TP-LINK Groovi Ripple Portable Bluetooth Speaker
BS1001
User Manual
Caution: 1) Photos are for reference only, actual product may vary! 2)
TP-LINK is committed to improving product quality and performance,
but product technology and design are subject to change without prior notice .
TP-L INK Gro ovi Rip ple Por table B lueto oth Spe aker
BS1 001
User Ma nual
Cauti on: 1) Ph otos ar e for ref erenc e only, ac tual pr oduct m ay vary ! 2)
TP-LI NK is com mitte d to impr oving p roduc t quali ty and pe rform ance,
but pro duct te chnol ogy and d esign a re subj ect to ch ange wi thout p rior no tice .
CONTENTS IN THE BOX:
1. BS1001: 2.USB charging cable
3. Manual 4. Guarantee card
Important safety instructions:
1. Please carefully read and follow the safety instructions before using the prod uct.
2. Please avoid leaving the product in a damp environment, exposing i t to sunl ight,
or placing it near re.
3. Please do not use the product near water.
4. Please do not place the product near heat-generating appliance s such as a radiator,
air conditioner, or stove.
5. Please use the recommended power voltage.
6. Please do not disassemble the product without authorization.
7. Explosion may occur if battery is replaced incorrectly. Please replace bat tery on ly with
the same or equivalent type.
8. Please avoid leaving the product exposed to sunlight, rain, wate r dropl ets, or a hot or
moist environment.
9. Please enjoy the music at an appropriate volume to protect your health and so und equipment.
10. Please unplug the charging cable when it is not in use.
PRODUCT DESCRIPTION:
Indicate led
1
Power button
2
Vol+ button
3
Vol- button
4
Micro USB charging port
5
3.5 mm audio input interface 3.5mm
6
1
2
4 3
65
TECHNICAL DATA:
Output power: 3.5W
Distortion: ≤1%
Frequency response: 120Hz~20KHz
SNR: >65dB
Speaker unit: 4Ω
Power input: USB/DC 5V
Sensitivity: 600mV
Product size: 88 x 88 x 41mm
Recharging Battery:
1. This product has a built-in rechargeable lithium battery. Plea se conn ect the U SB charging
cable to a workable USB port (a PC/Mac or a USB power adapter).
2. When the battery is low, the red power indicator will turn on.
3. When the speaker is being recharged, the red power indicator truns on. When t he
recharging is completed, the indicator will turn off.
4. When the battery is completely discharged, the product cannot be turned on befor e being
recharged for a while.
The Speaker Paired with a Bluetooth Device (First Connection):
1. Make sure that the product has sucient power or has been connected to power.
2. Short Press the power button.
3. The blue power indicator turns on and the Bluetooth pairing blu e indicator ashes.
4. Start the Bluetooth device (for example, a mobile phone) to searching mod e (just a s you
would when searching for a new Bluetooth device on the phone)
5. “Groovi Ripple” is displayed in the list of Bluetooth devices.
6. Select “Groovi Ripple”. Enter “0000” if prompted to enter a pairing code.
7. The blue LED stops blinking and stays blue. This indicates a succes sful pairing.
8. Check the Bluetooth device to make sure that the connection is successful.
9. Press the power button to turn off the product. The product will shut down automatically
after 30 minutes if no audio input is received.
ATTENTION:
● To connect the product to another Bluetooth device, you must rst disconnect the current
Bluetooth connection. Long Press Power button to enter a new device search ing and pairing
mode.
● When the product is restarted, it will automatically reconnect to the previousl y paire d device
by default. If the automatic connection fails, you need to do the connection manual ly.
AUX IN Mode Operation Instructions:
1. Insert one end of a 3.5 mm stereo audio cable into the “Aux in” interface on the back of this
product.
2. Put the other end of the stereo audio cable into the headphone jack of an externa l audio
device.
Loading...