Toyota 4runner 2001 Owner's Manual

’01 4Runner_U (L/O 0008)

Foreword

Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering and quality construction of each vehicle we build.

This Owner’s Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupants follow the instructions carefully. Doing so will help you enjoy many years of safe and trouble−free motoring. For important information about this manual and your Toyota, read the following pages carefully.

When it comes to service, remember that your Toyota dealer knows your vehicle best and is interested in your complete satisfaction. He will provide quality maintenance and any other assistance you may require.

Please leave this Owner’s Manual in this vehicle at the time of resale. The next owner will need this information also.

All information and specifications in this manual are current at the time of printing. However, because of Toyota’s policy of continual product improvement, we reserve the right to make changes at any time without notice.

Please note that this manual applies to all models and explains all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle.

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

Important information about this manual

Safety and vehicle damage warnings

Throughout this manual, you will see safety and vehicle damage warnings. You must follow these warnings carefully to avoid possible injury or damage.

The types of warnings, what they look like, and how they are used in this manual are explained as follows:

CAUTION

This is a warning against something which may cause injury to people if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk to yourself and other people.

NOTICE

This is a warning against something which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your vehicle and its equipment.

Safety symbol

When you see the safety symbol shown above, it means: “Do not...”; “Do not do this”; or “Do not let this happen”.

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

Important information about your Toyota

New vehicle warranty

Your new vehicle is covered by the following Toyota limited warranties:

D New vehicle warranty D Emission control systems warranty D Others

For further information, please refer to the “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement”.

Your responsibility for maintenance

It is the owner’s responsibility to make sure that the specified maintenance is performed. Section 6 gives details of these maintenance requirements. Also included in Section 6 is general maintenance. For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

Accessories, spare parts and

modification of your Toyota

A wide variety of non−genuine spare parts and accessories for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.

This vehicle should not be modified with non−genuine Toyota products. Modification with non−genuine Toyota products could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from the modification may not be covered under warranty.

iii

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

Spark ignition system of your

Toyota

The spark ignition system in your Toyota meets all requirements of the Canadian Interference−Causing Equipment Standard.

Installation of a mobile

two−way radio system

As the installation of a mobile two−way radio system in your vehicle could affect electronic systems such as multiport fuel injection system/sequential multiport fuel injection system, traction control system (two−wheel drive models)/active traction control system (four−wheel drive models), vehicle skid control system, cruise control system, anti−lock brake system, electronic throttle control system, SRS airbag system and seat belt pretensioner system, be sure to check with your Toyota dealer for precautionary measures or special instructions regarding installation.

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

Scrapping of your Toyota

The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals. If the vehicle is scrapped with the airbags and pretensioners left as they are, it may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you dispose of your vehicle.

On−pavement and off−road

driving tips

This vehicle belongs to the utility vehicle class. Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle will handle and maneuver differently from an ordinary passenger car because it is designed for off−road use also. In addition, this vehicle has a higher ground clearance and center of gravity than that of an ordinary passenger car. This vehicle design feature causes this type of vehicle to be more likely to rollover. Failure to operate this vehicle correctly may result in loss of control, accidents or vehicle rollover causing death or serious injury. Be sure to read “Off−road vehicle precautions” in Section 2 and “Off−road driving precautions” in Section 3.

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

SECTION 1− 1

OPERATION OF INSTRUMENTS AND CONTROLS

Overview of instruments and controls

Instrument panel overview 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Instrument cluster overview 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Indicator symbols on the instrum ent panel 6. . . . . . . . . . . . . . . . . . . . . . .

2001 4RUNNER (OM35768U)

Instrument panel overview

’01 4Runner_U (L/O 0008)

1. Side vents

2. Tilt steering lock release lever

3. Instrument cluster

4. Center vents

5. Garage door opener

6. Garage door opener box or auxiliary box

7. Electric moon roof switch

8. Personal lights

9. Glove box

10. Power door lock switches

11. Power window switches

12. Automatic transmission selector lever

13. Parking brake lever

14. Ashtray

15. Cup holders

16. Front drive control lever

17. Lower vent

18. Hood lock release lever

19. Fuel filler door opener

20. Window lock switch

21. Power rear view mirror control switches (with power windows)

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

1. Seat heater switch (for passenger)

2. Headlight and turn signal switch, and front fog light switch

3. Wiper and washer switches

4. Back window and rear view mirror defoggers switch

5. Driving pattern selector button

6. Clock

7. Emergency flasher switch

8. Power back window switch

9. Theft deterrent system/Engine immobiliser system indicator light

10. Front passenger’s seat belt reminder light

11. Air conditioning controls

12. Car audio

13. Ashtray

14. Power outlets

15. Cigarette lighter

16. “OUT/T” (outside temperature) button

17. Ignition switch

18. Cruise control switch

19. Center differential lock switch

20. Instrument panel light control knob

21. Power rear view mirror control switch (without power windows)

2001 4RUNNER (OM35768U)

22. Traction control off switch

23. Seat heater switch (for driver) or Power back window lock switch

’01 4Runner_U (L/O 0008)

2001 4RUNNER (OM35768U)

Instrument cluster overview

’01 4Runner_U (L/O 0008)

1. Service reminder indicators and indicator lights

2. Engine coolant temperature gauge

3. Tachometer

4. Speedometer

5. Odometer and two trip meters

6. Fuel gauge

2001 4RUNNER (OM35768U)

7. Trip m eter res et knob

Indicator symbols on the instrument panel

∗

Brake system warning light

Driver’s seat belt reminder light

∗

’01 4Runner_U (L/O 0008)

Vehicle skid control system and traction control system (two−wheel drive models) or active traction control system (four−wheel drive models) warning light

∗

Front passenger’s seat belt reminder light

∗

Discharge warning light

Low oil pressure warning light

Malfunction indicator lamp

Low fuel level warning light

∗

Open door warning light

SRS warning light

Unengaged “Park” warning light

Automatic transmission fluid temperature warning light

Low windshield washer fluid level warning

∗

light

∗

Turn signal indicator lights

∗

Anti−lock brake system warning light

Headlight high beam indicator light

2001 4RUNNER (OM35768U)

Overdrive−off indicator light

Automatic transmission indicator lights

Driving pattern (“PWR” mode) indicator light

Four−wheel drive and center differential lock indicator lights

Slip indicator light

∗

Traction control system off indicator light

(two−wheel drive models)

’01 4Runner_U (L/O 0008)

Vehicle skid control system off indicator light (four−wheel drive models)

∗

Cruise control indicator light

∗

: For details, see “Service reminder indicators and warning

buzzers” in Section 1−5.

∗

: If this light flashes, see “Cruise control” in Section 1−6.

2001 4RUNNER (OM35768U)

∗

’01 4Runner_U (L/O 0008)

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

SECTION 1− 2

OPERATION OF INSTRUMENTS AND CONTROLS

Keys and Doors

Keys 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine immobiliser system 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Side doors 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power windows 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power back window 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Back door 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hood 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Theft deterrent system 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel tank cap 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electric moon roof 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

Keys (without engine immobiliser system)

Your vehicle is supplied with two kinds of keys.

1. Master key—This key works in every lock.

2. Sub key—This key will not work in the glove box.

To protect things locked in the glove box when you have your vehicle parked, leave the sub key with the attendant.

Since the doors can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.

KEY NUMBER PLATE Your key number is shown on the plate.

Keep the plate in a safe place such as your wallet, not in the vehicle.

If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number.

We recommend you to write down the key number and keep it in safe place.

Keys (with engine immobiliser system)

Your vehicle is supplied with the two kinds of keys.

1. Master key (black)—This key works in every lock. Your Toyota dealer will need it to make you a new key with built−in transponder chip.

2. Sub key (gray)—This key does not work in the glove box.

A transponder chip for engine immobiliser system has been filled in the head of the master and sub keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys. If you make your own duplicate key, you will not be able to cancel the system or start the engine.

2001 4RUNNER (OM35768U)

To protect things locked in the glove box when you have your vehicle parked, leave the sub key with the attendant.

Since the side doors can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.

For information on use of the wireless remote control key, see “Side doors” in this section.

’01 4Runner_U (L/O 0008)

NOTICE

When using a key containing a transponder chip, observe the following precautions:

z When starting the engine, do not

use the key with a key ring resting on the key grip and do not press the key ring against the key grip. Otherwise the engine may not start, or may stop soon after it starts.

2001 4RUNNER (OM35768U)

z When starting the engine, do not

use the key with other transponder keys around (including keys of other vehicles) and do not press other key plates against the key grip. Otherwise the engine may not start, or may stop soon after it starts. If this happens, remove the key once and then insert it again after taking off other transponder keys (including keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine.

z Do not bend the key grip.

’01 4Runner_U (L/O 0008)

z Do not cover the key grip with any

material that cuts off electromagnetic waves.

z Do not knock the key hard against

other objects.

z Do not leave the key exposed to

high temperatures for a long period, such as on the dashboard and hood under the direct sunlight.

z Do not put the key in water or

wash it in an ultrasonic washer.

z Do not use the key with electromag-

netic materials.

KEY NUMBER PLATE Your key number is shown on the plate.

Keep the plate in a safe place such as your wallet, not in the vehicle.

If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number.

We recommend you to write down the key number and keep it in safe place.

2001 4RUNNER (OM35768U)

Engine immobiliser system

The engine immobiliser system is a theft prevention system. When you insert the key in the ignition switch, the transponder chip in the key’s head transmits an electronic code to the vehicle. The engine will start, only when the electronic code in the chip corresponds to the registered ID code for the vehicle.

’01 4Runner_U (L/O 0008)

The system is automatically set when the key is removed from the ignition switch. The indicator light will start flashing to show the system is set.

If either of the following indicator conditions occurs, contact your Toyota dealer.

D The indicator light stays on except

when the theft deterrent system is setting or activating. (See “Theft deterrent system”.)

D The indicator light does not start flash-

ing when the key is removed from the ignition switch.

D The indicator light flashes unsteady.

Inserting the registered key in the ignition switch automatically cancels the system, which enables the engine to start. The indicator light will go off.

For your Toyota dealer to make you a new key with built−in transponder chip, your dealer will need your key number and master key. However, there is a limit to the number of additional keys your Toyota dealer can make for you.

If you make your own duplicate key, you will not be able to cancel the system or start the engine.

NOTICE

Do not modify, remove or disassemble the engine immobiliser system. If any unauthorized changes or modifications are made, the proper operation of the system cannot be guaranteed.

2001 4RUNNER (OM35768U)

For vehicles sold in U.S.A.

’01 4Runner_U (L/O 0008)

Side doors

For vehicles sold in Canada

FCC ID: MOZ RI−4BTY MADE IN JAPAN

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with RSS−210 of Industry Canada. Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn

it.

To lock: Turn the key forward. To unlock: Turn the key backward.

Vehicles with power door lock system— All the doors lock and unlock simultaneously with either front door. In the driver’s door lock, turning the key once will unlock the driver’s door and twice in succession will unlock all the doors simultaneously.

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

LOCKING AND UNLOCKING WITH INSIDE LOCK BUTTON

Move the lock button.

To lock: Push the button downward. To unlock: Pull the button upward.

Closing the door with the lock button pushed in will also lock the door. Be careful not to lock your keys in the vehicle.

Vehicles with power door lock system—The front doors cannot be locked if you leave the key in the ignition switch.

Driver’s side

Front passenger ’s side

Driver’s side

Front passenger ’s side

With power windows

2001 4RUNNER (OM35768U)

Without power windows

’01 4Runner_U (L/O 0008)

LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH

Push the switch.

To lock: Push the switch on the front side. To unlock: Push the switch on the rear side.

All the doors lock or unlock simultaneously.

When the front side doors are locked from the outside or locked with the wireless remote control transmitter, the power door lock switch will not work until either front door is unlocked with the key, lock knob, or wireless remote control transmitter.

CAUTION

Before driving, be sure that the doors are closed and locked, especially when small children are in the vehicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the vehicle during an accident. It also helps prevent the doors from being opened unintentionally.

REAR DOOR CHILD−PROTECTORS Move the lock lever to the “LOCK”

position as shown on the label.

This feature allows you to lock a rear door so it can be opened from the outside only, not from inside. We recommend using this feature whenever small children are in the vehicle.

2001 4RUNNER (OM35768U)

—Wireless remote control

Locking operation

’01 4Runner_U (L/O 0008)

Your vehicle has a wireless remote control system that can lock or unlock all the side doors and back door from a distance within approximately 1 m (3 ft.) of the vehicle.

LOCKING AND UNLOCKING THE SIDE DOORS AND BACK DOOR

To lock and unlock all the side doors and back door, push the switches slowly and securely.

To lock: Push the “LOCK” switch. All the side doors and back door are locked simultaneously. At this time one beep will be heard, and the parking lights and tail lights flash once.

Check to see that all the side doors and back door are securely locked.

If any of the side doors or back door is not securely closed, locking cannot be performed by the “LOCK” switch and a beep will sound continuously for 10 seconds. However, if the key is in the ignition, a beep will not sound.

To stop the buzzer, close all the doors securely or push the “UNLOCK” switch.

To unlock: Push the “UNLOCK” switch once to unlock the driver’s door alone. Pushing the switch twice within 3 seconds unlocks all the side doors and back door simultaneously. Each time the “UNLOCK” switch is pushed, two beeps will be heard, and the parking lights and tail lights flash twice.

You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the side doors and back door will be automatically locked again.

If the “LOCK” or “UNLOCK” switch is kept pressed in, the locking or unlocking operation is not repeated. Release the button and then push again.

The volume of beep sound can be changed. Contact your Toyota dealer for details if you require it.

Unlocking operation

2001 4RUNNER (OM35768U)

OPENING THE BACK WINDOW To open the back window, push the

back window open switch of the transmitter for about 1 second. The window will fully open.

At this time, you can hear a beep. If the ignition switch is in the “ON” posi-

tion, the back window cannot be opened by the back window open switch.

To open the back window with the master key, see “Power back window” in this section.

The volume of beep sound can be changed. Contact your Toyota dealer for details if you require it.

’01 4Runner_U (L/O 0008)

“PANIC” SWITCH Pushing the “PANIC” switch blows the

horn intermittently and flashes the headlights and tail lights.

The “PANIC” switch is used to deter vehicle theft when you witness anyone attempting to break into or damage your vehic le.

The alarm will last for one minute. To stop alarm midway, push the “PANIC” or “UNLOCK” switch, or unlock any side door or back door with key. You can also stop the alarm by turning the ignition key from “LOCK” to the “ON” position.

The “PANIC” mode does not work when the ignition key is in the “ON” position.

WIRELESS REMOTE CONTROL TRANSMITTER

The wireless remote control transmitter is an electronic component. Observe the following instructions in order not to cause damage to the transmitter.

D Do not leave the transmitter on places

where the temperature becomes high such as on the dashboard.

D Do not disassemble it. D Avoid knocking it hard against other

objects or dropping it.

D Avoid putting it in water.

You can use up to 4 wireless remote control transmitters for the same vehicle. Contact your Toyota dealer for detailed information.

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

If the wireless remote control transmitter does not actuate the doors or operate from a normal distance:

D Check for closeness to a radio trans-

mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.

D The battery may have been consumed.

Check the battery in the transmitter. To replace the battery, see following “REPLACING THE BATTERY”.

If you lose your wireless remote control transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an accident.

For vehicles sold in U.S.A.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

D Reorient or relocate the receiving an-

tenna.

D Increase the separation between the

equipment and receiver.

D Connect the equipment into an outlet

on a circuit different from that to which the receiver is connected.

D Consult the dealer or an experienced

radio / TV technician for help.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For vehicles sold in Canada

Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

REPLACING THE BATTERY

For replacement, use a lithium battery CR2016 and a special screwdriver.

CAUTION

Special care should be taken that small children do not swallow the removed battery or components.

NOTICE

When replacing the transmitter battery, be careful not to lose the components.

Replace the battery by the following procedures :

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

1. Using a coin or equivalent, open the transmitter case.

2. Remove the discharged transmitter battery.

2001 4RUNNER (OM35768U)

3. Put new transmitter battery with positive (+) side up.

Close the transmitter case securely.

NOTICE

z Make sure the positive side and

negative side of the transmitter battery should be faced correctly.

z Be careful that dust or oils do not

adhere to the transmitter case.

z Close the transmitter case securely.

After replacing battery, check that the transmitter operates properly. If the transmitter still does not operate properly, contact your Toyota dealer.

If you lose your transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an accident. (See “If you lose your wireless remote control transmitter” in Section 4.)

Power windows

Driver’s door switches

’01 4Runner_U (L/O 0008)

Window lock switch

The windows can be operated with the switch on each side door.

The power windows work when the ignition switch is in the “ON” position.

Key off operation: If both front side doors are closed, they work for 43 seconds even after the ignition switch is turned off. They stop working when either front side door is opened.

OPERATING THE DRIVER’S AND FRONT PASSENGER’S WINDOWS

Use the switches on the driver’s door and front passenger’s door.

Normal operation: The window moves as

long as you hold the switch. To open: Lightly push down the switch.

To close: Lightly pull up the switch. If you push in the window lock switch on

the driver’s door, the front passengers’ window cannot be operated.

Front passenger’s door switch

2001 4RUNNER (OM35768U)

Driver’s door switches

Front passenger’s door switch

’01 4Runner_U (L/O 0008)

Automatic operation: Push the switch

completely down or pull it completely up, and then release it. The window will fully open or close. To stop the window partway, lightly move the switch in the opposite direction and then release it.

If you push in the window lock switch on the driver’s door, the front passengers’ window cannot be operated.

Jam protection function: During automatic closing operation, the window stops and opens half way if something gets caught between the window and window frame.

If the window receives a strong impact, this function may work even if nothing is caught.

CAUTION

D Never try jamming any part of your

body to make the jam protection function work intentionally.

D The jam protection function may

not work if something gets caught just before the window is fully closed.

Window lock switch

Driver’s door sw itches

OPERATING THE REAR PASSENGERS’ WINDOWS

Use the switch on each rear passenger’s door or the switches on the driver’s door that control each rear passenger’s windows.

The window moves as long as you hold the switch.

To open: Push down the switch. To close: Pull up the switch.

If you push in the window lock switch on the driver’s door, the rear passengers’ windows cannot be operated.

2001 4RUNNER (OM35768U)

Rear passengers’ door switches

’01 4Runner_U (L/O 0008)

CAUTION

To avoid serious personal injury, you must do the following.

D Always make sure the heads, hands

and other parts of the bodies of all occupants are kept completely inside the vehicle before you close the power windows. If someone’s neck, head or hands gets caught in a closing window, it could result in a serious injury. When anyone closes the power windows, make sure that he/she operates the windows safely.

D When small children are in the ve-

hicle, never let them use the power window switches without supervision. Use the window lock switch to prevent them from making unexpected use of the switches.

D Never leave small children alone in

the vehicle, especially with the ignition key still inserted. They could use the power window switches and get trapped in a window. Unattended children can be involved in serious accidents.

Power back window

The back window can be operated with the inner switch on the center console or outer switch on the back door.

OPERATING FROM INSIDE

The ignition key must be in the “ON” position.

The back window moves as long as you hold the inner switch.

To open: Push the switch on the “ side. To close: Push the switch on the “

side.

”

2001 4RUNNER (OM35768U)

+ 271 hidden pages