Toyota TUNDRA 2003, TUNDRA 2004 Owner's Manual
2003- TUNDRA TVIP V3 RS3200
Remote Keyless
S
ecurity system
D
esigned Specifically for
y
our
Vehicle
owner’s guide
RS3200
Rev. D 5/09/01
2005-2006 COROLLA/MATRIX TVIP V3 RS3200
OWNER'S GUIDE
OWNER’S GUIDE
To better understand the features and functions of this security system, please read this
Owner’s Guide completely prior to use.
TABLE OF CONTENTS
DESCRIPTION PAGE
INTRODUCTION
2
REMOTE CONTROL INFORMATION
THE REMOTE CONTROL INCLUDED WITH YOUR SYSTEM 3
BRIEF DESCRIPTION–RS3200 FEATURES 4, 5
OPERATION
ARMING THE RS3200 (except PASSIVE ARMING) 6
DISARMING THE RS3200 (except PASSIVE DISARMING) 7
PASSIVE (AUTOMATIC) ARMING & DISARMING 8
AUTOMATIC REARMING 9
ARMING SUSPENSION 9
MISCELLANEOUS
DOOR AJAR WARNING 10
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 10
REMOTE CONTROL RANGE 10
ALARM INFORMATION
PANIC MODE OPERATION 11
ALARM TRIGGERS 12
ALARM DESCRIPTIONS 13
STOPPING AN ALARM 13
GLASS BREAKAGE SENSOR INFORMATION
GLASS BREAKAGE SENSOR CHECK PROCEDURE 14
PROGRAMMING
PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY 15
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION 16, 17
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 18
REMOTE CONTROL BATTERY REPLACEMENT
REMOVE THE BATTERY 19
INSTALL THE BATTERY 20
WARNING AND CAUTION INFORMATION 21
TOYOTA RS3200 remote keyless Security system Page 1
INTRODUCTION
Congratulations on your choice of the RS3200 remote keyless security system to protect your
vehicle! To get the most from the system, we strongly recommend that you read this Owner’s
Guide completely to learn all of its features and functions.
The RS3200 provides the convenience of remote keyless operation, enabling you to A
RM and
D
ISARM at the same time you remotely lock and unlock the doors. The system provides comprehen-
sive security protection through point-of-entry monitoring, glass breakage detection and ignition
switch monitoring. While A
RMED, the system will be TRIGGERED and sound an ALARM when a door,
trunk or hatch is forcibly unlocked or opened*, or when a window is tapped on or broken. During
the A
LARM, the vehicle’s horn sounds and the headlights, tail lights and front marker lights flash.
A l s o , the vehicle’s starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the STATUS MONITOR
for this system. Illustrated
below, this panel holds the LED indicator (for the system’s operating status) and the G
LASS
BREAKAGE SENSOR’S microphone. In vehicles with an engine immobilizer, there is already a LED
installed in the vehicle, so the RS3200 utilizes the engine immobilizer system LEDand a microphone mounted in a separate location. If your vehicle falls into this category, remember to look at
that LED when the information refers to the S
TATUS MONITOR. If you do not know where the LED is
located, refer to your vehicle’s owner’s guide for specific information.
About the ignition-controlled automatic door locking/unlocking function.
The RS3200 is programmed to automatically lock your vehicle’s doors when you turn the key in
the ignition switch to the “ON” or “START” position, and unlock them when you turn the key back
to the “ACC” or “LOCK” position. You may disable this feature by reprogramming the system; refer
to page 18 for programming information.
* When the system is P
ASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will
elapse when a door is opened before an A
LARM is TRIGGERED.
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE
ILLUSTRATED HERE
LIGHTS FOR
30 SECONDS
(PRE-ARMING)
THEN STARTS
FLASHING
(SYSTEM IS
ARMED
)
Page 2 TOYOTA RS3200 REMOTE KEYLESS Security system
TOYOTA RS3200 remote keyless Security system Page 19
REMOTE CONTROL BATTERY REPLACEMENT
The following shows the procedure to replace the batteries in your remote controls. We recom-
mend that you replace the batteries at least once a year, or when the remote control’s transmitting
range diminishes. You may obtain the replacement battery from your Toyota dealer, as well as
many retailers that sell watch batteries.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.
REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
2. Using a coin, pry open the remote control.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
REMOTE CONTROL INFORMATION
THE REMOTE CONTROLS PROVIDED WITH YOUR SYSTEM
The 3 button remotes included with your system have separate LOCK and UNLOCK buttons on the
front
and a PANIC button on the back .
The RS3200 may be controlled by as many as 4 remote controls, so you may add two additional
remote controls to the two included with your system. Contact your Toyota dealer for more details.
TOYOTA RS3200 remote keyless Security system Page 3
Front Button
FLASHES WHEN
BUTTONS PRESSED
PUSH TO LOCK
DOORS AND ARM
SYSTEM
PUSH TO UNLOCK
DOORS AND DISARM
SYSTEM
Back Button
HOLD TO ACTIVATE
PANIC MODE
OPERATION
NOTE: This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful inter
ference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accor
dance with the instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be deter
mined by turning the equipment off and on, the user is encouraged to try
and correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION (continued)
3. Select the Operating Mode and Complete the Programming Procedure.
Note: If the system locks the doors twice, start over.
Page 4
TOYOTA
RS3200 REMOTE KEYLESS Security system
TOYOTA
FEATURES
FUNCTIONS
The RS3200 will ARM30 seconds after the LOCK button on the
remote control is pressed, and D
ISARM
when the UNLOCK button is
pressed. When the LOCK button is pressed, all the vehicle’s doors
lock. When the UNLOCK button is pressed, the driver’s door
unlocks,* but if the UNLOCK button is pressed again within 3
seconds, the remaining doors unlock.
The RS3200 will automatically R
ELOCK
the vehicle’s doors if no door
is opened within 30 seconds after R
EMOTEDISARMING
, then will R
EARM
30 seconds later.
The RS3200 will A
RM
30 seconds after you close the trunk (if open)
and lock the vehicle’s doors with the key, and will D
ISARM
when you
unlock a door with the key.
While A
RMED
, the trunk may be opened with the key (or the AUX
button on your remote control, if so equipped) without T
RIGGERING
an
A
LARM
. Once the open trunk is closed, the system A
RMS
again.
(See page 9 for more information.)
The RS3200 may be programmed to automatically A
RM
30 seconds
after the ignition key is removed, the vehicle exited and the last door
and the trunk closed, without the necessity of locking the doors.
The RS3200 may be D
ISARMED
with the vehicle’s ignition key after it
was P
ASSIVELYARMED
.
When the RS3200 has been P
ASSIVELYARMED
, an E
NTRYDELAY
(userselectable at 0, 15, or 30 seconds) will start when a door is opened
before an A
LARM
is T
RIGGERED
.
When you lock the vehicle with a central lock switch (while a
door is open), the RS3200 will A
RM
30 seconds after you close all
the doors and the trunk (if open).
The RS3200 may be D
ISARMED
by inserting the key into the ignition
switch and turning it to “ON.”
Forcibly unlocking or opening a door, hatch or trunk while the
RS3200 is A
RMED
will T
RIGGER
an A
LARM
immediately. (If the system
was P
ASSIVELYARMED
, the E
NTRYDELAY
must pass before the A
LARM
is
T
RIGGERED
.)
The RS3200 utilizes a microphone (usually mounted in the S
TATUS
M
ONITOR
) to sense the noise from tapping on window glass, or
glass breaking, and T
RIGGER
an A
LARM
. It is fine tuned to “listen” for
this type of noise, and ignore other sounds.
When the G
LASSBREAKAGESENSOR’S
microphone picks up tapping or
breaking of window glass, it T
RIGGERS
a W
ARNAWAYALARM
; the
headlights and tail and marker lights flash, and the horn sounds for
20 seconds, but the starter is not disabled. If there is another
detection of glass tapping or breaking, or if a door is opened or
unlocked without a key, the regular A
LARM
is T
RIGGERED
.
While A
RMED
, the RS3200 monitors the ignition switch. If an attempt
is made to start the vehicle without a key, an A
LARM
is triggered.
** Starting from 2002 M.Y., Arming Suspension Mode by using the key to unlock the trunk is not
applicable to Camry, Solara, and Corolla.
* You may program the system to unlock all the doors with one press on the UNLOCK button.
See page 16 for programming instructions.
REMOTE
ARMING/DISARMING &
LOCKING/UNLOCKING
AUTOMATIC
REARMING
KEY
ARMING/DISARMING
ARMED MODE
SUSPENSION **
PASSIVE (AUTOMATIC)
ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
GLASS BREAKAGE
SENSOR
WARN AWAY ALARM
IGNITION SWITCH
MONITORING
BRIEF DESCRIPTION–RS3200 FEATURES
a. Press and
release
both
LOCK and
UNLOCK
buttons at the
same time.
i. The tail and marker lights flash 1 time, the
buzzer
chirps 1 time, and the doors lock and
unlock
1 time.
TOYOTA RS3200 remote keyless Security system Page 5
FEATURES FUNCTIONS
When an ALARM is TRIGGERED, the system disables the vehicle’s
starter and prevents engine start until the system is reset (D
ISARMED).
During an A
LARM, the system will lock the doors if one is unlocked,
and will continue to do so for the duration of the A
LARM.
The user is notified that an A
LARM occurred. Upon DISARMING the
system after an A
LARM was TRIGGERED, the vehicle’s tail and marker
lights will be turned on, and the B
UZZER sounds, for 2 seconds.
You may T
RIGGER a PANIC ALARM, by pressing the PANIC button on the
back of the remote control, to draw attention to your vehicle. During
the P
ANIC ALARM, the head, tail and marker lights flash, and the horn
sounds, but the starter is not disabled.
The RS3200 flashes the vehicle’s tail and marker lights during
R
EMOTE ARMING and REMOTE DISARMING, as well as during an ALARM.
Also, the headlights flash during an A
LARM.
When the system is R
EMOTE DISARMED, it turns on the interior lights in
the vehicle for 30 seconds, or until the key is inserted into the
ignition switch. It also turns them on during an A
LARM.
During an A
LARM, the RS3200 activates the vehicle’s horn.
If power to the RS3200 is disrupted while it is A
RMED, an ALARM
is TRIGGERED once power is restored.
This panel houses the G
LASS BREAKAGE SENSOR microphone and the
flashing LED that indicates the operating status of the security system.
(In vehicles with an engine immobilizer system, that system’s LED and
a separate microphone are used instead.)
The RS3200 utilizes a P
IEZO BUZZER, usually mounted in the engine
compartment, to sound confirmation “chirps” and tones for function
confirmation and programming step confirmation.
The RS3200 automatically locks your vehicle’s doors when you turn
the ignition key to “ON” or “START”, and unlocks the doors when you
turn the key back to “ACC” or “LOCK”.*
The Buzzer sounds for 5 seconds when you attempt to R
EMOTE ARM
the system while a door is open. You can stop the warning by closing
the door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with
the RS3200 is approximately 50 feet. Please refer to page 10 for a
description of factors that may affect the performance (operating
range) of the remote controls.
* You may disable this feature. Please refer to page 18 for programming information.
STARTER DISABLE
FORCED LOCK
DURING ALARM
TRIGGER MEMORY
PANIC MODE
OPERATION
EXTERIOR LIGHT
ACTIVATION
INTERIOR LIGHT
ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-CONTROLLED
AUTOMATIC DOOR
LOCK/UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
BRIEF DESCRIPTION–RS3200 FEATURES
Page 6 TOYOTA RS3200 REMOTE KEYLESS Security system
TOYOTA RS3200 remote keyless Security system Page 15
OPER ATION
ARMING THE RS3200 (except PASSIVE ARMING)
The system may be ARMED in several ways. Do
one
of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the trunk or hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing.
The system is now ARMED.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the trunk or hatch, if necessary.* Then:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing.
The system is now ARMED.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the trunk or hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The STATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing.
The system is now ARMED.
* The system will not A
RM while any of the doors, trunk or hatch is open. However, when you press
the LOCK button when the trunk is open, the doors will lock; the system will arm 30 seconds
after the trunk is closed.
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE
THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE
THE DOOR IS OPEN
LIGHTS FOR
30 SECONDS
(PRE-ARMING)
THEN
FLASHES
(SYSTEM IS
ARMED
)
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
ALL DOORS LOCK WHEN THE
SYSTEM IS REMOTE ARMED
PROGR A M M I NG
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to not PASSIVELY ARM. To change the system’s operation for PASSIVE
ARMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more
information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
a. Using the remote control,
lock, then unlock the
doors
3 times.
a. Close, then Open the door:
2 times = P
ASSIVE ARMING OFF
3 times = PASSIVE ARMING ON,
0 Sec. E
NTRY DELAY
4 times = PASSIVE ARMING ON,
15 Sec. E
NTRY DELAY
5 times = PASSIVE ARMING ON,
30 Sec. E
NTRY DELAY
d. The system locks the door
in 2 seconds; if this does
not happen, start over.
THE BUZZER CHIRPS ONCE WHEN
THE SYSTEM IS REMOTE ARMED
Loading...