TP-Link TL-FC311A-2, TL-FC111B-20, TL-FC311B-2, TL-FC311A-20, TL-FC311B-20 User Manual
Enlarge Your Ethernet Network
Gigabit WDM Media Converter
Package Contents: Converter, Power Adapter, Installation Guide
LED Explanation
PWR
On: Power on
Off:Power off
Link/Act
On: Valid link
Flashing: Transmitting or receiving data Off: Invalid link
Scenario 1: Connect Devices with and without Optical Interfaces
Ethernet Device |
Media Converter |
Ethernet Device |
with Optical Interfaces |
|
without Optical Interfaces |
|
PWR |
|
1000BASE-X (Fiber) Interface |
Gigabit Ethernet |
Gigabit Ethernet |
|
|
<![endif]>0.0.REV1 7106508920 Link-TP ©2020
LC-SC Fiber Cable |
Twisted-Pair Cable |
Scenario 2: Connect Devices without Optical Interfaces
Ethernet Device |
Media Converter |
Media Converter |
Ethernet Device |
without Optical Interfaces |
|
|
without optical Interfaces |
GigabitEthernet
Gigabit Ethernet
PWR
PWR
Gigabit Ethernet
Gigabit Ethernet
Twisted-Pair Cable |
SC-SC Fiber Cable |
Twisted-Pair Cable |
Note: Please use one TL-FC311A-2 and one TL-FC311B-2 together to work properly.
Please use one TL-FC311A-20 and one TL-FC311B-20 together to work properly.
Specifications
General Specifications
Standards |
IEEE 802.3, IEEE 802.3i, IEEE 802.3u, |
|
IEEE 802.3ab, IEEE 802.3x, IEEE 802.3z |
||
|
||
LED |
PWR, Link/Act |
|
Connector |
1 SC fiber optic; 1 RJ45 jack |
|
Twisted-Pair |
100BASE-Tx: 2-pair UTP/STP of Cat. 5 or above (≤100 m) |
|
1000BASE-Tx: 4-pair UTP/STP of Cat. 5e or above (≤100 m) |
||
|
||
Fiber |
9/125 μm single-mode fiber |
|
Transmission |
TL-FC311A-2/TL-FC311B-2: ≤2 km |
|
Distance |
TL-FC311A-20/TL-FC311B-20: ≤20 km |
|
Wave Length |
TL-FC311A-2/TL-FC311A-20: 1550 nm Tx, 1310 nm Rx |
|
TL-FC311B-2/TL-FC311B-20: 1310 nm Tx 1550 nm Rx |
||
|
||
Power |
External Power Adapter: 5 V/0.6 A |
|
Dimensions |
94.5x73x27 mm |
Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Do not point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight
Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact us. .
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
Environmental and Physical Specifications
Operating Temperature |
0˚C to 50˚C (32˚F to 122˚F) |
Storage Temperature |
-40˚C to 70˚C (-40˚F to 158˚F) |
Operating Humidity |
10% to 90% RH non-condensing |
Storage Humidity |
5% to 90% RH non-condensing |
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.
If you have any suggestions or needs on the product guides, welcome to email techwriter@tp-link.com.cn.
EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
Loading...