Transmille 3010, 3041 Data sheet

DECLARATION OF CONFORMITY

Manufacturer's Name: Transmille Ltd. Manufacturer's Address: Unit 4, Select Business Centre

Lodge Road Staplehurst TN12 0QW. United Kingdom.

Declares, that the product

Product Name: Multi-product Calibrator

Model Number: 3050A / 3041A / 3010A

Product Options: This declaration covers all options of the above product(s)

Conforms with the following European Directives:

The product herewith complies with the requirements of the Low Voltage Directive 73/73EEC and the EMC Directive 89/336/EEC (including 93/68/EEC) and carries the CE Marking accordingly

Conforms with the following product standards:

EMC

IEC616326-1:1997+A1:1998 / EN 61326-1:1997+A1:1998 EN55011:1991

Standard Limit

IEC 61000-4-2:1995+A1:1998 / EN 61000-4-2:1995 Group 1Class A IEC 61000-4-3:1995 / EN 61000-4-3:1995 4kV CD, 8kV AD IEC 61000-4-4:1995 / EN 61000-4-4:1995 3 V/m, 80-1000 MHz IEC 61000-4-5:1995 / EN 61000-4-5:1995 0.5kV signal lines, 1kV power lines IEC 61000-4-6:1996 / EN 61000-4-6:1996 0.5kV line-line, 1kV line-ground IEC 61000-4-11:1994 / EN 61000-4-11:1994 3V, 0.15-80 MHz I cycle, 100%

Dips: 30% 10ms; 60% 100ms Interrupt > 95%@5000ms

SAFETY

IEC 61010-1:1990+A1:1992+A2:1995 / EN 61010-1:1993+A2:1995

16/01/2011

Date Of Issue Managing Director

Revision No: 1.00 : 16/01/2011

3010A EXTENDED SPECIFICATIONS General Specifications TRANSMILLE LTD

Warm Up Time

Standard Interfaces

Double the time since last used up to 20 minutes maximum

RS232 Optional Interfaces GPIB (IEEE-488) : USB (Universal Serial Bus) Temperature Performance Storage : -5°C to +60°C

Operation : 0°C to +50°C Relative Humidity Operation : <80% to 30°C, <70% to 40°C, <40% to 50°C

Storage : <95%, non-condensing Altitude Operation : 3000m (10,000ft) Maximum

Transit : 12000m (40,000ft) Maximum EMC & Safety The calibrator line input plug must be earthed

See D.O.C for full details Line Power Line Voltage Selectable : 110V / 230V

Line Frequency : 50Hz to 60Hz

Line Voltage Variation : -6% +10% Power Consumption 28 Watts (Standby) 200 Watts (Maximum) Low Analogue Isolation 100V Connections

Voltage / 2 Wire Resistance 1x Black : 1x White 4mm Safety sockets

Low Current (<=2A)

High current (>2A)

Earth Connection

1x Black : 1x Red 4mm Safety sockets 1x Blue : 1x Yellow 4mm Safety sockets 1x Green 4mm Safety Socket

Oscilloscope Functions 2x BNC terminal

Feature (Ext. Pod) 1x Female 'D' type socket

RS232 Interface 1x Female 'D' type socket RS232 Settings Baud Rate 9600

Parit

None Data Bits 8 Stop Bits 1

Display Information Type Backlit blue on white STN Type

Viewing Area 133mm * 39mm Resolution 240 x 64 dots Backlight Type LED

Brightness

230 to 260 cd/m

Indicators Voltage / Current / High Current Red LED (between terminals)

Negative to ground Green LED (left of Earth terminal) Oscilloscope Green LED (right of BNC Connector) Feature Connector (Ext. Pod) Green LED (right of 'D' type connector)

Keyboard Rubber key Fuses Mains Inlet 3.15A A/S (240 Volt)

5A A/S (110 Volt operation)

Isolation Outputs are opto-isolated from mains earth and the RS-232 interface

Maximum common mode voltage between earth and the low terminals 30 Volts ac/dc.

Dimensions & Weights

Calibrator Only 14cm x 43cm x 46cm : 12.5kgs Calibrator in Shipping Box 58cm x 56cm x 37cm : 15kgs Calibrator in Soft Carry Case 49cm x 50cm x 19cm : 13.5kgs Calibrator in Hard Transit case 55cm x 56cm x 26cm : 22kgs

Warranty Period 3 Years (Parts & Labour)

Recommended Service Interval

Supplied Connections

1 Year

1x Serial Interface Connection

1x Mains Lead 1x Adaptor Connection Lead (if at least one adaptor ordered)

Optional Lead Set Kit 1x Voltage connection leadset

1x Low Current connection leadset 1x High current connection leadset 1x AC connection leadset

Mounting Kit (optional) 3U rack mount kit Case Colou

Cream (RAL 9002)

Due to continuous development specifications may be subject to change. 3010A Extended Specifications General Specifications : V1.50

Page 1

3010A EXTENDED SPECIFICATIONS DCV Specifications TRANSMILLE LTD

Note 1: All

Note 2: Limited by 50 Oh

Note 3

1 year Total Accuracy Specifications at Tcal ±5°C & Range Parameters

Range

0-202mV 0.01uV

0.2-2.02V 0.1uV 50mA 150V 9 + 2.5 2-20.2V 1uV 50mA 150V 8 + 24

20-202V 10uV

200-1025V 100uV

Resolution Max. Burden 1 Year Total

Current ppm set uV

1mA

Typical Output

Resistance

50 Ohms

Overload

Protection

20 V 15 + 2

0.2 Ohms

20mA 20mA

0.7 Ohms

0.5 Ohms

1200V 12 + 240 1200V 12 + 2400

Stability (Accuracy relative to calibration Standards)

Range

24 Hour Stability

ppm Set uV uV ppm Set uV ppm Set uV ppm Set uV ppm Set uV

0-202mV 2 + 1 0.3 9.6 + 2 10.8 + 2 12 + 2 16.8 + 2.8

0.2-2.02V 2 + 1.2 0.4 5.6 + 2.5 6.3 + 2.5 7 + 2.5 9.8 + 3.5 2-20.2V 2 + 9 3 4.8 + 24 5.4 + 24 6 + 24 8.4 + 33.6

20-202V 3.5 + 120 40 8 + 240 9 + 240 10 + 240 14 + 336

200-1020V 5 + 1100 363 8 + 2400 9 + 2400 10 + 2400 14 + 3360

Noise

90 day Rel 180 Day Rel 1 year Rel 2 year Rel

Notes

For safety the trip is controlled by a fail-safe circuit independant of the processor which shuts the high voltage output off in the event of an overload. Note 4: Typical RMS noise figures at 50% of full scale, bandwidth 1Hz to 10Hz.

High Voltage Safety

High voltage output is ramped to allow instrument under test to auto range. Standby is automatically activated when setting voltages greater than 20V or 200V from a lower voltage.

Standby is automatically selected for high voltage (>20V) after 20 minutes on the same setting. High voltage (> 20V) output is indicated to user through an audible warning beep. An external high voltage output/standby control switch is available as an option.

2 Wire output / Remote sensing not available. Isolation : Floating or grounded selection available as standard. Maximum floating voltage : 100V Specifications apply at TCal ± 5°C Outside this range an allowance of 0.18 x 1 Year Spec. per °C should be added.

owance must be made for output resistance when driving into a load.

m output impedance.

: Internally adjustable from 2mA to 30mA - Factory set to 20mA as standard.

Due to continuous development specifications may be subject to change. 3010A Extended Specifications DCV Specifications : V1.50

Page 2

3010A EXTENDED SPECIFICATIONS DCI Specifications TRANSMILLE LTD

1 year Total Accuracy Specifications at TCal ±5°C & Range Parameters

Range

Resolution Compliance Overload 1 Year Total

0-202uA 10pA 10mH 150V 0.01 + 0.01

0.2-2.02mA 100pA 10mH 150V 0.005 + 0.03 2-20.2mA 1nA 10mH 150V 0.005 + 0.2

20-202mA 10nA 10mH 150V 0.005 + 2

0.2-2.02A 100nA 10mH 150V 0.013 + 30 2-20.2A 1uA 10mH 150V 0.03 + 300

20.2-30A 10uA 10mH 150V 0.05 + 450

Max. Inductive

Load

oltage Protection % set u

4.2 Volts

3.9 Volts

Stability (Accuracy relative to calibration Standards)

Range

0-202uA 0.006 + 0.01 0.007 + 0.01 0.008 + 0.01 0.011 + 0.014

0.2-2.02mA 0.0032 + 0.03 0.0036 + 0.03 0.004 + 0.03 0.006 + 0.042 2-20.2mA 0.0032 + 0.2 0.0036 + 0.2 0.004 + 0.2 0.006 + 0.28

20-202mA 0.0032 + 2 0.0036 + 2 0.004 + 2 0.006 + 2.8

0.2-2.02A 0.0056 + 30 0.006 + 30 0.007 + 30 0.01 + 42 2-20.2A

20.2-30A

Noise

90 Day Rel 180 Day Rel 1 Year Rel 2 Year Rel

0.1-1Hz %Set u

180pA 500pA

4nA

40nA

1uA 20uA 20uA

0.016 + 300 0.018 + 300 0.02 + 300 0.028 + 420

0.024 + 450 0.027 + 450 0.03 + 450 0.042 + 630

%Set u

Notes

Note 1 : Typical RMS noise figures at 50% of full scale. Note 2 : Power & temperature sensor on 30A range - microprocessor monitors & protects from overheating.

Higher resistance loads allow a longer ON period. See graphs 1 and 2 for details. Note 3 : Specifications apply to loads of less than 10% of the maximum burden voltage. Note 4: Zero or floor allowance.

Specifications apply at TCal ± 5°C Outside this range an allowance of 0.18 x 1 Year Spec. per °C should be added.

Due to continuous development specifications may be subject to change. 3010A Extended Specifications DCI Specifications : V1.50

Page 3

3010A EXTENDED SPECIFICATIONS DCI Specifications TRANSMILLE LTD

Graph 1* : Operating time on 30A range with current into a short circuit at 20°C Continuous current in availiable up to 10A output.

* Note Timing is started after a minimum period of 7 minutes at zero output.

Shorter periods will reduce the output time availiable.

Due to continuous development specifications may be subject to change. 3010A Extended Specifications DCI Specifications : V1.50

Page 4

3010A EXTENDED SPECIFICATIONS ACV Specifications TRANSMILLE LTD

1 year Total Accuracy Specifications at TCal ±5°C & Range Parameter

Range Frequency

0-202mV 10 to 44Hz 1uV

45 to 999Hz 1uV

1 to 19.999kHz 1uV

20 to 99.999kHz 1uV

100 to 500kHz 1uV

0.2-2.02V

2-20.2V 10 to 44Hz 100uV 50mA 0.2 Ohms 1200V 0.0500 + 1600

20-202V 30Hz to 44Hz 1mV

200-1020V

10 to 44Hz 10uV 50mA 0.2 Ohms 1200V 0.0500 + 180

45 to 999Hz 10uV 50mA 0.2 Ohms 1200V 0.0160 + 120

1 to 19.999kHz 10uV 50mA 0.2 Ohms 1200V 0.0210 + 180

20 to 99.999kHz 10uV 50mA 0.2 Ohms 1200V 0.0650 + 300

100 to 500kHz* 10uV 50mA 0.2 Ohms 1200V 0.3000 + 450

45 to 999Hz 100uV 50mA 0.2 Ohms 1200V 0.0160 + 1000

1 to 19.999kHz 100uV 50mA 0.2 Ohms 1200V 0.0210 + 1600

20 to 100kHz 100uV 50mA 0.2 Ohms 1200V 0.0600 + 3000

45Hz to 99.999kHz 1mV

1 to 9.999kHz 1mV

10 to 40KHz 1mV

30 to 44Hz 10mV

45 to 999Hz 10mV

1kHz to 10kHz 10mV

Resolution

Max. Burden

Current

1mA 1mA 1mA 1mA

1mA

20mA 15mA 15mA

20mA 15mA

Typical Output

Resistance % set uV

50 Ohms 20 V 0.0800 + 15 50 Ohms 20 V 0.0160 + 15 50 Ohms 20 V 0.0200 + 28 50 Ohms 20 V 0.1000 + 40 50 Ohms 20 V 0.4000 + 100

0.5 Ohms 1200V 0.0500 + 20mV

0.5 Ohms 1200V 0.0150 + 12mV

0.5 Ohms 1200V 0.0200 + 16mV

0.5 Ohms 1200V 0.0300 + 30mV

0.7 Ohms 1200V 0.0550 + 200mV

0.7 Ohms 1200V 0.0200 + 60mV

0.7 Ohms 1200V 0.0250 + 120mV

Protection

1 Year AccuracyOverload

Stability (Accuracy relative to calibration Standards)

Range Frequency Frequency 90 day Rel 180 Day Rel 1 year Rel 2 year Rel

Resolution

0-202mV 10 to 44Hz 0.0480 + 12 0.0540 + 13.5 0.0600 + 15 0.0840 + 21

45 to 999Hz 0.0080 + 12 0.0090 + 15 0.0100 + 15 0.0140 + 21

1 to 19.999kHz 0.0096 + 22.4 0.0108 + 28 0.0120 + 28 0.0168 + 39

20 to 99.999kHz 0.0720 + 32 0.0810 + 40 0.0900 + 40 0.1260 + 56

100 to 500kHz 0.2400 + 80 0.2700 + 100 0.3000 + 100 0.4200 + 140

0.2-2.02V

10 to 44Hz 0.0360 + 144 0.0405 + 180 0.0450 + 180 0.0630 + 252

45 to 999Hz 0.0112 + 96 0.0126 + 120 0.0140 + 120 0.0196 + 168

1 to 19.999kHz 0.0128 + 144 0.0144 + 180 0.0160 + 180 0.0224 + 252

20 to 99.999kHz 0.0464 + 240 0.0522 + 300 0.0580 + 300 0.0812 + 420

100 to 500kHz 0.2000 + 360 0.2250 + 450 0.2500 + 450 0.3500 + 630

2-20.2V 10 to 44Hz 0.0344 + 1280 0.0387 + 1600 0.0430 + 1600 0.0602 + 2240

45 to 999Hz 0.0104 + 800 0.0117 + 1000 0.0130 + 1000 0.0182 + 1400

1 to 19.999kHz 0.0128 + 1280 0.0144 + 1600 0.0160 + 1600 0.0224 + 2240

20 to 100kHz 0.0416 + 2400 0.0468 + 3000 0.0520 + 3000 0.0728 + 4200

20-202V 30Hz to 44Hz 0.0344 + 20mV 0.0387 + 20mV 0.0430 + 20mV 0.0602 + 28mV

45Hz to 999Hz 0.0104 + 12mV 0.0117 + 12mV 0.0130 + 12mV 0.0182 + 16mV

1 to 9.999kHz 0.0128 + 16mV 0.0144 + 16mV 0.0160 + 16mV 0.0224 + 22mV

10 to 40Khz 0.0192 + 30mV 0.0216 + 30mV 0.0240 + 30mV 0.0336 + 56mV

200-1020V

30 to 44Hz 0.0400 + 200mV 0.0450 + 200mV 0.0500 + 200mV 0.0700 + 280mV

45 to 999Hz 0.0120 + 60mV 0.0135 + 60mV 0.0150 + 60mV 0.0210 + 105mV

1kHz to 10kHz 0.0160 + 120mV 0.0180 + 120mV 0.0200 + 120mV 0.0280 + 180mV

All specifications apply from 10% of full scale.

1Hz 1Hz 1Hz 1Hz 1Hz

1Hz 1Hz 1Hz 1Hz 1Hz 1Hz 1Hz 1Hz 1Hz 1Hz 1Hz 1Hz 1Hz

1Hz 1Hz 1Hz

AC Frequency Accuracy : 30ppm

Notes

Note 1: Current limited by 50 ohms output resistance. Note 2 : Internally adjustable from 2mA to 30mA - Factory set to 20mA as standard

Note 3 : Frequency and voltage combinations are limited. Note 4 : Specifications apply up to 10% of maximum load current. Above this level, allowance must be made for output resistance. Note 5 : Zero or floor allowance. Note 6 : 1V to 1 MHz, 2V to 500kHz

For safety the trip is controlled by a fail-safe circuit independant of the processor which shuts the high voltage output off in the event of an overload.

%Set uV %Set uV %Set uV %Set uV

Due to continuous development specifications may be subject to change. 3010A Extended Specifications ACV Specifications : V1.50

Page 5

+ 15 hidden pages