Page 1
User Guide
AC1200 Wireless MU-MIMO VDSL/ADSL Modem Router
Archer VR400
REV3.0.0 1910012826
Page 2
Contents
About This Guide .........................................................................................................1
Chapter 1. Get to Know Your Modem Router. . . . . . . . . . . . . . . . . . . . . . . . . .3
1. 1. Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1. 2. Physical Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1. 2. 1. LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1. 2. 2. Ports and Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 2. Connect the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2. 1. Position Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2. 2. Connect Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 3. Log In to Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 4. Set Up Internet Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4. 1. Use Quick Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4. 2. Manually Set Up an Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4. 3. Test Internet Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4. 4. Set Up an IPv6 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4. 5. More Operation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. 5. 1. Wireless Router Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. 5. 2. 3G/4G Router Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Chapter 5. TP-Link Cloud Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5. 1. Register a TP-Link ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5. 2. Change Your TP-Link ID Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5. 3. Manage the User TP-Link IDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5. 3. 1. Add an TP-Link ID to Manage the Router . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5. 3. 2. Remove TP-Link ID(s) From Managing the Router . . . . . . . . . . . . . . . . . . 22
5. 4. Manage the Router via TP-Link Tether App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Chapter 6. OneMeshTM with Seamless Roaming. . . . . . . . . . . . . . . . . . . . . 24
6. 1. Set Up a OneMeshTM Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
TM
6. 2. Manage Devices in the OneMesh
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Chapter 7. IPTV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Page 3
Chapter 8. Guest Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8. 1. Create a Network for Guests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8. 2. Customize Guest Network Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Chapter 9. 3G/4G Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9. 1. As a Backup Solution for Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9. 2. As the Only Way to Access the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Chapter 10. Parental Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Chapter 11. QoS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
11. 1. Prioritize Internet Traffic with QoS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
11. 2. Update the Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Chapter 12. Network Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
12. 1. Firewall & DoS Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
12. 2. Service Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
12. 3. Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
12. 4. IP & MAC Binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
12. 5. IPv6 Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Chapter 13. NAT Forwarding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13. 1. Speed Up Internet Connections through NAT Boost . . . . . . . . . . . . . . . . . . . . . . . . . 55
13. 2. Translate Address and Port by ALG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
13. 3. Share Local Resources over the Internet by Virtual Server. . . . . . . . . . . . . . . . . . . 56
13. 4. Open Ports Dynamically by Port Triggering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
13. 5. Make Applications Free from Port Restriction by DMZ . . . . . . . . . . . . . . . . . . . . . . . 59
13. 6. Make Xbox Online Games Run Smoothly by UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Chapter 14. VPN Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
14. 1. Use OpenVPN to Access Your Home Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
14. 2. Use PPTP VPN to Access Your Home Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
14. 3. Use IPSec VPN to Access Your Home Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Chapter 15. Specify Your Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . 72
15. 1. LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
15. 1. 1. Change the LAN IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
15. 1. 2. Use the Modem Router as a DHCP Server. . . . . . . . . . . . . . . . . . . . . . . . . 74
15. 1. 3. Reserve LAN IP Addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Page 4
15. 2. IPv6 LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
15. 2. 1. Configure the RADVD Address Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
15. 2. 2. Configure the DHCPv6 Server Address Type . . . . . . . . . . . . . . . . . . . . . . 76
15. 3. Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
15. 3. 1. Specify Basic Wireless Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
15. 3. 2. Use WPS for Wireless Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
15. 3. 3. Schedule Your Wireless Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
15. 3. 4. View Wireless Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
15. 3. 5. Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
15. 4. Set Up a Dynamic DNS Service Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
15. 5. Create Static Routes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
15. 6. Set Up the IPv6 Tunnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
15. 6. 1. Use the Public IPv6 Tunnel Service-6to4 . . . . . . . . . . . . . . . . . . . . . . . . . . 88
15. 6. 2. Specify the 6rd Tunnel with Parameters Provided by Your ISP . . . . . . 89
Chapter 16. Administrate Your Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
16. 1. Set System Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
16. 2. Update the Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
16. 2. 1. Online Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
16. 2. 2. Local Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
16. 3. Back up and Restore Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
16. 4. Reboot the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
16. 5. Change the Administrator Account. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
16. 6. Local Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
16. 7. Remote Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
16. 8. System Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
16. 9. Monitor the Internet Traffic Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
16. 10. CWMP Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
16. 11. SNMP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Appendix: Troubleshooting ............................................................................... 104
Page 5
About This Guide
This guide is a complement to Quick Installation Guide. The Quick Installation Guide
provides instructions for quick internet setup, while this guide contains details of each
function and demonstrates how to configure them in typical scenarios.
Features available in the modem router may vary by model and software version. Modem
router availability may also vary by region or ISP. All images, steps, and descriptions in
this guide are only examples and may not reflect your actual modem router experience.
Conventions
In this guide, the following conventions are used:
Convention
Underline
Teal
>
Note:
Tips:
Symbols on
the web page
Description
Hyperlinks are in teal and underlined. You can click to redirect to a website
or a specific section.
Key information appears in teal, including management page text such as
menus, items, buttons and so on.
The menu structures to show the path to load the corresponding page. For
example, Advanced > Wireless > MAC Filtering
function page is under the Wireless menu that is located in the Advanced
tab.
Ignoring this type of note might result in a malfunction or damage to the
device.
Indicates important information that helps you make better use of your
device.
click to edit the corresponding entry.
•
•
click to delete the corresponding entry.
•
click to enable or disable the corresponding entry.
•
click to view more information about items on the page.
Speed/Coverage Disclaimer
means the MAC Filtering
Maximum wireless signal rates are the physical rates derived from IEEE Standard 802.11
specifications. Range, coverage, and maximum quantity of connected devices are
based on test results under normal usage conditions. Actual wireless data throughput,
wireless coverage, and quantity of connected devices are not guaranteed and will vary
as a result of 1) environmental factors, including building materials, physical objects,
and obstacles, 2) network conditions, including local interference, volume and density
of traffic, product location, network complexity, and network overhead, and 3) client
limitations, including rated performance, location, connection quality, and client
condition.
*Use of MU-MIMO requires clients to also support MU-MIMO.
1
Page 6
More Info
• The latest firmware and management app are available from the Download Center at
https://www.tp-link.com/support/download/.
• The Quick Installation Guide (QIG) can be found where you find this guide or inside the
product packaging.
• Specifications can be found on the product page at https://www.tp-link.com.
• TP-Link Community is provided for you to share knowledge and discuss our products
at https://community.tp-link.com.
• Our Technical Support contact information can be found at the Contact Technical
Support page at https://www.tp-link.com/support.
2
Page 7
Chapter 1
Get to Know Your Modem Router
This chapter introduces the modem router by detailing its main features and appearance.
It contains the following sections:
• Product Overview
• Physical Appearance
Page 8
Chapter 1
1. 1. Product Overview
TP-Link’s modem router is a combined wired/wireless network connection device with
wireless router and DSL modem capabilities.
With DSL and LAN/WAN ports, the modem router is compatible with DSL connections
and fiber/cable access.
Ethernet ports and adjustable antennas enable the modem router to provide wired and
wireless access for multiple computers and mobile devices.
With an array of additional features, the modem router is the perfect hub for your home
or business network.
1. 2. Physical Appearance
1. 2. 1. LED
The modem router’s LEDs are located on the front panel. You can check the modem
router’s working status by following the LED Explanation table.
4
Page 9
Chapter 1
LED Explanation
Name Status
On The system has started up successfully.
Power
DSL
Internet
WiFi
LAN
Flashing
Off
On DSL synchronization is complete.
Flashing DSL synchronization is in progress.
Off
On Internet service is available.
Off
On The wireless 2.4GHz/5GHz band is working properly.
Off The wireless 2.4GHz/5GHz band is disabled.
On
Off No LAN port is connected to a powered-on device.
Indication
The system is starting up or firmware is being upgraded.
Do not disconnect or power off your modem router.
Power is off. Please ensure that the power adapter is
connected correctly.
DSL synchronization failed. Please refer to 1 for
troubleshooting.
Internet connection is incorrect or the modem router
is operating in Bridge mode. Please refer to 2 for
troubleshooting.
At least one LAN port is connected to a powered-on
device.
On The USB device is ready to use.
USB
Flashing The USB device is being identified.
Off No USB device is plugged into the USB port.
Note:
1. If the DSL LED is off, please check your internet connection. Refer to Connect Your Modem Router for more
information about how to connect to the internet correctly. If you have already made a successful connection, please
contact your ISP to make sure your internet service is available now.
2. If the Internet LED is off, please check your DSL LED first. If your DSL LED is also off, please refer to 1. If your DSL LED
is ON, reconnect your modem router correctly by referring to related guide.
3. Turn on or off the LEDs by pressing the LED On/Off button on the top panel.
5
Page 10
Chapter 1
1. 2. 2. Ports and Antennas
The modem router’s back panel shows the connection ports, buttons and antennas.
Refer to the following for detailed instructions.
Item
Power Port
WiFi Button Press to turn Wi-Fi on or off.
WPS/Reset Button
USB Port For connecting to USB modems.
LAN1, LAN2, LAN3,
and LAN4/WAN
Ports
DSL Port
Antennas Used for wireless operation and data transmission.
For connecting the modem router to power socket via the provided
power adapter.
Press for 1 second to start a WPS synchronization.
Press and hold for at least 5 seconds until all LEDs turn on momentarily
to reset the modem router to factory default settings
For connecting to your PCs or other Ethernet network devices.
In wireless router mode, the LAN4/WAN port is used for connecting to
a Cable/FTTH/VDSL/ADSL device.
For connecting the modem router to the Internet. Connect the port to
the splitter or directly connect the port to the phone jack via a phone
cable. For details, please refer to Connect Your Modem Router.
Description
.
6
Page 11
Chapter 2
Connect the Hardware
This chapter contains the following sections:
• Position Your Modem Router
• Connect Your Modem Router
Page 12
Chapter 2
H
DØ
Ød
NOTE:
6≤D≤10mm
3≤d≤4mm
H≤3mm
SECTION
X-X
A
A(3/1)
161.85
14
Ø10
Ø4.3
1.9
4.9
X
X
2. 1. Position Your Modem Router
With the modem router, you can access your network from anywhere within the
wireless network coverage. However, the wireless signal strength and coverage varies
depending on the environment your modem router is in. Obstacles may limit the range
of the wireless signal, for example, concrete structures, thick walls.
For best Wi-Fi performance, and to keep your network secure:
• Do not locate the modem router in a place where it will be exposed to moisture or
excessive heat.
• Keep the product away from strong electromagnetic radiation and devices that emit
electromagnetic waves.
• Place the modem router in a location where it can be connected to the various devices
as well as to a power source.
• Make sure the cables and power cord are safely placed out of the way so they do not
create a tripping hazard.
Generally, the router is placed on a horizontal surface, such as on a shelf or desktop.
The device also can be mounted on the wall as shown in the following figure.
Note:
The diameter of the screw, 6mm<D<10mm, and the distance of two screws is 161.85mm. The screw that project from
the wall need around 4mm based, and the length of the screw need to be at least 20mm to withstand the weight of the
product.
2. 2. Connect Your Modem Router
Follow the steps below to connect your modem router.
1. Connect the DSL line and power adapter. The electrical outlet shall be installed
near the device and shall be easily accessible.
8
Page 13
Chapter 2
Phone Jack
Phone Cable
Power Adapter
1
Verify that the following LEDs turn
LINE
PHONE
MODEM
Phone (Optional)
USB LAN1 LAN2 LAN3
DSL Splitter
Phone Cable
If you don’t need the phone service, just directly connect the modem router to the phone jack
with the provided phone cable, then follow steps 3 and 4 to complete the hardware connection.
WPS�Reset
Modem Router
3
LAN4�WAN
2
4
stable before continuing with the
conguration.
Power On DSL On
Note: The DSL LED takes about 1 to 2
minutes to stabilize.
Wi-Fi On
2. Connect your computer to the modem router.
Method 1: Wired
Connect your computer’s Ethernet port to the LAN port on the modem router via the
Ethernet cable.
Method 2: Wirelessly
Use the default SSID (Wireless Network Name) and Wireless Password printed on the
product label of the modem router to connect wirelessly.
Method 3: Use the WPS button
Wireless devices that support WPS, including Android phones, tablets, most USB
network cards, can be connected to your router through this method. (WPS is not
supported by iOS devices.)
Note:
The WPS function cannot be configured if the wireless function of the router is disabled. Also, the WPS function will be
disabled if your wireless encryption is WEP. Please make sure the wireless function is enabled and is configured with the
appropriate encryption before configuring the WPS.
1 ) Tap the WPS icon on the device’s screen.
2 ) Immediately press the WPS button on your modem router.
3 ) The WPS LED flashes for about two minutes during the WPS process.
4 ) When the WPS LED stabilizes and remains on, the client device has successfully
connected to the modem router.
9
Page 14
Chapter 2
10
Page 15
Chapter 3
Log In to Your Modem Router
Page 16
Chapter 3
Log In to Your Modem Router
With the web management page, it is easy to configure and manage the modem router.
The web management page can be used on any Windows, Macintosh or UNIX OS with a
Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
Follow the steps below to log in to your modem router.
1. If the TCP/IP Protocol on your computer is set to the static (fixed) IP address, you
need to change its settings to obtain an IP address automatically. Refer to Appendix:
Troubleshooting to configure your computer.
2. Launch a web browser and go to http://tplinkmodem.net or http://192.168.1.1.
Create a strong password and click Let’s Get Started to log in.
Note:
If you have registered a TP-Link ID and bind your cloud router to it, the login password you created here should be
ineffective. Please log in to the cloud router using your TP-Link ID.
12
Page 17
Chapter 4
Set Up Internet Connections
This chapter introduces how to connect your modem router to the internet. The
modem router is equipped with a web-based Quick Setup wizard. It has many ISP
information built in, automates many of the steps and verifies that those steps have
been successfully completed. Furthermore, you can also set up an IPv6 connection if
your ISP provides IPv6 service.
This chapter includes the following sections:
• Use Quick Setup Wizard
• Manually Set Up an Internet Connection
• Test Internet Connectivity
• Set Up an IPv6 Connection
• More Operation Modes
Page 18
Chapter 4
Set Up Internet Connections
4. 1. Use Quick Setup Wizard
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password your
set for the router.
2. Click Quick Setup on the top of the page. Then follow the step-by-step instructions
to connect your router to the internet.
3. To enjoy a more complete service from TP-Link (remote management, TP-Link
DDNS, etc.), log in with your TP-Link ID or click Register Now to get one. Then follow
the instructions to bind the modem router to your TP-Link ID.
Note:
1. To learn more about the TP-Link Cloud service, please refer to the TP-Link Cloud section.
2. If you do not want to register a TP-Link ID for now, you may click Log In Later to proceed.
3. If you have changed the preset wireless network name (SSID) and wireless password during the Quick Setup process,
all your wireless devices must use the new SSID and password to connect to the router.
4. 2. Manually Set Up an Internet Connection
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password your
set for the router.
2. Go to Basic > Internet page. Select your ISP, and related information will be
automatically filled in. For some ISPs, you may need to manually specify some
information provided. If you can’t find your ISP in the ISP List, select Other and then
enter the information provided by your ISP.
14
Page 19
Chapter 4
Set Up Internet Connections
3. Click Save to make the settings effective, and you can refer to Test Internet
Connectivity to test the internet connection.
Tips: You can view and edit all internet connection settings on the Advanced > Network > Internet page.
4. 3. Test Internet Connectivity
After manually setting up the internet connection, you need to test the internet
connectivity. The modem router provides a diagnostic tool to help you locate the source
of any problems.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password your
set for the router.
2. Go to Advanced > System Tools > Diagnostics page.
15
Page 20
Chapter 4
Set Up Internet Connections
3. Click Start to test the internet connectivity and you will see the test result in the
gray box.
4. 4. Set Up an IPv6 Connection
If your ISP has provided a DSL line that supports IPv6 connection as well as some
detailed IPv6 parameters, you can manually set up an IPv6 connection.
If your ISP provides an IPv4-only connection or IPv6 tunnel service, permit IPv6
connection by referring to Set Up the IPv6 Tunnel.
Follow the steps below to set up an IPv6 connection:
1. Make sure you have set up an IPv4 connection either manually or by using the Quick
Setup wizard before setting up an IPv6 connection.
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password your
set for the router.
3. Go to Advanced > Network > Internet page.
4. Select your WAN Interface Name (Status should be Connected) and click the
(Edit) icon.
16
Page 21
Chapter 4
Set Up Internet Connections
5. Scroll down the page, enable IPv6, and configure the IPv6 parameters.
• Addressing Type: Consult your ISP for the addressing type (DHCPv6 or SLAAC).
SLAAC is the most commonly used addressing type.
• IPv6 Gateway: Keep the default setting as Current Connection.
Note: If your ISP has provided the IPv6 address, click Advanced to reveal more settings. Check to use IPv6
specified by ISP and enter the parameters provided by your ISP.
6. Click OK to make the settings effective. Now IPv6 service is available for your
network.
4. 5. More Operation Modes
The modem router supports two more operation modes: Wireless Router mode and
3G/4G Router mode. You can change the mode according to your needs.
4. 5. 1. Wireless Router Mode
If you already have a modem or your internet comes via an Ethernet jack on the wall, you
can set up the modem router as a regular wireless router to share the internet.
1. Find the WAN port (labeled as LAN4/WAN) on the modem router, and connect it
to your existing modem or the Ethernet jack on the wall. Then connect the power
adapter and turn on the modem router. If you connect an existing modem, reboot it
to get the modem router connected to the internet.
2. Connect your computer to the modem router. For details, refer to Connect Your
Modem Router.
3. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password your
set for the router.
4. Go to Advanced > Operation Mode, select the Wireless Router Mode, and click
Save. The modem router will reboot.
17
Page 22
Chapter 4
Set Up Internet Connections
5. Go to Basic > Internet, select the Connection Type, and enter the information
provided by your ISP.
6. Click Save to make the settings effective.
Tips:
1. You can view and edit all internet connections on Advanced > Network > Internet page.
2. In the Wireless Router Mode, you can also permit IPv6 connection by setting up an IPv6 connection or the IPv6 tunnel
just as in the DSL Modem Router Mode. For details, refer to Set Up an IPv6 Connection and Set Up the IPv6 Tunnel.
4. 5. 2. 3G/4G Router Mode
The modem router can be used as a 3G/4G wireless router if you have a 3G/4G USB
modem. There are two ways to use your 3G/4G network:
• As a backup solution for internet access
Use this way if you have set up an internet connection successfully and want to use the
3G/4G network as a backup network. Your modem router will be directly connected to
the 3G/4G network when the original network service fails. For detailed instructions,
refer to As a Backup Solution for Internet Access.
• As the only way to access the internet
Use this way if wired internet access is not available and you can only use the 3G/4G
network to access the internet. For detailed instructions, refer to As the Only Way to
Access the Internet.
Tips:
In the 3G/4G Router Mode, you can also permit IPv6 connection by setting up the IPv6 tunnel just as in the DSL Modem
Router Mode. For details, refer to Set Up the IPv6 Tunnel.
18
Page 23
Chapter 5
TP-Link Cloud Service
TP-Link Cloud service provides a better way to manage your cloud devices. Log in to
your router with a TP-Link ID, and you can easily monitor and manage your home network
when you are out and about via the Tether app on your smartphone or tablet. To ensure
that your router stays new and gets better over time, the TP-Link Cloud will notify you
when an important firmware upgrade is available. Surely you can also manage multiple
TP-Link Cloud devices with a single TP-Link ID.
This chapter introduces how to register a new TP-Link ID, bind or unbind TP-Link IDs
to manage your router, and the Tether app with which you can manage your home
network no matter where you may find yourself.
It contains the following sections:
• Register a TP-Link ID
• Change Your TP-Link ID Information
• Manage the User TP-Link IDs
• Manage the Router via TP-Link Tether App
Page 24
Chapter 5
TP-Link Cloud Service
5. 1. Register a TP-Link ID
If you have skipped the registration during the Quick Setup process, you can:
1. Visit http://tplinkmodem.net, and log in with the password you set for the router.
2. Go to Basic > TP-Link Cloud.
3. Click Register Now and follow the instructions to register a TP-Link ID.
4. After activating your TP-Link ID, come back to the TP-Link Cloud page to log in. The
first-time login TP-Link ID will be bound automatically to your cloud router as an
Admin.
Note:
• To learn more about the Admin and User TP-Link ID, refer to Manage the User TP-Link IDs.
• Once the router is bound to your TP-Link ID, you need to log in to the router with the TP-Link ID.
• You can register another TP-Link ID via the Tether APP. Please refer to Manage the Router via TP-Link Tether App to
install the app and register a new one
• If you want to unbind the admin TP-Link ID from your router, please go to Basic > TP-Link Cloud, click Unbind in the
Device Information section.
5. 2. Change Your TP-Link ID Information
Follow the steps below to change your email address and password of you TP-Link ID
as needed.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID.
2. Go to Basic > TP-Link Cloud, and focus on the Account Information section.
• Change your email address
1. Click
behind the Email.
2. Enter the password of your TP-Link ID, then the new email address. And click Save.
20
Page 25
Chapter 5
• Change your password
TP-Link Cloud Service
1. Click
2. Enter the current password, then a new password twice. And click Save.
behind the Password.
5. 3. Manage the User TP-Link IDs
The first-time login TP-Link ID will be bound automatically to your router as an Admin
account. An admin account can add or remove other TP-Link IDs to the same router
as Users. Admin account and User accounts both can monitor and manage the router
locally or remotely, except that user accounts cannot:
• Reset the router to its factory default settings from the web management page or the
Tether app.
21
Page 26
Chapter 5
TP-Link Cloud Service
• Add/remove other TP-Link IDs to/from the router.
5. 3. 1. Add an TP-Link ID to Manage the Router
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID.
2. Go to Basic > TP-Link Cloud, and focus on the Bound Accounts section.
3. Click
Note:
If you need another TP-Link ID, please refer to Manage the Router via TP-Link Tether App to install the app and register
a new one.
, enter another TP-Link ID as needed and click Save.
4. The new TP-Link ID will be displayed in the Bound Accounts table as a User.
5. 3. 2. Remove TP-Link ID(s) From Managing the Router
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID.
2. Go to Basic > TP-Link Cloud, and focus on the Bound Accounts section.
3. Check the box(es) of the TP-Link ID(s) you want to remove and click Unbind.
22
Page 27
Chapter 5
TP-Link Cloud Service
5. 4. Manage the Router via TP-Link Tether App
The Tether app runs on iOS and Android devices like smartphones and tablets.
1. Open the Apple App Store or Google Play and search the key word TP-Link Tether or
simply scan the QR code to download and install the app.
OR
2. Launch the Tether app and log in with your TP-Link ID.
Note: If you don’t have an account, create one first.
3. Connect your device to the router’s wireless network.
4. Go back to the Tether app and select the model of your router.
5. Manage your router as needed.
23
Page 28
Chapter 6
TM
OneMesh
with Seamless
Roaming
This chapter introduces the TP-Link OneMeshTM feature.
It contains the following sections:
• Set Up a OneMesh
• Manage Devices in the OneMesh
TM
Network
TM
Network
Page 29
Chapter 6
OneMeshTM with Seamless Roaming
TP-Link OneMeshTM router and TP-Link OneMeshTM extenders work together to
form one unified Wi-Fi network. Walk through your home and stay connected with the
fastest possible speeds thanks to OneMesh’s seamless coverage.
Unified Wi-Fi Network
Router and extenders share the same wireless settings, including network name,
password, access control settings and more.
Seamless Roaming
Devices automatically switch between your router and extenders as you move
through your home for the fastest possible speeds.
Easy Setup and Management
Set up a OneMeshTM network with a push of WPS buttons. Manage all network devices
on the Tether app or at your router’s web management page.
Unified OneMeshTM Network
IN TER NE T
SAME
Network Name & Password
for Seamless Roaming
6. 1. Set Up a OneMeshTM Network
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. Go to Basic > OneMesh or Advanced > Wireless > OneMesh.
25
Page 30
Chapter 6
Note:
Early firmware versions may not support OneMeshTM. If you can’t find the OneMesh page, please upgrade your router
to the latest firmware version. For upgrade instructions, refer to Upgrade the Firmware.
OneMeshTM with Seamless Roaming
3. Connect one or more OneMeshTM extenders to this router by following the setup
instructions in the extenders’ manuals.
Note:
To check full list of TP-Link OneMeshTM devices, visit https://www.tp-link.com/onemesh/compatibility.
4. If you have set up an extender to join the OneMeshTM network, it will be listed in the
Devices in OneMesh Network list. Otherwise, you need to find it in the Available
TM
OneMesh Devices list and click Add to add it to the OneMesh
network.
Now your router and extenders successfully form one OneMeshTM network!
6. 2. Manage Devices in the OneMeshTM Network
In a OneMeshTM network, you can manage all mesh devices and clients on your router’s
web page.
26
Page 31
Chapter 6
OneMeshTM with Seamless Roaming
• To view all mesh devices and clients in the OneMeshTM network:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. Go to Basic > Network Map.
3. Click the Mesh Devices, Wired Clients, or Wireless Clients icon to view the related
device or client list.
• To manage each OneMeshTM device in the network:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. Go to Basic > OneMesh or Advanced > Wireless > OneMesh.
3. Click a OneMesh
TM
device to view the device information, or click <number> Clients
to view the clients connected to this device.
On the Device Info page, you can:
27
Page 32
Chapter 6
OneMeshTM with Seamless Roaming
• Click Manage Device to redirect to the web mangement page of this OneMesh
device.
• Click Leave OneMesh to delete this device from the OneMesh
TM
network.
TM
28
Page 33
Chapter 7
IPTV
IPTV is the abbreviation of Internet Protocol Television. The service can only be delivered
through the Internet, and our modem router provides a specific LAN port for IPTV.
By automatically separating IPTV from Internet surfing, you can enjoy a high quality of
video streaming and fast browsing speeds at the same time.
Page 34
Chapter 7
I want to:
Configure the modem router to enable Internet Protocol Television (IPTV) Services.
For example, I already bought IPTV service, but this service can only be delivered
through the Internet. Therefore, I need to configure my modem router first.
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > IPTV to open the configuration page.
3. Click Enable IPTV to enable this function.
4. Select your DSL modulation type.
5. If you select VDSL modulation type, check to enable VLAN and set the VLAN ID. If
you select ADSL, fill in PVC parameters (VPI and VCI). VLAN ID and PVC parameters
are all provided by your IPTV service provider.
6. Specify a LAN port for IPTV connection and connect the set-top box to this port.
7. Click Save to make the settings effective.
Done!
Modem router configuration is complete! You may still need to configure settings on
your set-top box before enjoying your IPTV service.
30
Page 35
Chapter 8
Guest Network
This function allows you to provide Wi-Fi access for guests without disclosing your
main network. When you have guests in your house, apartment, or workplace, you can
create a guest network for them. In addition, you can assign network authorities and
bandwidth for guests to ensure network security, privacy, and fluency.
• Create a Network for Guests
• Customize Guest Network Options
Page 36
Chapter 8
Guest Network
8. 1. Create a Network for Guests
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Guest Network. Locate the Wireless Settings section.
3. Create 2.4GHz and 5GHz guest network according to your needs.
1 ) Enable 2.4GHz Wireless or 5GHz Wireless or enable both according to your
needs.
2 ) Set an easy-to-identify SSID. Don‘t select Hide SSID unless you want your
guests and other people to manually input this SSID for Wi-Fi access.
3 ) Set Security to WPA/WPA2 Personal, keep the default Version and Encryption
values, and set an easy-to-remember password. 2.4GHz and 5GHz guest
networks share the same password.
4. Click Save. Now your guests can access your guest network using the SSID and
password you set!
Tips:
To view guest network information, go to Advanced > Status and find the Guest Network section.
8. 2. Customize Guest Network Options
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Guest Network.
32
Page 37
Chapter 8
Guest Network
3. Assign network authorities and bandwidth according to your needs.
• Allow Guests to Access Each Other
Select this check box to allow the clients in your guest network to access each
other’s files.
• Allow Guests to Access My Local Network
Select this check box to allow the clients in your guest network to access your local
network, not just the internet.
• Enable QoS for Guest Network
Select this check box to set the QoS Priority of the guest network. This option is
available only when QoS is enabled on the Advanced > QoS page.
4. Click Save. Now users in your guest network can enjoy only the network authorities
at the priority you assigned!
Tips:
To view guest network information, go to Advanced > Status and find the Guest Network section.
33
Page 38
Chapter 9
3G/4G Settings
This chapter describes how to set up 3G/4G network for your modem router.
• As a Backup Solution for Internet Access
• As the Only Way to Access the Internet
Page 39
Chapter 9
3G/4G Settings
The modem router can be used as a 3G/4G wireless router if you have a 3G/4G USB
modem. There are two ways to use your 3G/4G network:
• As a backup solution for internet access
• As the only way to access the internet
9. 1. As a Backup Solution for Internet Access
Using 3G/4G network as a backup solution for internet access, your modem router will
be directly connected to the 3G/4G network when the original network service fails.
Follow the steps below to set your 3G/4G network as a backup for internet access:
1. Plug your USB modem into the USB port of your modem router.
2. Visit http://tplinkmodem.net, then log in with your TP-Link ID or the password you
set for the modem router.
3. Go to Advanced > USB Settings > 3G/4G Settings, and select the box of Enable
3G/4G as a backup solution for Internet access.
4. Verify that your 3G/4G USB Modem is successfully identified.
Note: The 3G/4G USB modem will not be identified if it is incompatible with the modem router. Find the 3G/4G
Compatibility List on the web page: http://www.tp-link.com/en/comp-list.html. If your USB modem is incompatible,
contact our technical support.
35
Page 40
Chapter 9
5. Verify that the modem router has correctly recognized your Mobile ISP. When your
6. Click Advanced to have more configurations if needed.
7. Click Save to make the settings effective.
Mobile ISP is correct, you have successfully set 3G/4G network as a backup solution
for internet access. Otherwise, select the box Set the Dial Number, APN, Username
and Password manually and enter the information provided by your 3G/4G network
service provider.
3G/4G Settings
9. 2. As the Only Way to Access the Internet
If you want the 3G/4G network to be your only way to access the internet, follow the
steps below to configure:
1. Plug your USB modem into the USB port of your modem router.
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the modem router.
3. Go to Advanced > Operation Mode and choose 3G/4G Router Mode.
4. Click Save and when the modem router is successfully rebooted, the settings will
be effective.
5. Go to Advanced > USB Sharing > 3G/4G Settings.
6. Verify that your 3G/4G USB Modem is successfully detected.
36
Page 41
Chapter 9
Note: If your 3G/4G USB modem is incompatible with the modem router, it will not be identified. Find the 3G/4G
Compatibility List on the web page: http://www.tp-link.com/en/comp-list.html. If your USB modem is incompatible,
contact our technical support.
3G/4G Settings
7. Verify that the modem router has correctly recognized your Mobile ISP. When your
Mobile ISP is correct, you can enjoy the internet! Otherwise, select the box Set the
Dial Number, APN, Username and Password manually and enter the information
provided by your 3G/4G network service provider.
8. Select the Connection Mode. The default mode is Always on. You can choose
Connect on demand or Connect manually.
• If you choose Connect manually, you need to click the Connect or Disconnect
button to manually turn on or off the internet.
• If you choose Connect on demand, the network will automatically turn off when
there is no internet request in Max Idle Time, and turn on again when you try to
connect to the internet.
9. Click Advanced to have more configurations if needed.
10. Click Save to make the settings effective.
37
Page 42
Chapter 10
Parental Controls
This function allows you to block inappropriate, explicit and malicious websites and
limit internet access during specified time periods.
Page 43
Chapter 10
Parental Controls
I want to:
Control what types of websites my children or other home network users can visit and
the time of day they are allowed to access the internet.
For example, I want to allow my children’s devices (for example, a computer or a tablet)
to access only www.tp-link.com and wikipedia.org from 18:00 (6PM) to 22:00 (10PM) on
weekdays and not other time.
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Basic or Advanced > Parental Controls and enable Parental Controls.
3. Click Add.
39
Page 44
Chapter 10
Parental Controls
4. Click Scan, and add the device to be controlled. Or, enter the Device Name and
MAC Address manually.
5. Click the
icon to set the Effective Time. Drag the cursor over the appropriate
cell(s) and click OK.
Note: The time of Parental Controls is based on the system time of the modem router. Please go to Advanced > System
Tools > Time Settings to set the correct time..
6. Enter a Description for the entry.
7. Select the check box to enable this entry and click OK.
8. Enable Content Restriction and select the restriction mode.
40
Page 45
Chapter 10
Parental Controls
1 ) In Blacklist mode, the controlled devices cannot access any websites containing
the specified keywords during the Effective Time period.
2 ) In Whitelist mode, the controlled devices can only access websites containing
the specified keywords during the Effective Time period.
9. Click Add a New Keyword. You can add many keywords for both Blacklist and
Whitelist. Below are some sample entries to allow access.
1 ) Enter a web address (for example, www.tp-link.com) or a web address keyword
(for example, wikipedia) to only allow or block access to the websites containing
that keyword.
2 ) Specify the domain suffix (for example, .edu or .org) to allow access only to the
websites with that suffix.
10. Enter the keywords or websites you want to add and click Save.
Done!
Now you can control your children’s internet access according to your needs.
41
Page 46
Chapter 11
QoS
This chapter explains how to create a QoS (Quality of Service) rule to prioritize your
online activities, which minimizes the impact caused by heavy internet traffic.
It contains the following sections:
• Prioritize Internet Traffic with QoS
• Update the Database
Page 47
Chapter 11
QoS
11. 1. Prioritize Internet Traffic with QoS
QoS (Quality of Service) is designed to ensure the efficient operation of the network
when network congestion is encountered.
I want to:
Specify priority levels for some devices or applications.
For example, I have several devices that are connected to my wireless network. I would
like to set an intermediate speed on the internet for my phone.
How can I do that?
1. Enable QoS and set bandwidth allocation.
1 ) Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password
you set for the router.
2 ) Go to Advanced > QoS > Settings.
3 ) Select Enable QoS.
Note:
1. Qos and NAT Boost cannot be enabled at the same time. To disable NAT Boost, go to Advanced > NAT
Forwarding > NAT Boost , unclick it and save your settings.
2. NAT Boost ensure that the router has the best throughput. When NAT Boost is enabled, QoS and Traffic Monitor
will be disabled automatically.
4 ) Choose your Line Type.
5 ) Input the maximum upload and download bandwidth provided by your internet
service provider. 1Mbps equals to 1000Kbps.
6 ) If you want to prioritize the IPTV traffic, select Enable, the IPTV Priority will be
high.
7 ) Click Advanced and drag the scroll bar to set the bandwidth priority percentage.
8 ) Click Save.
43
Page 48
Chapter 11
2. Add a middle priority QoS rule for the phone.
1 ) Click Add in the Middle Priority area.
QoS
2 ) Select By Device and click Scan, then choose the respective device from the
list.
3 ) Click Save.
44
Page 49
Chapter 11
QoS
3. Refer to the steps above to apply other QoS rules if any.
Note:
If you want to delete a QoS rule, click to remove the responding rule from the list.
Done!
Now QoS is implemented to prioritize internet traffic.
11. 2. Update the Database
This function can help to add or update the applications the router supports. If the
applications you need are not listed in the Application list, you can try to download
the new version and upgrade the database. New database versions are posted at
www.tp-link.com and can be downloaded for free.
1. Download the latest QoS database from our website (www.tp-link.com).
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
3. Go to Advanced > QoS > Database. Click Browse to select the database upgrade file,
and then click Upgrade. Wait until the upgrade is complete and do not operate the
router during the process.
45
Page 50
Chapter 12
Network Security
This chapter guides you on how to protect your home network from unauthorized users
by implementing these network security functions. You can block or allow specific client
devices to access your wireless network using MAC Filtering, or using Access Control
for wired and wireless networks, or you can prevent ARP spoofing and ARP attacks by
using IP & MAC Binding and you can protect your IPv6 network by preventing access
from the internet using IPv6 Firewall.
• Firewall & DoS Protection
• Service Filtering
• Access Control
• IP & MAC Binding
• IPv6 Firewall
Page 51
Chapter 12
Network Security
12. 1. Firewall & DoS Protection
The SPI (Stateful Packet Inspection) Firewall and DoS (Denial of Service) Protection
protect the router from cyber attacks.
The SPI Firewall can prevent cyber attacks and validate the traffic that is passing
through the router based on the protocol. This function is enabled by default, and it’s
recommended to keep the default settings.
DoS Protection can protect your home network against DoS attacks from flooding your
network with server requests. Follow the steps below to configure DoS Protection.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Security > Firewall & DoS Protection.
3. Enable DoS Protection.
4. Set the level (Low, Middle or High) of protection for ICMP-Flood Attack Filtering,
UDP-Flood Attack Filtering and TCP-Flood Attack Filtering.
• ICMP-Flood Attack Filtering - Enable to prevent the ICMP (Internet Control
Message Protocol) flood attack.
• UDP-Flood Attack Filtering - Enable to prevent the UDP (User Datagram
Protocol) flood attack.
• TCP-Flood Attack Filtering - Enable to prevent the TCP (Transmission Control
Protocol) flood attack.
5. Click Save.
Tips:
1. The level of protection is based on the number of traffic packets. Specify the level at DoS Protection Level
Settings.
47
Page 52
Chapter 12
2. The protection will be triggered immediately when the number of packets exceeds the preset threshold value,
and the vicious host will be displayed in the Blocked DoS Host List.
Network Security
12. 2. Service Filtering
With Service Filtering, you can prevent certain users from accessing the specified
service, and even block internet access completely.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Security > Service Filtering.
3. Toggle on Service Filtering.
4. Click Add.
48
Page 53
Chapter 12
Network Security
5. Select a Service Type from the drop-down list and the following four fields will be
auto-populated. Select Custom when your desired service type is not listed, and
enter the information manually.
6. Specify the IP address(es) that this filtering rule will apply to.
7. Click Save.
Note: If you want to disable this entry, click the icon.
12. 3. Access Control
Access Control is used to block or allow specific client devices to access your network
(via wired or wireless) based on a list of blocked devices (Blacklist) or a list of allowed
devices (Whitelist).
I want to:
Block or allow specific client devices to access my network (via wired or wireless).
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Security > Access Control and enable Access Control.
49
Page 54
Chapter 12
Network Security
3. Select the access mode to either block (recommended) or allow the device(s) in the
list.
To block specific device(s)
1 ) Select Blacklist and click Save.
2 ) Select the device(s) to be blocked in the Online Devices table.
3 ) Click Block above the Online Devices table. The selected devices will be added
to Devices in Blacklist automatically.
To allow specific device(s)
1 ) Select Whitelist and click Save.
2 ) Click Add.
50
Page 55
Chapter 12
1 ) Click San and the Device Name and MAC Address will be automatically filled in.
2 ) Click Save.
Or enter the Device Name and MAC Address manually.
Network Security
Done!
Now you can block or allow specific client devices to access your network (via wired or
wireless) using the Blacklist or Whitelist.
12. 4. IP & MAC Binding
IP & MAC Binding, namely, ARP (Address Resolution Protocol) Binding, is used to bind
a network device’s IP address to its MAC address. This will prevent ARP spoofing and
other ARP attacks by denying network access to a device with a matching IP address in
the Binding list, but an unrecognized MAC address.
I want to:
Prevent ARP spoofing and ARP attacks.
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Security > IP & MAC Binding and enable IP & MAC Binding.
3. Bind your device(s) according to your needs.
51
Page 56
Chapter 12
To bind the connected device(s)
1 ) Select the device(s) to be bound in the ARP List.
2 ) Click Bind to add to the Binding List.
To bind the unconnected device
1 ) Click Add.
Network Security
2 ) Enter the MAC Address and IP Address that you want to bind.
3 ) Select the check box to enable the entry and click OK.
Done!
Enjoy the internet without worrying about ARP spoofing and ARP attacks.
12. 5. IPv6 Firewall
IPv6 Firewall protects your IPv6 network by preventing access from the internet.
However, when you are hosting a service, such as a file sharing server in your local
network, you can choose to allow access to the server from the internet by adding
entries on this page. This feature is available only when you’ve set up an IPv6 connection.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Security > IPv6 Firewall.
3. Click Add.
52
Page 57
Chapter 12
Network Security
4. Select an interface name from the drop-down list. Interface names are names of
the internet connections you have set up.
5. Click Scan to select a service from the list to automatically populate the Port field
with an appropriate port number. It is recommended to keep the default Port if you
are unsure about which one to use. If the service is not listed, manually enter the
Service Type and the Port number (e.g., 21 or 21-25).
6. Click Scan to select the local host device running the service. If the device is not
listed, enter its global IPv6 address in the Global IPv6 Address field
7. Select a protocol for the service from the drop-down list.
8. Select Enable This Entry and click Save.
Note: If you want to disable this entry, click the icon.
53
Page 58
Chapter 13
NAT Forwarding
Modem router’s NAT (Network Address Translation) feature makes the devices in the
LAN use the same public IP address to communicate in the internet, which protects the
local network by hiding IP addresses of the devices. However, it also brings about the
problem that external host cannot initiatively communicate with the specified device in
the local network.
The modem router can use a forwarding feature to remove the isolation of NAT and
allow external internet hosts to intuitively communicate with the devices in the local
network, thus enabling some special features.
TP-Link modem router includes four forwarding rules. If two or more rules are set, the
priority of implementation from high to low is Virtual Servers, Port Triggering, UPNP and
DMZ. The modem router also has NAT Boost feature to ensure that the router has the
best throughput.
This chapter contains the following sections:
• Speed Up Internet Connections through NAT Boost
• Translate Address and Port by ALG
• Share Local Resources over the Internet by Virtual Server
• Open Ports Dynamically by Port Triggering
• Make Applications Free from Port Restriction by DMZ
• Make Xbox Online Games Run Smoothly by UPnP
Page 59
Chapter 13
NAT Forwarding
13. 1. Speed Up Internet Connections through NAT
Boost
NAT Boost is designed to speed up Internet connections. It ensures that the router has
the best throughput.
Note:
NAT Boost, QoS, and Traffic Monitor cannot be enabled simultaneously. When NAT Boost is enabled, QoS and Traffic
Monitor will be disabled automatically.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > NAT Forwarding > NAT Boost.
3. Enable NAT Boost and click Save.
13. 2. Translate Address and Port by ALG
ALG (Application Layer Gateway) allows customized NAT (Network Address Translation)
traversal filters to be plugged into the gateway to support address and port translation
for certain application layer “control/data” protocols: FTP, TFTP, H323 etc. Enabling ALG
is recommended.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > NAT Forwarding > ALG .
55
Page 60
Chapter 13
• PPTP Pass-through: If enabled, it allows Point-to-Point sessions to be tunneled
through an IP network and passed through the router.
• L2TP Pass-through: If enabled, it allows Layer 2 Point-to-Point sessions to be tunneled
through an IP network and passed through the router.
• IPSec Pass-through: If enabled, it allows IPSec (Internet Protocol Security) to
be tunneled through an IP network and passed through the router. IPSec uses
cryptographic security services to ensure private and secure communications over
IP networks.
• FTP ALG: If enabled, it allows FTP (File Transfer Protocol) clients and servers to transfer
data via NAT.
• TFTP ALG: If enabled, it allows TFTP (Trivial File Transfer Protocol) clients and servers
to transfer data via NAT.
• H323 ALG: If enabled, it allows Microsoft NetMeeting clients to communicate via NAT.
• SIP ALG: If enabled, it allows clients communicate with SIP (Session Initiation Protocol)
servers via NAT.
NAT Forwarding
• RTSP ALG: If enabled, it allows RTSP (Real-Time Stream Protocol) clients and servers
to transfer data via NAT.
13. 3. Share Local Resources over the Internet by
Virtual Server
When you build up a server in the local network and want to share it on the internet,
Virtual Server can realize the service and provide it to the internet users. At the same
time virtual server can keep the local network safe as other services are still invisible
from the internet.
Virtual server can be used for setting up public services in your local network, such as
HTTP, FTP, DNS, POP3/SMTP and Telnet. Different service uses different service port.
Port 80 is used in HTTP service, port 21 in FTP service, port 25 in SMTP service and port
110 in POP3 service. Please verify the service port number before the configuration.
I want to:
Share my personal website I’ve built in a local network with my friends through the
internet.
For example, the personal website has been built on my home PC (192.168.1.100). I
hope that my friends can visit my website. The PC is connected to the modem router
with the WAN IP address 218.18.232.154.
56
Page 61
Chapter 13
Modem Router
WAN: 218.18.232.154
LAN
Home
Personal Website
WPS�Reset
USB LAN1 LAN2 LAN3
LAN4�WAN
NAT Forwarding
How can I do that?
1. Assign a static IP address to your PC, for example 192.168.1.100.
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
3. Go to Advanced > NAT Forwarding > Virtual Servers, click Add.
4. Click Scan, and choose HTTP. The external port, internal port and protocol will be
automatically filled with contents. Enter the PC’s IP address 192.168.1.100 in the
Internal IP field.
5. Click Save to save the settings.
Tips:
1. It is recommended to keep the default settings of Internal Port and Protocol if you are not clear about which port and
protocol to use.
2. If the service you want to use is not in the Service Type, you can enter the corresponding parameters manually. You
should verify the port number that the service needs.
3. You can add multiple virtual server rules if you want to provide several services from a modem router. Please note that
the External Port cannot be overlapped.
57
Page 62
Chapter 13
NAT Forwarding
Done!
Internet users can enter http://WAN IP (in this example: http://218.18.232.154) to visit
your personal website.
Tips:
1. For a WAN IP that is assigned dynamically by ISP, it is recommended to apply and register a domain name for the
WAN by DDNS, go to Set Up a Dynamic DNS Service Account for more information. Then you can use http://domain
name to visit the website.
2. If you have changed the default External Port, you should use http://WAN IP: External Port or http://domain name:
External Port to visit the website.
13. 4. Open Ports Dynamically by Port Triggering
Port triggering can specify a triggering port and its corresponding external ports. When
a host in the local network initiates a connection to the triggering port, all the external
ports will be opened for subsequent connections. The modem router can record the IP
address of the host. When the data from the internet returns to the external ports, the
modem router can forward them to the corresponding host. Port triggering is mainly
applied to online games, VoIPs and video players. Common applications include MSN
Gaming Zone, Dialpad, Quick Time 4 players, and so on.
Follow the steps below to configure the port triggering rules:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > NAT Forwarding > Port Triggering and click Add.
58
Page 63
Chapter 13
NAT Forwarding
3. Click Scan, and select the desired application. The triggering port and protocol, the
external port and protocol will be automatically filled with contents. Here we take
MSN Gaming Zone as an example.
4. Click Save to save the settings.
Tips:
1. You can add multiple port triggering rules according to your network need.
2. If the application you need is not listed in the Existing Applications list, please enter the parameters manually. You
should verify the external ports the application uses first and enter them into External Port field according to the
format the page displays.
13. 5. Make Applications Free from Port Restriction
by DMZ
When a PC is set to be a DMZ (Demilitarized Zone) host in the local network, it is totally
exposed to the internet, which can realize the unlimited bidirectional communication
between internal hosts and external hosts. The DMZ host becomes a virtual server with
all ports opened. When you are not clear about which ports to open in some special
applications, like IP camera and database software, you can set the PC to be a DMZ
host.
Note:
DMZ is most applicable when you don’t know which ports to open. When it is enabled, the DMZ host is totally exposed
to the internet, which may bring some potential safety hazard. If DMZ is not in use, please disable it in time.
I want to:
Make the home PC join the internet online game without port restriction.
For example, Due to some port restriction, when playing the online games, you can
login normally but cannot join a team with other players. To solve this problem, set your
PC as a DMZ with all ports opened.
How can I do that?
1. Assign a static IP address to your PC, for example 192.168.1.100.
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
3. Go to Advanced > NAT Forwarding > DMZ and select the checkbox to enable DMZ.
59
Page 64
Chapter 13
NAT Forwarding
4. Enter the IP address 192.168.1.100 in the DMZ Host IP Address filed.
5. Click Save to save the settings.
Done!
The configuration is completed. You’ve set your PC to a DMZ host and now you can
make a team to game with other players.
13. 6. Make Xbox Online Games Run Smoothly by
UPnP
UPnP (Universal Plug and Play) protocol allows the applications or host devices
to automatically find the front-end NAT device and send request to it to open the
corresponding ports. With UPnP enabled, the applications or host devices in the
both sides of NAT device can freely communicate with each other realizing the
seamless connection of the network. You may need to enable the UPnP if you want
to use applications such as multiplayer gaming, peer-to-peer connections, real-time
communication (for example, VoIP or telephone conference), or remote assistance.
Tips:
1. UPnP is enabled by default in this modem router.
2. Only the application supporting UPnP protocol can use this feature.
3. UPnP feature needs the support of operating system (e.g. Windows Vista/ Windows 7/ Windows 8, etc. Some of
operating system need to install the UPnP components).
For example, when you connect your Xbox to the modem router which has connected to
the internet to play online games, UPnP will send request to the modem router to open
the corresponding ports allowing the following data penetrating the NAT to transmit.
Therefore, you can play Xbox online games without a hitch.
LAN
WPS�Reset
USB LAN1 LAN2 LAN3
WAN
LAN4�WAN
Modem RouterXbox
If necessary, you can follow the steps to change the status of UPnP.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router;
2. Go to Advanced > NAT Forwarding > UPnP and toggle on or off according to your
needs.
60
Page 65
Chapter 13
NAT Forwarding
61
Page 66
Chapter 14
VPN Server
The VPN (Virtual Private Networking) Server allows you to access your home network
in a secured way through the internet when you are out of the house. The router offers
three ways to setup VPN connection: OpenVPN, PPTP (Point to Point Tunneling Protocol)
VPN and IPSec (Internet Protocol Security) VPN.
OpenVPN is somewhat complex but with greater security and more stability. It is suitable
for restricted environment, such as campus network and company intranet.
PPTP VPN is easier to use and its speed is faster. It’s compatible with most operating
systems and also supports mobile devices. However, its security is poor and packets
may be cracked easily. PPTP VPN may be blocked by some ISPs.
IPSec (IP Security) is a set of services and protocols defined by IETF (Internet Engineering
Task Force) to provide high security for IP packets and prevent attacks.
This chapter contains the following sections, please choose the appropriate VPN server
connection type according to your needs.
• Use OpenVPN to Access Your Home Network
• Use PPTP VPN to Access Your Home Network
• Use IPSec VPN to Access Your Home Network
Page 67
Chapter 14
VPN Server
14. 1. Use OpenVPN to Access Your Home Network
In an OpenVPN connection, the home network can act as a server, and the remote
device can access the server through the router which acts as an OpenVPN Server
gateway. To use the VPN feature, you should enable OpenVPN Server on your router,
install and run VPN client software on the remote device. Please follow the steps below
to set up an OpenVPN connection.
USB LAN1 LAN2 LAN3
WPS�Reset
LAN4�WAN
Home Network Remote DeviceRouter
Step 1. Set up OpenVPN Server on Your Router
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. Go to Advanced > VPN > OpenVPN, and select Enable VPN Server.
Note:
• Before you enable VPN Server, we recommend you configure Dynamic DNS Service (recommended) or
assign a static IP address for your router’s WAN port and synchronize your System Time via the internet.
• The first time you configure the OpenVPN Server, you may need to Generate a certificate before you
enable the VPN Server.
3. Select the Service Type (communication protocol) for OpenVPN Server: UDP, TCP.
4. Enter a VPN Service Port to which a VPN device connects. The port number should
be between 1024 and 65535.
5. In the VPN Subnet/Netmask fields, enter the range of IP addresses that can be leased
to the device by the OpenVPN server.
63
Page 68
Chapter 14
VPN Server
6. Select your Client Access type. Select Home Network Only if you only want the
remote device to access your home network; select Internet and Home Network if
you also want the remote device to access the internet through the VPN Server.
7. Click Save.
8. Click Generate to get a new certificate.
Note: If you have already generated one, please skip this step, or click Generate to update the certificate.
9. Click Export to save the OpenVPN configuration file which will be used by the remote
device to access your router.
Step 2. Configure OpenVPN Connection on Your Remote Device
1. Visit http://openvpn.net/index.php/download/community-downloads.html to
download the OpenVPN software, and install it on your device where you want to run
the OpenVPN client utility.
Note:
You need to install the OpenVPN client utility on each device that you want to be able to use the VPN function. Mobile
devices should download a third-party app from Google Play or Apple App Store.
2. After the installation, copy the file exported from your router to the OpenVPN client
utility’s “config” folder (for example, C:\Program Files\OpenVPN\config on Windows).
The path depends on where the OpenVPN client utility is installed.
3. Run the OpenVPN client utility and connect it to OpenVPN Server.
14. 2. Use PPTP VPN to Access Your Home Network
PPTP VPN Server is used to create a VPN connection for remote devices. To use the
VPN feature, you should enable PPTP VPN Server on your router, and configure the
PPTP connection on the remote device. Please follow the steps below to set up a PPTP
VPN connection.
Step 1. Set up PPTP VPN Server on Your Router
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. Go to Advanced > VPN > PPTP VPN, and select Enable VPN Server.
64
Page 69
Chapter 14
Note:
Before you enable VPN Server, we recommend you configure Dynamic DNS Service (recommended) or assign a static
IP address for router’s WAN port and synchronize your System Time with internet.
VPN Server
3. In the Client IP Address field, enter the range of IP addresses (up to 10) that can be
leased to the devices by the PPTP VPN server.
4. Enter the Username and Password to authenticate clients to the PPTP VPN server.
5. Click Save.
Step 2. Configure PPTP VPN Connection on Your Remote Device
The remote device can use the Windows built-in PPTP software or a third-party PPTP
software to connect to PPTP Server. Here we use the Windows built-in PPTP software
as an example.
1. Go to Start > Control Panel > Network and Internet > Network and Sharing Center.
2. Select Set up a new connection or network.
3. Select Connect to a workplace and click Next.
65
Page 70
Chapter 14
VPN Server
4. Select Use my Internet connection (VPN).
5. Enter the internet IP address of the router (for example: 218.18.1.73) in the Internet
address field. Click Next.
66
Page 71
Chapter 14
VPN Server
6. Enter the Username and Password you have set for the PPTP VPN server on your
router, and click Connect.
7. The PPTP VPN connection is created and ready to use.
67
Page 72
Chapter 14
Modem router 1
LAN: 192.168.1.1
WAN: 219.134.112.246
PC 1
Subnetmask: 255.255.255.0
WAN: 219.134.112.247
Modem Router 2
PC 2
LAN: 192.168.2.1
Subnetmask: 255.255.255.0
Site A
Site B
WPS�ResetWIFI
USB LAN1 LAN2 LAN3
LAN4�WAN DSL
WPS�ResetWIFI
USB LAN1 LAN2 LAN3
LAN4�WAN DSL
VPN Server
14. 3. Use IPSec VPN to Access Your Home Network
IPSec VPN is used to create a VPN connection between local and remote networks.
To use IPSec VPN, you should check that both local and remote routers support IPSec
VPN feature. Then, follow the steps below to set up an IPSec VPN connection.
1. The typical VPN topology is here. Site A refers to local network, and Site B refers to
the remote network that is to be connected. Record Site A and Site B’s LAN and WAN
IP addresses before you start configuration.
2. Configuration on Site A (local network).
1 ) Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password
you set for the router.
2 ) Go to Advanced > VPN > IPSec VPN, and click Add.
68
Page 73
Chapter 14
VPN Server
3 ) In the IPSec Connection Name column, specify a name.
4 ) In the Remote IPSec Gateway (URL) column, Enter Site B’s WAN IP address.
5 ) Configure Site A’s LAN.
In the Tunnel access from local IP addresses column, we take Subnet Address
as an example. Input the LAN IP range of Site A in the IP Address for VPN column,
and input Subnet Mask of Site A.
6 ) Configure Site B’s LAN.
In the Tunnel access from remote IP addresses column, we take Subnet
Address as an example. Input the LAN IP range of Site B in the IP Address for
VPN column, and input Subnet Mask of Site B.
7 ) Select the Key Exchange Method for the policy. We select Auto(IKE) here.
69
Page 74
Chapter 14
VPN Server
8 ) Enter the Pre-Shared Key for IKE authentication. Then keep Perfect Forward
Secrecy enabled.
Note: Make sure Site A and Site B use the same key.
9 ) Leave the Advanced Settings as default value. Then click Save.
Note: The Status column is Down after the configuration, and it will change to UP only when Site A and Site B are
communicating via the VPN connection.
3. Configuration on Site B (remote network). Refer to step 2 configuration on Site A
and make sure that Site A and Site B use the same pre-shared keys and Perfect
Forward Secrecy settings.
4. Check the VPN connection. You can ping site B’ LAN IP from your computer in site
A to verify that the IPSec VPN connection is set up correctly.
Tips: To check the VPN connection, you can do the following.
1. On the host in Site A, press [Windows Logo] + [R] to open Run dialog. Input “cmd” and hit OK.
2. In the CLI window, type in “ping 192.168.2.x” (“192.168.2.x” can be IP address of any host in Site B). Then press [Enter].
3. If Ping proceeds successfully (gets replies from host in Site B), the IPSec connection is working properly now.
5. Now IPSec VPN is implemented to establish a connection.
70
Page 75
Chapter 14
Note:
1. The product supports a maximum of ten simultaneous connections.
2. If one of the site has been offline for a while, for example, if Site A has been disconnected, on Site B you need to click
Disable and then click Enable after Site A back on line in order to re-establish the IPSec tunnel.
VPN Server
71
Page 76
Chapter 15
Specify Your Network Settings
This chapter introduces how to change the default settings or adjust the basic
configuration of the modem router using the web management page.
It contains the following sections:
• LAN Settings
• IPv6 LAN Settings
• Wireless Settings
• Set Up a Dynamic DNS Service Account
• Create Static Routes
• Set Up the IPv6 Tunnel
Page 77
Chapter 15
Specify Your Network Settings
15. 1. LAN Settings
15. 1. 1. Change the LAN IP Address
The modem router is preset with a default LAN IP 192.168.1.1, which you can use to log
in to its web management page. The LAN IP address together with the Subnet Mask
also defines the subnet that the connected devices are on. If the IP address conflicts
with another device in your local network or your network requires a specific IP subnet,
you can change it.
Follow the steps below to change your IP address.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Network > LAN Settings page and select IPv4.
3. Type in a new IP Address appropriate to your needs.
4. Select the Subnet Mask from the drop-down list. The subnet mask together with
the IP address identifies the local IP subnet.
5. Keep IGMP Snooping enabled by default. IGMP snooping is the process of listening
to IGMP (Internet Group Management Protocol) network traffic. The function
prevents hosts on a local network from receiving traffic for a multicast group they
have not explicitly joined.
6. You can configure the modem router’s Second IP and Subnet Mask for LAN interface
through which you can also access the web management page.
7. Leave the rest of the default settings as they are.
8. Click Save to make the settings effective.
73
Page 78
Chapter 15
Specify Your Network Settings
15. 1. 2. Use the Modem Router as a DHCP Server
You can configure the modem router to act as a DHCP server to assign IP addresses to
its clients. To use the DHCP server function of the modem router, you must configure all
computers on the LAN to obtain an IP Address automatically.
Follow the steps below to configure DHCP server.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Network > LAN Settings page and select IPv4.
3. Select DHCP to enable the DHCP function and select DHCP Server.
4. Specify the IP Address Pool, the start address and end address must be on the
same subnet with LAN IP. The modem router will assign addresses within this
specified range to its clients. It is from 192.168.1.100 to 192.168.1.199 by default.
5. Enter a value for the Address Lease Time. The Address Lease Time is the amount of
time in which a DHCP client can lease its current dynamic IP address assigned by the
modem router. After the dynamic IP address expires, the user will be automatically
assigned a new dynamic IP address. The default is 1440 minutes.
6. Keep the rest of the settings as default and click Save.
Note:
1. The modem router can be configured to work as a DHCP Relay. A DHCP relay is a computer that forwards DHCP data
between computers that request IP addresses and the DHCP server that assigns the addresses. Each of the device’s
interfaces can be configured as a DHCP relay. If it is enabled, the DHCP requests from local PCs will be forwarded to
the DHCP server that runs on WAN side.
2. You can also appoint IP addresses within a specified range to devices of the same type by using Condition Pool
feature. For example, you can assign IP addresses within the range (192.168.1.50 to192.168.1.80) to Camera devices,
thus facilitating the network management. Enable DHCP feature and configure the parameters according to your
situation on the Advanced > Network > LAN Settings page.
74
Page 79
Chapter 15
Specify Your Network Settings
15. 1. 3. Reserve LAN IP Addresses
You can view and add a reserved address for a client. When you specify an IP address
for a device on the LAN, that device will always receive the same IP address each time
when it accesses the DHCP server. If there are some devices in the LAN that require
permanent IP addresses, please configure Address Reservation on the router for the
purpose.
Follow the steps below to reserve an IP address for your device.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Network > LAN Settings page and select IPv4.
3. Scroll down to locate the Address Reservation table and click Add to add an address
reservation entry for your device.
4. Click Scan and select the device for which you want to reserve IP address. Or enter
the MAC Address manually.
5. Specify the IP Address which will be reserved by the router.
6. Check to Enable this entry and click Save to make the settings effective.
15. 2. IPv6 LAN Settings
Based on the IPv6 protocol, the modem router provides two ways to assign IPv6 LAN
addresses:
• Configure the RADVD (Router Advertisement Daemon) address type
• Configure the DHCPv6 Server address type
75
Page 80
Chapter 15
Specify Your Network Settings
15. 2. 1. Configure the RADVD Address Type
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Network > LAN Settings.
3. Select IPv6 to configure IPv6 LAN parameters.
1 ) Select the RADVD address type to make the modem router assign IPv6 address
prefixes to hosts.
Note:
Do not select the Enable RDNSS and Enable ULA Prefix check boxes unless required by your ISP. Otherwise
you may not be able to access the IPv6 network. For more information about RDNSS and ULA Prefix, contact
our technical support.
2 ) Keep Site Prefix Type as the default value Delegated. If your ISP has provided a
specific IPv6 site prefix, select Static and enter the prefix.
3 ) Keep Prefix Delegated WAN Connection as the default value.
4. Click Save to make the settings effective.
15. 2. 2. Configure the DHCPv6 Server Address Type
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Network > LAN Settings.
3. Select IPv6 to configure IPv6 LAN parameters.
76
Page 81
Chapter 15
1 ) Select the DHCPv6 Server address type to make the modem router assign
IPv6 addresses to hosts.
Specify Your Network Settings
2 ) Specify the Start/End IPv6 Address for the IPv6 suffixes. The modem router will
generate IPv6 addresses within the specified range.
3 ) Keep Leased Time as the default value.
4 ) Keep Site Prefix Type as the default value Delegated. If your ISP has provided a
specific IPv6 site prefix, select Static and enter the prefix.
5 ) Keep Prefix Delegated WAN Connection as the default value.
4. Click Save to make the settings effective.
15. 3. Wireless Settings
15. 3. 1. Specify Basic Wireless Settings
The modem router’s wireless network name (SSID) and password, and security option
are preset in the factory. The preset SSID and password can be found on the product
label. You can customize the wireless settings according to your needs.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Basic > Wireless page.
77
Page 82
Chapter 15
Specify Your Network Settings
• To enable or disable the wireless function:
Enable the 2.4 GHz or 5GHz Wireless Network. If you don’t want to use the wireless
function, just deselect the box. If you disable the wireless function, all the wireless
settings won’t be effective.
• To change the wireless network name (SSID) and wireless password:
Enter a new SSID using up to 32 characters. The value is case-sensitive.
Note:
If you use a wireless device to change the wireless settings, you will be disconnected after the new settings are effective.
Please write down the new SSID and password for future use.
• To hide SSID:
Select Hide SSID, and your SSID will not be broadcast. Your SSID won’t display on your
wireless device when you scan for local wireless network list and you need to manually
join the network.
• To use the smart connect function
The smart connect function lets you to enjoy a more high-speed network by assigning
your devices to best wireless bands based on actual conditions to balance network
demands.
1. Go to Advanced > Wireless > Wireless Settings page.
2. Enable Smart Connect.
3. Keep the default or set a new SSID and password, and click Save. This SSID and
password will be applied both for 2.4GHz and 5GHz wireless networks.
78
Page 83
Chapter 15
Specify Your Network Settings
• To change the mode or channel:
Go to Advanced > Wireless > Wireless Settings page and select the wireless network
2.4GHz or 5GHz.
Mode: Select the desired mode.
• 802.11n only: Select only if all of your wireless clients are 802.11n devices.
• 802.11gn mixed: Select if you are using both 802.11g and 802.11n wireless clients.
• 802.11bgn mixed: Select if you are using a mix of 802.11b, 11g, and 11n wireless
clients.
Note: When 802.11n only mode is selected, only 802.11n wireless stations can connect to the modem router. It is
strongly recommended that you select 802.11bgn mixed, and all of 802.11b, 802.11g, and 802.11n wireless stations
can connect to the modem router.
• 802.11ac/n mixed (5GHz): Select if you are using both 802.11ac and 802.11n wireless
clients.
• 802.11a/n/ac mixed (5GHz): Select if you are using a mix of 802.11a, 802.11n and
802.11ac wireless clients. It is strongly recommended that you select 11a/n/ac mixed.
Channel: Select the channel you want to use from the drop-down list. This field
determines which operating frequency will be used. It is not necessary to change the
wireless channel unless you notice interference problems with another nearby access
point.
Channel Width: Select the channel width from the drop-down list. The default setting is
Automatic, which can adjust the channel width for your clients automatically.
79
Page 84
Chapter 15
Transmit Power: Select Low, Middle, or High to specify the data transmit power. The
default and recommended setting is High.
• To change the security option:
1. Go to Advanced > Wireless > Wireless Settings page.
2. Select the wireless network 2.4GHz or 5GHz.
3. Select an option from the Security drop-down list. The router provides four options,
None, WPA/WPA2 Personal (Recommended), WPA/WPA2 Enterprise, WEP. WPA2
uses the newest standard and the security level is the highest. We recommend you
don’t change the default settings unless necessary.
Specify Your Network Settings
15. 3. 2. Use WPS for Wireless Connection
You can use WPS (Wi-Fi Protected Setup) to add a new wireless device to your existing
network quickly and easily.
Method 1: Use the WPS button
Use this method if your client device has a WPS button.
1. Press the WPS button the modem router for 1 second.
2. Press the WPS button of the client device directly.
3. The WPS LED flashes for about 2 minutes during the WPS process.
4. When the WPS LED is on, the client device has successfully connected to the
modem router.
Method 2: Use the WPS button on the web management page
Use this method if your client device has a WPS button.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Wireless > WPS page.
3. Click Start WPS on the page.
4. Press the WPS button of the client device directly.
80
Page 85
Chapter 15
Specify Your Network Settings
5. The WPS LED of the router flashes for about 2 minutes during the WPS process.
6. When the WPS LED is on, the client device has successfully connected to the
modem router.
Method 3: Enter the modem router’s PIN on your client device
Use this method if your client device asks for the modem router’s PIN.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Wireless > WPS page. Click Method Two--PIN.
3. Take a note of the Current PIN of the modem router. You can also click the Generate
button to get a new PIN.
4. On the client device, enter the modem router’s PIN. (The default PIN is also printed
on the label of the modem router.)
5. The WPS LED flashes for about two minutes during the WPS process.
6. When the WPS LED is on, the client device has successfully connected to the
modem router.
Note:
1. The WPS LED on the modem router will light on for five minutes if the device has been successfully added to the
network.
2. The WPS function cannot be configured if the wireless function of the modem router is disabled. Please make sure
the wireless function is enabled before configuring WPS.
Method 4: Enter the client device’s PIN on the modem router
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Wireless > WPS page. Click Method Two--PIN.
81
Page 86
Chapter 15
Specify Your Network Settings
3. Select Client’s PIN.
4. Enter the client device’s PIN in the field. Then click the Connect button.
5. Connect successfully will appear on the above screen, which means the client
device has successfully connected to the modem router.
15. 3. 3. Schedule Your Wireless Function
You can automatically turn off your wireless network (both 2.4GHz and 5GHz) when you
do not need the wireless connection.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Wireless > Wireless Schedule page.
3. Toggle on the button to enable the Wireless Schedule feature.
4. Click Add to set the Wireless Off Time, and click Save to save the settings.
Note:
1. Make sure that the time of the router is correct before using this function. For details, refer to Set System Time.
2. The wireless LED (2.4GHz , 5GHz) will turn off if the corresponding wireless network is disabled.
3. The wireless network will be automatically turned on after the time period you set.
82
Page 87
Chapter 15
Specify Your Network Settings
15. 3. 4. View Wireless Information
• To view the detailed wireless network settings:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Status page. You can see the Wireless box.
3. Select 2.4GHz or 5GHz to view the wireless details.
Tips: You can also see the wireless details by clicking the router icon on Basic> Network Map.
• To view the detailed information of the connected wireless clients:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Wireless > Statistics page.
3. You can view the detailed information of the wireless clients, including its connected
wireless band and security option as well as the packets transmitted.
Tips: You can also see the wireless details by clicking the wireless clients icon on Basic > Network Map.
15. 3. 5. Advanced Wireless Settings
Advanced wireless settings are for those who have a network concept. If you are not
familiar with the settings on this page, it’s strongly recommended that you keep the
provided default values; otherwise it may result in lower wireless network performance.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Wireless > Advanced Settings page.
83
Page 88
Chapter 15
Specify Your Network Settings
• Beacon Interval: Enter a value between 25 and 1000 in milliseconds to determine the
duration between which beacon packets are broadcasted by the router to synchronize
the wireless network. The default is 100 milliseconds.
• RTS Threshold: Enter a value between 1 and 2346 to determine the packet size of
data transmission through the router. By default, the RTS (Request to Send) Threshold
size is 2346. If the packet size is greater than the preset threshold, the router sends
Request to Send frames to a particular receiving station and negotiates the sending
of a data frame, or else the packet will be sent immediately.
• DTIM Interval: Enter a value between 1 and 255 to determine the interval of the
Delivery Traffic Indication Message (DTIM). 1 indicates the DTIM Interval is the same
as Beacon Interval.
• Group Key Update Period: Enter the number of seconds to control the time interval
for the encryption key automatic renewal. The default is 0, indicating no key renewal.
• WMM: This feature guarantees the packets with high-priority messages being
transmitted preferentially. WMM is enabled compulsively under 802.11n or 802.11ac
mode.
• Short GI: This feature is enabled by default and recommended to increase the data
capacity by reducing the Guard Interval (GI) time.
• AP Isolation: Select this check box to enable the AP Isolation feature that allows you
to confine and restrict all wireless devices on your network from interacting with each
other, but still able to access the internet. AP isolation is disabled by default.
84
Page 89
Chapter 15
• WPS: Select this check box to enable the WPS feature. WPS (Wi-Fi Protected Setup)
provides you with an easier approach to set up a security-protected Wi-Fi connection.
Specify Your Network Settings
15. 4. Set Up a Dynamic DNS Service Account
Most ISPs (Internet service providers) assign a dynamic IP address to the router and
you can use this IP address to access your router remotely. However, the IP address
can change any time and you don’t know when it changes. In this case, you might need
the DDNS (Dynamic Domain Name Server) feature on the router to allow you and your
friends to access your router and local servers (FTP, HTTP, etc.) using domain name, in
no need of checking and remembering the IP address.
Note: DDNS does not work if the ISP assigns a private WAN IP address (such as 192.168.1.x) to the modem router.
To set up DDNS, please follow the instructions below:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Network > Dynamic DNS.
3. Select the DDNS service provider (TP-Link, Dyndns or NO-IP).
4. To use TP-Link DDNS service, you should log in with your TP-Link ID.
5. If you choose other DDNS service, you should also log in with your DDNS account,
select a service provider and click Go to register ... Enter the username, password
and domain name of the account (such as lisa.ddns.net).
6. Click Log in and Save.
Tips: If you want to use a new DDNS account, please Logout first, then login with the new account.
15. 5. Create Static Routes
A static route is a pre-determined path that network information must travel to reach
a specific host or network. Data from one point to another will always follow the same
85
Page 90
Chapter 15
Specify Your Network Settings
path regardless of other considerations. Normal internet usage does not require this
setting to be configured.
I want to:
Visit multiple networks and multiple servers at the same time.
For example, in a small office, my PC can surf the internet, but I also want to visit my
company’s server. Now I have a switch and another router. I connect the devices as
shown in the following figure so that the physical connection between my PC and my
company’s server is achieved. To surf the internet and visit my company’s network at
the same time, I need to configure the static routing.
Company’s server
172.30.30.1
LAN: 192.168.1.1
Router 2Modem router
USB LAN1 LAN2 LAN3
WPS�ResetWIFI
LAN4�WAN DSL
Switch
192.168.1.100
WPS�ResetWIFI
USB LAN1 LAN2 LAN3
My PC
WAN: 172.30.30.100
LAN4�WAN DSL
LAN: 192.168.1.2
How can I do that?
1. Make sure the routers use different LAN IP addresses on the same subnet. Disable
Router 2’s DHCP function.
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
3. Go to Advanced > Network > Static Routing. Select your current WAN Interface and
click Save.
4. Click Add to add a new static routing entry. Finish the settings according to the
following explanations:
86
Page 91
Chapter 15
• Network Destination: The destination IP address that you want to assign to a static
route. This IP address cannot be on the same subnet with the WAN IP or LAN IP of the
router. In the example, the IP address of the company network is the destination IP
address, so here enters 172.30.30.1.
Specify Your Network Settings
• Subnet Mask: Determines the destination network with the destination IP address.
If the destination is a single IP address, enter 255.255.255.255; otherwise, enter the
subnet mask of the corresponding network IP. In the example, the destination network
is a single IP, so here enters 255.255.255.255.
• Gateway: The IP address of the gateway device to which the data packets will be sent.
This IP address must be on the same subnet with the router’s IP which sends out the
data. In the example, the data packets will be sent to the LAN port of Router 2 and then
to the Server, so the default gateway should be 192.168.1.2.
• Interface: Determined by the port (WAN/LAN) that sends out the data packets. In the
example, the data is sent to the gateway through the LAN port, so LAN should be
selected.
5. Select the check box to enable this entry.
6. Click OK to save the settings.
Done!
Open a web browser on your PC. Enter the company server’s IP address to visit the
company network.
15. 6. Set Up the IPv6 Tunnel
The IPv6 Tunnel feature helps you obtain IPv6 resources based on an IPv4 WAN
connection or vice versa.
87
Page 92
Chapter 15
Specify Your Network Settings
IPv6 Tunnel is a transition mechanism that enables IPv6-only hosts to reach IPv4
services or vice versa and allows isolated IPv6 hosts and networks to reach each other
over IPv4-only infrastructure before IPv6 completely supplants IPv4. It is a temporary
solution for networks that do not support native dual-stack, where both IPv6 and IPv4
run independently.
The modem router provides three tunneling mechanisms: 6to4, 6rd and DS-Lite. The
way to set up 6rd and DS-Lite tunnel are similar.
15. 6. 1. Use the Public IPv6 Tunnel Service-6to4
The 6to4 tunnel is a kind of public service. If there are any 6to4 servers on your network,
you can use this mechanism to access IPv6 service. If your ISP provides you with an
IPv4-only connection but you want to visit IPv6 websites, you can try to set up a 6to4
tunnel.
I want to:
Set up the IPv6 tunnel though my ISP doesn’t provide me with the tunnel service.
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Network > IPv6 Tunnel.
3. Tick the check box, select 6to4 as the tunneling mechanism and select a WAN
connection from the drop-down list, then click Save.
Note:
If there is no available WAN connection to choose, make sure you have connected to the internet and the
connection type is not Bridge.
Done!
Now you can visit the IPv6 websites with the 6to4 tunnel.
Note:
Still not being able to access IPv6 resources means that not any 6to4 public server was found in your network. You can
contact your ISP to sign up for IPv6 connection service.
88
Page 93
Chapter 15
Specify Your Network Settings
15. 6. 2. Specify the 6rd Tunnel with Parameters Provided by Your ISP
I want to:
Specify the 6rd tunnel with the parameters provided by my 6rd tunnel service provider.
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID and the password you
set for the router.
2. Go to Advanced > Network > IPv6 Tunnel.
3. Tick the check box, select 6rd as the tunneling mechanism and select a WAN
connection from the drop-down list.
4. According to the parameters provided by your ISP, choose Auto or Manual. More
parameters are needed if you choose Manual.
5. Click Save.
Note:
If there is no available WAN connection to choose, make sure you have connected to the internet and the
connection type is not Bridge.
Done!
Now you can visit the IPv6 websites with the 6rd tunnel.
Tips:
The way to set up DS-Lite tunnel is similar to that of 6rd tunnel. If you are provided with an IPv6-only WAN connection
and have signed up for DS-Lite tunnel service, specify the DS-Lite tunnel by referring to the steps above.
89
Page 94
Chapter 16
Administrate Your Network
This chapter introduces how to change the system settings and administrate your
modem router’s network.
This chapter contains the following sections:
• Set System Time
• Update the Firmware
• Back up and Restore Configuration Settings
• Reboot the Router
• Change the Administrator Account
• Local Management
• Remote Management
• System Log
• Monitor the Internet Traffic Statistics
• CWMP Settings
• SNMP Settings
Page 95
Chapter 16
Administrate Your Network
16. 1. Set System Time
System time is the time displayed while the modem router is running. The system time
you configure here will be used for other time-based functions like Parental Controls
and Wireless Schedule. You can manually set how to get the system time.
Follow the steps below to set your system time.
1. Visit http://tplinkmodem.net, and log in with your TP-Link and the password you set
for the router.
2. Go to Advanced > System Tools > Time Settings page.
3. Configure the system time using the following methods:
Manually: Select your time zone and enter your local time.
Get from PC: Click this button if you want to use the current managing PC’s time.
Get GMT: Click this button if you want to get time from the internet. Make sure your
modem router can access the internet before you select this way to get system
time.
4. Click Save.
5. After setting the system time, you can set Daylight Saving Time according to your
needs. Tick the check box to enable Daylight Saving Time, set the start and end
time and then click Save to make the settings effective.
91
Page 96
Chapter 16
Administrate Your Network
16. 2. Update the Firmware
TP-Link is dedicated to improving product features, giving you a better network
experience.
We will inform you through the web management page if there’s any update firmware
available for your router. The latest firmware can also be downloaded from the Support
page of our website www.tp-link.com for free.
Note:
1. Make sure that you have a stable connection between the router and your computer. It is NOT recommended to
upgrade the firmware wirelessly.
2. Make sure you remove any USB storage device connected to the router before the firmware upgrade to prevent data
loss.
3. Back up your router configuration before upgrading the firmware.
4. Do NOT turn off the router during the firmware upgrade.
16. 2. 1. Online Upgrade
1. Visit http://tplinkmodem.net, and log in with your TP-Link and the password you set
for the router.
2. If there’s any firmware update available for your router, the update icon
on the top-right corner of the page. Click the icon to go to the Firmware Upgrade
page.
Alternatively, you can go to Advanced > System Tools > Firmware Upgrade,
and click Check for Upgrades to see if there’s any new firmware.
Tips:
If there’s any new important firmware update for your router, you will see the notification (similar as shown below)
on your computer when open a new web page. Click Upgrade now, and log into the web management page. You
will see the Firmware Upgrade page.
will display
92
Page 97
Chapter 16
3. Wait a few moments for the upgrading and rebooting.
Administrate Your Network
16. 2. 2. Local Upgrade
1. Download the latest firmware file for the router from our website www.tp-link.com.
2. Visit http://tplinkmodem.net, and log in with your TP-Link and the password you set
for the router.
3. Go to Advanced > System Tools > Firmware Upgrade.
4. Focus on the Device Information section. Make sure the downloaded firmware file
matches with the Hardware Version.
5. Focus on the Local Upgrade section. Click Browse to locate the downloaded new
firmware file, and click Upgrade.
6. Wait a few moments for the upgrading and rebooting.
16. 3. Back up and Restore Configuration Settings
The configuration settings are stored as a configuration file in the router. You can back
up the configuration file to your computer for future use and restore the modem router
to a previous settings from the backup file when needed. Moreover, if needed you can
erase the current settings and reset the modem router to the default factory settings.
• To back up configuration settings
1. Visit http://tplinkmodem.net, and log in with your TP-Link and the password you set
for the router.
2. Click Advanced > System Tools > Backup & Restore page.
3. Click Backup to save a copy of the current settings to your local computer. A conf.
bin file will be stored to your computer.
93
Page 98
Chapter 16
Administrate Your Network
• To restore configuration settings
1. Visit http://tplinkmodem.net, and log in with your TP-Link and the password you set
for the router.
2. Click Advanced > System Tools > Backup & Restore page.
3. Click Browse to locate the previous backup configuration file, and click Restore.
4. Wait for the restoring and then the modem router will automatically reboot.
• To reset the modem router to factory default settings
1. Visit http://tplinkmodem.net, and log in with your TP-Link and the password you set
for the router.
2. Click Advanced > System Tools > Backup & Restore page.
3. Click Restore to restore all configuration settings to default values, except your
login and TP-Link ID information. Click Factory Restore to reset the modem router.
4. Wait for the reset process to complete, and then the modem router will automatically
reboot.
Note:
1. During the resetting process, do not turn off the modem router.
2. We strongly recommend you back up the current configuration settings before resetting the modem router.
16. 4. Reboot the Router
The Reboot feature cleans the cache to enhance the running performance of the router.
1. Visit http://tplinkmodem.net, and log in with your TP-Link and the password you set
for the router.
2. Click Advanced > System Tools > Reboot page.
• To Reboot Manually
Locate the Manual Reboot section and click Reboot.
94
Page 99
Chapter 16
Administrate Your Network
• To Reboot Automatically
1. Locate the Reboot Schedule section and check the box to enable Reboot Schedule.
2. Specify the Reboot Time when the router reboots and Repeat to decide how often
it reboots.
Note:
Before enabling Reboot Schedule, please make sure your router is connected to the internet, then go to Advanced >
Time Settings and choose Get from the Internet to get the correct network time.
3. Click Save.
16. 5. Change the Administrator Account
Admin account is used to log in to the modem router’s web management page. You are
required to set the admin account at first login. You can also change it on the web page.
1. Visit http://tplinkmodem.net, and log in with your TP-Link and the password you set
for the router.
2. Go to Advanced > System Tools > Administration page. Locate the Account
Management section.
3. Enter the old password. Enter the new password and enter again to confirm.
95
Page 100
Chapter 16
Administrate Your Network
4. Click Save to make the settings effective.
16. 6. Local Management
You can control the local devices’ authority to manage the modem router via Local
Management feature. By default all local connected devices are allowed to manage
the modem router. You can also specify one device to manage the modem router and
enable local management over a more secure way, HTTPS.
Follow the steps below to allow only the specific device to manage the router via the
local management over HTTPS.
1. Visit http://tplinkmodem.net, and log in with your TP-Link and the password you set
for the router.
2. Go to Advanced > System Tools > Administration page. Locate the Local
Management section.
3. Keep the Port as the default setting. Enable Management over HTTPS and keep the
Port for HTTPS as the default setting. Enter the IP address or MAC address of the
local device to manage the modem router.
4. Click Save.
Now, you can manage the modem router over both HTTP (http://tplinkmodem.net) and
HTTPS (https://tplinkmodem.net).
Note:
If you want that all local devices can manage the modem router, just leave the IP/MAC Address field blank.
16. 7. Remote Management
By default, the remote devices are not allowed to manage the modem router from the
internet. You can enable remote management over HTTP and/or HTTPS if needed.
HTTPS is a more secure way to access the router.
Note:
If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), you cannot use the remote management
feature because private addresses are not routed on the internet.
96
Loading...