TP-Link TL-MC1400, TL-FC1420 Installation Guide

Installation Guide

14-Slot Rackmount Chassis

Package Contents: Chassis, AC Power Cord, Fourteen Retainer-plates, Installation Guide

The pictures are for demonstration purposes only. The actual product may dier in appearance from the depicted.

To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community. For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.

If you have any suggestions or needs on the product guides, welcome to email techwriter@tp-link.com.cn.

Installation

Step 1: Install the Media Converters in the Chassis

Note:

It is recommended to use TP-Link media converters. Other vendors’ products may be incompatible.

1. Tweak out the two screws on the media converter. Then install the retainer-plate (provided with the chassis) to the media converter using the screws removed from the media converter.

Step 3: Mount the Chassis on the Rack

Note:

1. The chassis supports EIA standard-sized, 19-inch racks.

2. For security reasons, it is recommended to install the chassis as shown below.

Fasten the chassis to the rack with screws through the holes of the brackets on each side.

2. Remove the front metal plate of the slot on the chassis, then carefully slide the media converter into the slot and lock it tightly with the locking knob.

Step 2: (Optional) Install the Redundant Power Supply Module

Remove the protective cover on the power supply module slot of the chassis. Then gently push in the module and plug it solidly into the connector.

Chassis

Step 4: Power On

1. Electrically connect the Grounding Terminal on the rear panel of the chassis to ground via the ground cable.

Grounding Terminal

2. Connect the chassis to the AC outlet using the provided power cord.

Panel Layout

Power LED

FAN LED

Grounding Terminal FAN

Note: An optional AC or DC power supply is available for installation in the optional power supply position.

AC Power Plug

LED Explanation

Power

On: Power on

O:

Power o

Optional Power Supply Position

FAN

On: The fans are working properly.

O:

The fans are working abnormally.

Specications

Specifications Environmental and Physical Specifications

Input: 100–240 V ~ 50/60 Hz 1.8 A (Max)

AC Power Supply

DC Power Output per Slot

Dimensions (W×D×H)

Output: 12 V, 6.25 A (Max) Ripple & Noise: < 180 mV (0˚C to 50˚C);

< 250 mV (-10˚C to 0˚C)

TL-MC1400: 9 V/0.6 A TL-FC1420: 5 V/0.6 A

Power, FANLED

482 × 309 × 86 mm

Ye sHot-swappable

Ye sOverload Protection

Safety Information

Keep the device away from water, re, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.

Avoid using this product during an electrical storm. There may be a remote risk of electric shock from

lightning.

The label is placed on the bottom surface of the product.

Place the device with its bottom surface downward.

The socket-outlet shall be installed near the equipment and shall be easily accessible.

Operation Temperature TL-MC1400: 0˚C to 40˚C (32˚F to 104˚F)

TL-FC1420: 0˚C to 50˚C (32˚F to 122˚F)

Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F)

Operation Humidity 10% to 90% RH non-condensing

Storage Humidity 5% to 90% RH non-condensing

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other

relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.

The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.

Please read and follow the above safety information when operating the device. We cannot guarantee

that no accidents or damage will occur due to improper use of the device. Please use this product

with care and operate at your own risk.