Trail Tech 5203-00 User Manual

5203-00/5203-10 KICKSTAND INSTALLATION
‘06-’09 YZ 250F/450F AND 07-09 WRF 250/450
5203-PK CONTENTS:
FIG. 1
5203-PK Parts Kit
A. 5905-04 Kickstand Spring
B. 5903-00 Hanger Tab
YAMAHA YZ 250F/450F ‘06-’09
1. Remove stock foot-peg, foot-peg
hardware, & foot-peg hanger from frame.
2. Install provided Trail Tech foot-peg bracket, using the OEM fasteners.
Note: Use thread locking compound and manufacturers torque specification during installation.
3. Re install foot peg & foot-peg hardware following manufacturers recommended installation procedure.
4. Remove the stock side panel fastener and insert through the provided spring hanger tab (Fig. 1)
TRAIL TECH KICKSTANDS
010-ELV-137
Tech Support: 360-687-4530
tech_support@trailtech.net
FIG. 2
5203-00 Kickstand Installed
5. Re-install the side panel fastener, and tighten down hand tight to start.
Note: Do not tighten down to manufacturers torque specification until spring is hung. Failure to do so may cause your spring to bind or break during use!
6. Hook spring into spring hanger mounting tab shown in (Fig. 2)
7. Using safety glasses & a spring puller stretch the spring and latch it onto the stand arm mounting point (Fig. 2)
8. Tighten sub-frame fastener to manufacturers torque specification.
Continued on other side >>
IMPORTANT: WEAR EYE PROTECTION WHEN HANGING SPRINGS!
Note: After every ride it is important to check your kickstand thoroughly for the following:
• Loose or damaged bolts • Bent or damaged kickstand leg or bracket • Damaged spring
Damaged or broken parts can result in serious injury! If any part of your stand has become
damaged do not ride the machine! Contact a factory trained technician or Trail Tech directly for service or repairs.
TRAIL TECH INC. WARRANTS TRAIL TECH KICKSTAND PRODUCTS TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP UNDER NORMAL USE AND IF PROPERLY
INSTALLED FOR A PERIOD OF SIX MONTHS FROM DATE OF PURCHASE. IF FOUND TO BE DEFECTIVE AS MENTIONED ABOVE, IT WILL BE REPLACED OR REPAIRED. THIS SHALL
CONSTITUTE THE SOLE REMEDY OF THE PURCHASER AND THE SOLE LIABILITY OF TRAIL TECH INC. TO THE EXTENT PERMITTED BY LAW, THE FOREGOING IS EXCLUSIVE
AND IN LIEU OF ALL OTHER WARRANTIES OR REPRESENTATIONS WHETHER EXPRESSED OR IMPLIED, INCLUDED ANY LIMITED WARRANTY OF MERCHANTABILITY OR FITNESS.
IN NO EVENT SHALL TRAIL TECH INC. BE LIABLE FOR SPECIAL OR CONSEQUENTIAL DAMAGES.
LIMITED WARRANTY
5204-00/5204-10 KICKSTAND INSTALLATION
‘10-’14 YZ 250F/450F
5204-PK CONTENTS:
FIG. 1 FIG. 2
5. Re-install the side panel fastener, and
YAMAHA YZ 250F/450F ‘10-’14
1. Remove stock foot-peg, foot-peg
hardware, & foot-peg hanger from frame.
2. Install provided Trail Tech foot-peg bracket, using the OEM fasteners.
Note: Use thread locking compound and manufacturers torque specification during installation.
3. Re install foot peg & foot-peg hardware following manufacturers recommended installation procedure.
4. Remove the stock side panel fastener and insert through the provided spring hanger tab (Fig. 1)
tighten down hand tight to start.
Note: Do not tighten down to manufacturers torque specification until spring is hung. Failure to do so may cause your spring to bind or break during use!
6. Hook spring into spring hanger mounting tab shown in (Fig. 2)
7. Using safety glasses & a spring puller stretch the spring and latch it onto the stand arm mounting point (Fig. 2)
8. Tighten sub-frame fastener to manufacturers torque specification.
TRAIL TECH KICKSTANDS
010-ELV-137
Tech Support: 360-687-4530
tech_support@trailtech.net
5204-00 Kickstand Installed
Continued on other side >>
IMPORTANT: WEAR EYE PROTECTION WHEN HANGING SPRINGS!
Note: After every ride it is important to check your kickstand thoroughly for the following:
• Loose or damaged bolts • Bent or damaged kickstand leg or bracket • Damaged spring
Damaged or broken parts can result in serious injury! If any part of your stand has become
damaged do not ride the machine! Contact a factory trained technician or Trail Tech directly for service or repairs.
TRAIL TECH INC. WARRANTS TRAIL TECH KICKSTAND PRODUCTS TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP UNDER NORMAL USE AND IF PROPERLY
INSTALLED FOR A PERIOD OF SIX MONTHS FROM DATE OF PURCHASE. IF FOUND TO BE DEFECTIVE AS MENTIONED ABOVE, IT WILL BE REPLACED OR REPAIRED. THIS SHALL
CONSTITUTE THE SOLE REMEDY OF THE PURCHASER AND THE SOLE LIABILITY OF TRAIL TECH INC. TO THE EXTENT PERMITTED BY LAW, THE FOREGOING IS EXCLUSIVE
AND IN LIEU OF ALL OTHER WARRANTIES OR REPRESENTATIONS WHETHER EXPRESSED OR IMPLIED, INCLUDED ANY LIMITED WARRANTY OF MERCHANTABILITY OR FITNESS.
IN NO EVENT SHALL TRAIL TECH INC. BE LIABLE FOR SPECIAL OR CONSEQUENTIAL DAMAGES.
LIMITED WARRANTY
Loading...