This guide provides a brief introduction to Smart 3-Way Switch Kit and the Kasa app, as well as regulatory information.
Please note that features of Smart 3-Way Switch Kit may vary slightly depending on the model and software version you have, and on your location,
language and internet service provider. All images, parameters and descriptions documented in this guide are used for demonstration only.
Conventions
In this guide, the following convention is used:
Convention Description
Teal
Underline
Key information appears in teal, including management page text such as menus, items, buttons and so on.
Hyperlinks are in teal and underlined. You can click to redirect to a website.
More Info
• Specications can be found on the product page at http://www.tp-link.com
• Our Technical Support and troubleshooting information can be found at http://www.tp-link.com/support.
.
1
Introduction
3-Way Switching, where a light is controlled from two switch locations, is common in hallways, stairs, and living rooms. 3-Way Switch wiring can be
complex, but TP-Link’s Smart 3-Way Switch Kit makes it an easy smart home upgrade and provides control from anywhere, scheduling, and much
more. The Kit includes 2 smart switches specially designed for 3-way switch wiring. The free Kasa app provides step-by-step instructions for wiring
your switches and connecting them to your home Wi-Fi network.
• No Extra Hardware Required - Convenient smart swtiches with no extra hardware required
• Control Your Lights From Anywhere - Control all of your home lighting using the Kasa app
• Hands-free Experience - Control your lights by voice commands through support from Amazon Alexa and Google Assistant
• Scheduling - Program lights to turn o and on at set times throughout the day or night
Phone not included;
Works with iOS and Android
2
Appearance
Smart 3-Way Switch Kit has two LEDs that changes color according to its status, a RESTART button and a RESET button. See the explanation below:
Blinking Amber and Green
App-Cong mode initiated.
Green
Lit up for about 30 seconds when connected to the Wi-Fi network, then turns o.
Blinking Amber
Resetting.
Red
No Wi-Fi connection.
White
Lit up when the light is switched OFF to show the Smart Switch location in the dark.
RESTART
RESET
Press to reboot the Smart Switch.
Press and hold (about 5 seconds) until the Wi-Fi status LED blinks amber and green
alternately to initiate App-Cong mode.
Press and hold (about 10 seconds) until the Wi-Fi status LED blinks amber rapidly to
factory reset the Smart Switch.
3
Set Up Your Smart 3-Way Switch Kit
Follow the steps below to set up your Smart 3-Way Switch Kit via Kasa for Mobile app.
1. Download and install Kasa app
Go to Google Play or the Apple App Store
or scan the QR code below to download the
Kasa app on your Android or iOS smartphone
or tablet.
2. Log in or sign up with TP-Link ID
Open the app. Use your TP-Link ID to log in.
If you don’t have a TP-Link ID, tap Create
Account and the Kasa app will guide you
through the rest.
3. Remove old switches
Find the circuit breaker and turn off the
power. Remove your old switches but do not
disconnect the wires.
4
Set Up Your Smart 3-Way Switch Kit
Follow the steps below to set up your Smart 3-Way Switch Kit via Kasa for Mobile app.
4. Wire your new smart switch kit
Follow the Kasa app instructions to wire your
smart switch kit with the 3-Way wiring method.
Then install and secure both switches after
the wiring.
5. Set up and pair both switches
With your smart switch kit secured, set up
your first switch and then pair your second
one. Make sure they control the same light.
6. Complete and enjoy
Your smart switch kit is all set up and saved in
your device list. You can now enjoy using it
.
5
Main Pages
After you successfully set up your Smart 3-Way Switch Kit, you will see the home page of the Kasa app. Here you can view the working status of all
devices that you've added to Kasa and manage them. Tap on a smart switch to check the current status and runtime of your smart switch kit
.
Home Page
Device Status
6
Congure Your Smart 3-Way Switch Kit
On Device Status page, you can set Schedule, preset Away Mode, set Timer and change the settings of your smart switch kit.
Set Schedule
Tap to set a schedule for your smart switch
kit to simplify your daily routine by creating
automatic On/O action.
Preset Away Mode
Tap to preset the Away Mode and your
smart switch kit will be randomly turned on/o
during this time.
7
Congure Your Smart 3-Way Switch Kit
On Device Status page, you can set Schedule, Away Mode, Timer and change the settings of your smart switch kit.
Set Timer
Tap to set the time to turn your smart switch
kit on or o after specic times.
Device Settings
Tap to view and change the settings of
your smart switch kit.
8
Create Scenes
A scene is a preset group of smart devices that can be programmed, customized and activated simultaneously at the touch of a button from your
smartphone or tablet, allowing you to easily set your mood, activity or t any special occasion. This page allows you to preset how your smart home
devices should act automatically at special occasions.
9
Connect to Amazon Alexa or Google Home
Connect your Smart 3-Way Switch Kit to Amazon Alexa or Google Home to enjoy a full hands-free experience - control your lights by voice commands.
Follow a method below to connect your Smart 3-Way Switch Kit to Amazon Alexa or Google Home.
Method 1:
Launch Kasa app and go to Add Device > WORKS WITH KASA > Amazon Alexa / Google Assistant for detailed instructions.
Method 2:
Visit FAQs on the TP-Link ocial website for detailed instructions:
Google Assistant: www.tp-link.com/us/faq-1534.html
Amazon Alexa: www.tp-link.com/us/faq-944.html
10
Authentication
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product
names are trademarks or registered trademarks of their respective holders.
TP-Link USA Corporation, d/b/a TP-Link North America, Inc.
Address: 145 South State College Blvd. Suite 400, Brea, CA 92821
Website: http://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6803
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications
could void the user’s authority to operate the equipment.
12
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be
co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.”
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards,
FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2018.1.5
13
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes :
1. l’appareil ne doit pas produire de brouillage;
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d’en compromettre le
fonctionnement.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device.
• Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to
improper use of the device. Please use this product with care and operate at your own risk.
Warnings
• Install only in a suitable UL Listed outlet box.
15
• CAUTION - Risk of Electric Shock - More than one disconnect switch may be required to de-energize the equipment before servicing.
• Tighten terminal screws to 13 lbf-in
• Supported specified line number for the thread terminal copper wire: 12AWG and14AWG.
• Supported Load Types:
100-120V~ 15A max, Res
100-120V~ 5A, Incandescent
100-120V~ 5A, Electronic Fluorescent Ballast
• Operating Temperature: 0 ºC-40 ºC (32°F-104°F)
• Operating Humidity: 5%-90%RH, Non-condensing
Explanation of the symbols on the product label
SymbolExplanation
AC voltage
Indoor use only
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to
European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
16
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.