Transition Networks CBFTF1011-140, CBFTF1013-140, CBFTF1014-140, CBFTF1015-140, CBFTF1016-140 User Manual
...
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .8
Cable Specifications . . . . . . . . . .12
Technical Specifications . . . . . . .13
Troubleshooting . . . . . . . . . . . . .14
Compliance Information . . . . . . .15
Contact Us . . . . . . . . . . . . . . . . .16
Part Number Copper - four (4) ports
10Base-T/100Base-TX
Duplex Fiber-Optic - two (2) ports
100Base-FX
CBFTF1011-140 RJ-45
100 m (328 ft)*
ST, 1300 nm multimode
2 km (1.2 miles)*
CBFTF1013-140 RJ-45
100 m (328 ft)*
SC, 1300 nm multimode
2 km (1.2 miles)*
CBFTF1014-140 RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
20 km (12.4 miles)*
CBFTF1015-140
(long haul)
RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
40 km (24.8 miles)*
CBFTF1016-140
(extra long haul)
RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
60 km (37.2 miles)*
CBFTF1017-140
(long wave length)
RJ-45
100 m (328 ft)*
SC, 1550 nm single mode
80 km (49.7 miles)*
CBFTF1018-140 RJ-45
100 m (328 ft)*
MT-RJ, 1300 nm multimode
2 km (1.2 miles)*
CBFTF1025-140 RJ-45
100 m (328 ft)*
MT-RJ, 1310 nm single mode
5 km (3.1 miles)*
User’s Guide
CBFTF10xx-14x
Slide-in-Module Media Converter
• Copper to Fiber
• 10/100 Bridging 6-Port
• (4 copper / 2 fiber)
• 10/100Base-TX to 100Base-FX
The CBFTF10xx-14x 6-port Ethernet/Fast Ethernet bridging media converter is
designed to be installed into a Transition Networks PointSystem™ chassis and
allows connection of 10Base-T Ethernet and/or 100Base-TX Fast Ethernet twistedpair copper network devices to network devices on a 100Base-FX Fast Ethernet
fiber network.
* Typical maximum cable distance. Actual distance is dependent upon the
physical characteristics of the network.
2
CBFTF10xx-14x
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
* Typical maximum cable distance. Actual distance is dependent upon the
physical characteristics of the network. (TX) = transmit (RX) = receive
** CBFTF1029-140 and CBFTF1029-141 are intended to be installed in the same
network where one is the local converter and the other is the remote.
*** CBFTF1029-142 and CBFTF1029-143 are intended to be installed in the same
network where one is the local converter and the other is the remote.
The stand alone version of this media converter is SBFTF10xx-14x. For more
information, see the SBFTF10xx-14x user’s guide on-line at: www.transition.com.
Installation
Copper and Fiber Ports
The figure below illustrates the locations of the four (4) twisted-pair copper ports
and the two (2) fiber ports.
Part Number Copper - four (4) ports
10Base-T/100Base-TX
Fiber-Optic - two (2) ports
Single Fiber
CBFTF1029-140 RJ-45
100 m (328 ft)*
SC, 1310 mn (TX)/1550 nm (RX)
single mode, 20 km (12.4 miles
CBFTF1029-141 RJ-45
100 m (328 ft)*
SC, 1550 mn (TX)/1310 nm (RX)
single mode, 20 km (12.4 miles)*
CBFTF1029-142 RJ-45
100 m (328 ft)*
SC, 1310 mn (TX)/1550 nm (RX)
single mode, 40 km (24.8 miles)*
CBFTF1029-143 RJ-45
100 m (328 ft)*
SC, 1550 mn (TX)/1310 nm (RX)
single mode, 40 km (24.8 miles)*
10/100TX
FD
LACT
PWR
10/100TX
Twisted-Pair
Port 1 (TP1)
Twisted-Pair
Port 2 (TP2)
10/100TX
FD
LACT
10/100TX
Twisted-Pair
Port 3 (TP3)
Twisted-Pair
Port 4 (TP4)
Fiber Port 2
(F2)
Fiber Port 1
(F1)
100Base-FX
100Base-FX
CBFTF140
Installation -- Continued
Set the Dip Switches
The dip switches are located on the side of the media converter. Use a small,
flat blade screwdriver or a similar device to set each dip switch.
“SW1” switches 1 - 6
Dip switches 1, 2, and 3 apply only to twisted-pair copper port 1 (TP1).
Dip switch 4 applies to fiber port 1 (F1).
Dip switch 5 applies to all twisted-pair copper ports (TP1, TP2, TP3, TP4).
Dip switch 6 applies to both fiber ports (F1, F2).
“Config. Switches” 1 - 4
Dip switches 1, 2, 3, and 4 apply only to twisted-pair copper port 2 (TP2).
NOTE: Switches 1, 2, and 3 apply only to twisted-pair copper port 1 (TP1).
3
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
1. Twisted-Pair Auto-Negotiation
UP (Enabled) - The media converter “advertises”
ALL rate and mode capabilities to the network:
• 100Mb/s full-duplex • 100Mb/s half-duplex,
• 10Mb/s full-duplex • 10Mb/s half-duplex.
DOWN (Disabled) - The bridging media converter
does not “advertise” the rate and mode
capabilities to the network. Switches 2 and 3 are
then used to set the twisted-pair rate and mode.
2. Twisted-Pair Rate
UP (100Base-TX) - Sets the twisted-pair rate to
100Base-TX.
DOWN (10Base-T) - Sets the twisted-pair rate to
10Base-T.
3. Twisted-Pair Mode
UP (Full-Duplex) - The twisted-pair cable
distances are constrained by the cable
requirements (see pages 1 and 2).
DOWN (Half-Duplex): - The twisted-pair cable
distances are constrained by the 512-Bit Rule (see
page 9).
DOWN
1
UP
Twisted-Pair Auto-Negotiation ON
Twisted-Pair Auto-Negotiation OFF
Twisted-pair 100Base-TX
Twisted-pair 10Base-T
DOWN
UP
2
Twisted-pair Full-Duplex
Twisted-pair Half-Duplex
DOWN
UP
3
4
CBFTF10xx-14x
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Installation -- Continued
Set the Dip Switches -- Continued
NOTE: Dip switch 4 (in the “SW” set) applies to fiber port 1 (F1).
4. Fiber Mode (Fiber Port 1)
UP (Full-Duplex) - The cable distances for fiber port
1 (F1) are constrained by the cable requirements (see
pages 1 and 2).
DOWN (Half-Duplex) - The cable distances for fiber
port 1 (F1) are constrained by the 512-Bit Rule (see
pages 9).
NOTE: Dip switch 5 (in the “SW” set) applies to all twisted-pair copper ports
(TP1, TP2, TP3, TP4).
5. AutoCross
UP (Enable) - The media converter connects
automatically to either straight-through or crossover
twisted-pair copper cable.
DOWN (Disable) - Either straight-through or
crossover twisted-pair copper cable must be
installed, according to the site requirements
NOTE: Dip switch 6 (in the “SW” set) applies to both fiber ports (F1, F2).
6. Fiber Redundancy
UP (Disable) - When Fiber Redundancy is disabled,
Fiber Port 1 (F1) and Fiber Port 2 (F2) act as normal
bridging ports.
DOWN (Enable) - When Fiber Redundancy is
enabled, Fiber Port 1 (F1) and Fiber Port 2 (F2) are
configured as either forwarding or disabled. At any
given time, one port will be disabled and one port
will be forwarding.
Redundant Fiber Disable
Redundant Fiber Enable
6
UP
DOWN
Fiber Full-Duplex
Fiber Half-Duplex
DOWN
UP
4
AutoCross Enable
AutoCross Disable
UP
5
DOWN
5
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
Installation -- Continued
Set the Dip Switches -- Continued
NOTE: Dip switches 1, 2, 3, and 4 (in the Config. Switches set) apply only to
twisted-pair copper port 2 (TP2).
1. Twisted-Pair Auto-Negotiation
UP (Enabled) - The media converter “advertises”
ALL rate and mode capabilities to the network:
• 100Mb/s full-duplex • 100Mb/s half-duplex,
• 10Mb/s full-duplex • 10Mb/s half-duplex.
DOWN (Disabled) - The bridging media converter
does not “advertise” the rate and mode
capabilities to the network. Switch 2 and switch 3
are then used to set the twisted-pair rate and mode.
2. Twisted-Pair Rate
UP (100Base-TX) - Sets the twisted-pair rate to
100Base-TX.
DOWN (10Base-T) - Sets the twisted-pair rate to
10Base-T.
3. Twisted-Pair Mode
UP (Full-Duplex) - The twisted-pair cable
distances are constrained by the cable
requirements (see pages 1 and 2).
DOWN (Half-Duplex) - The twisted-pair cable
distances are constrained by the 512-Bit Rule (see
page 9).
4. Monitor for Twisted-Pair Port 2 (TP2)
UP (Off) - The twisted-pair port 2 (TP2) functions
as directed by switches 1, 2, and 3.
DOWN (On) - The twisted-pair port 2 (TP2)
functions as a “sniffer” port and transmits all
packets received from ports F1 and TP1.
Twisted-Pair Full-Duplex
Twisted-Pair Half-Duplex
UP
DOWN
3
Monitor on TP2 OFF
Monitor on TP2 ON
UP
DOWN
4
Twisted-Pair 100Base-TX
Twisted-Pair 10Base-T
UP
DOWN
2
UP
DOWN
1
Twisted-Pair Auto-Negotiation ON
Twisted-Pair Auto-Negotiation OF
F
Loading...