Toyota AVALON 2007 Owner Manual

SECTION 1−

OPERATION OF INSTRUMENTS AND CONTROLS

Overview of instruments and controls

Instrument panel overview 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Instrument cluster o verview 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Center cluster overview 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Indicator symbols on the instrument panel 9. . . . . . . . . . . . . . . . . . . . . . .

Instrument panel overview

View A

1. Side vents

2. Side defroster o utlets

3. Instrument cluster

4. Center cluster

5. Garage door opener switches

6. Auxiliary boxes

7. Front personal lights, interior light and/or electric moon roof switches

8. Center vents

9. Glove box

10. Power door lock switches

11. Power window switches

12. Trunk opener main switch

13. Rear console box

14. Rear vents

15. Power outlets

16. Seat ventilator/heater switches

17. Cup holder

18. Automatic transmission selector lever

19. Tire pressure warning reset switch (On bott om of the instrument panel)

20. Hood lock release lever

21. Parking b rake pedal

22. Window lock switch

23. Drivi ng position memory switches

View B (with key cylinder−type ignition switch)

1. Instrument panel light control knob

2. Headlight, turn signal and front fog light switches

3. Audio remote control switches

4. Speech command switch (See the separate “Navigation System Owner’s Manual.”)

5. Climate remote control switches

6. Wiper and washer switches

7. Rear window and outside rear view mirror defogger switch

8. Emergency flasher switch

9. Audio system

10. Air conditioning controls

11. Cigarette lighter and ashtray, auxiliary box, cassette player or navigation system controller (For the navigation system, see the separate “Navigation System Owner’s M anual.”)

12. Ignition switch

13. Cruise control switch

14. Tilt steering lock release lever

15. Telescopic steering lock release lever

16. Glass breakage sensor

17. Trunk opener switch

18. Fuel filler door opener switch

19. Power rear view mirror control switches

View B (with smart key system)

1. Instrument panel light control knob

2. Headlight, turn signal and front fog light switches

3. Audio remote control switches

4. Speech command switch (See the separate “Navigation System Owner’s Manual.”)

5. Climate remote control switches

6. Wiper and washer switches

7. Rear window and outside rear view mirror defogger switch

8. Emergency flasher switch

9. Audio system

10. Air conditioning controls

11. Cigarette lighter and ashtray, auxiliary box, cassette player or navigation system controller (For the navigation system, see the separate “Navigation System Owner’s M anual.”)

12. Ignition switch (engine switch)

13. Cruise control switch

14. Distance switch

15. Tilt steering lock release lever

16. Telescopic steering lock release lever

17. Glass breakage sensor

18. Rear electric sunshade switch

19. Trunk opener switch

20. Fuel filler door opener switch

21. Power rear view mirror control switches

Instrument cluster overview

1. Engine coolant temperature gauge

2. Service reminder indicators and indicator lights

3. Tachometer

4. Speedometer

5. Fuel gauge

6. Low fuel level warning light

7. Trip m eter res et knob

8. Odometer and two trip meters

9. Automatic transmission shift range position display

10. Dynamic laser cruise control display

11. Dynamic laser cruise control master warning light

Center cluster overview

1. Clock

∗

2. Center display

3. Front passenger’s seat belt reminder

∗

light

∗

: If your vehicle is equipped with navigation system, see the separate “Navigation System Owner’s Manual”.

∗

: For details, see “Service reminder indicators and warning buzzers” on page 145 in Section 1−6.

4. “AIRBAG ON” and “AIRBAG OFF” indicator lights

5. Pattern selector knob (for center display)

Indicator symbols on the instrument panel

∗

Brake system warning light

Open door warni ng light

∗

SRS war ning light

∗

Driver’s seat belt reminder light

Charging system warning light

Low engine oil press ure warning light

Malfunction indicator lamp

Anti−lock brake system warning light

∗

Vehicle stability control system and traction control system warni ng li ght

Low tire pressure warning light

Low windshield washer fluid level warning

∗

light Automatic headlight leveling system warning

∗

light

Engine oil replacement reminder light

Smart key system warning light

∗

Engine immobilizer/theft deterrent system indicator light

Headlight indicator light

Tail light indicator light

Headlight high beam indicator light

Turn signal indicator lights

Automatic transmission indicator lights

Slip indicator/traction control system off light

∗

Cruise control indicator light cruise control indicator light

or dynamic laser

∗

Dynamic laser cruise control ready mode indicator light

Conventional cruise control mode indicator light

∗

: For details, see “Service reminder indicators and warning

buzzers” on page 145 in Section 1−6.

∗

: If this light flashes, see “Cruise control” on page 176 in

Section 1−7.

∗

: If this light flashes, see “Dynamic laser cruise control” on

page 179 in Section 1−7.

SECTION 1−

OPERATION OF INSTRUMENTS AND CONTROLS

Keys and Doors

Keys 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine immobilizer system 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wireless remote control 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Smart key system 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Side doors 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power windows 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Trunk lid 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hood 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Theft deterrent system 49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel tank cap 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electric moon roof 52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Keys (with key cylinder−type ignition switch)

A transponder chip for engine immobilizer system has been placed in the head of the master and sub keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys. If you make your own duplicate key, you will not be able to cancel the system or start the engine.

To protect items locked in the trunk or glove box when using valet parking, leave the sub key with the attendant.

Your vehicle is supplied with two kinds of keys.

1. Master keys (black)—These keys work in every lock. Your Toyota dealer will need one of them to make a new key with a built−in transponder chip.

2. Sub key (gray)—This key will not work in the locks of the glove box and the door located behind the rear seat armrest.

NOTICE

When using a key containing a transponder chip, observe the following precautions:



When starting the engine, do not use the key with a key ring resting on the key grip and do not press the key ring against the key grip. Otherwise the engine may not start, or may stop soon after it starts.



When starting the engine, do not use the key with other transponder keys around (including keys of other vehicles) and do not press other key plates against the key grip. Otherwise the engine may not start, or may stop soon after it starts. If this happens, remove the key once and then insert it again after removing other transponder keys (including keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine.



Do not bend the key grip.



Do not cover the key grip with any material that cuts off electromagnetic waves.



Do not knock the key hard against other objects.



Do not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under direct sunlight.



Do not put the key in water or wash it in an ultrasonic washer.



Do not use the key with electromagnetic materials.

KEY NUMBER PLATE Your key number is shown on the plate.

Keep the plate in a safe place such as your wallet, not in the vehicle.

If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number.

We recommend writing down the key number and storing it in a safe place.

Keys (with smart key system)

The key consists of an electronic key and a mechanical key. The mechanical key is for emergency use. If the electronic key does not operate, you can open the driver’s door using the mechanical key.

1. Electronic keys—These keys can lock or unlock all the doors and can open the trunk by using the wireless remote control function or entry function of the smart key system.

2. Mechanical keys—These keys can lock or unlock the driver’s door, the glove box and the door located behind the rear seat armrest.

Spare keys should not be left in the cabin. In the event that a spare key is left in the cabin, the smart key system will remain actuated even after the doors have been locked. Under these circumstances, the trunk can be opened even after the driver has exited and locked the vehicle, increasing the danger of theft. (Refer to “OPENING TRUNK WITH SMART KEY SYSTEM” on page 45 in this Section.)

To protect items locked in the trunk or the glove box when using valet parking, lock the trunk opener switch and leave the electronic key with the attendant. Keep the mechanical key with you. For details about locking the trunk opener switch, see “—Luggage security system” on page 46 in this Section.

A transponder chip for engine immobilizer system has been placed in the electronic keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys.

CAUTION

 People with implanted pacemakers

or cardiac defibrillators should keep away from the smart key system antennas, because the radio waves may affect the operation of such devices. For the antenna locations see “ANTENNA LOCATION” on page 29 in this Section.

 Users of any electrical medical de-

vice other than implanted pacemakers and implanted cardiac defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.

 If necessary, the entry function can

be disabled. See “DISABLING THE SMART KEY SYSTEM” on page 33 in this Section.

NOTICE

When using a electronic key containing a transponder chip, observe the following precautions:



Do not affix any material that cuts off electromagnetic waves (such as a metal seal) on the electronic key.



Do not knock the electronic key hard against other objects.



Do not leave the electronic key exposed to high temperatures for a long period, such as on the dashboard or hood under direct sunlight.



Do not put the electronic key in water or wash it in an ultrasonic washer.



Do not keep the electronic key together with the products emitting electromagnetic waves such as a cellular phone.

USING A MECHANICAL KEY

When you use the mechanical key push the release button and take out the mechanical key as shown. Be sure to put the mechanical key back when not it use.

Engine immobilizer system

The engine immobilizer system is a theft prevention system using an electronic code. The transponder chip in the key has an electronic code and transmits the code to the vehicle. Only when the electronic code in the chip corresponds to the register ID code for the vehicle, the engine immobilizer system will be canceled and the engine will start.

KEY NUMBER PLATE Your key number is shown on the plate.

Keep the plate in a safe place such as your wallet, not in the vehicle.

If you should lose your keys or if you need additional keys, duplicates can be made by Toyota dealer using the key number.

We recommend writing down the key number and storing it in a safe place.

The engine immobilizer system is automatically set when:

Vehicles with key cylinder−type ignition switch—The key is removed from the ignition switch.

Vehicles with smart key system—The ignition switch is turned off.

The indicator light will start flashing to show that the system is set.

If any of the following indicator conditions occur, contact your Toyota dealer.

 The indicator light remains on.  The indicator light does not start flash-

ing under the following situations. Vehicles with key cylinder−type ignition

switch—When the key is removed from the ignition switch.

Vehicles with smart key system—When the ignition switch is turned off.

 The indicator light flashes inconsistent-

ly.

The engine immobilizer system is automatically canceled when:

Vehicles with key cylinder−type ignition switch— You insert the key to the ignition switch.

Vehicles with smart key system— You enter the vehicle carrying a key with smart key system and press the “ENGINE START STOP” switch (engine switch).

Even if the key battery is discharged, the engine can be started. See “Smart key system” on page 27 in this Section.

When the system is canceled, the indicator light will go off.

For your Toyota dealer to make you a new key with built−in transponder chip, your dealer will need your key number and master key (vehicles with key cylinder−type ignition switch) or electronic key (vehicles with smart key system). However, there is a limit to the number of additional keys your Toyota dealer can make for you.

NOTICE

Do not modify, remove or disassemble the engine immobilizer system. If any unauthorized changes or modifications are made, proper operation of the system cannot be guaranteed.

For vehicles sold in U.S.A.

FCC ID: MOZRI−21BTY FCC ID: NI4TMIMB−1

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For vehicles sold in Canada

This device complies with RSS−210 of Industry Canada. Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Wireless remote control—

1. Lock switch

2. Unlock switch

3. Alarm switch

4. Trunk opener switch

5. Indicator light (vehicles with smart key system only)

Vehicles with key cylinder−type ignition switch

Vehicles with smart key system

The wireless remote control function is designed to lock or unlock all the doors, open the trunk lid, or activate the alarm from a distance within approximately 1 m (3 ft.) of the vehicle.

When you operate any switch, push it slowly and securely.

Vehicles with smart key system only— When the switch is operated, the indicator light flashes once. If not, the battery may be discharged. Replace the battery at the earliest opportunity.

The wireless remote control transmitter is an electronic component. Observe the following instructions in order not to cause damage the key.

 Do not leave the transmitter in places

where the temperature becomes high such as on the dashboard.

 Do not disassemble it.  Avoid knocking it hard against other

objects or dropping it.

 Avoid putting it in water.

You can use up to 4 wireless remote control transmitters (for vehicles with key cylinder−type ignition switch) or 7 wireless remote control transmitters (for vehicles with smart key system) for the same vehicle. Contact your Toyota dealer for detailed information.

If the wireless remote control transmitter does not actuate the doors, or does not operate from a normal distance, or if the indicator on the transmitter is dimmed or does not come on:

 Check for closeness to a radio trans-

mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.

 The battery may have been consumed.

Check the battery in the transmitter. To replace the battery, see “—Replacing battery” on pages 24 or 25 in this Section.

If you lose your transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an accident. (See “If you lose your wireless remote control transmitter” on page 332 in Section 4.)

For vehicles sold in U.S.A.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

—Locking and unlocking doors

NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving an-

tenna.

 Increase the separation between the

equipment and receiver.

 Connect the equipment into an outlet

on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced

radio/TV technician for help.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For vehicles sold in Canada

Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Locking operation (vehicles with key cylinder−type ignition switch)

Unlocking operation (vehicles with key cylinder−type ignition switch)

Locking operation (vehicles with smart key system)

Unlocking operation (vehicles with smart key system)

To lock or unlock all the doors, push the switches slowly and securely.

To lock: Push the lock switch. All the doors are locked simultaneously. At this time one beep will sound and turn signal lights flash once.

Vehicles with smart key system—For 3 seconds after the doors have been locked, the doors cannot be re−unlocked via the smart key system.

Check to see that the doors are securely locked.

If any of the doors is not securely closed, or if the key is in the ignition switch (vehicles with key cylinder−type ignition switch) or key left in the vehicle (vehicles with smart key system), locking cannot be performed by the lock switch and a beep will sound continuously for 10 seconds.

To stop the beep, take out the key from the vehicle or push the unlock switch.

To unlock: Push the unlock switch once to unlock the driver’s door alone. Pushing the switch twice within 3 seconds unlocks all the doors simultaneously. Each time the unlock switch is pushed, two beeps will sound and turn signal lights flash twice.

This double switch operation to unlock all doors can be changed to a single switch operation. For details, contact your Toyota dealer.

If the key is in the ignition (vehicles with key cylinder−type ignition switch) or the ignition switch is set to ACC or ON (vehicles with smart key system), the vehicle cannot be unlocked via the unlock switch.

When all the doors are unlocked simultaneously with a key, wireless remote control or entry function of the smart key system, the following lights come on for about 15 seconds and then fade out, even if the door is not opened.

Vehicles with key cylinder−type ignition switch—Ignition switch light, interior light, front personal lights and rear personal lights Vehicles with smart key system—Interior light, front personal lights, rear personal lights and exterior foot lights

(For further information, see “Illuminated entry system” on page 135 in Section 1−5.)

You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the doors will be automatically locked again.

If the wireless remote control is used to lock the doors near the window or door handle, there is a possibility that the door may not unlocked by entry function of smart key system. Under these circumstances, use the wireless remote control to unlock the doors.

The time before automatic door lock function can be changed. For details, contact your Toyota dealer.

If the lock or unlock switch is kept pressed in, the locking or unlocking operation is not repeated. Release the switch and then push again.

—Opening trunk lid

The following adjustments can be made in this system. For details, contact your Toyota dealer.

 Cancelling the wireless door locking or

unlocking function

 Cancelling the flash of the turn signal

lights

 Cancelling the beep sound

Vehicles with key cylinder−type ignition switch

Vehicles with smart key system

To open the trunk lid, push the trunk opener switch of the transmitter for 1 second. A long beep will sound.

If the key is in the ignition (vehicles with key cylinder−type ignition switch) or the ignition switch is set at ACC or ON (vehicles with smart key system), the trunk lid cannot be opened by the trunk opener switch.

Opening of the trunk lid with the wireless remote control can be changed as follows. Contact your Toyota dealer for details.

 Trunk lid opens by pushing the trunk

opener switch twice in succession.

 Trunk lid opens by pushing the trunk

opener switch once regardless of how long the switch is being pressed.

 Opening of the trunk lid is disabled

using the wireless remote control transmitter.

—Activating alarm

Vehicles with key cylinder−type ignition switch

Pushing the alarm switch for 1 second blows the horn intermittently and flashes the headlights, turn signal lights, tail lights and interior light.

Vehicles with smart key system only—When pushing the switch, the indicator light flashes.

The alarm switch is used to deter vehicle theft when you witness anyone attempting to break into or damage your vehicle.

The alarm will last for one minute. To stop the alarm midway, push the switch once again, unlock a door with the transmitter, or set the ignition switch to ON.

If the key is in the ignition (vehicles with key cylinder−type ignition switch) or the ignition switch is set at ACC or ON (vehicles with smart key system), the alarm does not work.

This alarm function can be disabled. For details, contact your Toyota dealer.

Vehicles with smart key system

—Replacing battery (with key cylinder−type ignition switch)

For replacement, use a CR2016 lithium battery or equivalent.

CAUTION

Special care should be taken to prevent small children from swallowing the removed transmitter battery or components.

NOTICE



When replacing the transmitter battery, be careful not to lose the components.



Replace only with the same or equivalent type recommended by a Toyota dealer.



Dispose of used batteries according to the local laws.

Replace the transmitter battery by following these procedures:

1. Using a coin or equivalent, open the transmitter case.

2. Remove the circuit board, then remove the discharged transmitter battery.

NOTICE



Take care not to damage the circuit board.



Do not bend the terminals.



Be careful not to bend the electrode when inserting the transmitter battery and that dust or oils do not adhere to the transmitter case.



Close the transmitter case securely.

—Replacing battery (with smart key system)

The transmitter can easily be damaged when replacing the battery. We recommend having the battery replaced by your Toyota dealer. If you have to do it yourself, use a CR1632 lithium battery or equivalent and a flathead screwdriver.

3. Put in a new transmitter battery with positive (+) side up. Install the circuit board into the transmitter case.

Close the transmitter case securely.

NOTICE



Make sure the positive side and negative side of the transmitter battery are faced correctly.



Do not replace the battery with wet hands. Water may cause unexpected rust.



Do not touch or move any components inside the transmitter, or it may interfere with proper operation.

After replacing the battery, check that the transmitter operates properly. If the transmitter still does not operate properly, contact your Toyota dealer.

CAUTION

Special care should be taken to prevent small children from swallowing the removed transmitter battery or components.

NOTICE



Be careful not to touch the circuit, as this may generate static electricity that can damage the transmitter.



When replacing the transmitter battery, be careful not to lose the components.



Replace only with the same or equivalent type recommended by a Toyota dealer.



Dispose of used batteries according to the local laws.

Replace the transmitter battery by following these procedures:

1. Push the release button and take out the mechanical key.

2. Using a flathead screwdriver or equivalent, open the transmitter case.

3. Remove the discharged transmitter battery by flathead screwdriver or equivalent. Insert the guide groove and lift as shown in the above illustration.

NOTICE

Do not modify the battery case. It may cause a trouble.

4. Put in a new battery with the positive (+) side up. Install the cover and insert the mechanical key into the transmitter.

Close the transmitter case securely.

NOTICE



Make sure the positive side and negative side of the battery are faced correctly.



Do not replace the battery with wet hands. Water may cause unexpected rust.



Do not touch or move any components inside the transmitter, or it may interfere with proper operation.



Be careful not to bend the electrode when inserting the transmitter battery and that dust or oils do not adhere to the case.



Close the transmitter case securely.

After replacing the battery, check that the transmitter operates properly. If the transmitter still does not operate properly, contact your Toyota dealer.

Smart key system

The smart key system consists mainly of the following functions.

 Engine immobilizer function (For de-

tails, see “Engine immobilizer system” on page 16 in this Section.)

 Wireless remote control function (For

details, see “Wireless remote control” on page 18 in this Section.)

 Push button start function (For details,

see “How to start the engine” on page 296 in Section 3.)

 Entry function and start function (See

“ENTRY FUNCTION AND START FUNCTION” described below.)

 Steering lock function (See “STEERING

LOCK FUNCTION” described below.)

CAUTION

 People with implanted pacemakers

 Users of any electrical medical de-

 If necessary, the entry function can

be disabled. See “DISABLING THE SMART KEY SYSTEM” on page 33 in this Section.

Entry function

ENTRY FUNCTION AND START FUNCTION

By carrying the key, you can lock and unlock the doors and start the engine.

Entry function—You can lock and unlock

the doors and open the trunk without inserting the key in the keyhole. For further information, see “Side doors” on page 34 and “Trunk lid” on page 44 in this Section.

Start function—You can shift the power supply mode and start the engine when the electronic key is in the vehicle. For further information, see “Ignition switch” on page 159 in Section 1−7 and “How to start the engine ”on page 296 in Section

Start function

STEERING LOCK FUNCTION

When the driver’s door is opened after turning off the engine, the steering wheel will lock.

The steering lock is automatically unlocked when the “ENGINE START STOP” switch (engine switch) is pressed. If the indicator light on the “ENGINE START STOP” switch flashes green, this indicates that the steering wheel remains locked. If the amber indicator light flashes, this indicates that the steering lock is malfunctioning. For details, see “How to start the engine” on page 296 and “Driving and parking using smart key system” on page 300 in Section 3.

ANTENNA LOCATION

1. Antenna inside cabin and trunk

2. Antenna outside cabin and trunk

ACTUATION AREA The entry function and start function

are available to use when a registered key is in the actuation area.

1. Entry function actuation area—About

1 m (3 ft.) from each outside door handle and trunk opener switch.

If the key is close to a door handle, a window, the center of the rear bumper, on the ground or above the roof, the entry function may not operate properly.

2. Start function actuation area—Inside of the cabin.

The start function may not be activated if the key is on the instrument panel, on the package tray, in the glove box or on the floor, etc.

In the following cases, the smart key system may not operate properly.

 When facilities issuing strong electro-

magnetic waves such as TV towers, electric power stations, broad casting stations are nearby.

 In places where automated payment fa-

cilities are installed (such as gas stations).

 When you are carrying an electronic

key together with a mobile communications system such as a two−way radio or cellular phone.

 When the electronic key is in contact

with or covered by a metallic object.

 When another person is operating a

wireless remote control function on another vehicle near your vehicle.

 When the battery is discharged. To re-

place the battery, see “—Replacing battery” on page 25 in this Section.

 When the electronic key is near a

high−voltage or noise−emitting device.

 When you are carrying an electronic

key together with a key for another smart key system equipped vehicle or another instrument emitting radio waves.

 Depending on the position of the key

or vehicle body shape the key may not work well even within the actuation area.

 When the key surface is covered by a

sticker, etc. that may cut off electromagnetic wave.

If the smart key system does not operate properly and you cannot enter, you can lock and unlock all the doors by using mechanical key attached to the master key or wireless remote control function.

+ 331 hidden pages