Transition Networks J/E-PSW-FX-02(SC), J/E-PSW-FX-02(SM), SPS-1872-CC, SPS-1872-SA, E-MCR-04 User Manual
...
User’s Guide
J/E-PSW-FX-02
Stand-Alone Media Converter
• Just Convert-IT
• 10/100 Bridging (2-Port)
• 10Base-T/100Base-TX to 100Base-FX
The J/E-PSW-FX-02 Ethernet/Fast Ethernet 2-port bridging media converter
connects 10Base-T Ethernet or 100Base-TX Fast Ethernet twisted-pair copper
network devices to network devices on a 100Base-FX Fast Ethernet fiber network.
Part Number Port One - Copper
10Base-T/100Base-TX
Port Two - Duplex Fiber-Optic
100Base-FX
J/E-PSW-FX-02 RJ-45
100 m (328 ft)*
ST, 1300 nm multimode
2 km (1.2 miles)
J/E-PSW-FX-02(SC) RJ-45
100 m (328 ft)*
SC, 1300 nm multimode
2 km (1.2 miles)
J/E-PSW-FX-02(SM) RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
20 km (12.4 miles)
J/E-PSW-FX-02-100 RJ-45
100 m (328 ft)*
SC, 1310 nm TX/1550 nm RX
SM, 20 km(12.4 miles)**
J/E-PSW-FX-02-101 RJ-45
100 m (328 ft)*
SC, 1550 nm TX/1310 nm RX
SM, 20 km (12.4 miles)**
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .5
Cable Specifications . . . . . . . . . . .8
Technical Specifications . . . . . . . .9
Troubleshooting . . . . . . . . . . . . .10
Contact Us . . . . . . . . . . . . . . . . .11
Compliance Information . . . . . . .12
* Typical maximum cable distance. Actual
distance is dependent upon the physical
characteristics of the network.
**Single Fiber, install in pairs.
Part Number Description
SPS-1872-SA Optional External Power Supply; 18-72VDC Stand-Alone;
Output: 12.6VDC, 1.0 A
SPS-1872-CC Optional External Power Supply; 18-72VDC Piggy-back;
Output: 12.6VDC, 1.0 A
E-MCR-04 12-Slot Media Converter Rack (includes universal internal power
supply) 17 x 15 x 5 in. (432 x 381 x 127 mm)
WMBS Optional Wall Mount Brackets
Length: 3.2 in. (81 mm), Fits converter length: 3.9 in. (99 mm)
WMBV Optional Vertical Mount Bracket; Length: 5.0 in. (127 mm)
WMBD Optional DIN Rail Mount Bracket; Length: 5.0 in. (127 mm)
WMBD-FS Optional DIN Rail Mount Bracket (flat, small); Length: 3.1in. (79 mm)
Optional Accessories (sold separately)
2
J/E-PSW-FX-02
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
Installation
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting the 4-position switch. Failure to observe this caution
could result in damage to the media converter.
Setting the 4-position switch
The 4-position switch is located on the
rear panel of the media converter. Use
a small, flat-blade screwdriver to set
the recessed switches. (See the
drawing to the right.)
1. Auto-Negotiation
UP Enables Auto-Negotiation on the copper port.
Advertises 100 Mb/s full-duplex and half duplex,
and 10 Mb/s full-duplex and half duplex.
DOWN Disables Auto-Negotiation on the copper port.
2. Copper Mode
(Applies only if switch 1 is DOWN.)
UP Forces full-duplex operation on the copper port.
DOWN Forces half-duplex operation on the copper port.
3. Speed
(Applies only if switch 1 is DOWN.)
UP Forces 100 Mb/s operation on the copper port.
DOWN Forces 10 Mb/s operation on the copper port.
4. Fiber Mode
UP Forces full-duplex operation on the fiber port.
DOWN Forces half-duplex operation on the fiber port.
Speed (up=100Mb/s)
Copper Mode (up=Full-Duplex)
Auto-Negotiation (up=Enabled)
Fiber Mode
(up=Full-Duplex)
1234
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
3
Installation -- Continued
Installing the fiber cable
1. Locate IEEE 803.2™ compliant 100Base-FX fiber cable with male, twostranded TX to RX connectors installed at both ends.
2. Connect the fiber cables to the J/E-PSW-FX-02 media converter as
described:
• Connect the male TX cable connector the female TX port.
• Connect the male RX cable connector to the female RX port.
3. Connect the fiber cables to the other device (another media converter,
hub, etc.) as described:
• Connect the male TX cable connector the female RX port.
• Connect the male RX cable connector to the female TX port.
Connect the fiber cable
to the media converter
as shown.
Connect the fiber cable
to the other device
(media converter,
hub, etc.) as shown
RX
TX
RX
TX
Installing the twisted-pair copper cable
1. Locate or build IEEE 803.2™ compliant 10Base-T or 100Base-TX cables,
with male RJ-45 connectors installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on
the media converter.
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45
port on the other device (switch, workstation, etc.).
NOTE: The MDI (straight-through) or MDI-X (crossover) cable connection is
configured automatically, according to the network conditions.
RJ-45 port
on the other device
(switch, work station, etc.)
RJ-45 port
on the media
converter
4
J/E-PSW-FX-02
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
Installation -- Continued
Powering the media converter
NOTE: The external power supply provided with this product is UL listed by
the power supply’s manufacturer.
AC
1. Connect the barrel connector on the power adapter to the media
converter’s power port (located on the back of the media converter).
2. Connect the power adapter plug to AC power.
3. Verify that the media converter is powered ON by observing the
illuminated power indicator LED.
DC
Consult the user’s guide for the Transition Networks SPS-1872-xx DC external
power supply for powering the media converter.
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
5
Operation
Using the status LEDs
Use the status LEDs to monitor the media converter and the network connections.
Link Act (Fiber Link/Activity)
On = fiber link connection.
Flashing = fiber network activity.
FD (Fiber Duplex)
On = full-duplex.
Off = half-duplex.
PWR (Power)
On = connection to external AC or DC power.
100 (Copper Speed)
On = 100 Mb/s.
Off = 10 Mb/s.
Link Act (Copper Link/Act)
On = copper link connection.
Flashing = copper network activity.
FD (Copper Duplex)
On = full-duplex.
Off = half-duplex.
Lnk
Act
10/100Base-TX
RX
TX
100Base-FX
Lnk
ActPwr
FD 100 FD
Loading...