Trane CenTraVac CDHG, CenTraVac CDHF, CenTraVac CVHF, CenTraVac CVHE, CenTraVac CVHG Assembly/disassembly Manual

Disassembly and Reassembly Units

Water-Cooled CenTraVac™ Chillers

50 Hz Models: CDHG, CVHE, CVHG 60 Hz Models: CDHF, CVHE, CVHF

X39640718110

SSAAFFEETTYY WWAARRNNIINNGG

Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person could result in death or serious injury. When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that are attached to the equipment.

January 2019

CCVVHHEE--SSVVNN0044MM--EENN

Introduction

WARNING

CAU

TION

NOTICE

Read this manual thoroughly before operating or servicing this unit.

Warnings, Cautions, and Notices

Safety advisories appear throughout this manual as required. Your personal safety and the proper operation of this machine depend upon the strict observance of these precautions.

The three types of advisories are defined as follows:

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. It could also be used to alert against unsafe practices.

Indicates a situation that could result in equipment or property-damage only accidents.

Important Environmental Concerns

Scientific research has shown that certain man-made chemicals can affect the earth’s naturally occurring stratospheric ozone layer when released to the atmosphere. In particular, several of the identified chemicals that may affect the ozone layer are refrigerants that contain Chlorine, Fluorine and Carbon (CFCs) and those containing Hydrogen, Chlorine, Fluorine and Carbon (HCFCs). Not all refrigerants containing these compounds have the same potential impact to the environment. Trane advocates the responsible handling of all refrigerants-including industry replacements for CFCs and HCFCs such as saturated or unsaturated HFCs and HCFCs.

Important Responsible Refrigerant Practices

Trane believes that responsible refrigerant practices are important to the environment, our customers, and the air conditioning industry. All technicians who handle refrigerants must be certified according to local rules. For the USA, the Federal Clean Air Act (Section

608) sets forth the requirements for handling, reclaiming, recovering and recycling of certain refrigerants and the equipment that is used in these service procedures. In addition, some states or municipalities may have additional requirements that must also be adhered to for responsible management of refrigerants. Know the applicable laws and follow them.

WWAARRNNIINNGG

PPrrooppeerr FFiieelldd WWiirriinngg aanndd GGrroouunnddiinngg RReeqquuiirreedd!!

FFaaiilluurree ttoo ffoollllooww ccooddee ccoouulldd rreessuulltt iinn ddeeaatthh oorr sseerriioouuss iinnjjuurryy.. AAllll ffiieelldd wwiirriinngg MMUUSSTT bbee ppeerrffoorrmmeedd bbyy qquuaalliiffiieedd ppeerrssoonnnneell.. IImmpprrooppeerrllyy iinnssttaalllleedd aanndd ggrroouunnddeedd ffiieelldd wwiirriinngg ppoosseess FFIIRREE aanndd EELLEECCTTRROOCCUUTTIIOONN hhaazzaarrddss.. TToo aavvooiidd tthheessee hhaazzaarrddss,, yyoouu MMUUSSTT ffoollllooww rreeqquuiirreemmeennttss ffoorr ffiieelldd wwiirriinngg iinnssttaallllaattiioonn aanndd ggrroouunnddiinngg aass ddeessccrriibbeedd iinn NNEECC aanndd yyoouurr llooccaall// ssttaattee//nnaattiioonnaall eelleeccttrriiccaall ccooddeess..

WWAARRNNIINNGG

PPeerrssoonnaall PPrrootteeccttiivvee EEqquuiippmmeenntt ((PPPPEE)) RReeqquuiirreedd!!

FFaaiilluurree ttoo wweeaarr pprrooppeerr PPPPEE ffoorr tthhee jjoobb bbeeiinngg uunnddeerrttaakkeenn ccoouulldd rreessuulltt iinn ddeeaatthh oorr sseerriioouuss iinnjjuurryy.. TTeecchhnniicciiaannss,, iinn oorrddeerr ttoo pprrootteecctt tthheemmsseellvveess ffrroomm ppootteennttiiaall eelleeccttrriiccaall,, mmeecchhaanniiccaall,, aanndd cchheemmiiccaall hhaazzaarrddss,, MMUUSSTT ffoollllooww pprreeccaauuttiioonnss iinn tthhiiss mmaannuuaall aanndd oonn tthhee ttaaggss,, ssttiicckkeerrss,, aanndd llaabbeellss,, aass wweellll aass tthhee iinnssttrruuccttiioonnss bbeellooww::

•• BBeeffoorree iinnssttaalllliinngg//sseerrvviicciinngg tthhiiss uunniitt,, tteecchhnniicciiaannss MMUUSSTT ppuutt oonn aallll PPPPEE rreeqquuiirreedd ffoorr tthhee wwoorrkk bbeeiinngg uunnddeerrttaakkeenn ((EExxaammpplleess;; ccuutt rreessiissttaanntt gglloovveess//sslleeeevveess,, bbuuttyyll gglloovveess,, ssaaffeettyy ggllaasssseess,, hhaarrdd hhaatt//bbuummpp ccaapp,, ffaallll pprrootteeccttiioonn,, eelleeccttrriiccaall PPPPEE aanndd aarrcc ffllaasshh ccllootthhiinngg)).. AALLWWAAYYSS rreeffeerr ttoo aapppprroopprriiaattee MMaatteerriiaall SSaaffeettyy DDaattaa SShheeeettss ((MMSSDDSS))//SSaaffeettyy DDaattaa SShheeeettss ((SSDDSS)) aanndd OOSSHHAA gguuiiddeelliinneess ffoorr pprrooppeerr PPPPEE..

•• WWhheenn wwoorrkkiinngg wwiitthh oorr aarroouunndd hhaazzaarrddoouuss cchheemmiiccaallss,, AALLWWAAYYSS rreeffeerr ttoo tthhee aapppprroopprriiaattee MMSSDDSS//SSDDSS aanndd OOSSHHAA//GGHHSS ((GGlloobbaall HHaarrmmoonniizzeedd SSyysstteemm ooff CCllaassssiiffiiccaattiioonn aanndd LLaabbeelllliinngg ooff CChheemmiiccaallss)) gguuiiddeelliinneess ffoorr iinnffoorrmmaattiioonn oonn aalllloowwaabbllee ppeerrssoonnaall eexxppoossuurree lleevveellss,, pprrooppeerr rreessppiirraattoorryy pprrootteeccttiioonn aanndd hhaannddlliinngg iinnssttrruuccttiioonnss..

•• IIff tthheerree iiss aa rriisskk ooff eenneerrggiizzeedd eelleeccttrriiccaall ccoonnttaacctt,, aarrcc,, oorr ffllaasshh,, tteecchhnniicciiaannss MMUUSSTT ppuutt oonn aallll PPPPEE iinn aaccccoorrddaannccee wwiitthh OOSSHHAA,, NNFFPPAA 7700EE,, oorr ootthheerr ccoouunnttrryy--ssppeecciiffiicc rreeqquuiirreemmeennttss ffoorr aarrcc ffllaasshh pprrootteeccttiioonn,, PPRRIIOORR ttoo sseerrvviicciinngg tthhee uunniitt.. NNEEVVEERR PPEERRFFOORRMM AANNYY SSWWIITTCCHHIINNGG,, DDIISSCCOONNNNEECCTTIINNGG,, OORR VVOOLLTTAAGGEE TTEESSTTIINNGG WWIITTHHOOUUTT PPRROOPPEERR EELLEECCTTRRIICCAALL PPPPEE AANNDD AARRCC FFLLAASSHH CCLLOOTTHHIINNGG.. EENNSSUURREE EELLEECCTTRRIICCAALL MMEETTEERRSS AANNDD EEQQUUIIPPMMEENNTT AARREE PPRROOPPEERRLLYY RRAATTEEDD FFOORR IINNTTEENNDDEEDD VVOOLLTTAAGGEE..

CVHE-SVN04M-EN

IInnttrroodduuccttiioonn

WWAARRNNIINNGG

FFoollllooww EEHHSS PPoolliicciieess!!

FFaaiilluurree ttoo ffoollllooww iinnssttrruuccttiioonnss bbeellooww ccoouulldd rreessuulltt iinn ddeeaatthh oorr sseerriioouuss iinnjjuurryy..

•• AAllll IInnggeerrssoollll RRaanndd ppeerrssoonnnneell mmuusstt ffoollllooww IInnggeerrssoollll RRaanndd EEnnvviirroonnmmeennttaall,, HHeeaalltthh aanndd SSaaffeettyy ((EEHHSS)) ppoolliicciieess wwhheenn ppeerrffoorrmmiinngg wwoorrkk ssuucchh aass hhoott wwoorrkk,, eelleeccttrriiccaall,, ffaallll pprrootteeccttiioonn,, lloocckkoouutt//ttaaggoouutt,, rreeffrriiggeerraanntt hhaannddlliinngg,, eettcc.. AAllll ppoolliicciieess ccaann bbee ffoouunndd oonn tthhee BBOOSS ssiittee.. WWhheerree llooccaall rreegguullaattiioonnss aarree mmoorree ssttrriinnggeenntt tthhaann tthheessee ppoolliicciieess,, tthhoossee rreegguullaattiioonnss ssuuppeerrsseeddee tthheessee ppoolliicciieess..

•• NNoonn--IInnggeerrssoollll RRaanndd ppeerrssoonnnneell sshhoouulldd aallwwaayyss ffoollllooww llooccaall rreegguullaattiioonnss..

This document and the information in it are the property of Trane, and may not be used or reproduced in whole or in part without written permission. Trane reserves the right to revise this publication at any time, and to make changes to its content without obligation to notify any person of such revision or change.

Trademarks

All trademarks referenced in this document are the trademarks of their respective owners.

Revision History

• Update to Figure 1, p. 10

• Update to Figure 2, p. 11

Factory Warranty Information

Compliance with the following is required to preserve the factory warranty:

AAllll UUnniitt IInnssttaallllaattiioonnss

Startup MUST be performed by Trane, or an authorized agent of Trane, to VALIDATE this WARRANTY. Contractor must provide a two-week startup notification to Trane (or an agent of Trane specifically authorized to perform startup).

AAddddiittiioonnaall RReeqquuiirreemmeennttss ffoorr UUnniittss RReeqquuiirriinngg DDiissaasssseemmbbllyy aanndd RReeaasssseemmbbllyy

When a new chiller is shipped and received from our Trane manufacturing location and, for any reason, it requires disassembly or partial disassembly, and reassembly— which could include but is not limited to the evaporator, condenser, control panel, compressor/ motor, economizer, purge, factory-mounted starter or any other components originally attached to the fully assembled unit— compliance with the following is required to preserve the factory warranty:

• Trane, or an agent of Trane specifically authorized to perform start-up and warranty of Trane® products, will perform or have direct on-site technical supervision of the disassembly and reassembly work.

• The installing contractor must notify Trane—or an agent of Trane specifically authorized to perform startup and warranty of Trane® products—two weeks in advance of the scheduled disassembly work to coordinate the disassembly and reassembly work.

• Start-up must be performed by Trane or an agent of Trane specifically authorized to perform startup and warranty of Trane® products.

Trane, or an agent of Trane specifically authorized to perform start-up and warranty of Trane® products, will provide qualified personnel and standard hand tools to perform the disassembly and reassembly work at a location specified by the contractor. The contractor shall provide the rigging equipment such as chain falls, gantries, cranes, forklifts, etc. necessary for the disassembly and reassembly work and the required qualified personnel to operate the necessary rigging equipment.

CVHE-SVN04M-EN

General Information

WWAARRNNIINNGG

RReeffrriiggeerraanntt MMaayy BBee UUnnddeerr PPoossiittiivvee PPrreessssuurree!!

FFaaiilluurree ttoo ffoollllooww iinnssttrruuccttiioonnss bbeellooww ccoouulldd rreessuulltt iinn aann eexxpplloossiioonn wwhhiicchh ccoouulldd rreessuulltt iinn ddeeaatthh oorr sseerriioouuss iinnjjuurryy oorr eeqquuiippmmeenntt ddaammaaggee.. SSyysstteemm ccoonnttaaiinnss rreeffrriiggeerraanntt aanndd mmaayy bbee uunnddeerr ppoossiittiivvee pprreessssuurree;; ssyysstteemm mmaayy aallssoo ccoonnttaaiinn ooiill.. RReeccoovveerr rreeffrriiggeerraanntt ttoo rreelliieevvee pprreessssuurree bbeeffoorree ooppeenniinngg tthhee ssyysstteemm.. SSeeee uunniitt nnaammeeppllaattee ffoorr rreeffrriiggeerraanntt ttyyppee.. DDoo nnoott uussee nnoonn--aapppprroovveedd rreeffrriiggeerraannttss,, rreeffrriiggeerraanntt ssuubbssttiittuutteess,, oorr nnoonn-aapppprroovveedd rreeffrriiggeerraanntt aaddddiittiivveess..

NNOOTTIICCEE

EEqquuiippmmeenntt DDaammaaggee!!

MMiixxiinngg rreeffrriiggeerraannttss oorr ooiillss ccoouulldd rreessuulltt iinn eeqquuiippmmeenntt ddaammaaggee iinncclluuddiinngg bbeeaarriinngg ddaammaaggee,, iinnttrroodduuccttiioonn ooff aacciiddss iinnttoo tthhee cchhiilllleerr,, oorr ccoonnttiinnuuoouuss ppuurrggee ppuummpp--oouutt iinn hhiigghh--hheeaadd//hhiigghh aammbbiieenntt aapppplliiccaattiioonnss.. CCeennTTrraaVVaacc cchhiilllleerrss aarree mmaannuuffaaccttuurreedd wwiitthh ddiiffffeerreenntt rreeffrriiggeerraanntt//ooiill ssyysstteemmss:: 11)) cchhiilllleerrss uussiinngg RR--112233 rreeffrriiggeerraanntt aanndd OOIILL0000002222 ccoommpprreessssoorr ooiill,, aanndd 22)) cchhiilllleerrss uussiinngg RR--551144AA rreeffrriiggeerraanntt aanndd OOIILL0000333344//OOIILL0000333355 ccoommpprreessssoorr ooiill.. VVeerriiffyy pprrooppeerr rreeffrriiggeerraanntt aanndd ooiill ffoorr yyoouurr cchhiilllleerr aanndd ddoo NNOOTT mmiixx rreeffrriiggeerraannttss oorr ooiillss!!

This Installation, Operation, and Maintenance manual applies to CenTraVac™ chillers with two different refrigerant and oil systems:

• R-123 and OIL00022

• R-514A and OIL00334/OIL00335

IImmppoorrttaanntt:: Verify proper refrigerant and oil for your

chiller before proceeding!

The information and procedures in this document are to facilitate unit disassembly for clearance and access reasons during the installation process.

The understanding is that the chiller has what is referred to as the “compressor doweling option” or “separable shell option” (which includes compressor doweling). Compressor doweling sets up the compressor for removal. The separable shell option includes a bolt together design between the evaporator and condenser and allows the shells to be separated in the field.

IImmppoorrttaanntt:: These procedures do NOT apply to units

that have been installed and electrical supply wiring has been completed.

Contractor Responsibilities

WWAARRNNIINNGG

HHeeaavvyy OObbjjeeccttss!!

FFaaiilluurree ttoo ffoollllooww iinnssttrruuccttiioonnss bbeellooww ccoouulldd rreessuulltt iinn ccoommppoonneenntt ddrrooppppiinngg wwhhiicchh ccoouulldd rreessuulltt iinn ddeeaatthh oorr sseerriioouuss iinnjjuurryy,, aanndd eeqquuiippmmeenntt oorr pprrooppeerrttyy--oonnllyy ddaammaaggee.. LLooaaddss ccaann sshhiifftt aanndd bbeeccoommee ooffff--cceenntteerr dduurriinngg sshhiippppiinngg.. EEnnssuurree tthhaatt ccoommppoonneennttss aarree cceenntteerreedd bbeeffoorree lliiffttiinngg aanndd aallwwaayyss tteesstt lliifftt eeaacchh ccoommppoonneenntt ttoo vveerriiffyy cceenntteerr ooff ggrraavviittyy uussiinngg lliiffttiinngg eeqquuiippmmeenntt rraatteedd ffoorr tthhee ttaasskk.. OOnnllyy eexxppeerriieenncceedd rriiggggeerrss sshhoouulldd ppeerrffoorrmm uunniitt ddiissaasssseemmbbllyy//rreeaasssseemmbbllyy..

• Handle/lift and rig equipment

• Protect all internal components from exposure to elements, which could contaminate or corrode chiller components

• Chiller reassembly

• Replace all gaskets with new gaskets or O-rings and sealing compound; the contractor should assist a qualified Trane Technician with this responsibility

NNOOTTIICCEE

CCoommpprreessssoorr DDaammaaggee!!

PPOOEE ooiill iiss hhyyggrroossccooppiicc –– iitt aabbssoorrbbss wwaatteerr ddiirreeccttllyy ffrroomm tthhee aaiirr.. TThhiiss wwaatteerr iiss nneeaarrllyy iimmppoossssiibbllee ttoo rreemmoovvee ffrroomm tthhee ccoommpprreessssoorr ooiill aanndd ccaann rreessuulltt iinn ccoommpprreessssoorr ffaaiilluurreess.. TToo pprreevveenntt PPOOEE ooiill ffrroomm aabbssoorrbbiinngg wwaatteerr,, tthhee ssyysstteemm sshhoouulldd nnoott rreemmaaiinn ooppeenn ffoorr lloonnggeerr tthhaann nneecceessssaarryy.. WWhheenn ooppeenn,, ddrryy nniittrrooggeenn sshhoouulldd ffllooww tthhrroouugghh tthhee ppiippiinngg.. OOnnllyy nneeww ooiill ccoonnttaaiinneerrss sshhoouulldd bbee uusseedd ffoorr sseerrvviiccee aanndd mmaaiinntteennaannccee.. AAllwwaayyss uussee tthhee ssmmaalllleesstt ccoonnttaaiinneerr ssiizzee rreeqquuiirreedd ffoorr tthhee jjoobb rreeqquuiirreemmeennttss.. AAllwwaayyss lleeaavvee tthhee ooiill ccoonnttaaiinneerr ttiigghhttllyy sseeaalleedd uunnttiill ttiimmee ooff uussee.. DDoo nnoott rreeuussee ooiill tthhaatt hhaass bbeeeenn ooppeenneedd..

• Change the compressor oil; the contractor should assist a qualified Trane Technician with this responsibility

• Evacuate the chiller under 1000 microns; the contractor should assist a qualified Trane Technician with this responsibility

• Recharge the chiller with dry nitrogen to 5 psig; the contractor should assist a qualified Trane Technician with this responsibility

• Replace and/or repair insulation

• Reconnect electrical connections

• Spot paint the chiller if necessary

CVHE-SVN04M-EN

GGeenneerraall IInnffoorrmmaattiioonn

Metric Conversions

English Metric

ft·lb x 1.3558 Newton·meter

lb x 0.4536 kg

in x 25.4000 mm

Device Descriptions

Device Description

CPTF

FRCL Optional free cooling

HGBP Optional hot gas bypass

INDP Optional industrial control package

SMP Optional supplemental motor protection

UAFD Unit-mounted Adaptive Frequency™ drive

UATR

UPIR

UXL

USID Unit-mounted low-voltage solid state starter

USTR Unit-mounted low-voltage wye-delta starter

Optional control power transformer (INDP units only)

(INDP units only)

Unit-mounted medium-voltage auto transformer Unit-mounted medium-voltage primary reactor Unit-mounted medium-voltage across-theline starter

CVHE-SVN04M-EN

Dimensions and Weights

Dimensions

Single Compressor Chillers: Models CVHE, CVHF, and CVHG

The following table shows dimensional data for Figure

1, p. 10 and Figure 2, p. 11.

Table 1. Dimensional data for CVHE, CVHF, and CVHG CenTraVac chillers

Model NTON Shell Size

190–270 032 320 66.7 53.1

230–320 050 320 75.4 53.6

CVHE

CVHF

300–420 050 500 73.7 52.7

360–500 080 500 93.5 77.1 101.3 42.0 87.8 51.7 58.6 93.8 45.5 62.2 63.5 44.3

300–450

350–570

620–870

650–910

1070–1300

1470–1720

050/080

050 480 75.4 52.7

050/080

080 480 93.5 75.7 101.3 42.0 78.3 51.3 59.1 93.8 45.5 62.2 63.5 44.3

080 870 93.5 75.0 101.3 42.0 81.2 59.7 73.2 93.8 45.5 63.9 63.5 44.3

080/142

142 870 98.1 80.4 121.9

080 910

080/142

142 910 98.1 83.0 111.0

080/142

142 1300 120.9 80.4 121.9

142/210

210 1300 106.5 94.5 116.0

250 1300 120.9 98.6 121.9

142/210

210 1720 106.5 92.8 116.0

250 1720 120.9 96.9 121.9

Comp

Size

500 84.1 66.0 90.4 42.0 87.8 51.7 58.6 82.7 46.0 54.9 49.32 41.3

480 84.1 64.6 90.4 42.0 78.3 51.3 59.1 82.7 46.0 54.9 49.32 41.3

870 101.3 79.4 107.5

910 101.3 79.4 107.5

1300 102.2 80.5 107.5

1300 106.0 88.2 109.7

1720 106.0 86.5 109.7

A B C D E F G H J K L M

93.5

N/A N/A

(b)

76.5 101.3 42.0 81.2 54.6 66.7 93.8 45.5 63.9 63.5 44.3

84.9 49.2 49.7 70.8 45.5 53.1 37.9 34.5

73.4 49.2 52.4 77.1 45.5 52.5 43.9 38.7

87.8 51.7 54.4 77.1 45.5 52.5 42.3 38.7

78.3 51.3 54.4 77.1 45.5 52.5 43.9 38.7

(a)

81.3 59.7 73.2 102.0 45.5 67.9 63.59 46.0

(a)

81.2 59.7 73.2 110.9 46.9 65.4 62.5 50.5

(a)

81.3 54.6 66.7 102.0 45.5 64.6 63.59 46.0

(a)

81.2 54.6 66.7 105.5 46.9 69.8 62.5 46.0

(a)

80.5 59.1 72.4 102.0 45.5 65.7 63.59 46.0

(a)

80.2 54.6 72.6 110.9 46.9 64.2 76.5 50.5

(a)

80.5 59.1 72.4 105.4 46.9 73.1 62.5 52.4

(a)

80.2 59.7 72.6 116.4 50.5 84.5 68.2 50.5

(a)

80.2 59.7 72.6 116.4 54.5 84.5 76.7 56.6

(a)

93.8 63.1 75.6 105.4 46.9 73.1 62.5 52.4

(a)

91.2 63.1 75.6 110.9 50.5 78.2 68.2 50.5

(a)

91.2 63.1 75.6 116.4 54.5 84.4 76.7 56.6

CVHE-SVN04M-EN

Table 1. Dimensional data for CVHE, CVHF, and CVHG CenTraVac chillers (continued)

Model NTON Shell Size

050 565 75.4 52.6

480–565

080 565 93.5 74.6 101.3 42.0 94.3 53.0 62.8 93.8 45.5 62.2 63.5 44.3

050/080

080 780 93.5 76.5 101.3 42.0 94.0 54.3 66.6 93.8 45.5 63.9 63.5 44.3

670–780

080/142

142 780 98.1 83.0 111.0

CVHG

920–1067

080/142

142 920 98.1 84.0 111.0

142/210

210 920 106.5 96.0 116.0

080/142

1100

142 1100 98.8 80.4 107.4

142/210

210 1100 106.5 94.5 116.0

Note: All dimensions are in inches (±0.5 inch).

(a)

Does not extend beyond the condenser tube unit.

(b)

Add 1 in. to overall width for compressor.

(c)

Add 0.4 in. to overall width for compressor.

Comp

Size

A B C D E F G H J K L M

N/A N/A

565

63.4 90.2 42.0 94.5 52.9 62.8 82.7 46.0 57.6 49.32 40.0

(c)

82.6

780 101.3 79.4 107.5

920 102.2 82.0 107.5

920 106.0 89.7 109.7

1100 102.2 80.5 107.5

1100 106.0 88.2 109.7

93.8 53.0 57.5 77.1 45.5 52.5 43.9 38.7

(a)

91.9 54.3 66.6 102.0 45.5 66.8 63.59 46.0

(a)

94.0 54.3 66.6 105.5 46.9 69.8 62.5 46.0

(a)

90.9 54.6 68.7 102.0 45.5 64.3 63.59 46.0

(a)

93.2 54.3 68.0 105.5 46.9 69.8 62.5 46.0

(a)

93.3 54.6 68.7 105.4 46.9 76.2 62.5 52.4

(a)

93.2 54.3 68.0 110.9 50.5 81.5 68.2 50.5

(a)

93.2 59.1 72.4 102.0 45.5 65.7 63.59 46.0

(a)

93.2 59.7 71.8 101.9 46.9 62.0 62.3 46.0

(a)

93.2 59.1 72.4 105.4 46.9 76.2 62.5 52.4

(a)

93.2 59.7 72.6 110.9 50.5 78.2 68.2 50.5

DDiimmeennssiioonnss aanndd WWeeiigghhttss

The following table shows dimensional data for Figure

1, p. 10 and Figure 2, p. 11.

CVHE-SVN04M-EN

DDiimmeennssiioonnss aanndd WWeeiigghhttss

Table 2. Dimensional data for CVHE, CVHF, and CVHG CenTraVac chillers

Exp

Model NTON Shell Size

190–270 032 320 60.1 71.4 81.9 29.7 17.0 26.5 68.6 93.9 47.0 47.0

230–320 050 320 64.6 71.4 81.9 29.7 17.0 23.4 80.5 98.4 63.4 54.9

CVHE

CVHF

CVHG

300–420 050 500 62.8 71.4 81.9 29.8 17.3 26.5 80.5 98.7 63.4 54.9

360–500 080 500 79.0 71.4 81.9 29.8 17.3 26.5 97.1 114.9 80.8 80.8 66.3

300–450

350–570

620–870

650–910

1070–1300

1470–1720

480–565

670–780

920–1067

1100

Note: All dimensions are in inches (±0.5 inch).

050/080

050 480 64.3 71.4 81.9 29.0 16.3 26.5 80.5 100.0 60.7 54.9

050/080

080 480 79.0 71.4 81.9 29.0 16.3 26.5 97.1 114.9 75.0 75.0 66.3

080 870 75.7 71.4 81.9 30.5 17.8 29.0 97.1 117.1 82.4 82.4 63.9

080/142

142 870 93.8 72.8 83.3 30.5 17.8 29.0 117.4 121.5 82.4 82.4 72.7

080 910 75.7 71.4 81.9 30.5 17.8 29.0 97.1 114.9 82.4 82.4 63.9

080/142

142 910 82.1 72.8 83.3 30.5 17.8 29.0 115.4 121.3 84.4 84.4 72.7

080/142

142 1300 93.8 72.8 83.3

142/210

210 1300 93.8 76.4 86.9

250 1300 97.9 80.4 90.9

142/210

210 1720 92.6 76.4 86.9

250 1720 96.8 80.4 90.9

050 565 66.4 71.4 81.9 32.4 19.9 26.5 80.5 103.0 63.4 54.9

080 565 68.4 71.8 82.3 32.4 19.9 29.0 91.4 104.7

050/080

080 780 75.7 71.4 81.9 33.5 21.1 32.8 98.1 114.7 82.4 82.4

080/142

142 780 82.1 72.8 83.3 27.8 17.8 32.8 115.4 121.2 84.4 84.4

080/142

142 920 82.1 72.8 83.3 28.0 18.0 36.8 115.4 121.2 84.4 84.4

142/210

210 920 93.8 76.4 86.9 33.7 21.3 36.8 124.7 132.8 92.9 92.9

080/142

142 1100 80.1 72.8 83.3 28.0 18.0 36.8 117.4 121.5 78.1 78.1 72.7

142/210

210 1100 93.8 76.4 86.9 33.7 21.3 36.8 124.7 135.2 87.2 87.2 82.4

Comp

Size

500 68.1 71.8 82.3 29.0 16.3 26.5 90.1 103.8

480 68.1 71.8 82.3 29.0 16.3 26.5 90.1 103.7

870 79.0 71.3 81.8

910 79.0 71.3 81.8

1300 80.5 71.3 81.8

1300 87.7 72.8 83.3

1720 86.5 72.8 83.3

565 79.2 71.4 81.9 33.6 21.2 29.0 98.1 115.8 81.7 81.7

780 79.0 71.3 81.8

920 80.5 71.3 81.8

920 87.7 72.8 83.3

1100 80.5 71.3 81.8

1100 87.7 72.8 83.3

Std

P W

R S T U V

N/A

18.5 29.0 120.9 121.6

N/A

18.5 29.0 120.9 117.8

N/A

18.6 36.8 121.8 121.6

N/A

21.1 36.8 117.4 121.5 78.1 78.1 72.7

N/A

21.1 36.8 126.9 129.0

N/A

21.1 36.8 124.7 135.2 87.2 87.2 82.4

N/A

18.6 36.8 137.2 139.4

N/A

25.8 36.8 126.9 130.9

N/A

25.8 33.3 124.7 137.2 92.9 92.9 76.4

N/A

23.3 33.3 137.2 141.4

N/A

18.5 32.8 120.9 117.6

N/A

18.6 36.8 121.8 119.4

N/A

21.3 36.8 126.9 126.7

N/A

18.6 36.8 121.8 121.6

N/A

21.3 36.8 126.9 129.0

Short

Long

N/A N/A N/A

N/A N/A

N/A N/A N/A

N/A N/A

N/A

72.7

82.7

72.7

82.7

N/A

72.7

N/A

72.7

N/A

72.7

N/A

72.7

The following table shows dimensional data for Figure

1, p. 10 and Figure 2, p. 11.

CVHE-SVN04M-EN

Table 3. Dimensional data for CVHE, CVHF and CVHG CenTraVac chillers

Model NTON Shell Size

Comp

Size

190–270 032 320 79.8

230–320 050 320 94.1

CVHE

300–420 050 500 92.5

360–500 080 500

300–450

050/080

500

050 480 92.7

350–570

050/080

480

080 480

080 870

620–870

080/142

870

142 870

080 910

CVHF

650–910

080/142

142 910

080/142

910

1300

142 1300

1070–1300

142/210

1300

210 1300

250 1300 140.7

1470–1720

142/210

210 1720

1720

250 1720 140.7

050 565 93.3

480–565

080 565

050/080

565

080 780

670–780

080/142

780

142 780

CVHG

920–1067

080/142

142 920

142/210

920

210 920

1100

080/142

142 1100

142/210

1100

210 1100

Notes:

1. Refer to Table 5, p. 13.

2. All dimensions are in inches (±0.5 inch).

(a)

When indicated, see Note 1 (above).

(b)

Does not extend beyond the main unit control panel.

UATR

USID

UPIR

USTR

UXL

Y1 Y2 Y1 Y2 AD Y1 Y2 AD

N/A

(a) (a) (a) (a)

N/A

(a) (a) (a) (a)

(b)

(a) (a) (a) (a)

(a)

N/A

(a) (a) (a) (a)

USID USTR

49.1

57.5

55.9

56.1

80.2

56.6

UATR UPIR

UXL

N/A

405–608A 900–1210A

94.9 64.2

101.2 64.6

110.6 77.0

111.5 70.63

N/A

101.2 64.6

111.5 70.63

110.6 77.0

125.8 92.2 7.0 133.3 99.8 4.8

140.0 81.75

139.9 77.5

119.3 85.7

132.7 75.33

130.4 77.5

140.0 81.75

139.9 77.5

147.9 83.6 3.5 154.9 90.6 5.6

N/A N/A N/A

(a)

N/A N/A N/A

(a)

N/A N/A N/A

N/A N/A N/A N/A N/A N/A N/A

N/A N/A N/A N/A N/A N/A

DDiimmeennssiioonnss aanndd WWeeiigghhttss

AFDE UAFD

N/A N/A N/A N/A

N/A

147.0 88.8 5.8

N/A

144.0 91.0 4.6

N/A

126.8 93.3 4.8

N/A

146.2 88.8 5.8

N/A

144.0 91.0 4.6

N/A

147.0 88.8 6.3

N/A

146.0 91.0 4.6

152.4 95.9 3.9

160.0 99.5 3.1

155.0 90.7 5.6

152.4 95.9 3.9

160.0 99.5 3.1

See Table 1, p. 6 through for dimensional data regarding the following figure.

CVHE-SVN04M-EN

Y1 Y3

1.6 405–608A UAFD

1.0 900–1210A UAFD

2.5 318A & 530–636A UAFD

1.00

USID, USTR, OR UACD

PURGE

CVHE

320

FRCL

UATR, UPIR, UXL OR SMP

COMPRESSOR MAX WIDTH

ECONOMIZER

CONDENSER

COMPRESSOR

MOTOR TERMINAL BOX (NOT SHOWN)

PURGE

OPTIONAL USID O

R USTR

SEE UNIT SUBMITTALS FOR DIMENSIONS

OPTIONAL UATR, UPIR, UXL OR SMP SEE UNIT SUBMITTALS FOR DIMENSIONS

MAIN UNIT CONTROL PANEL

OPTIONAL UAFD SEE UNIT SUBMITTALS FOR DIMENSIONS

UAFD DISCONNECT SWITCH TO ENCLOSURE DOOR LATCHES

MAIN UN

IT CONTROL PANEL

UAFD

EVAPO

RATOR

SEE NOTE 4

SMALLEST

MOTOR

1.3

3.0

5.7

OIL FILTER

WHEN CONDENSER IS WIDEST

MAIN CONTROL PANEL

OPTIONAL CPTR

CPTR LIFTING LUG

WHEN OIL TANK IS WIDEST

MOTOR SUPPORT

EVAPORATOR

CONDENSER

PURGE

CVHF-080 UNIT SHOWN (COOLING ONLY) WITH COMPRESSOR AND ECONOMIZER REMOVED

DDiimmeennssiioonnss aanndd WWeeiigghhttss

Figure 1. Assembly for CVHE, CVHF, and CVHG CenTraVac chillers

NNootteess::

1. All dimensions are in inches (±0.5 inch). See Table 1, p. 6 through Table 5, p. 13 for dimension tables.

2. UAFD brackets and supports shown are bolt-on and removable. Most brackets and supports on 405–608A UAFD are welded on and non-removable. See Table 5, p. 13 for applicable dimensions.

3. Applies only to CVHE 190–320 NTON on 032 shells with free-cooling option.

4. Add 1.5 inch for distance to Tracer AdaptiView

™

display mounting arm in stowed position.

CVHE-SVN04M-EN

See Table 1, p. 6 through for dimensional data for the

MAX OD

LARGEST

TOR

MOTOR

REMOVAL SPACE

OPTIONAL

UATR OR UPIR

REDUCED VOLTAGE

ENCLOSURE

DIMENSIONS: 40.0 W X 26.2 D X 27.0 H WEIGHT: 1200 LBS MAX

MAIN UNIT

CONTROL PANEL

COMPRESSOR

MOTOR

LARGEST MOTOR

OPTIONAL

CPTR

SHORT SHELL

LONG SHELL

.100

CVHF-080 UNIT SHOWN (COOLING ONLY)

1.6 405-608A UAFD

1.0 900-1210A UAFD

2.5 339A & 539-677A UAFD

OPTIONAL USID OR USTR SEE UNIT SUBMITTALS FOR DIMENSIONS

OIL FILTER

USID, USTR, OR UACD

MAIN UNIT CONTROL PANEL

SUPPORTS FOR OPTIONAL UNIT MOUNTED UATR OR UPIR REDUCED VOLTAGE ENCLOSURE (ENCLOSURE NOT SHOWN)

WHEN CONDENSER IS WIDEST

OPTIONAL FRCL CONNECTION

PURGE

WHEN OIL TANK IS WIDEST

CONDENSER

UAFD

MOTOR SUPPORT

OPTIONAL UATR, UPIR, UXL OR SMP SEE UNIT SUBMITTALS FOR DIMENSIONS

MAIN UNIT CONTROL PANEL

OPTIONAL UAFD SEE UNIT SUBMITTALS FOR DIMENSIONS

UAFD DISCONNECT SWITCH TO ENCLOSURE DOOR LATCHES

UATR, UPIR, UXL OR SMP

EVAPORATOR

following figure.

Figure 2. Assembly for CVHE, CVHF, and CVHG CenTraVac chillers (CVHF-080 shown)

DDiimmeennssiioonnss aanndd WWeeiigghhttss

NNootteess::

1. All dimensions are in inches (±0.5 inch). See Table 1, p. 6 through Table 5, p. 13 for dimension tables.

2. UAFD brackets and supports shown are bolt-on and removable. Most brackets and supports on 405–608A UAFD are welded on and non-removable. See Table 5, p. 13 for application dimensions.

3. Applies only to CVHE 190–320 NTON on 032 shells with free-cooling option.

4. Add 1.5 inch for distance to Tracer Adaptiview

™

display mounting arm in stowed position.

CVHE-SVN04M-EN

+ 25 hidden pages

Trane CenTraVac CDHG, CenTraVac CDHF, CenTraVac CVHF, CenTraVac CVHE, CenTraVac CVHG Assembly/disassembly Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

General Information

Contractor Responsibilities

Metric Conversions

Device Descriptions

Dimensions and Weights

Dimensions

Single Compressor Chillers: Models CVHE, CVHF, and CVHG