LED Explanation
7106508579 REV3.0.0
Installation Guide
JetStream Gigabit Smart PoE+ Switch
Connection
PoE MAX
On: 51 W≤Total power supply<58 W
Flashing: Total power supply keeps≥
51 W more than 2 minutes
O:
Total power supply<51 W
Power
On: Power on
O: Power o
SPF1/SFP2
On (Green): Connected to a 1000 Mbps
device
On (Yellow): Connected to a 100 Mbps
device
Flashing: Transmitting/receiving data
PoE MAX
Power
SPF1 SPF2
Ethernet Ports (1–8)
Link/Act (port 1–8)
On (Green):
On (Yellow): Running at 10/100 Mbps
Flashing: Transmitting/receiving data
Running at 1000 Mbps
System
Flashing: System running normally
On/O: System running abnormally
PoE Status (port 1–8)
On: Providing PoE power
Flashing: Current-overload/Short-circuit/
Connected to a Non-standard PD/Power
exceeded the user-dened value
O: Not providing PoE Power
Link/Act
System
PoE Status
3
1
AC Power Cord
2
DC Power Adapter
Internet
Note:
1. PoE ports can also connect to non-PoE devices, but only transmit data.
2. Maximum PoE power is 30 W for each PoE port and 58 W for all PoE ports.
Conguration
PC
SFP Slots
PoE Devices
IP Camera AP IP Phone
1. To access the GUI of the switch, open a browser and type the default
management address http://192.168.0.1 in the address eld of the
browser, then press the Enter key.
Note:
To log in to the switch, the IP address
of your PC should be set in the same
subnet as that of the switch. The IP
address is 192.168.0.x (”x” is any
number from 2 to 254). Subnet Mask
is 255.255.255.0. For details, please
refer to Appendix B in the User Guide
on the resource CD.
2. Enter admin for both the username
and password in the lower case
letters. Then click the Log In button
or press the Enter key. (The rst time
you log in, change the password to
better protect your network and
devices.)
3. After a successful login, the main
page will appear. You can click the
menus on the top side and left side
to congure the corresponding
functions.
Note:
For more details about how to congure the switch, see the Conguration
Guide on the resource CD.
Specications
Frequently Asked Questions (FAQ)
General Specications
IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3af,
Standard
Data Transfer Rate
Network Media (Cable)
Number of Ports
PoE Ports (RJ45)
LED Indicators
Transfer Method
MAC Address Learning
Frame Forward Rate
IEEE802.3at, IEEE802.3az, IEEE802.3x, IEEE802.3z,
IEEE802.1X, IEEE802.1ab, IEEE802.1ah, IEEE802.1d,
IEEE802.1p, IEEE802.1q, IEEE802.1s, IEEE802.1w
Ethernet:10 Mbps (Half Duplex) 20 Mbps (Full Duplex)
Fast Ethernet: 100 Mbps (Half Duplex)
200 Mbps (Full Duplex)
Gigabit Ethernet: 2000 Mbps (Full Duplex)
10Base-T:
UTP Cat. 3, 4, 5 cable (maximum 100 m) EIA/TIA-568 100 Ω
STP (maximum 100 m)
100Base-TX:
UTP of Cat. 5 or above (maximum 100 m)
EIA/TIA-568 100 Ω STP (maximum 100 m)
1000Base-T:
UTP of Cat. 5e or above (maximum 100 m)
EIA/TIA-568 100 Ω STP (maximum 100 m)
100Base-FX/LX10/BX10: MMF or SMF SFP Module
1000Base-SX/LX/LX10/BX10: MMF or SMF SFP Module
8 10/100/1000 Mbps Auto-Negotiation RJ45 ports and
2 SFP slots
PoE Ports: Port1–8
Total Power Supply: 58 W
Power, System, Link/Act, PoE MAX, PoE Status, SFP1, SFP2
Store and Forward
Automatically learning, automatically aging
10Base-T: 14881 pps/Port
100Base-Tx: 148810 pps/Port
1000Base-T: 1488095 pps/Port
Q1. The Power LED is not lit.
The Power LED should be lit when the power system is working normally. If the Power
LED is not lit, please check as follows:
:
Make sure the AC power cord is connected to the switch with power source
A1
properly.
:
Make sure the voltage of the power supply meets the requirements of the input
A2
voltage of the switch.
:
Make sure the power source is ON.
A3
A4: On the LED On/O conguration page, check whether the LED status is on. By
default, the LED status is on
.
Q2. Why is the Link/Act LED not lit while a device is connected to
the corresponding port?
Please try the following:
Make sure that the cable connectors are rmly plugged into the switch and the
A1:
device.
Make sure the connected device is turned on and works normally.
A2:
A3: Try to change the connected device’s transmission speed and duplex mode.
A4:
The cable must be less than 100 meters long (328 feet).
Environmental and Physical Specications
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
To ask questions, find answers, and communicate with TP-Link users
or engineers, please visit
https://community.tp-link.com to join TP-Link Community.
For technical support, the user guide and other information, please
visit https://www.tp-link.com/support, or simply scan the QR code.
If you have any suggestions or needs on the product guides,
welcome to email techwriter@tp-link.com.cn.
Disclaimer
PoE budget calculations are based on laboratory testing. Actual PoE power budget is not
guaranteed and will vary as a result of client limitations and environmental factors.
EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC,
2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
0 ˚C to 40 ˚C (32 ˚F to 104 ˚F)
-40 ˚C to 70 ˚C (-40 ˚F to 158 ˚F)
10% to 90% non-condensing
5% to 90% non-condensing
Q3. Why are some ports not supplying power for PoE devices?
Please try the following:
A1:
Make sure that this PoE device complies with IEEE 802.3af/IEEE 802.3at.
A2:
Try another PoE port on the switch.
A3:
Pay attention to PoE priority. If the total power consumption of PoE powered
devices exceeds 58 W, a priority will be set among the ports. Ports with a smaller
port number will have higher priority. For example, Port 1, 2 and 5 are each
consuming 15.4 W. If an additional powered device consuming 15 W is connected
to Port 3, then the switch will cut o power to Port 5 because of the overload.
Safety Information
Avoid using this product during an electrical storm. There may be a remote risk of electric
shock from lightning.
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Place the device with its bottom surface downward.
Please read and follow the above safety information when operating the device. We cannot
guarantee that no accidents or damage will occur due to improper use of the device. Please
use this product with care and operate at your own risk.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність
вимогам нормативних документів та вимогам, що передбачені чинними
законодавчими актами України.
© 2020 TP-Link
Loading...