Toshiba VTD1552 User Guide

MODEL VTD1552 USER GUIDE

DIGITAL VIDEO

Region /

ALL

discs only

Combination 15” Flat TV and

5Q40401A Cov-In 3/25/05, 10:43 AM1

DVD Video Player

TELETEXT

WARNING

To prevent fire or shock hazard, do not expose this equipment to rain or moisture.

MAINS SUPPLY

This unit is designed to operate from AC 230V~240V 50Hz household mains supply.

This unit is supplied with an approved 13 amp (BS 1363) fused mains plug. When replacing the fuse always use a 5 amp (BS 1362) approved type. Never use this plug if the fuse cover is missing. To obtain a replacement fuse cover contact your store. If the mains sockets in your home differ or are not suitable for the type of plug supplied, then the plug should be cut from the mains lead and a suitable type fitted.

WARNING: If the mains plug is cut from the mains lead of this appliance the plug must be destroyed. A mains plug with bared wires is hazardous if engaged in a mains output line socket.

You must use a 13 amp plug (BS 1363) and fit a 5 amp fuse (BS 1362). If any other type of plug is used a 5 amp fuse must be fitted, either in the plug, adaptor or at the distribution board.

WIRING INSTRUCTIONS

The wires in the mains lead are coloured in accordance with the following code:

As the colours of the wires in the mains lead of the appliance may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red. No connection is to be made to the Earth (E,

CAUTION:

THIS UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE PLAYER CORRECTLY AS INSTRUCTED.

THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE UNIT.

BLUE — NEUTRAL BROWN — LIVE

) terminal.

CLASS 1 LASER PRODUCT

WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

NOTES ON MOISTURE CONDENSATION

Moisture condensation damages the unit. Please read the following carefully.

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the head drum or the optical pick-up lens inside this unit, one of the most crucial internal parts of the unit.

Moisture condensation occurs during the following cases.

When you bring the unit directly from a cold place to a warm place. When you use the unit in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit. In summer, when you use the unit in a hot and humid place just after you move the unit from an air conditioned room. When you use the unit in a humid place.

Do not use the unit when moisture condensation may occur.

If you use the unit in such a situation, it may damage discs and internal parts. Remove the disc, connect the power cord of the unit to the wall outlet, turn on the unit, and leave it for two or three hours. After two or three hours, the unit will have warmed up and evaporated any moisture. Keep the unit connected to the wall outlet and moisture condensation will seldom occur.

5Q40401A Cov-In 3/25/05, 10:43 AM2

PRECAUTIONS

SOME DOS AND DON'TS ON THE SAFE USE OF EQUIPMENT

This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. So, please read the points below for your own safety.

**************

DO read the operating instructions before you attempt to use the equipment. DO ensure that all electrical connections (including the mains plug, extension leads and inter-

connections between the pieces of equipment) are properly made and in accordance with the manufacturer's instructions. Switch off and withdraw the mains plug before making or changing connections. DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment. DO be careful with glass panels or doors on equipment.

**************

DON'T remove any fixed cover as this may expose dangerous voltages. DON'T obstruct the ventilation openings of the equipment with items such as newspapers,

tablecloths, curtains, etc. Overheating will cause damage and shorten the life of the equipment. DON'T allow electrical equipment to be exposed to dripping or splashing, or objects filled with liquids, such as vases, to be placed on the equipment. DON'T place hot objects or naked flame sources such as lighted candles or nightlights on, or close to equipment. High temperatures can melt plastic and lead to fires.

DON'T use makeshift stands. DON'T listen to headphones at high volume, as such use can permanently damage your hear-

ing. DON'T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a stand-by mode. Switch off using the switch on the equipment and make sure that your family know how to do this. Special arrangements may need to be made for infirm or handicapped people. DON'T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way -switch off, withdraw the mains plug and consult your dealer.

ABOVE ALL

---NEVER let anyone especially children push anything into holes, slots or any other opening in the case - this could result in a fatal electrical shock;

---NEVER guess or take chances with electrical equipment of any kind

---it is better to be safe than sorry! *************

5Q40401A P01-07 3/25/05, 10:43 AM1

FEATURES

• Auto Set up (Channel)

• Auto Channel Memory

• TELETEXT Function

• On-Screen Programming

• Picture Control Adjustments

• Auto Power Shut Off

DVD Player

• Digital Audio Jack (Coaxial)

• Multi-Language

CONTENTS

PREPARATION

PRECAUTIONS ......................................................... 1

LOCATION OF CONTROLS ...................................... 3

REMOTE CONTROL ................................................. 4

AERIAL CONNECTIONS ........................................... 6

CONNECTION TO OTHER EQUIPMENT ................. 7

TV OPERATION

AUTOMATIC TUNING SYSTEM ............................... 9

PRESETTING THE CHANNELS ............................. 10

TV OPERATIONS .................................................... 13

CONVENIENT FUNCTIONS ................................... 14

PICTURE ADJUSTMENTS ...................................... 15

AV COLOUR ADJUSTING ...................................... 16

RECEPTION OF INTERFERENCE ......................... 17

TELETEXT ............................................................... 18

• Multi-Angle

• Repeat Playback

• Memory/Random Playback

• Zoom

• Video Aspect Ratio

• Parental Control

• Digital output for Dolby Digital (AC-3) and DTS

• Playback of DVD, Video-CD, SVCD, Audio-CD and MP3/WMA/JPEG-CD

•PAL & NTSC DVDs playback

• A-B Repeat playback

ADVANCED FUNCTION OF DVD SECTION

SETTING THE ASPECT RATIO OF TV SCREEN .. 34

SETTING ON SCREEN DISPLAY ........................... 34

DYNAMIC RANGE CONTROL ................................ 35

PARENTAL CONTROL SETTING ........................... 36

TO CHANGE THE PARENTAL LEVEL ................... 37

TEMPORARY DISABLING OF RATING LEVEL BY

DVD DISC ................................................................ 38

SETTING MENU LANGUAGE ................................. 39

SETTING SUBTITLE LANGUAGE .......................... 40

SETTING AUDIO SOUNDTRACK LANGUAGE ...... 41

ADDITIONAL INFORMATION

LANGUAGE CODE LIST ......................................... 42

BEFORE REQUESTING SERVICE ......................... 43

SPECIFICATIONS ................................................... 44

DISC PLAYBACK OPERATION

DISC ........................................................................ 20

PREPARATION ....................................................... 21

STATUS DISPLAY OF DISC ................................... 21

PLAYBACK PROCEDURE ...................................... 22

SPECIAL PLAYBACK .............................................. 23

MP3/WMA/JPEG PLAYBACK ................................. 24

SETTING THE JPEG INTERVAL ............................ 26

SETTING THE SELECT FILES ............................... 27

ZOOMING ................................................................ 28

CHANGING ANGLES .............................................. 28

LOCATING DESIRED SCENE ................................ 28

REPEAT PLAYBACK ............................................... 29

PROGRAM PLAYBACK/RANDOM PLAYBACK

(VCD/CD) ................................................................. 30

MARKING DESIRED SCENES ............................... 31

CHANGING SOUNDTRACK LANGUAGE/

SUBTITLES ............................................................. 32

KARAOKE PLAYBACK ............................................ 33

TITLE SELECTION .................................................. 33

DVD MENU .............................................................. 33

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents

and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation or other rights owners and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation or other rights owners. Reverse engineering or disassembly is prohibited.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby

Laboratories.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

5Q40401A P01-07 3/25/05, 10:43 AM2

Front

LOCATION OF CONTROLS

Disc tray

Rear

Remote sensor

Main Power Switch

OPEN/CLOSE button

STANDBY Indicator

VOLUME

CHANNEL

Indoor Aerial Holder

buttons

/ buttons

Phones socket

VIDEO/AUDIO IN (L/R) jacks (AV2)

FWD SKIP button

REV (Reverse) SKIP button

STOP button

PLAY button

Mains Lead to AC outlet

5Q40401A P01-07 3/25/05, 10:43 AM3

RF IN jack

21 pin SCART (AV1)

COAXIAL DIGITAL AUDIO OUT jack

REMOTE CONTROL

Page

TV/DVD Select to operate TV or DVD 8,13,21

OPEN/CLOSE Open or Close the tray 22,24,25,38

TEXT/MIX/TV Select teletext 18,19

ON/STANDBY Power on/off 9,13,21,22

0-9 Direct channel selection of TV 13,14

Input setting 25,28,30

Enter a security code 36,37

DISPLAY Display TV or DVD operation status 14,21

0/AV Scart Input or Front AV input 8,14

MUTE Mute 14

JUMP Locating desired scene 28

DVD MENU Select menu of a DVD disc 25,33

TOP MENU Select title of a DVD disc 25,33

VOL +/– Volume Up/Down 13,14

ANGLE Change playback angle of a DVD disc 28

MARKER Index for DVD 31

CH RTN Switch between present/last channel 14

ZOOM Zoom (for DVD playback) 28

SUBTITLE Set Subtitle of a DVD disc 32

AUDIO Change sound track language of DVD 32,33

CH/PAGE +/– Select channel of the TV 13,14

Utilize the teletext 19

▲/▼/B/A Cursor buttons

ENTER

MENU SETUP

CANCEL

RETURN Remove DVD set up menu 26,27,34~41

PLAYPlayback 22~25,29,30,33,38

STOP Stop 22,24,25

SKIP / Skip chapter to forward or reverse direction 23,25

HOLD Hold 18

F/T/B F/T/B 19

SEARCH8/9 Reverse search or Forward search playback 23

REVEAL Reveal 19

SUB PAGE Sub page 19

SLOW / Slow motion playback 23

PAUSE Still picture 23

PLAY MODE Select playback mode 29,30

Four Coloured buttons

REPEAT A-B Repeat playback between A and B (DVD/CD) 29

Enter information in the menu/Select option in the menu

Display menu of setup 10~12,15,16,26,27,34~37,39~41

Cancel input data in the setting mode

Access the Teletext 18

14,15,28,30,31,36,37

5Q40401A P01-07 3/25/05, 10:43 AM4

BATTERY INSTALLATION

REMOTE CONTROL

Open the battery compartment cover in the direction of the arrow.

Install two “AAA/R03/UM-4” (penlight size) batteries, paying attention to the polarity diagram in the battery compartment.

Replace the cover.

BATTERY CAUTIONS

Use two “AAA/R03/UM-4” size batteries for the remote control transmitter.

•

The batteries may last approximately one year depending on how much the remote control is used. For best

•

performance it is recommended batteries be replaced on a yearly basis, or when remote operation becomes erratic. Do not mix old and new batteries.

•

Weak batteries can leak and severely damage the remote control transmitter. Always remove batteries as

•

soon as they become weak. Dispose of batteries in a designated disposal area.

•

Do not throw batteries into a fire.

EFFECTIVE DISTANCE OF THE REMOTE CONTROL TRANSMITTER

NOTES: • When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the

remote sensor, the remote operation may be unstable.

• When there is an obstacle between the unit and the transmitter, the remote control transmitter may not

operate.

5Q40401A P01-07 3/25/05, 10:43 AM5

AERIAL CONNECTIONS

Connect an indoor or outdoor aerial to the aerial socket at the rear panel as shown below. For all aerial circuit problems, please consult your local dealer.

(A)

(B)

Aerial socket

Mains lead

(A)

INDOOR AERIAL

A loop aerial is supplied with the unit. Insert the aerial holder into the mounting hole on the back cabinet until it locks into place. Insert the aerial adaptor (supplied) to the aerial socket. Adjust the angle of the loop aerial to receive the best possible picture.

(B) EXTERNAL AERIAL

The type of aerial required depends on the position of your home, it's distance from the transmitter and local interference. If you do not have an aerial and you are uncertain of what to buy, you should seek the advice of a local aerial contractor.

5Q40401A P01-07 3/25/05, 10:43 AM6

CONNECTION TO OTHER EQUIPMENT

The exact arrangement you use to interconnect various video and audio components to the unit is dependent on the model and features of each component. Check the Owner's Manual provided with each component for the location of video and audio inputs and outputs.

Using an AV Amplifier with built-in digital surround

If you are using an Amplifier with a built-in digital surround sound decoder (such as Dolby Digital / DTS / MPEG / etc.), you can connect it as shown below.

Rear of unit

Front Speaker (Right)

Coaxial Digital Audio Output

Coaxial digital cable (not supplied)

To Coaxial Digital Audio Input

Front

Speaker

(Left)

This unit

Subwoofer

Centre Speaker

Surround

AV Amplifier with built-in digital surround decoder as listed above

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of

Speaker (Left)

Surround Speaker (Right)

Laboratories. Confidential unpublished works.

“DTS” and “DTS Digital Out” are trademarks of Digital Theatre Systems, Inc.

NOTES:

• When you make the connections above, make sure that the power of all units is switched off at the mains.

• Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.

• When playing DTS encoded material, the sound will only be available through the Digital Audio Output Socket.

Dolby

5Q40401A P01-07 3/25/05, 10:43 AM7

CONNECTION TO OTHER EQUIPMENT

Input Selection

If you connect the unit to a VCR, camcorder or games console, you can select this input by pressing 0/AV.

Press TV/DVD to select TV mode and then press 0/AV repeatedly to select AV1 or AV2.

AV1(Scart socket)

AV2(Front AV input)

AV1

TV-program

1. To connect the unit to a VCR Press 0/AV to select AV1 to use the TV as a monitor.

Rear of unit

To Scart socket

of VCR

Scart cable (not supplied)

Scart socket

2. To connect the unit to a TV Game

The unit can also be used as a display device for many video games. However, due to the wide variety of different types of signal generated by these devices and subsequent hook-up variations required, they have not all been included in the suggested connection diagrams. Press 0/AV to select AV2 to use the TV as a monitor. You'll need to consult each component's Owner's Manual for additional information.

Front of unit

VIDEO IN

To Audio/Video OUT

Audio/Video cord (not supplied)

3. To connect the unit to a camcorder

Connect the camcorder to the unit as shown. Press 0/AV to select AV2 to use the TV as a monitor.

Camcorder

To Audio/Video OUT

Audio/Video cord (not supplied)

VIDEO IN

4. To connect the unit to another TV set (ie. a widescreen set) (see P.34)

Connect the unit and another TV set with a Scart cable. Press the AV button on another TV to monitor the input from the Scart cable.

AUDIO IN (R)

AUDIO IN (L)

Front of unit

AUDIO IN (R)

AUDIO IN (L)

5Q40401A P08-17 3/25/05, 11:22 AM8

AUTOMATIC TUNING SYSTEM

Your television has an Automatic Tuning System which makes tuning in your television easy. System scans the entire reception range in your area and automatically stores all available channels of suitable signal strength in the correct order e.g. BBC1 will tune into channel 1, BBC2 will tune into channel 2, etc.

ONLY WHEN YOU TURN ON THIS UNIT FOR THE FIRST TIME, THE AUTOMATIC TUNING PROCESS WILL BE AVAILABLE.

Press the Main POWER ( ) switch on the unit.

Then press ON/STANDBY on the remote control.

Press ENTER.

Your unit will now automatically tune in all available channels.

When the programme on the screen stops changing and the sound comes on, the tuning process is complete.

NOTE: If you use the supplied loop aerial, weak channels may not be stored automatically.

You will need to tune these manually.

This Automatic tuning

CONNECT AERIAL TO TV

THEN PRESS ENTER TO

START AUTO TUNING

AUTO TUNING

5Q40401A P08-17 3/25/05, 10:44 AM9

PRESETTING THE CHANNELS

Once you have connected up this unit, you will need to tune in the channels in order to watch TV stations. There are two ways that you can do this:

- Automatic tuning The stations will be preset in the order that

they appear when the automatic tuning is activated.

- Manual tuning In this mode the TV searches until a picture appears. If it is a station that you want to keep, you can choose which channel preset you want to store it on. You repeat this procedure for each station until you have stored all the desired stations.

AUTOMATIC TUNING

Press TV/DVD to select TV mode.

Press MENU.

Press or to select the CHANNEL SETUP mode, then press ENTER.

Press or to select the

AUTO mode, then press ENTER.

CHANNEL SETUP

PICTURE AV COLOUR PAL

▲

▼

PRESS:

/ ENTER / MENU

CHANNEL SETUP

MANUAL

AUTO

CH ALLOCATION

▲

▼

/ ENTER / MENU

NOTES:

• If you want to skip any channels, refer to

page 14.

• When the unit is in the AV mode, you can’t preset the channels.

All available channels in your area

are automatically scanned and stored in the memory of the unit. When the programme on the

 

screen stops changing and the sound comes on, the tuning process is complete.

Press MENU twice.

The unit will return to normal TV screen.

• The automatic tuning will not necessarily store the channels in the correct order (BBC1 on CH 1 etc.). If you want to change the order of the stored channels, please see page 12.

5Q40401A P08-17 3/25/05, 10:44 AM10

PRESETTING THE CHANNELS

MANUAL TUNING

How to tune a station to channel 10 position.

Press MENU.

Press CHANNEL SETUP mode, then press ENTER.

Press or to select the

MANUAL mode, then press ENTER.

or to select the

CHANNEL SETUP

PICTURE AV COLOUR PAL

▲

▼

PRESS:

/ ENTER / MENU

CHANNEL SETUP

MANUAL

AUTO

CH ALLOCATION

▲

▼

/ ENTER / MENU

Press or until the picture

CH position

appears on screen. If this is not your desired channel, press or until your desired channel

appears. If you need to make the picture

clearer, use

or (FINE

SEARCH: BA/ F.TUNE: CD

TUNING). Then press ENTER.

Press or to select channel

position No.10, then press

Searching direction

Tuning segment bar

ENTER.

PRESS:▲/▼/ENTER/MENU

Repeat steps 3 through 4 until all the required channels

have been stored.

When all desired channels have been set in your required

position, press MENU three times to return to normal TV screen.

CH 1

CH 10

5Q40401A P08-17 3/25/05, 10:44 AM11

PRESETTING THE CHANNELS

TO CHANGE THE CHANNELS

EXAMPLE: Changing of channel position from CH2 and CH5.

Press MENU.

Press or to select the CHANNEL SETUP mode, then press ENTER.

Press or to select the CH

ALLOCATION mode, then press ENTER.

Press or to select the channel position No. (broadcasting) which you want to change. Then press ENTER.

CHANNEL SETUP

PICTURE AV COLOUR PAL

▲

▼

PRESS:

CH ALLOCATION CH 1

/ ENTER / MENU

CHANNEL SETUP

MANUAL AUTO

CH ALLOCATION

▲

▼

/ ENTER / MENU

CH 2

Press or to select the

channel allocation No. that you want to change to.

Press ENTER. The numbers of

the stations are changed. Repeat steps 3 - 4 to change the order of other channels. Then press MENU three times to return to normal TV screen.

Before setting

▲

▼

PRESS:

CH ALLOCATION

PRESS:

CH ALLOCATION CH 2

PRESS:

/ ENTER / MENU

▲

▼

/ ENTER / MENU

▲

▼

/ ENTER / MENU

CH 2

CH 5

+0 #

5Q40401A P08-17 3/25/05, 10:44 AM12

After setting

TV OPERATIONS

After completing the connection and presetting the channels, follow these steps for viewing.

Press Power ( ) on the front panel of the unit. Then press

ON/STANDBY on the remote control (STANDBY indication will goes off). Press TV/DVD to select TV mode.

Direct Channel Selection buttons (0-9)

Press Direct Channel Selection buttons on the remote control.

1-9 CH: Press your required number only. 10-80 CH: Press the two digits in accordance to the channel

numbers required.

CH + / – Press CH + or – on the remote control.

The VOLUME can be adjusted

by pressing the VOL + or – on the remote control.

VOLUME 32

+0 '

NOTE:

On screen display will disappear after 4 seconds.

Automatic Power Shut Off

If a station being viewed stops broadcasting for about 15 minutes, the unit will automatically shut itself off and go into standby mode.

5Q40401A P08-17 3/25/05, 10:44 AM13

+ 34 hidden pages