Trail Tech Striker CR2032, Vapor Quick Start Manual

3. VEHICLE SENSORS:

Refer to the sensor installation sections.
You should install the wheel sensor,
engine temperature sensor, and
vehicle power connection.

010-ELV-196

QUICK-START

1. POWER OVERVIEW

2. MOUNT STRIKER:

4. INDICATOR LIGHTS:

5. SLEEP MODE:

6. MAINTENANCE ICONS AND LO BATTERY:

Striker operates on the internal 3.0V watch type battery
(#CR2032). If possible, install Striker to the vehicle’s
electrical system. Striker is polarity independent and has
safeguards to avoid draining the vehicle battery. See the
POWER CONNECTION section for more info.

Installing the power wire enables a brighter backlight,
longer sleep timer, and the voltage and
temperature indicator LED’s.

Striker is made to be bolted to the vehicle. Use
the included handlebar mounts, or refer to the
manual.

Striker has two colored LED lights at the top. They are activated when temperature goes above the threshold, or voltage goes below threshold,
to warn you about potential problems with your vehicle. The left LED is yellow, the right LED is red. When the voltage is low the LED will flash, if
the temperature is high then the LED will turn on solid. Set custom thresholds in the DATA SETTING MODE.

Set the thresholds to 0 to turn them off.

If Striker sees no activity (either wheel movement or a button press) for 5 minutes, it will enter sleep mode and only display the clock. Sleep
mode will end when any activity is noticed. During sleep mode Striker is using the internal battery and will not draw down vehicle power.

There are two separate maintenance timers: a WRENCH and an OIL CAN. Set the mileage in DATA SETTING MODE, then Striker will
countdown the miles. When the mileage countdown reaches 0, the icon is displayed. If the internal watch battery voltage gets too low, then
Striker displays a LO icon.

Aluminum

Protector Mount

(optional)

Temperature

Sensor (varies)

Power Wire Wheel Speed

Sensor (varies)

Included

Handlebar

Mount

QUICK-START

9. DATA SETTING MODE :

HOLD DOWN ALL 3 BUTTONS to enter data setting mode.
Adjust one setting at a time, then move on to the next one.

<LEFT> = Scroll value.
<MODE> = Move to next data setting screen.
<RIGHT> = Move to next digit in data setting mode.

7. BUTTONS:

8. SCREENS:

Striker has three screens. Press MODE to toggle between them.

Striker has 3 screens, press MODE to cycle between screens. Hold all three buttons to enter data setting mode.

RESET TRIP DATA:

<LEFT> + <MODE> = HOLD TO RESET VALUES FOR:
Max Speed, Distance, Ride Time, Stop Watch, Max Engine
Temperature, and Max Voltage.

ADJUST TRIP DISTANCE:

<MODE> + 3 sec = ENTER ADJUST MODE
<LEFT>, <RIGHT> = SCROLL VALUE

ORDER OF SETUP MODE:

1. Speed and Distance Format

2. Wheel Size

3. Time Format

4. Time of Day

5. Temperature Unit of Measure

6. Temperature Indicator

7. Temperature Indicator Danger

8. Voltage Indicator

9. Voltage Indicator Danger

10. Oil Maintenance

11. Care Maintenance

12. Average Speed Screen

13. Distance Resolution

M/H or KM/H
See MEASURE WHEEL SIZE section
12H or 24H
12:00:00
°F or °C
Yellow Indicator
Red Indicator
Yellow Indicator
Red Indicator
Distance Countdown
Distance Countdown
Show on Screen 2 or 3
Show 1 or 2 Digits After Decimal

SCREEN 1

• Speed

• Trip Distance

• Clock

• Voltage

• Engine Temperature

• Ride Time

SCREEN 2

• Speed

• Trip Distance

• Clock

• Voltage

• Air Temp

• Stop Watch (TT)

Average speed can be set to show on
screen 2 rather than screen 3, see DATA
SETTING MODE.

SCREEN 3

• Avg Speed

• Max Speed

• Odometer

• Clock

• Accum. Ride TIme

• Max Voltage

• Min Voltage

• Max Engine Temp

Striker alternately displays min/max voltage
and avg/max speed every 2 seconds.

YELLOW

LED

LEFT BUTTON

Start stop watch

MODE BUTTON

Switch screens

RIGHT BUTTON

Backlight

RED
LED