Transition Networks CBFTF1011-120, CBFTF1013-120, CBFTF1014-120, CBFTF1015-120, CBFTF1016-120 User Manual
...
Part Number Copper - five (5) ports
10Base-T/100Base-TX
Duplex Fiber-Optic - one (1) port
100Base-FX
CBFTF1011-120 RJ-45
100 m (328 ft)*
ST, 1300 nm multimode
2 km (1.2 miles)*
CBFTF1013-120 RJ-45
100 m (328 ft)*
SC, 1300 nm multimode
2 km (1.2 miles)*
CBFTF1014-120 RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
20 km (12.4 miles)*
CBFTF1015-120
(long haul)
RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
40 km (24.8 miles)*
CBFTF1016-120
(extra long haul)
RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
60 km (37.2 miles)*
CBFTF1017-120
(long wave length)
RJ-45
100 m (328 ft)*
SC, 1550 nm single mode
80 km (49.7 miles)*
CBFTF1018-120 RJ-45
100 m (328 ft)*
MT-RJ, 1300 nm multimode
2 km (1.2 miles)*
CBFTF1025-120 RJ-45
100 m (328 ft)*
MT-RJ, 1310 nm single mode
5 km (3.1 miles)*
User’s Guide
CBFTF10xx-12x
Slide-in-Module Media Converter
• Copper to Fiber
• 10/100 Bridging 6-Port
• (5 copper / 1 fiber)
• 10/100Base-TX to 100Base-FX
The CBFTF10xx-12x 6-port Ethernet/fast Ethernet bridging media converter is
designed to be installed into a Transition Networks PointSystem™ chassis and
allows connection of 10Base-T Ethernet and/or 100Base-TX fast Ethernet twistedpair copper network devices to network devices on a 100Base-FX fast Ethernet
fiber network.
* Typical maximum cable distance.
Actual distance is dependent upon the
physical characteristics of the network.
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .8
Cable Specifications . . . . . . . . . .12
Technical Specifications . . . . . . .13
Troubleshooting . . . . . . . . . . . . .14
Compliance Information . . . . . . .15
Contact Us . . . . . . . . . . . . . . . . .16
2
CBFTF10xx-12x
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
* Typical maximum cable distance. Actual distance is dependent upon the
physical characteristics of the network. (TX) = transmit (RX) = receive
** CBFTF1029-
120 and CBFTF1029-121 are intended to be installed in the same
network where one is the local converter and the other is the remote.
*** CBFTF1029-
122 and CBFTF1029-123 are intended to be installed in the same
network where one is the local converter and the other is the remote.
The stand-alone version of the media converter is SBFTF10xx-12x. For more
information, see the SBFTF10xx-12x user’s guide on-line at: www.transition.com.
Installation
Copper and Fiber Ports
The figure below illustrates the locations of the five (5) twisted-pair copper ports
and the one (1) fiber port.
Part Number Copper - four (4) ports
10Base-T/100Base-TX
Fiber-Optic - two (2) ports
Single Fiber
CBFTF1029-120 RJ-45
100 m (328 ft)*
SC, 1310 nm (TX)/1550 nm (RX)
single mode, 20 km (12.4 miles
CBFTF1029-121 RJ-45
100 m (328 ft)*
SC, 1550 nm (TX)/1310 nm (RX)
single mode, 20 km (12.4 miles)*
CBFTF1029-122 RJ-45
100 m (328 ft)*
SC, 1310 nm (TX)/1550 nm (RX)
single mode, 40 km (24.8 miles)*
CBFTF1029-123 RJ-45
100 m (328 ft)*
SC, 1550 nm (TX)/1310 nm (RX)
single mode, 40 km (24.8 miles)*
FD
LACT
PWR
T
wiste
d
Port 1
(
Twisted-Pair
Port 4 (TP4)
Twisted-Pair
Port 5 (TP5)
Fiber Port 1
(F1)
100Base-FX
10/100TX
10/100TX
Twisted-Pair
Port 2 (TP2)
Twisted-Pair
Port 3 (TP3)
Installation -- Continued
Set the Dip Switches
The dip switches are located on the side of the media converter. Use a small,
flat-blade screwdriver or a similar device to set each dip switch.
“SW1” switches 1 - 6
Dip switches 1, 2, and 3 apply only to twisted-pair copper port 1 (TP1).
Dip switch 4 applies to fiber port 1 (F1).
Dip switch 5 applies to all twisted-pair copper ports (TP1, TP2, TP3, TP4, TP5).
Dip switch 6 is not in use.
“Config. Switches” 1 - 4
Dip switches 1, 2, 3, and 4 apply only to twisted-pair copper port 2 (TP2).
NOTE: Switches 1, 2, and 3 apply only to twisted-pair copper port 1 (TP1).
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
3
1. Twisted-Pair Auto-Negotiation
UP (Enabled) - The media converter “advertises”
ALL rate and mode capabilities to the network:
• 100Mb/s full-duplex • 100Mb/s half-duplex,
• 10Mb/s full-duplex • 10Mb/s half-duplex.
DOWN (Disabled) - The bridging media
converter does not “advertise” the rate and mode
capabilities to the network. Switches 2 and 3 are
then used to set the twisted-pair rate and mode.
2. Twisted-Pair Rate
UP (100Base-TX) - Sets the twisted-pair rate to
100Base-TX.
DOWN (10Base-T) - Sets the twisted-pair rate to
10Base-T.
3. Twisted-Pair Mode
UP (Full-Duplex) - The twisted-pair cable
distances are constrained by the cable
requirements (see pages 1 and 2).
DOWN (Half-Duplex): - The twisted-pair cable
distances are constrained by the 512-Bit Rule (see
page 9).
DOWN
1
UP
Twisted-Pair Auto-Negotiation ON
Twisted-Pair Auto-Negotiation OFF
Twisted-pair 100Base-TX
Twisted-pair 10Base-T
DOWN
UP
2
Twisted-pair Full-Duplex
Twisted-pair Half-Duplex
DOWN
UP
3
4
CBFTF10xx-12x
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Installation -- Continued
Set the Dip Switches -- Continued
NOTE: Dip switch 4 (in the “SW” set) applies to fiber port 1 (F1).
4. Fiber Mode (Fiber Port 1)
UP (Full-Duplex) - The cable distances for fiber port
1 (F1) are constrained by the cable requirements (see
pages 1 and 2).
DOWN (Half-Duplex) - The cable distances for fiber
port 1 (F1) are constrained by the 512-Bit Rule (see
page 9).
NOTE: Dip switch 5 (in the “SW” set) applies to all twisted-pair copper ports
(TP1, TP2, TP3, TP4, TP5).
5. AutoCross
UP (Enable) - The media converter connects
automatically to either straight-through or crossover
twisted-pair copper cable.
DOWN (Disable) - Either straight-through or
crossover twisted-pair copper cable must be
installed, according to the site requirements
6. Not in use
Fiber Full-Duplex
Fiber Half-Duplex
DOWN
UP
4
AutoCross Enable
AutoCross Disable
UP
5
DOWN
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
5
Installation -- Continued
Set the Dip Switches -- Continued
NOTE: Dip switches 1, 2, 3, and 4 (in the Config. Switches set) apply only to
twisted-pair copper port 2 (TP2).
1. Twisted-Pair Auto-Negotiation
UP (Enabled) - The media converter “advertises”
ALL rate and mode capabilities to the network:
• 100Mb/s full-duplex • 100Mb/s half-duplex,
• 10Mb/s full-duplex • 10Mb/s half-duplex.
DOWN (Disabled) - The bridging media converter
does not “advertise” the rate and mode
capabilities to the network. Switch 2 and switch
3 are then used to set the twisted-pair rate and
mode.
2. Twisted-Pair Rate
UP (100Base-TX) - Sets the twisted-pair rate to
100Base-TX.
DOWN (10Base-T) - Sets the twisted-pair rate to
10Base-T.
3. Twisted-Pair Mode
UP (Full-Duplex) - The twisted-pair cable
distances are constrained by the cable
requirements (see pages 1 and 2).
DOWN (Half-Duplex) - The twisted-pair cable
distances are constrained by the 512-Bit Rule (see
page 9).
4. Monitor for Twisted-Pair Port 2 (TP2)
UP (OFF) - The twisted-pair port 2 (TP2) functions
as directed by switches 1, 2, and 3.
DOWN (ON) - The twisted-pair port 2 (TP2)
functions as a “sniffer” port and transmits all
packets received from ports F1 and TP1.
Twisted-Pair Full-Duplex
Twisted-Pair Half-Duplex
UP
DOWN
3
Monitor on TP2 OFF
Monitor on TP2 ON
UP
DOWN
4
Twisted-Pair 100Base-TX
Twisted-Pair 10Base-T
UP
DOWN
2
UP
DOWN
1
Twisted-Pair Auto-Negotiation ON
Twisted-Pair Auto-Negotiation OF
F
Loading...