4RUNNER 2005
’05 4Runner_U (L/O 0411)
SECTION 1-
OPERATION OF INSTRUMENTS AND
CONTROLS
Overview of instruments and controls
Instrument panel overview 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument cluster overview 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicator symbols on the instrum ent panel 7. . . . . . . . . . . . . . . . . . . . . . .
1
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
1
Instrument panel overview
’05 4Runner_U (L/O 0411)
1. Side vents
2. Side defroster o utlets
3. Instrument cluster
4. Center vents
5. Personal lights
6. Electric moon roof switch
7. Garage door opener
8. Auxiliary boxes
9. Glove box
10. Automatic transmission selector lever
11. Power door lock switches
12. Power window switches
13. Seat heater switches
14. “HEIGHT CONTROL OFF” switch
15. Rear vents
16. Trash holder
17. Height select switch
18. “DAC” switch
19. Front cup holders
20. Tilt steering lock release lever
2
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
21. Telescopic steering lock release lever
22. Parking b rake pedal
23. Window lock switch
24. Power rear view mirror control switches
’05 4Runner_U (L/O 0411)
Rear console box
1. Power outlet (12 VDC)
2. Power outlet (115 VAC)
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
3
’05 4Runner_U (L/O 0411)
1. Instrument panel light control dial
2. Headlight, turn signal and front fog
light switches
3. Audio remote control switches
4. Wiper and washer switches
5. Power back window switch
6. Audio system/rear view monitor system
and navigat ion system includi ng audio
system (For the navigation system, see
the separate “Navigation System
Owner’s Manual”.)
7. Front passenger’s seat belt reminder
light
8. Engine immobilizer/theft deterrent
system indicator light
9. Front passenger occupant classification
indicator light
10. Multi- information display
11. Emergency flasher switch
12. Air conditioning controls
13. Auxiliary box
14. Back window and outside rear view
mirror defogger switch
15. Four- wheel drive control switch knob
(full- time four- wheel drive models) or
multi- mode control switch knob
(multi- mode four- wheel drive models)
4
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
16. Ignition switch
17. Cruise control switch
18. Hood lock release lever
19. Fuel filler door opener
20. Roll s ensing of curt ain shield air bags
off switch
21. “AUTO LSD” switch
22. Center differential lock switch
23. Power outlet main switch
’05 4Runner_U (L/O 0411)
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
5
Instrument cluster overview
’05 4Runner_U (L/O 0411)
1. Trip meter reset button
2. Tachometer
3. Service reminder indicators and
indicator lights
6
4. Speedometer
5. Fuel gauge
6. Low fuel level warning light
7. Engine coolant temperature gauge
8. Odometer and two trip meters
9. Odometer/two trip meter changeover
button
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
Indicator symbols on the instrument panel
∗
Brake system warning light
Driver’s seat belt reminder light
Front passenger’s seat belt reminder light
Dischar ge warning light
Low engine oil press ure warning light
1
∗
1
∗
1
∗
’05 4Runner_U (L/O 0411)
Vehicle stability control system warning
∗
1
light
∗
Traction control system warning light
(two- wheel drive models)
Active traction control system warning light
∗
1
(four- wheel drive models)
“AUTO LSD” system warning light
(two- wheel drive models)
Downhill assist control system warning
∗
1
(four- wheel drive models)
light
1
Hill- start assist control system warning
∗
1
light
1
∗
1
∗
1
∗
Malfunction indicator lamp
Engine oil replacement reminder light
(for vehicles sold in U.S.A.)
or
Anti- lock brake system warning light
1
∗
1
∗
1
Open door warni ng light
SRS war ning light
Automatic transmission fluid temperature
warning light
∗
1
(four- wheel drive models)
Low tire pressure warning light
∗
1
∗
1
∗
1
7
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
’05 4Runner_U (L/O 0411)
Low windshield washer fluid level warning
∗
1
light
(for vehicles sold in Canada)
Engine immobilizer/theft deterrent system
indicator light
Roll sensing of curtain shi eld airbags off
indicator light
∗
2
Front passenger occupant classification indicator
light
Headlight low beam indicator light
Tail light indicator light
Headlight high beam indicator light
Turn signal indicator lights
Automatic transmission indicator lights
∗
Low speed four- wheel drive indicator light
3
(four- wheel drive models)
∗
Center differential lock indicator light
3
(four- wheel drive models)
Vehicle stability control system off indicator light
(four- wheel drive models)
∗
Four- wheel drive indicator light
3
(multi- mode four- wheel drive models)
Slip indicator light
“AUTO LSD” indicator light
(two- wheel drive models)
Downhill assist control system indicator light
(four- wheel drive models)
Height control indicator lights
8
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
∗
Height control “OFF” indicator light
Cruise control indicator light
∗
1
: For details, see “Service reminder indicators and warning
∗
4
5
buzzers” on page 145 in Section 1- 6.
∗
2
: For details, see “Roll sensing of curtain shield airbags off
switch” on page 94 in Section 1- 3.
∗
3
: If this light flashes, see “Four- wheel drive system” on page
162 in Section 1- 7.
∗
4
: If this light flashes, see “Rear height control air suspension”
on page 182 in Section 1- 7.
∗
5
: If this light flashes, see “Cruise control” on page 193 in
Section 1- 7.
’05 4Runner_U (L/O 0411)
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
9
’05 4Runner_U (L/O 0411)
10
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
’05 4Runner_U (L/O 0411)
SECTION 1-
OPERATION OF INSTRUMENTS AND
CONTROLS
Keys and Doors
Keys 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine immobilizer system 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless remote control 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side doors 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power windows 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power back window 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back door 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Theft deterrent system 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel tank cap 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric moon roof 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
11
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
Keys
’05 4Runner_U (L/O 0411)
To protect items locked in the glove box
when using valet parking, leave the sub
key with the attendant.
Since the side doors can be locked without a key, you should always carry a
spare key in case you accidentally lock
your keys inside the vehicle.
Your vehicle is supplied with the two
kinds of keys.
1. Master keys (black)—These keys work
in every lock. Your Toyota dealer will
need one of them to make a new key
with a built- in transponder chip.
2. Sub key (gray)—This key does not
work in the glove box.
A transponder chip for engine immobilizer
system has been placed in the head of
the master and sub keys. These chips are
needed to enable the system to function
correctly, so be careful not to lose these
keys. If you make your own duplicate key,
you will not be able to cancel the system
or start the engine.
12
NOTICE
When using a key containing a transponder chip, observe the following
precautions:
When starting the engine, do not
use the key with a key ring resting
on the key grip and do not press
the key ring against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts.
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
When starting the engine, do not
use the key with other transponder
keys around (including keys of other vehicles) and do not press other
key plates against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts. If
this happens, remove the key once
and then insert it again after removing other transponder keys (including keys of other vehicles) from the
ring or while gripping or covering
them with your hand to start the
engine.
’05 4Runner_U (L/O 0411)
Do not bend the key grip.
Do not cover the key grip with any
material that cuts off electromagnetic waves.
Do not knock the key hard against
other objects.
Do not leave the key exposed to
high temperatures for a long period,
such as on the dashboard and hood
under direct sunlight.
Do not put the key in water or
wash it in an ultrasonic washer.
Do not use the key with electromagnetic materials.
13
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
’05 4Runner_U (L/O 0411)
Engine immobilizer system
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by a Toyota dealer using the key
number.
We recommend writing down the key number and storing it in a safe place.
14
The engine immobilizer system is a
theft prevention system. When you insert the key in the ignition switch, the
transponder chip in the key’s head
transmits an electronic code to the vehicle. The engine will start only when
the electronic code in the chip corresponds to the registered ID code for
the vehicle.
The system is automatically set when the
key is removed from the ignition switch.
The indicator light will start flashing to
show the system is set.
If any of the following indicator conditions
occurs, contact your Toyota dealer.
The indicator light stays on except
when the theft deterrent system is setting or activating. (See “Theft deterrent
system” on page 34 in this Section.)
The indicator light does not start flash-
ing when the key is removed from the
ignition switch.
The indicator light flashes inconsistent-
ly.
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
Inserting the registered key in the ignition
switch automatically cancels the system,
which enables the engine to start. The
indicator light will go off.
For your Toyota dealer to make you a
new key with built- in transponder chip,
your dealer will need your key number
and master key. However, there is a limit
to the number of additional keys your
Toyota dealer can make for you.
If you make your own duplicate key,
you will not be able to cancel the system or start the engine.
NOTICE
Do not modify, remove or disassemble the engine immobilizer system. If any unauthorized changes or
modifications are made, proper operation of the system cannot be guaranteed.
’05 4Runner_U (L/O 0411)
For vehicles sold in U.S.A.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
For vehicles sold in Canada
Wireless remote control—
1. “LOCK” switch
2. “UNLOCK” switch
3. Back window open switch
4. “PANIC” switch
This device complies with RSS-210 of
Industry Canada. Operation is subject to
the following two conditions:
(1) this device may not cause interference, and (2) this device must accept
any interference, including interference
that may cause undesired operation of
the device.
15
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
The wireless remote control system is
designed to lock or unlock all the side
doors and back door, open the back
window or activate the “PANIC” mode
from a distance within approximately 1
m (3 ft.) of the vehicle.
When you operate any switch, push it
slowly and securely.
The wireless remote control transmitter is
an electronic component. Observe the following instructions in order not to cause
damage to the transmitter.
Do not leave the transmitter in places
where the temperature becomes high
such as on the dashboard.
Do not disassemble it.
Avoid knocking it hard against other
objects or dropping it.
Avoid putting it in water.
You can use up to 4 wireless remote control transmitters for the same vehicle.
Contact your Toyota dealer for detailed
information.
’05 4Runner_U (L/O 0411)
If the wireless remote control transmitter
does not actuate the doors, back window
or alarm, operate from a normal distance:
Check for closeness to a radio trans-
mitter such as a radio station or an
airport which can interfere with normal
operation of the transmitter.
The battery may have been consumed.
Check the battery in the transmitter. To
replace the battery, see following
“—Replacing battery” on page 20.
If you lose your transmitter, contact your
Toyota dealer as soon as possible to
avoid the possibility of theft, or an accident. (See “If you lose your wireless remote control transmitter” on page 349 in
Section 4.)
—Locking and unlocking
doors
Locking operation
16
Unlocking operation
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
’05 4Runner_U (L/O 0411)
To lock and unlock all the side doors
and back door, push the switches of
the transmitter slowly and securely.
To lock: Push the “LOCK” switch. All the
side doors and back door are locked simultaneously. At this time one beep will
be heard, and the turn signal lights flash
once.
Check to see that all the side doors and
back door are securely locked.
If any of the side doors or the back door
is not securely closed, locking cannot be
performed by the “LOCK” switch and a
beep will sound continuously for 10 seconds. However, if the key is in the ignition
switch, a beep will not sound.
To stop the buzzer, close all the side
doors and back door securely or push the
“UNLOCK” switch.
The buzzer can be disabled. For details,
contact your Toyota dealer.
To unlock: Push the “UNLOCK” switch
once to unlock the driver’s door alone.
Pushing the switch twice within 3 seconds
unlocks all the side doors and back door
simultaneously. Each time the “UNLOCK”
switch is pushed, two beeps will be heard,
and the turn signal lights flash twice.
This double switch operation to unlock all
the side doors and back door can be
changed to a single switch operation. For
details, contact your Toyota dealer.
When the “UNLOCK” switch is pressed,
the interior light, luggage compartment
light, ignition switch light and running
board lights (on some models) will come
on and remain on for about 15 seconds
before fading out. (For details, see “Interior light” on page 134, “Luggage compartment light” on page 135, “Ignition switch
light” on page 136 and “Running board
lights” on page 137 in Section 1- 5.)
You have 30 seconds to open a door after
using the wireless remote unlock feature.
If a door is not opened by then, all the
side doors and back door will be automatically locked again.
The timing for the automatic door lock
function can be changed. For details, contact your Toyota dealer.
If the “LOCK” or “UNLOCK” switch is kept
pressed in, the locking or unlocking operation is not repeated. Release the switch
and then push again.
The following adjustments can be made in
this system. For details, contact your
Toyota dealer.
Cancelling the wireless door locking or
unlocking function
Cancelling the flash of the turn signal
lights
Changing the volume of beep sound
17
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
’05 4Runner_U (L/O 0411)
—Opening back window —Activating panic mode
The “PANIC” mode does not work when
the ignition key is in the “ON” position.
This alarm function can be disabled. For
details, contact your Toyota dealer.
To open the back window, push the
back window open switch of the transmitter for about 1 second. The window
will fully open.
At this time, you can hear a beep.
If the ignition switch is in the “ON” posi-
tion, the back window cannot be opened
by the back window open switch.
To open the back window with the key,
see “Power back window” on page 29 in
this Section.
The back window opening program by
wireless remote control can be changed or
disabled. For details, contact your Toyota
dealer.
18
Pushing the “PANIC” switch blows the
horn intermittently and flashes the
headlights, tail lights and turn signal
lights, and turns on the interior and
luggage compartment lights.
The “PANIC” switch is used to deter vehicle theft when you witness anyone attempting to break into or damage your
vehicle.
The alarm will last for one minute. To stop
alarm midway, push any of the switch on
the wireless remote control transmitter.
You can also stop the alarm by turning
the ignition key from the “LOCK” to “ON”
position.
2005 4RUNNER from Nov. ’04 Prod. (OM35841U)
’05 4Runner_U (L/O 0411)
For vehicles sold in U.S.A.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
NOTICE:
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is
no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving an-
tenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet
on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced
radio / TV technician for help.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
19
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
For vehicles sold in Canada
Operation is subject to the following two
conditions:
(1) this device may not cause interference, and (2) this device must accept
any interference, including interference
that may cause undesired operation of
the device.
’05 4Runner_U (L/O 0411)
—Replacing battery
For replacement, use a CR2016 lithium
battery or equivalent.
CAUTION
Special care should be taken to prevent small children from swallowing
the removed transmitter battery or
components.
NOTICE
When replacing the transmitter battery, be careful not to lose the components.
Replace only with the same or
equivalent type recommended by a
Toyota dealer.
Dispose of used batteries according
to the local laws.
1. Using a coin or equivalent, open the
transmitter case.
20
Replace the transmitter battery by following these procedures:
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
’05 4Runner_U (L/O 0411)
Be careful not to bend the electrode
when inserting the transmitter battery and that dust or oils do not
adhere to the transmitter case.
Close the transmitter case securely.
After replacing the battery, check that the
transmitter operates properly. If the transmitter still does not operate properly, contact your Toyota dealer.
2. Remove the discharged transmitter battery by ballpoint pen.
Insert the tip of ballpoint pen at the
guide groove and lift as shown in the
above illustration.
NOTICE
Do not bend the terminals.
3. Put in a new transmitter battery with
positive (+) side up.
Close the transmitter case securely.
NOTICE
Make sure the positive side and
negative side of the transmitter battery are faced correctly.
Do not replace the battery with wet
hands. Water may cause unexpected
rust.
Do not touch or move any components inside the transmitter, or it
may interfere with proper operation.
21
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
Side doors—
’05 4Runner_U (L/O 0411)
When any of the side doors and back
door is unlocked with a key, the interior
light, luggage compartment light, ignition
switch light and running board lights (on
some models) will come on and remain on
for about 15 seconds before fading out.
(For details, see “Interior light” on page
134, “Luggage compartment light” on page
135, “Ignition switch light” on page 136
and “Running board lights” on page 137
in Section 1-5.)
LOCKING AND UNLOCKING WITH KEY
Insert the key into the keyhole and turn
it.
To lock: Turn the key forward.
To unlock: Turn the key backward.
All the side doors and back door lock and
unlock simultaneously with the driver’s
door. In the driver’s door lock, turning the
key once will unlock the driver’s door and
twice in succession will unlock all the side
doors and back door simultaneously.
This double key turning operation to unlock all the side doors and back door can
be changed to a single key turning operation. For details, contact your Toyota dealer.
22
LOCKING AND UNLOCKING WITH
INSIDE LOCK KNOB
Move the lock knob.
To lock: Push the knob forward.
To unlock: Pull the knob backward.
The front doors can be opened by pulling
the inside handles even if the lock knobs
are in the locked position.
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
’05 4Runner_U (L/O 0411)
CAUTION
Do not pull the inside handle of the
front doors while driving. The doors
will open and an accident may occur.
Toyota strongly recommends that all
children be placed in the rear seat of
the vehicle.
Closing the door with the lock knob in the
lock position will also lock the door. Be
careful not to lock your keys in the vehicle.
The front doors cannot be locked if you
leave the key in the ignition switch.
Driver’s side
Front passenger ’s side
LOCKING AND UNLOCKING WITH
POWER DOOR LOCK SWITCH
Push the switch.
To lock: Push the switch down on the
front side.
To unlock: Push the switch down on the
rear side.
Operating the switch simultaneously locks
or unlocks all the side doors and back
door.
If you do either of the following, no side
door or back door can be unlocked with
the power door lock switch.
Lock all the side doors and back door
with the key or wireless remote control
transmitter when all the side doors and
back door are closed.
Open the driver’s door or front passen-
ger’s door and move the inside lock
knobs of both front doors to the lock
position, then close the front doors.
23
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
’05 4Runner_U (L/O 0411)
The power door lock switch can be reset
in the following ways.
Turn the ignition key to “ON”.
Unlock all the side doors and back
door with the key or wireless remote
control transmitter.
Unlock the driver’s door or front pas-
senger’s door with the inside lock
knob, and then unlock all the side
doors and back door with the power
door lock switch.
This unlocking protection with the power
door lock switch can be disabled. For details, contact your Toyota dealer.
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the vehicle. Along with the proper use of
seat belts, locking the doors helps
prevent the driver and passengers
from being thrown out from the vehicle in an accident. It also helps prevent the doors from being opened
unintentionally.
REAR DOOR CHILD- PROTECTORS
Move the lock lever to the “LOCK”
position as shown on the label.
When the child-protector is locked, you
cannot open the rear door by the inside
door handle. We recommend using this
feature whenever small children are in the
vehicle.
24
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
—Automatic door locking and
unlocking functions
You can set the following automatic
door locking and unlocking functions.
(a) Locking linked with the shift posi-
tion
All the side doors and back door are
locked automatically when the automatic
transmission selector lever is moved out
of the “P” position with the engine running
and all the side doors and back door are
closed. This function is the default setting
for new vehicles.
(b) Unlocking linked with the shift posi-
tion
All the side doors and back door are unlocked automatically when the automatic
transmission selector lever is moved to
the “P” position with the ignition switch in
the “ON” position.
(c) Locking linked with the vehicle
speed
All the side doors and back door are
locked automatically when the vehicle
speed reaches 20 km/h (12 mph) or higher. However, if any of the side doors and
back door is unlocked during driving, this
auto locking function will not operate until
the unlocked door is opened once.
’05 4Runner_U (L/O 0411)
(d) Unlocking linked with opening the
driver’s door
All the side doors and back door are unlocked automatically when the driver’s
door is opened within 10 seconds after
the ignition switch is turned from the “ON”
to “ACC” or “LOCK” position.
SETTING THE FUNCTIONS
1. Close all the side doors and back door.
2. Turn the ignition switch to the “ON”
position.
3. Within 10 seconds after the ignition
switch is turned to the “ON” position;
To set function (a)
Push and hold the front of the power
door lock switch for 5 seconds with the
automatic transmission selector lever in
the “P” position.
To set function (b)
Push and hold the rear of the power
door lock switch for 5 seconds with the
automatic transmission selector lever in
the “P” position.
To set function (c)
Push and hold the front of the power
door lock switch for 5 seconds with the
automatic transmission selector lever in
any position except “P”.
To set function (d)
Push and hold the rear of the power
door lock switch for 5 seconds with the
automatic transmission selector lever in
any position except “P”.
All the side doors and back door are automatically lock and unlock when you release the power door lock switch. This
indicates that the function is set. If all the
side doors and back door do not lock and
unlock, the time the switch was held may
have been too short or too long. Perform
the procedure over again starting from
step 1.
If you want to cancel a function, repeat
the procedure. Each time you perform the
procedure, the function is set or cancelled.
25
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
Power windows
’05 4Runner_U (L/O 0411)
OPERATING THE DRIVER’S WINDOW
Use the switch on the driver’s door.
Normal operation: The window moves as
long as you hold the switch.
To open: Lightly push down the switch.
To close: Lightly pull up the switch.
The windows can be operated with the
switch on each side door.
The power windows work when the ignition
switch is in the “ON” position.
Key off operation: If both front doors are
closed, all the power windows work for 43
seconds even after the ignition switch is
turned off. It stops working when either
front door is opened.
The indicator light (“AUTO”) on the switch
tells you the switch can be operated.
26
Automatic operation: Push the switch
completely down or pull it completely up,
and then release it. The window will fully
open or close. To stop the window partway, lightly move the switch in the opposite direction and then release it.
Jam protection function: During automatic closing operation or key off closing operation, the window stops and opens half
way if something gets caught between the
window and window frame.
If the window receives a strong impact,
this function may work even if nothing is
caught.
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
If the battery is disconnected or run
down, the power window may not operate
automatically and the jam protection function will not function correctly after you
reconnect, replace or recharge the battery.
In any of these cases, you should normalize the power window.
To normalize the power window:
1. Push down the power window switch
and lower the window halfway.
2. Pull up the switch until the window
closes and hold the switch for a second.
Make sure that the window opens and
closes automatically. If the power window
cannot be operated properly, have it
checked by your Toyota dealer.
’05 4Runner_U (L/O 0411)
Window
lock
switch
CAUTION
Never try jamming any part of your
body to activate the jam protection
function intentionally.
The jam protection function may
not work if something gets caught
just before the window is fully
closed.
27
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
’05 4Runner_U (L/O 0411)
OPERATING THE PASSENGERS’
WINDOWS
Use the switch on each passenger’s
door or the switches on the driver’s
door that control each passenger’s window.
The window moves as long as you hold
the switch.
To open: Push down the switch.
To close: Pull up the switch.
If you push in the window lock switch on
the driver’s door, the passengers’ windows
cannot be operated.
CAUTION
To avoid serious personal injury, you
must do the following.
Before you close the power win-
dows, always make sure there is
nobody around the power windows.
You must also make sure the
heads, hands and other parts of the
bodies of all occupants are kept
completely inside the vehicle. If
someone’s neck, head or hands get
caught in a closing window, it
could result in death or serious injury. When anyone closes the power
windows, make sure he or she operates the windows safely.
When small children are in the ve-
hicle, never let them use the power
window switches without supervision. Use the window lock switch to
prevent them from making unexpected use of the switches.
Be sure to remove the ignition key
when you leave your vehicle.
Never leave anyone (particularly a
small child) alone in your vehicle,
especially with the ignition key still
inserted. Otherwise, he/she could
use the power window switches and
get trapped in a window. Unattended person (particularly a small
child) can be involved in a serious
accident.
28
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
Power back window
The back window can be operated with
the switch on the instrument panel or
the key operation in the back door keyhole.
The power back window works when the
ignition switch is in the “ON” position.
You can open the back window when the
back window wiper is working. At that
time, the wiper stops working until the
window is closed again.
If the back window is not fully closed, the
back window wiper, washer and defogger
will not work. (See “Back window wiper
and washer” on page 138 and “Back window and outside rear view mirror defoggers” on page 139 in Section 1- 5.)
’05 4Runner_U (L/O 0411)
If the battery is disconnected or run
down, the power back window may not
operate automatically and the jam protection function will not function correctly after you reconnect, replace or recharge the
battery. In any of these cases, you should
normalize the power back window with the
power back window switch.
To normalize the power back window:
1. Push the “” (down) switch and lower
the window halfway.
2. Push the “” (up) switch until the window closes and hold the switch for a
second.
Make sure that the window opens and
closes automatically. If the power back
window cannot be operated properly, have
it checked by your Toyota dealer.
OPERATING FROM INSIDE
The ignition key must be in the “ON” position.
Normal operation: To open or close the
back window, quickly push and release the
“” (down) or “” (up) switch.
Automatic operation: To open or close
the back window, push and hold the “ ”
(down) or “” (up) switch. The window
will fully open or close. To stop the window partway, push the switch on either
the “” (down) or “” (up) side briefly.
Key off operation: If both front doors are
closed, it works for 43 seconds even after
the ignition switch is turned off. It stops
working when either front door is opened.
Jam protection function: During automatic closing operation or key off closing operation, the window stops and opens half
way if something gets caught between the
window and window frame.
If the window receives a strong impact,
this function may work even if nothing is
caught.
CAUTION
Never try jamming any part of your
body to activate the jam protection
function intentionally.
The jam protection function may
not work if something gets caught
just before the window is fully
closed.
29
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
If you push in the window lock switch on
the driver’s door, the back window cannot
be operated.
’05 4Runner_U (L/O 0411)
OPERATING FROM OUTSIDE
The back window can be opened and
closed with the key operation in the back
door keyhole.
To open: Turn the key fully counterclockwise and hold it.
After the door is unlocked, the window
begins to open. To stop the window partway, release the key.
To close: Turn the key fully clockwise and
hold it.
After the door is locked, the window begins to close. To stop the window partway,
release the key.
This door key linked function can be disabled. For details, contact your Toyota
dealer.
Jam protection function: During closing
operation, the window stops and opens
half way if something gets caught between
the window and window frame.
If the window receives a strong impact,
this function may work even if nothing is
caught.
30
2005 4RUNNER from Nov. ’04 P rod. (OM35841U)
Loading...