Total Scooter Rental User Manual

1121 South 21st Ave Suite A Hollywood, FL 33020 | Phone: [phone]

Toll free [phone] | www.totalmobilityservices.org

Scooter Rental User Guide

Getting Started

Make sure the scooter is turned off, charger is unplugged from the wall as well as the scooter. Pivot the armrest in upward motion to make

getting on and off the scooter easier. You can also swivel the seat around by engaging the lever located under the seat. Make sure swivel seat is in

lock mode prior to mounting and dismounting.

Operating Your Scooter

Turn the key clockwise to power on your scooter. Set the speed to your desired comfort by turning the dial counter-clockwise to go slower and

clockwise to go faster. Grasp the throttle control lever with your right/left hand and the scooter will move forward. The more you engage the

throttle lever the faster the speed of the scooter will go. Each scooter has a maximum programed speed. Pull the tiller handle bars to your left to

steer your scooter to the left. Pull the tiller handle bars to your right to steer your scooter to the right. Bring the tiller handle bars to the center

position to drive straight forward.

Stopping

Release the throttle lever and the scooter electromagnetic brakes will automatically engage and your scooter will come to a stop.

Reversing

Grasp the throttle lever with your left hand and the scooter will go in reverse. Reverse speed is programed to be slower than forward speed mode.

Always make sure you check behind you to make sure path is clear and safe before engaging in reverse mode.

Dismounting

Bring your scooter to a complete stop and power off and remove the key from the key switch. Carefully, slowly and safely get out of the seat and

utilize swivel seat option if needed.

Charging Your Scooter

The scooter needs to be charged every night. Make sure your scooter is powered off and the key removed before charging. Once the scooter is

powered off, connect the 3 prong end into the scooter first and then the electrical end into the wall outlet. Make sure the connection to each side

of the charger is secure, and pushed in all the way to ensure proper contact between charger and battery is being made. These steps are important

to follow or charging failure may occur. Do not leave your scooter charging for more than a 10 hour cycle. When travelling avoid completely

draining your batteries and it is suggested to conserve two power bars prior to charging scooter each evening for next day use.

*** In case of rain***

If it begins to rain while on the scooter please immediately proceed to a covered area. If a covered area cannot be reached quickly. Immediately

cover the top of the unit with a bag or poncho and proceed to seek cover. The electric components inside the scooter will malfunction if they

are exposed to the rain/liquids/sand and it will cause unit to seize up until ALL components are dried out and necessary damaged parts are

replaced.

Troubleshooting Guide

***Make sure the charger is unplugged from both the scooter and from the wall. Take the key completely out before

starting the steps below***

1. My scooter powers on but is not moving and beeping: Turn the power off and check the manual brake lever. Ensure the lever is pulled

toward the locked position. Now you may turn the key to power up your scooter and wait for the lights to illuminate fully BEFORE you try to press

the throttle to move.

2. My scooter has no power and is not moving: Check the circuit breaker located on the battery case itself. Press the clear silicone bubble to

flip fuse switch back on. Now you may turn the key to power up your scooter and wait for the lights to illuminate fully BEFORE you try to press the

throttle to move.

3. My scooters not moving: Ensure that battery case is properly seated in its position. Sometimes going over a large bump or during assembly

and disassembly when transporting can cause the battery case to shift from it’s secure connection. This can easily be fixed by grasping onto the

carry handle located on the top of the battery case. Lift the case in an upwards motion and snap back into proper position. A snapping noise

indicates the battery case is secure and stable power connection has been made. Now you may turn the key to power up your scooter and wait for

the lights to illuminate fully BEFORE you try to press the throttle to move.

4. My scooters not moving: If you did not have power returned after completing steps 1-3. You may be experiencing protect mode. This

happens when components of the scooter are overworked. Make sure you do not carry luggage or extra weight on the scooter and avoid steep

inclines past manufacture safety suggestion. The scooter protects itself from overheating by shutting down. To fix, follow steps 1-3 and allow the

scooter time to cool down in a cool well-ventilated area for about 20 mins. Now you may turn the key to power up your scooter and wait for the

lights to illuminate fully BEFORE you try to press the throttle to move. If power still does not return call the number on bottom of page for

technical assistance.

All above steps must be followed in the suggested order. Should you have any problems please call us right away so we may

provide customer care assistance.

1121 South 21st Ave Suite A Hollywood, FL 33020 | Phone: [phone] |Toll free [phone] | www.totalmobilityservices.org