Trane CFEB 04 C0M1, CFEB 06 C0M1, CFEB 08 C0M1, CFEB 10 C0M1, CFEB 12 C0M1 Owner's Manual
...
Owner Manual
AQUA NEW STYLUS
Chilled Water Fan Coil
Convertible Type
CFEB Series 50/60 Hz
50 Hz Models
Cooling Only
CFEB 04 C0M1
CFEB 06 C0M1
CFEB 08 C0M1
CFEB 10 C0M1
CFEB 12 C0M1
CFEB 14 C0M1
CFEB 16 C0M1
CFEB 20 C0M1
60 Hz Models
Cooling Only
CFEB 04 C0M2
CFEB 06 C0M2
CFEB 08 C0M2
CFEB 10 C0M2
CFEB 12 C0M2
CFEB 14 C0M2
CFEB 16 C0M2
CFEB 20 C0M2
June 2017
UNT-SVU002-EN
General Information
General Information
Congratulations on your choice of a
Trane chilled water fancoil system.
These systems have been carefully
designed and manufactured under
strict Trane Worldwide Quality
Standards to provide you with years
of comfortable, convenient cooling
or heating/cooling with a minimum of
service.
This Owner Manual is given as a
guide to start-up, operation and
periodic maintenance by the user of
CFEB chilled water fancoil system.
It does not contain the full service
procedures necessary for the
continued successful operation of
this equipment. The services of a
qualied service technician should be
employed, through the maintenance
contract with a reputable service
company.
Read it completely before doing
anything with your air conditioning
system.
About this Manual
Cautions appear at appropriate
places in this instruction manual.
Your personal safety and the proper
operation of this machine require
that you follow them carefully. The
Trane Company assumes no liability
for the inappropriate usage of the
unit.
About the Unit
These CFEB units are assembled,
pressure tested, dehydrated, charged
and run tested before shipment. The
information contained in this manual
applies to CFEB units are designed
to operate in cooling mode only and
in cooling or heating modes.
Trane CFEB series of chilled water
fancoil systems oer three styles of
installation: oor, low wall and under
ceiling with both LCD wireless remote
control or wired control.
Trane CFEB series provide exibility
and savings.
Note: For model CFEB14, CFEB16
and CFEB20, there are only two
styles of installation: under ceiling
and low wall.
Reception
On arrival, inspect the unit before
signing the delivery note. Specify any
damage of the unit on the delivery
note, and send a registered letter of
protest to the last carrier of the goods
within 72 hours of delivery.
Notify the dealer at the same time.
The unit should be totally inspected
within 7 days of delivery. If any
concealed damage is discovered,
send a registered letter of protest to
the carrier within 7 days of delivery
and notify the dealer.
Warning
Warnings are provided at appropriate
places in this manual to indicate to
installers, operators and service
personnel of potentially hazardous
situations which, if not avoided,
COULD result in death or serious
injury.
Caution
Cautions are provided at appropriate
places in this manual to indicate to
installers, operators, and service
personnel of potentially hazardous
situations which, if not avoided, MAY
result in minor or moderate injury or
malfunction of the unit.
Your personal safety and the proper
operation of this unit require that
you follow them carefully. The Trane
Company assumes no liability for
installations or servicing performed
by unqualied personnel.
Warranty
Warranty is based on the general
terms and conditions by country.
The warranty is void if the equipment
is modied or repaired without
the written approval of The Trane
Company, if the operating limits are
exceeded or if the control system
or the electrical wiring is modied.
Damage due to misusage, lack of
maintenance or failure to comply with
the manufacturer’s instructions, is not
covered by the warranty obligation.
If the user does not conform to the
rules described in Owner Manual, it
may entail cancellation of warranty
and liabilities by The Trane Company.
Important
These instructions do not cover
all variations in systems, nor do
they provide for every possible
contingency to be met. Should
further information be desired or
should particular problems arise
which are not covered suciently for
the purchaser’s purposes, the matter
should be referred to your authorized
Trane dealer.
UNT-SVU002-EN
2
Contents
General Information ........................................................................2
Control Operation ............................................................................ 4
Wireless Remote Control ................................................................5
Digital Wired Control .......................................................................9
System Operation .......................................................................... 12
Electronic Room Thermostat .......................................................13
Maintenance ................................................................................... 14
Troubleshooting ............................................................................15
3
UNT-SVU002-EN
Control Operation
Infrared Remote Control
Unit Display and One-touch
Control Switch
Display Panel
Four lamps on the unit show
operating status.
1. FAN Lamp
This lamp lights when the fan is
operating.
2. COOLING Lamp
This lamp lights when the unit is
in COOL or DRY mode of operation.
3. TIMER Lamp
This lamp lights when the system is
being controlled by the timer.
4. Compressor Lamp
This lamp lights when compressor is
operated.
One Touch Control Switch (A)
This button is used for adjusting
operation without remote control unit.
UNT-SVU002-EN
4
Wireless Remote Control
Infrared Remote Control
Name and function of buttons
1. Infrared Signal Transmitter
Transmits the signal to indoor unit.
2. POWER Button
Press this button to start unit
operation.
Press this button again to stop unit
operation.
3. Temperature Setting Button
TEMP : Press this button to
increase the set temperature.
TEMP : Press this button to
decrease the set temperature.
4. FAN SPEED Button
Press this button to select fan
speed.
5. MODE Button
Press this button to select system
operation mode. In cooling only
system, a mode is selected in
sequence as FAN, COOL, DRY,
and back to FAN.
6. LOUVER Button
Press this button to adjust blade
direction.
7. SWEEP Button
Press this button to activate
or inactivate sweep motor to
distribute air ow.
8. FRONT BLADE Button
Press this button to activate or
inactivate front blade function.
9. ON TIMER Button
Press this button to set the on
timer of the unit operation.
10. OFF TIMER Button
Press this button to set the o
timer of the unit operation.
11. CLOCK Button
Press this button to set the clock to
the present time or see the present
time after ON or OFF TIMER was set.
12. LIGHT Button
Press this button to turn on the
LCD light.
13. POWERCOOL Button
Press this button to accelerate
capacity up.
14. ECONO Button
Press this button to save energy.
15. SLEEP Button
Press this button to control
temperature while sleeping and
press this button again to cancel.
16. SEND Button
Press this button to conrm the
operation of the unit according
to the LCD display or press and
hold for 5 seconds to toggle
temperature unit between Celsius
and Fahrenheit.
Installation of Batteries
1. Slide the back cover of the remote
control down to take it o.
2. Insert two dry batteries into the
slot. Be sure that the + and –
directions are correct.
3. Fix the back cover to the remote
control as before.
Attentions
• Batteries can be used
approximately for one year under
normal conditions.
• Always replace an identical type of
two batteries at the same time.
• Do not use manganese dry
batteries since they may cause a
malfunction.
• Do not use rechargeable (Ni-Cd)
batteries, because such batteries
may dier from standard dry cell
batteries in shapes, dimensions, or
performance.
• Take out all batteries if you are not
going to use the air-conditioner for
a long period of time.
5
UNT-SVU002-EN
Wireless Remote Control
Indicators on Infrared Remote
Control
1. CLOCK
Displays present
2. ON
TIMER
Display ON TIMER when ON
TIMER is
3. OFF
set.
TIMER
Display OFF TIMER when OFF
TIMER is
4.
Transmission
set.
The transmission indicator lights
when remote control transmits
signal to
5. SLEEP
the
Mode
Display sleep symbol after
activating
6. Set T
SLEEP
emperatur
Displays the set temperature (15ºC
30ºC) when FAN or POWERCOOL
mode is selected. The set
temperature will be disappeared
until FAN
or
is cancelled
7. FAN Speed
Display the selected fan speed
level: auto, low, medium, or high.
8. Operation
Displays the current operation
mode:
FAN, COOL, or DRY in
cooling only
9. SWEEP Function
Displays “SW” when sweep motor
is
activated.
10. ECONO
Displays
ECONO mode is
11. POWERCOOL
Displays “POWERCOOL” when
PO
WERCOOL
UNT-SVU002-EN
time.
Indicator
indoor
unit.
mode.
e
POWERCOOL mode
or complete.
Mode
system.
Mode
“ECONO”
activated.
Mode
mode is
activated.
to
when
Operation
Mode
FAN Mode
- Press Mode button to select
the
operation
- “FAN”
display
will be shown on the
mode.
when FAN mode is
selected.
- Press FAN
select
and the
Auto, Low, Medium, and High r
SPEED
the
desired fan speed level
display
button to
will
show
.
espectively
Note:
• In FAN mode, the LCD display
will not show set temperature and
cannot adjust set temperature,
SLEEP, ECONO, and
POWERCOOL mode.
COOL
Mode
- Press Mode button to select the
operation mode.
- “COOL” will be shown on the
display when COOL mode is
selected.
- Press either or button to set
the desired temperature between
15ºC to 30ºC.
- Press FAN SPEED button to
select the desired fan speed level
and the display will show.
Auto, Low, Medium, and High r
DRY
Mode
espectively
- Press Mode button to select the
operation mode.
- “DRY” will be shown on the display
when DRY mode is selected.
- Press either or button to set
the desired temperature between
15ºC to 30ºC.
- Press FAN SPEED button to
select the desired fan speed level
and the display will show.
Auto, Low, Medium, and High r
espectively
Note:
• In DRY mode, if the compressor
stops working, fan motor and
SWEEP function will be stopped;
fan motor and SWEEP function will
operate when compressor operates.
• SWEEP function will be cancelled
whenever LOUVER function is
selected.
• ECONO mode cannot be activated
during DRY mode operation.
CLOCK Setting
- Press CLOCK button to set
clock
and
the display
will be shown on
with
blinking hour
number.
- Press either or button to set
the clock to the present hour.
- Press CLOCK button again to
conrm hour setting and minute
number will be blinking.
- Press either or button to set
the clock to the present minute.
- Press CLOCK button again to
conrm minute setting; hour and
minute number will stop blinking
and the set time will be shown on
the display.
Note:
• If there are no other buttons
pressed within 15 seconds, clock
setting will be cancelled.
• User can conrm CLOCK setting
during CLOCK setting process by
pressing SEND button.
6
Wireless Remote Control
Timer Operation
Once you select the timer operation, the
settings are saved in the remote control.
Thereafter, the air-conditioner will start
operating under the same conditions
when you simply push the POWER
button on the remote control.
ON TIMER Setting
You can set ON TIMER to start the unit
automatically at any desired time up to
24 hours as real time.
- Press ON TIMER button. ON symbol
will be shown on the display with
blinking hour number.
- Press either or button to set the
desired hour.
- Press ON TIMER button again to
conrm hour setting and minute
number will be blinking.
- Press either or button to set the
desired minute.
- Press ON TIMER button again to
conrm minute setting. Hour and
minute number will stop blinking.
The unit is now standby for tarting
air-conditioner automatically at the
set time.
- To cancel ON TIMER, press ON
TIMER button again.
Note:
• The user can conrm ON TIMER
during ON TIMER setting process by
pressing SEND button.
• If there are no other buttons pressed
within 15 seconds, ON TIMER will be
cancelled, and the LCD display will
return to show clock.
• After pressing ON TIMER button,
the LCD display will show the last on
timer set by user with blinking hour
number.
• When ON/OFF TIMER is set, the
present time is not displayed.
• Press CLOCK button to see present
time after ON/OFF TIMER was set.
The LCD display will show present
time about 15 seconds and return to
7
show ON/OFF TIMER. If user press
CLOCK button during the 15 seconds
display of present time, the operation
will be CLOCK setting and return to ON/
OFF TIMER.
• In case of power failure, ON TIMER will
be automatically cancelled as there is no
electricity in the air-conditioner; however,
the set time on the remote control is still
displayed due to batteries. The user has
to cancel and set ON TIMER again or
press SEND button to reactivate ON
TIMER when the electricity is back to
normal conditions.
OFF TIMER Setting
You can set OFF TIMER to stop the unit
automatically at any desired time up to
24 hours as real time.
- Press OFF TIMER button. OFF
symbol will be shown on the display
with blinking hour number.
- Press either or button to set the
desired hour.
- Press OFF TIMER button again to
conrm hour setting and minute
number will be blinking.
- Press either or button to set the
desired minute.
- Press OFF TIMER button again to
conrm minute setting. Hour and
minute number will stop blinking.
The unit is now standby for stopping
airconditioner automatically at the set
time.
- To cancel OFF TIMER, press OFF
TIMER button again.
Note:
• The user can conrm OFF TIMER
during OFF TIMER setting process by
pressing SEND button.
• If there are no other buttons pressed
within 15 seconds, OFF TIMER will
be cancelled, and the LCD display will
return to show clock.
• After pressing OFF TIMER button, the
LCD display will show the last o timer
set by user with blinking hour number.
• When ON/OFF TIMER is set, the
present time is not displayed.
• Press CLOCK button to see present
time after ON/OFF TIMER was set.
The LCD display will show present
time about 15 seconds and return to
show ON/OFF TIMER. If user press
CLOCK button during the 15 seconds
display of present time, the operation
will be CLOCK setting and return to
ON/OFF TIMER.
• In case of power failure, OFF TIMER will
be automatically cancelled as there is no
electricity in the air-conditioner; however,
the set time on the remote control is still
displayed due to batteries.The user has to
cancel and set OFF TIMER again or press
SEND button to reactivate OFF TIMER
when the electricity is back to normal
conditions.
POWERCOOL Mode
POWERCOOL mode rapidly maximizes
the cooling capacity in COOL or DRY mode.
With this simply mode, the user can easily
get the maximum cooling capacity and
comfort.
- Press POWERCOOL button.
“POWERCOOL” will be shown on the
display.
- The air-conditioner will accelerate
capacity up totally 20 minutes or until
room temperature is lower than 18ºC.
- When POWERCOOL mode completely
operates or is cancelled, “POWERCOOL”
will be disappeared from the display
and return to the former settings before
POWERCOOL mode.
- To cancel POWERCOOL mode, press
POWERCOOL or MODE button again.
Note:
• The LCD display will not show fan
speed and set temperature.
• Fan speed and set temperature cannot
be changed while POWERCOOL
mode is selected.
• In case of power failure,
POWERCOOL mode will be
automatically cancelled.
UNT-SVU002-EN
Wireless Remote Control
SLEEP Mode
SLEEP mode automatically and
gradually adjusts room temperature to
provide great comfort during your rest.
- Press SLEEP button, will be
shown on the display.
- After one hour operation of SLEEP
mode, the unit will automatically
raise set temperature by 0.5ºC.
- After one and half hour operation
of SLEEP mode, the unit will
automatically raise set temperature
by 0.5ºC again and on the
display will disappear.
- To cancel SLEEP mode, press
SLEEP mode button again.
Note:
• Set temperature shown on the
display still show the setting without
1ºC added/reduced but it will plus/
minus 1ºC in the memory.
• will disappear from the LCD
display when SLEEP mode
completely operates, after one and
half hours, or is cancelled.
• In case of power failure, SLEEP
mode will be automatically
cancelled.
ECONO Mode
ECONO mode drastically saves energy
with high ecient cooling capacity in COOL
mode by reducing power consumption.
With this simply mode, the user can easily
get energy saving and comfort.
- Press ECONO button. “ECONO”
will be shown on the display.
- The air-conditioner will operates
at low fan speed and raise
temperature by 1ºC from set
temperature.
UNT-SVU002-EN
- To cancel ECONO mode, press
ECONO or MODE button again.
Note:
• ECONO mode operates only in
COOL mode and automatically
operates when air-conditioner is
closed without exitingor canceling
ECONO mode.
• Fan speed can not be changed
while ECONO mode is selected.
SWEEP Function
SWEEP function swiftly distributes
air ow and helps provide better air
circulation in the room with comfortable
cooling.
- Press SWEEP button, “SW” will be
shown on the display.
- The air-conditioner will
automatically sweep the supply air
grille back and forth.
- To cancel SWEEP function, press
SWEEP or LOUVER button again.
Note:
• The supply air grille will be fully
closed when the unit is o.
• The supply air grille will be fully
opened when the unit is on.
• The supply air grille will
automatically stop sweeping when
compressor stops operating and
reactivate SWEEP function once
compressor becomes operating.
• SWEEP function is available only
from 12,000 to 36,000 Btu/h.
LOUVER Function
LOUVER function provides you 5 levels
of air ow direction as your desire with
comfortable cooling.
- Press LOUVER button to select the
desired air ow direction.
Note:
• SWEEP function will be cancelled in
case LOUVER is selected.
• LOUVER function is available only
from 12,000 to 36,000 Btu/h.
FRONT BLADE Function
FRONT BLADE function oers you the
optional supply air grille increasing
air ow direction and circulation with
comfortable cooling or heating.
- Press FRONT BLADE button to
open or close front supply air grille.
Note:
• The front supply air grille will
automatically open when airconditioner
is closed without closing FRONT
BLADE function during the operation.
• FRONT BLADE function is available
only from 12,000 to 36,000 Btu/h.
LIGHT Button
LIGHT button oers you the optional
feature to lighten the LCD display at
any time as you desire.
- Press LIGHT button to lighten the
LCD display for 5 seconds.
Note:
• Whenever you press any button from
6.00 pm to 6.00 am, the LCD display
will automatically be lightened.
SEND Button
SEND button oers you the optional
feature to activate or conrm the
operations shown on the LCD display.
- Press SEND button to activate or
conrm the operations shown on
the LCD display.
Note:
• Whenever you press any button from
6.00 pm to 6.00 am, the LCD display
will automatically be lightened.
ºC/ºF Toggle
The optional feature oers you to
change the temperature display from
ºC to ºF or from ºF to ºC.
- Press and hold SEND button for
5 seconds to change temperature
display.
8
Digital Wired Control
Name and function of buttons
1. Infrared Signal Receiver
Receives the signal from handheld
remote control and transmits the
signal to indoor unit.
2. POWER Button
Press this button to start unit
operation.
Press this button again to stop unit
operation.
3. Temperature Setting Button
TEMP : Press this button to
increase the set temperature.
TEMP : Press this button to
decrease the set temperature.
4. MENU Button
Press this button to select modes
or functions in the menu.
5. MODE Button
Press this button to select system
operation mode. In cooling only
system, a mode is selected in
sequence as FAN, COOL, DRY,
and back to FAN.
6. FAN SPEED Button
Press this button to select fan
speed.
Indicators on Digital Wired
Control
1. CLOCK
Displays present time.
2. ON TIMER
Display ON TIMER when ON
TIMER is set.
3. OFF TIMER
Display OFF TIMER when OFF
TIMER is set.
4. SLEEP Mode
Display sleep symbol after
activating SLEEP mode.
5. Room & Set Temperature
- Displays the room temperature.
When FAN or TURBO mode is
selected, the room temperature
will be disappeared until FAN or
TURBO mode is cancelled or
complete.
- Displays the set temperature
(15ºC to 30ºC) when either or
button is pressed.
6. FAN Speed
Display the selected fan speed
level: auto, low, medium, or high.
7. Operation Mode
Displays the current operation
mode: FAN, COOL, or DRY in
cooling only system.
8. ECONO Mode
Displays “ECONO” when ECONO
mode is activated.
9. TURBO Mode
Displays “TURBO” when TURBO
mode is activated.
10. SWEEP Function
Displays sweep symbol when
sweep motor is activated.
11. Compressor Status Indicator
Displays compressor status.
Operation Mode
FAN Mode
- Press Mode button to select the
operation mode.
- will be shown on the display
when FAN mode is selected.
- Press FAN SPEED button to select
the desired fan speed level and the
display will show.
Auto, Low, Medium, and High respectively
Note:
• In FAN mode, the LCD display
will not show set temperature and
cannot adjust set temperature,
SLEEP, ECONO, and TURBO
mode.
COOL Mode
- Press Mode button to select the
operation mode.
- will be shown on the display
when COOL mode is selected.
- Press either or button to set
the desired temperature between
15ºC to 30ºC.
- Press FAN SPEED button to select
the desired fan speed level and the
display will show.
Auto, Low, Medium, and High respectively
9
UNT-SVU002-EN
Digital Wired Control
DRY Mode
- Press Mode button to select the
operation mode.
- will be shown on the display when
DRY mode is selected.
- Press either or button to set the
desired temperature between 15ºC
to 30ºC.
- Press FAN SPEED button to select
the desired fan speed level and the
display will show.
Auto, Low, Medium, and High respectively
Note:
• In DRY mode, if the compressor
stops working, fan motor and SWEEP
function will be stopped; fan motor and
SWEEP function will operate when
compressor operates.
• ECONO mode can not be activated
during DRY mode operation.
CLOCK Setting
- Press MENU button and select CLOCK
setting by pressing either or .
- Press MENU button again to set clock
and will be shown on the display
with blinking hour number.
- Press either or button to set the
clock to the present hour.
- Press MENU button again to conrm
hour setting and minute number will
be blinking.
- Press either or button to set the
clock to the present minute.
- Press MENU button again to conrm
minute setting; hour and minute
number will stop blinking and the set
time will be shown on the display.
Note:
• If there are no other buttons pressed
within 15 seconds, clock setting will be
cancelled.
Timer Operation
Once you select the timer operation,
the settings are saved in the control.
Thereafter, the air-conditioner will start
operating under the same conditions
when you simply push the POWER
button on the control.
ON TIMER Setting
You can set ON TIMER to start the unit
automatically at any desired time up to
24 hours as real time.
- Press MENU button and select ON
TIMER setting by pressing either or .
- Press Menu button again to set ON
TIMER and ON symbol will be shown on
the display with blinking hour number.
- Press either or button to set the
desired hour.
- Press MENU button again to conrm
hour setting and minute number will
be blinking.
- Press either or button to set the
desired minute.
- Press MENU button again to conrm
minute setting. Hour and minute
number will stop blinking. The unit is
now standby for starting air-conditioner
automatically at the set time.
- To cancel ON TIMER, select ON
TIMER setting and press MENU
button again.
Note:
• If there are no other buttons pressed
within 15 seconds, ON TIMER will be
cancelled, and the LCD display will
return to show clock.
• After selecting ON TIMER setting, the
LCD display will show the last on timer
set by user with blinking hour number.
• When ON/OFF TIMER is set, the
present time is not displayed.
• In case of power failure, ON TIMER will
be automatically cancelled as there is
no electricity in the air-conditioner.
OFF TIMER Setting
You can set OFF TIMER to start the unit
automatically at any desired time up to
24 hours as real time.
- Press MENU button and select OFF
TIMER setting by pressing either or .
- Press Menu button again to set OFF
TIMER and OFF symbol will be
shown on the display with blinking
hour number.
- Press either or button to set the
desired hour.
- Press MENU button again to conrm
hour setting and minute number will
be blinking.
- Press either or button to set the
desired minute.
- Press MENU button again to conrm
minute setting. Hour and minute
number will stop blinking. The unit
is now standby for starting airconditioner automatically at the set
time.
- To cancel OFF TIMER, select OFF
TIMER setting and press MENU
button again.
Note:
• If there are no other buttons pressed
within 15 seconds, OFF TIMER will
be cancelled, and the LCD display will
return to show clock.
• After selecting OFF TIMER setting, the
LCD display will show the last o timer
set by user with blinking hour number.
• When ON/OFF TIMER is set, the
present time is not displayed.
• In case of power failure, OFF TIMER
will be automatically cancelled as
there is no electricity in the airconditioner.
TURBO Mode
TURBO mode rapidly maximizes the
cooling capacity in COOL or DRY mode.
With this simply mode, the user can
easily get the maximum cooling capacity
and comfort.
- Press MENU button and select
TURBO mode setting by pressing
either or .
- The air-conditioner will accelerate
capacity up totally 20 minutes or until
room temperature is lower than 18ºC.
UNT-SVU002-EN
10
Digital Wired Control
- When TURBO mode completely
operates or is cancelled,
“TURBO” will be disappeared
from the display and return to the
former settings before TURBO
mode.
- To cancel TURBO mode, either
press MODE button or select
TURBO mode and press MENU
button again.
Note:
• The LCD display will not show fan
speed and set temperature.
• Fan speed and set temperature
cannot be changed while TURBO
mode is selected.
• In case of power failure, TURBO
mode will be automatically
cancelled.
SLEEP Mode
SLEEP mode automatically and
gradually adjusts room temperature to
provide great comfort during your rest.
- Press MENU button and select
SLEEP mode by pressing either
or .
- Press Menu button again to
conrm SLEEP mode. will be
shown on the display.
- After one hour operation
of SLEEP mode, the unit
will automatically raise set
temperature by 0.5ºC.
- After one and half hour
operation of SLEEP mode, the
unit will automatically raise set
temperature by 0.5ºC again and
on the display will disappear.
- To cancel SLEEP mode, either
press MODE button or select
SLEEP mode and press MENU
button again.
Note:
• Set temperature shown on the
display still show the setting
without 1ºC added/reduced but it
will plus/minus 1ºC in the memory.
• will disappear from the LCD
display when SLEEP mode
completely operates, after one and
half hours, or is cancelled.
• In case of power failure, SLEEP
mode will be automatically
cancelled.
ECONO Mode
ECONO mode drastically saves
energy with high ecient cooling
capacity in COOL mode by reducing
power consumption. With this simply
mode, the user can easily get energy
saving and comfort.
- Press MENU button and select
ECONO mode by pressing either
or .
- Press MENU button again to
conrm ECONO mode. “ECONO”
will be shown on the display.
- The air-conditioner will operates at
low fan speed and raise temperature
by 1ºC from set temperature.
- To cancel ECONO mode, either
press MODE button or select
ECONO mode and press MENU
button again.
Note:
• ECONO mode operates only in
COOL mode and automatically
operates when air-conditioner is
closed without exiting or canceling
ECONO mode.
• Fan speed cannot be changed
while ECONO mode is selected.
SWEEP Function
SWEEP function swiftly distributes
air ow and helps provide better
air circulation in the room with
comfortable cooling or heating.
- Press MENU button and select
SWEEP function by pressing
either or .
- Press MENU button again to
conrm SWEEP function. will
be shown on the display.
- The air-conditioner will
automatically sweep the supply
air grille back and forth.
- To cancel SWEEP function,
select SWEEP function and press
MENU button again.
Note:
• The supply air grille will be fully
closed when the unit is o.
• The supply air grille will be fully
opened when the unit is on.
• The supply air grille will
automatically stop sweeping when
compressor stops operating and
reactivate SWEEP function once
compressor becomes operating.
• SWEEP function is available only
from 12,000 to 36,000 Btu/h.
ºC/ºF Toggle
The optional feature oers you to
change the temperature display from
ºC to ºF or from ºF to ºC.
- Press and hold both and
button for 5 seconds to change
temperature display.
11
UNT-SVU002-EN
System Operation
System Features
1. Watchdog
There is a circuit in the system to
watch the operation of the
microprocessor.
2. Compressor Delay Protection
There is a time delay for restarting
the compressor.
3. Compressor Minimum on Time
Once the compressor starts, it will
operate at least 24 seconds.
4. Non-Volatile Memory
(Auto Restart)
If there is a power interruption or
failure and back to normal, the
control will automatically resume
its operation with the same setting
parameters except those related to
time.
5. Freeze Function
To prevent the indoor coil freezing,
this feature will stop compressor
when the indoor coil temperature is
below 0ºC.
6. Defrost Function
This feature will protect the system
operating in heat mode under very
low ambient temperature.
7. Compressor Status Indicator
This feature is the basic detection
of compressor status by showing
on the display while compressor is
operating.
Error Code & Display
Operating Precautions
The air conditioner must be properly
installed by a qualied installer
in accordance with installation
instructions.
UNT-SVU002-EN
Anti-Recycle Timer
- The control system has a builtin 3 minutes anti-recycle timer
which helps to preserve the life of
system components.
- Anti-recycle timer will operates as
circumstances occur while the air
conditioner is operating:
• Temperature setting is adjusted
back and forth.
• ON/OFF switch is turned ON or
OFF.
• Room temperature reaches the
set point.
• Power failure.
Once one of the above conditions
occurs, the anti-recycle timer will start
preventing the outdoor unit operation
for approximately 3 minutes.
Freeze Protection
The system is protected against low
indoor coil temperatures. Under
certain conditions, the LED indicating
the protective function has been
activated will blink, together with
error code 01 shown on the display.
System adjustment is not necessary.
Stop the air conditioner at once if
any of the followings occurs:
- The power cord is too hot to be
touched by hand.
- The insulation of the power cord
is exposed at any point.
- The fuse is blown or circuit
breaker trips frequently.
- Malfunction or abnormal situation
of the air conditioning system
occurs such as a burning smell.
- Do not inspect or service the air
conditioner while it is operating. Turn
o the power supply before doing
any inspection or service work.
- The power cord should be kept
away from furniture with sharp
corners. It may cause re or
electric shock.
- When the air conditioner will not
used for a long time, be sure to
turn OFF the power supply.
If you have any questions or
problems with your air conditioning
system, please consult your nearest
Trane dealer.
Adjust Air Flow Direction
- The supply air grille may be
adjusted left, right, up or down
manually.
- Adjust the air ow direction
properly, otherwise, it may cause
discomfort and make the room
temperature uneven.
Adjust Air Flow Direction
(with sweep option)
- The sweep motor will sweep
the supply air grille upward and
downward.
- For left and right air ow, the
supply air grille can be adjusted
manually.
12
Electronic Room Thermostat
1) Power Button
Push power button to position to
turn on the air condition, and push
to position to turn o the air
condition and push to position to sw
turn on SWEEP Function.
2) Fan Button
Three fan speed ( high,
medium, low) can be selected
by push the button to the desired
position.
3) Temperature Setting
Temperature setting can be set in
the range of 16°C 30°C by rotating
the temperature setting knob to the
position .
4) Compressor Status Indicator
When compressor of the air
condition operates, the display lamp
will be shown.
13
UNT-SVU002-EN
Maintenance
Regular Maintenance
Be sure to disconnect the power
before inspection or maintenance of
air conditioner.
1. Cleaning the air lter
Air ow is reduced and cooling
eciency impaired if the lter is
clogged. Be sure to clean the
lter every two weeks during the
cooling season.
1.1 How to remove the air lters
- Remove each return air
grille by pushing down and
pulling forward.
- Remove each air lter
frame from the return air
grille.
1.2 How to clean the air lter
Wash away dust from the air lter
with clean water or vacuum it
with an electric vacuum cleaner.
Note: Once the air lter is washed,
dry it completely before returning it
to its original position.
After cleaning, be sure to return it to
its original position.
Cautions
- Do not wash the air lter in water
that is over 40ºC or it may shrink.
- Do not expose the air lter to re.
- Do not expose the air lter to
direct sunlight for a long time.
- Clean the air lter more frequently
when the air is very dirty.
2. Cleaning the front panel
Do not pour water directly on the
front panel to clean it. Dust or wipe
it lightly with a soft cloth. If it is very
dirty, use a soft cloth soaked in
water or neutral detergent.
Cautions
- Do not use water over 50ºC to
clean the front panel or it may
become discolored.
- Do not use benzine, gasoline,
thinner, polishing compound,
machine oil, etc. when cleaning
the front panel, or paint may peel
o, or it may become deformed or
damaged.
3. Maintenance before prolonged
idle period
- Operate the fan for about half a
day to dry the inside of the unit.
- Stop the air conditioner and
disconnect the power by
turning o the safety breaker.
- Clean the air lter and return it
to its original position.
UNT-SVU002-EN
14
Troubleshooting
Before calling for service, please
check the following.
The air conditioner does not
operate at all:
- Check if the control ON/OFF
switch is “OFF”. Turn the switch
to ON.
- Check whether the fuse has been
blown or circuit breaker thrown.
Set the ON/OFF Control Switch
to OFF, and turn on the circuit
breaker or replace to a new fuse.
- Check whether the power supply
is interrupted. Wait until the power
is resupplied and then operate the
air conditioner.
Cooling is insucient:
- Check whether the air lter is
clogged. Clean it.
- Check whether the thermostat
setting is too high. Set the
thermostat to lower temperature.
- Check whether windows or doors
are opened. If opened, close
them.
- Check whether there are sources
of heat in the room, cooling is less
eective.
- Check whether the return air
grille or the supply air grille on
the indoor unit and outdoor unit
are blocked. If they are blocked,
remove obstacles to permit air
passage properly.
- Check whether the fan speed is
set at low. Set the fan switch from
“LOW” to “MED” or “HIGH”.
15
UNT-SVU002-EN
Trane do Brasil
Av. dos Pinheirais, 565 - Estação
83.705-570 - Araucária, PR - Brasil
Literature Order Number: UNT-SVU002-EN
Date: Mar 2008
Supersedes: June 2017
Stocking Location: Bangkok, Thailand
www.trane.com.br
For more information, contact your
local district oce
Trane has a policy of continuous product and product data improvement and reserves the right to
change design and specications without notice. Only qualied technicians should perform the installation
and servicing of equipment referred to in this publication.
Loading...