux côtés du switch et fixez-les avec
les vis fournies.

2. Installez soigneusement le switch dans le rack. Alignez le support sur les
trous des vis du rack et utilisez les vis fournies avec le matériel pour installer
le switch.

2

3. LEDs

Alimentation

ŸVert : Sous tension
ŸEteint : Hors tension

Link/ACT

ŸVert (Fixe) : Relié à un autre périphérique
ŸVert (Clignotant) : Activité depuis cette liaison
ŸEteint : Rien n'est détecté sur le port

100Mbps

ŸVert : la connexion du port est de 100/200Mbps (Half/Full)
ŸEteint : la connexion pour le port est de 10/20Mbps (Half/Full) ou rien n'est

détecté sur le port

3

Technical Specifications

Standards

ŸIEEE 802.3 10BASE-T
ŸIEEE 802.3u 100BASE-TX
ŸIEEE 802.3x Flow Control

Network Media

ŸEthernet: 2-Pair UTP/STP Cat. 3, -4, -5
ŸFast Ethernet: 2-Pair UTP/STP Cat. 5, -5e , -6

Data Transfer Rates

ŸEthernet: 10Mbps (half-duplex), 20Mbps (full-duplex)
ŸFast Ethernet: 100Mbps (half-duplex),

200Mbps (full-duplex)

Interface

ŸTE100-S16g: 16 x 10/100/1000 Auto-MDIX RJ-45 ports
ŸTE100-S24g: 24 x 10/100/1000 Auto-MDIX RJ-45 ports

Data RAM Buffer

ŸTE100-S16g: 1.25Mbits per device
ŸTE100-S24g: 1.25Mbits per device

Hardware

Packet Filtering/
Forwarding Rate

Ÿ10Mbps Ethernet: 14,880pps (packets per second)
Ÿ100Mbps Fast Ethernet: 148,800pps

Protocol/Topology CSMA/CD / Star

Filtering Table

MAC Address Learning

Switch Fabric

Power Consumption

Automatic Update
8K entries per device

ŸTE100-S16g: 3.2Gbps Forwarding Capacity
ŸTE100-S24g: 4.8Gbps Forwarding Capacity

ŸTE100-S16g: 6W (max)
ŸTE100-S24g: 6.4W (max)

Diagnostic LEDs

Power, Link/ACT, 100Mbps

Power

100-240VAC, 50/60Hz, Internal Power Supply

Dimensions

440 x 140 x 40 mm (17.32 x .5.51 x 1.57 in.)

Certifications FCC, CE

Weight

ŸTE100-S16g: 1.72kg (3.8 lb)
ŸTE100-S24g: 1.86kg (4.1 lb)

Temperature

ŸOperating: 0° ~ 40° C (32° ~ 104° F)
ŸStorage: -10° ~ 70° C (14° ~ 158° F)

Humidity

ŸOperating: 10% ~ 90%
ŸStorage: 5% ~ 90%

4

Troubleshooting

1. After connecting the Switch to a power outlet, the LEDs do not turn on.

1.

Check the connection of the power cord to the TE100-S16g/TE100-S24g
and the power outlet.

2. Check that the power outlet is receiving power.

2. When I connect a computer to the Switch's port, the Link/ACT LED turns

on, but the 100Mbps LED remains off.

When the 100Mbps LED is off, the computer's connection speed is
10Mbps.

3. After I connect my PCs to the Switch, I am unable to share files.

1. Check the LEDs on the Switch. Make sure the Link/ACT LED is on.

2. Check the network cable. The minimum length of the cable is 1.5 meters
and the maximum length of the cable is 100 meters.

3. Disable any software firewall program.

4. Verify that you have file sharing enabled. Please contact your Operating
System support for more information.

4. After I connect my PCs to the Switch, I can only get onto the Internet
from one computer.

The Switch was not designed to share Internet between multiple
computers. You need to get an Internet router such as the
TW100-S4W1CA.

5. Where is the uplink port located on the Switch?

Since all the ports on the Switch are Auto-MDIX, any of the ports can be
used as an uplink port.

If you still encounter problems or have any questions regarding the
TE100-S16g/ TE100-S24g please contact TRENDnet's Technical Support
Department.

5

Limited Warranty

TRENDnet warrants its products against defects in material and workmanship, under
normal use and service, for the following lengths of time from the date of purchase.

AC/DC Power Adapter, Cooling Fan and Power Supply carry 1 year warranty

If a product does not operate as warranted during the applicable warranty period,
TRENDnet shall reserve the right, at its expense, to repair or replace the defective
product or part and deliver an equivalent product or part to the customer. The
repair/replacement unit's warranty continues from the original date of purchase. All
products that are replaced become the property of TRENDnet. Replacement products
may be new or reconditioned. TRENDnet does not issue refunds or credit. Please
contact the point-of-purchase for their return policies.

TRENDnet shall not be responsible for any software, firmware, information, or memory
data of customer contained in, stored on, or integrated with any products returned to
TRENDnet pursuant to any warranty.

There are no user serviceable parts inside the product. Do not remove or attempt to
service the product by any unauthorized service center. This warranty is voided if (i) the
product has been modified or repaired by any unauthorized service center, (ii) the product
was subject to accident, abuse, or improper use (iii) the product was subject to conditions
more severe than those specified in the manual.

Warranty service may be obtained by contacting TRENDnet within the applicable
warranty period and providing a copy of the dated proof of the purchase. Upon proper
submission of required documentation a Return Material Authorization (RMA) number
will be issued. An RMA number is required in order to initiate warranty service support for
all TRENDnet products. Products that are sent to TRENDnet for RMA service must have
the RMA number marked on the outside of return packages and sent to TRENDnet
prepaid, insured and packaged appropriately for safe shipment. Customers shipping
from outside of the USA and Canada are responsible for return shipping fees. Customers
shipping from outside of the USA are responsible for custom charges, including but not
limited to, duty, tax, and other fees.

WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE
AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT
TRENDNET'S OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES
AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES,

TE100-S16g/TE100-S24g

- 3 Year Limited Warranty

EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW,
STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES
NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR
USE OF TRENDNET'S PRODUCTS.

TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES
NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S
MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED
ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE
OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER
HAZARD.

LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET
ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER
BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND,
OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONN ECTION WITH THE SALE , INSTALLATION, MAINTE NANCE, USE,
PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH
DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND
OF THE PURCHASE PRICE PAID, AT TRENDNET'S OPTION. THIS DISCLAIMER OF
LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED
HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.

Governing Law: This Limited Warranty shall be governed by the laws of the state of
California.

Some TRENDnet products include software code written by third party developers.
These codes are subject to the GNU General Public License ("GPL") or GNU Lesser
General Public License ("LGPL").

Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section and
look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These
codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the
developers. TRENDnet does not provide technical support for these codes. Please go to
http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.txt for specific
terms of each license.

TRENDnet

20675 Manhattan Place

Torrance, CA 90501. USA

Copyright ©2011. All Rights Reserved. TRENDnet.