Trane GBPD, GPPD, GPND, GKPD, GKND Installation Manual

Discharge Air
Nozzle Kits

Installation GPND-IN-1

Library Service Literature
Product Section Air Terminal Devices & Heat Products
Product Gas Unit Heaters
Model GPND/GPPD
Literature Type Installation
Sequence 1
Date August 1997
File No. SV-TD-UH-GPND-IN-1-897
Supersedes New

Models
GAND

GAPD
GBND
GBPD
GCND
GCPD
GEND
GEPD
GHND
GHPD
GKND
GKPD
GPND
GPPD

Sizes 100 through 400

Since the Companyhas a policy ofcontinuous productimprovement, it reserves the right to changespecifications and
design without notice.

© American Standard Inc. 1997

General Information

Table of Contents

General Information ................... 2

Literature Change History ................ 2

Warnings and Cautions ................. 2

Description ........................ 2

Installation ........................ 3

30° Nozzle Kit ...................... 3

45° Nozzle Kit ...................... 4

60° Nozzle Kit ...................... 5

90° Nozzle Kit ...................... 6

5-Way Blow Down Nozzle Kit .............. 7

Y-Splitter Nozzle Kit ................... 7

Literature Change History

GPND-IN-1 (August 1997)

Original issue of the manual.

Warnings and Cautions

Warnings and Cautions appear at
appropriate sections throughout
this manual.

WARNINGS!
alert the installer, owner,
operator or service personnel
to potential hazards which if
not avoided could result in
death or serious personal injury.

Cautions:
alert personnel to conditions
which if not avoided may result
in minor or moderate injury.
Also alerts against unsafe prac­tices causing equipment
damage.

Shipping Instructions

Before installing the nozzle kit, be
sure to confirm that the proper kit
has been sipped.

If a thorough inspection of the kit
reveals damage or material
shortages, file a claim with the
carrier immediately. Specify the
extent and type of damage found,
and notify the appropriate Trane
sales office. Do not install a
damaged nozzle kit without the
Trane sales representative’s
approval!

Description

The nozzle kits are used to direct
discharge air on unit heaters with
a variety of angles available.

2 GPND-IN-1

WARNING!
Disconnect the power source
before installing this kit to
prevent death or serious
personal injury due to
electrical shock.

For Use On Propeller and
Blower Unit Heaters
Natural or Power Vent

Kit Contents (Unassembled)
(2) Side Panels—L.H. & R.H.
(1) Top Panel
(1) Bottom Cross Brace

Installation—30° Nozzle Kit

(1) Bag of #8 Drill Screws

The following steps for
assembling are recommended in
sequence:

1. Remove seven (7) horizontal
louvers and louver cone
springs from unit heater and
set aside. (Note louver and
spring positions).

2. Drill three (3) 1/8" diameter
holes in each unit heater “side
panel” to dimensions shown,
(see drawing).

3. Fasten L.H. (Item 1) and R.H.
(Item 2) side panels to unit
heater “side panels” with three
(3) drill screws each using
holes drilled in Step 2 above.

4. Attach “top panel” (Item 3) to
nozzle side panels (Items 1 &

2) with six (6) drill screws.

5. Fasten “top panel” (Item 3) to
heater’s “upper trim panel”
utilizing existing screws at
each end. Then, using
remaining holes as template,
drill through with 1/8" diameter
drill and fasten with drill
screws.

6. Attach and fasten “bottom
cross brace” (Item 4) with two
(2) drill screws.

7. Install six (6) of the seven (7)
louvers and louver cone
springs removed from the unit
heater in Step 1.

GPND-IN-1 3