Enlarge Your Ethernet Network
10/100Mbps WDM Media Converter with 1-Port PoE
Package Contents: Converter, Power Adapter, Installation Guide
LED Explanation
PWR |
|
Link/Act |
|
On: Power on |
|
On: Valid link |
|
Off:Power off |
|
Flashing: Transmitting or receiving data |
|
|
|
Off: Invalid link |
PoE
On: Supplying power normally
Flashing Slowly: No PD is connected
Flashing Quickly: Supplying power abnormally
Off: No power supply
<![endif]>0.0.REV1 7106509098 Link-TP ©2020
Scenario 1: Connect Devices with Optical Interfaces
Ethernet Device |
Media Converter |
Powered Device (PD) |
with Optical Interfaces |
|
|
100BASE-X (Fiber) Interface
PWR PoE
Fast Ethernet |
IP Camera |
AP |
|
LC-SC Fiber Cable Twisted-Pair Cable
Note: The PoE Media Converter supplies steady power and data connectivity to a powered device such as PoE IP Camera and PoE AP through an Ethernet cable.
Scenario 2: Connect Devices without Optical Interfaces
Ethernet Device |
Media Converter |
Media Converter |
Powered Device (PD) |
without Optical Interfaces |
|
|
10/100M
Fast Ethernet
PWR
PWR PoE
10/100M
Fast Ethernet
IP Camera |
AP |
Twisted-Pair Cable |
SC-SC Fiber Cable |
Twisted-Pair Cable |
Specifications
General Specifications
Standards |
IEEE 802.3, IEEE 802.3i, IEEE802.3u, IEEE802.3af |
LED |
PWR, Link/Act, PoE |
Connector |
1 SC fiber optic; 1 RJ45 jack |
|
10BASE-T: 2-pair UTP/STP of Cat. 3 or above (≤100 m) |
Twisted-Pair |
100BASE-TX: 2-pair UTP/STP of Cat. 5 or above (≤100 m) |
|
100BASE-BX10: SMF |
Fiber |
9/125 μm single-mode fiber |
Transmission Distance |
≤20 km |
Wavelength |
1310 nm TX, 1550 nm RX |
PoE |
802.3af; up to 15.4 W for the PoE port |
Power |
External Power Adapter: 48 V/0.5 A |
Dimensions |
94.5*73*27 mm |
EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
Environmental and Physical Specifications
Operating Temperature |
0˚C to 50˚C (32˚F to 122˚F) |
Storage Temperature |
-40˚C to 70˚C (-40˚F to 158˚F) |
Operating Humidity |
10% to 90% RH non-condensing |
Storage Humidity |
5% to 90% RH non-condensing |
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.
If you have any suggestions or needs on the product guides, welcome to email techwriter@tp-link.com.cn.
Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Do not point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight
Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact us.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.