Toshiba ST-7000 User Manual

TEC POS Terminal
ST-7000 SERIES

Owner's Manual

CE Compliance (for EU only)
This product complies with the requirements of EMC and Low Voltage Directives including their amendments.
WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Warnung Dies ist ein Klasse A Produkt. In einer örtlichen Umgebung kann dieses Gerät Funkstörungen verursachen.
ATTENTION Ce produit est de classe A. Dans un environnement domestique, il peut causer des interférences radio. Auquel cas, l’utilisateur sera amené à prendre les mesures adéquates.
Atención Este es un producto de la clase A. En ambientes domésticos éste producto puede causar radio interferencias en cuyo caso el usuario deberá tomar las medldas oportunas.
VERWITTIGING Dit is een klasse A produkt. Het gebruik hiervan kan radio interferenties veroorzaken die de gebruiker ertoe kunnen dwigen sommige maatregelen te moeten treffen.
Avviso Questo è un apparecchio di Classe A. In un ambiente residenziale questo apparecchio quò provocare radiodisturbi. In questo caso può essere richiesto all’utilizzatore di prendere misure adeguate.
Schallemission: unter 70dB (A) nach DIN 45635 (ISO7779)
FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at this own expense.
Changes or modifications not expressly approved by manufacturer for compliance could void the user’s authority to operate the equipment.
Microsoft and Windows are registered trademarks of Microsoft Corporation. Celeron is a registered trademark of Intel Corporation.
Copyright © 2004 by TOSHIBA TEC CORPORATION All Rights Reserved 570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN
Safety Summary
6DIHW\6XPPDU\
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified using the procedures described in this manual, turn off the power, unplug the machine, then contact your authorized TOSHIBA TEC representative for assistance.
0HDQLQJVRI(DFK6\PERO
This symbol indicates warning items (including cautions). Specific warning contents are drawn inside the (The symbol on the left indicates a general caution.)
This symbol indicates prohibited actions (prohibited items). Specific prohibited contents are drawn inside or near the (The symbol on the left indicates “no disassembling”.)
This symbol indicates actions which must be performed. Specific instructions are drawn inside or near the symbol. (The symbol on the left indicates “disconnect the power cord plug from the outlet”.)
symbol.
symbol.
EO1-12029
:$51,1*
3URKLELWHG
3URKLELWHG
3URKLELWHG
Do not plug in or unplug the power cord plug with wet hands as this may cause
electric shock
If the machines share the same outlet with any other electrical appliances that consume large amounts of power, the voltage will fluctuate widely each time these appliances operate. Be sure to provide an exclusive outlet for the machine as this may cause
.
shock
Do not insert or drop metal, flammable or other foreign objects into the machines through the ventilation slits, as this may cause
.
shock
machines are improperly handled contrary to this indication.
$Q\ RWKHU WKDQ WKH VSHFLILHG $& YROWDJH LV SURKLELWHG
.
Do not use voltages other than the voltage (AC) specified on the rating plate, as thi s may cause or
electric shock
Do not place metal objects or water-filled containers such as flower vases, flower pots or mugs, etc. on top of the machines. If metal objects or spilled liquid enter the machines, this may cause or
electric shock
Do not scratch, damage or modify the power cords. Also, do not place heavy objects on, pull on, or excessively bend the cords, as this may cause
fire
or
fire
electric
or
electric
3URKLELWHG
3URKLELWHG
fire
or
.
.
electric shock
fire
fire
.
This indicates that there is the risk of death or serious injury if the
'LVFRQQHFW WKH SOXJ
If the machines are dropped or their cabinets damaged, first turn off the power switches and disconnect the p ower cord plugs from the outlet, and then contact your authorized TOSHIBA TEC representative for assistance. Continued use of the machine in that condition may cause
.
shock
fire
or
electric
'LVFRQQHFW WKH SOXJ
Continued use of the machines in an abnormal condition such as when the machines are producing smoke or strange smells may cause
or
fire
electric shock
cases, immediately turn off the power switches and disconnect the power cord plugs from the outlet. Then, contact your au thorized TOSHIBA TEC representative for assistance.
. In these
(i)
Safety Summary
EO1-12029
'LVFRQQHFW WKH SOXJ
&RQQHFW D JURXQGLQJ ZLUH
&$87,21
If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorized TOSHIBA TEC representative for assistance. Continued use of the machine in that condition may cause
electric shock
Ensure that the equipment is properly grounded. Extension cables should also be grounded.
Fire
or occur on improperly grounded equipment.
.
electric shock
This indicates that there is the risk of personal the machines are improperly handled contrary to this indication.
fire
could
or
'LVFRQQHFW WKH SOXJ
1R GLVDVVHPEOLQJ
When unplugging the power cords, be sure to hold and pull on the plug portion. Pulling on the cord portion may cut or expose the internal wires
fire
and cause
electric shock
or
Do not remove covers, repair or modify the machine by yourself. You may be voltage, very hot parts or sharp edges inside the machin e. Unauthorized modification is prohibited.
injured
Injury
damage
or
to objects if
by high
3UHFDXWLRQV
The following precautions will help to ensure that this machine will continue to function correctly.
Try to avoid locations that have the following adverse conditions:
* Temperatures out of the specification * Direct sunlight * High humidity * Shared power source * Excessive vibration * Dust/Gas
Do not subject the machine to sudden shocks.
Do not press the keys too hard. Keys will operate correctly if they are touched lightly.
Clean the cover and keyboard, etc. by wiping with a dry cloth or a cloth soaked with detergent and
wrung out thoroughly. Never use thinner or other volatile solvent for cleaning.
At the end of the day, turn the power OFF, then clean and inspect the exterior of the machine.
Try to avoid using this equipment on the same power supply as high voltage equipment or equipment
likely to cause mains interference.
USE ONLY TOSHIBA TEC SPECIFIED consumables.
DO NOT STORE the consumables where they might be exposed to direct sunlight, high temperatures, high
humidity, dust, or gas.
When moving the machine, take hold of the drawer and lift the machine.
Do not place heavy objects on top of the machines, as these items may become unbalanced and fall
causing injury.
Do not block the ventilation slits of the machines, as this will cause heat to build up inside the
machines and may cause fire.
Do not lean against the machine. It may fall on you and could cause injury.
Place the machine on a stable and level surface.
.
5HTXHVW 5HJDUGLQJ 0DLQWHQDQFH
Utilize our maintenance services.
After purchasing the machine, contact your authorized TOSHIBA TEC representative for assistance
once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the machines and may cause a fire or a malfunction. Cleaning is particularly effective before humid rainy seasons.
Our preventive maintenance service performs the periodic checks and other work required to maintain
the quality and performance of the machines, preventing accidents beforehand.
For details, please consult your authorized TOSHIBA TEC representative for assistance.
Using insecticides and other chemicals
Do not expose the machines to insecticides or other volatile solvents. This will cause the cabinet or
other parts to deteriorate or cause the paint to peel.
(ii)
EO1-12029

TABLE OF CONTENTS

Page
1. INTRODUCTION----------------------------------------------------------------------------------------- 1- 1
1.1 Accessories ------------------------------------------------------------------------------------------------1- 1
2. APPEARANCE------------------------------------------------------------------------------------------- 2- 1
3. CONNECTORS ------------------------------------------------------------------------------------------ 3- 1
4. INSTALLATION PROCEDURE ---------------------------------------------------------------------4- 1
4.1 Environmen t fo r In stallation --------------------------------------------------------------------------4- 1
4.2 Attaching the Cable Cover----------------------------------------------------------------------------4- 1
5. HOW TO LOCK/UNLOCK THE FRONT PANEL----------------------------------------------- 5- 1
6. GENERAL MAINTENANCE-------------------------------------------------------------------------- 6- 1
6.1 Cleaning-----------------------------------------------------------------------------------------------------6- 1
7. TROUBLESHOOTING--------------------------------------------------------------------------------- 7- 1
8. SPECIFICATIONS -------------------------------------------------------------------------------------- 8- 1
8.1 Basic Specifications--------------------------------------------------------------------------------------8- 1
8.2 Options------------------------------------------------------------------------------------------------------8- 2
CAUTION!
1. This manual may not be copied in whole or in part without pr ior written permission of TOSHIBA TEC.
2. The contents of this manual may be changed without notif ication.
3. Please refer to your local Authorised Service represent at ive with regard to any queries you may have in this manual.
1. INTRODUCTION
EO1-12029
1.1 Accessories
1. INTRODUCTION
Thank you for choosing t he TEC POS Terminal. This POS Terminal contains all the high per formance register function necessary f or a POS Terminal and enables the user oriented system configuration. By adopting a high-speed CPU, Memory with large capacity, this POS Terminal flexibly accepts the modification corresponding to t he future system environment as the user expects. This manual describes the functions and handling of this POS terminal and should be read carefully to help gain maximum performance and life from your POS terminal. For most queries please refer t o this manual and keep it safe for future ref er ence.
1.1 Accessories
Confirm that all the following accessories are contained in the carton. If any accessories are m issing or damaged, contact your TOSHIBA TEC service representative.
Cable Cover (1 pc.) Front Panel Key (2 pcs.) Cable Clamp (2 pcs.) (Used to secure the USB Cable, etc. to the POS terminal)
Ferrite Core (2 pcs.) Ferrite Core (1 pc.) Ferrite Core (2 pcs.) (For the Drawer Cable) (For the Audio Cable) (For the TFT Monitor Cable)
Bind Unify Screw Double Sems Screw N0.6x4.5 (8 pcs.) M-3x8 (2 pcs.) (Used to secure the HDDs) (Used to secure the Cable Clamp)
NOTE: The power cord is not included in the carton. Please prepare it separately from a local dealer.
1- 1
2. AP P EAR AN CE
2. APPEARANCE
2. APPEARANCE
< Front View >
Power LED
HDD LED
POWER LED
HDD LED
Reset Switch
Volume
Power Switch
USB5 Connector
(1) Power Switch
This is the switch to turn the power of t he POS terminal ON or OFF. The Power LED is illuminated when turning the power on.
Front Panel Lock
Front Panel
Cover Catch
CD-RW Drive (Option)
EO1-12029
(2) Power LED (Green)
This is the LED to indicate the power ON/O FF status of the POS terminal. Green LED is illuminated when turning the power ON.
(3) HDD LED (Yellow)
This is the LED for a model with the Har d Disk Drive installed. Yellow LED is illuminated during the access to the Hard Disk Drive.
(4) Front Panel Lock
This is the lock of the front panel. To lock the front panel, insert the front panel key to the front panel lock, then turn it clockwise. T o unlock the front panel, turn the front panel key counterclockwise.
(5) Reset Switch Pressing this switch when the POS terminal hangs up resets the unit .
CAUTION!
Do not press the Reset Switch unnecessarily. Doing so m ay cause an er r or .
(6) Volume Used to adjust the internal speaker volume.
When it is t ur ned t o left, the sound volume turns down. When it is t ur ned t o r ight, the sound volume turns up.
(7) USB5 Connector Connector for the USB (Universal Serial Bus) interface conform ing to USB V2.0/1.1. A USB
Mouse, USB keyboard, etc. can be connected to this connector.
2- 1
3. CONNECTORS
3. CONNECTORS
Powered USB USB0 USB1 USB2 USB3 (12V-1) (12V-2) (12V-3) (24V)
COM5 COM1
COM2
Not Used
EO1-12029
3. CONNECTORS
COM6 (Option)*
Line-out Mic-in
PCI Slot
COM3
LPT1
COM4
VGA
DVI-D, LVDS (Option)
DRW1, DRW2
Connector Description
AC Inlet A connector for the AC inlet AC Outlet A connector to supply AC power to the CRT.
AC power is output in synchronization with the ON/OFF status of the POS terminal.
P24V DC Outlet A terminal of a DC24V line to which the power cable of the Receipt/Journal printer is
connected.
PS/2 (Mouse, Keyboard) Mini-DIN 6-pin female type connector
Connector for the PS/2 type mouse, Connector for the PS/2 type keyboard USB0, 1, 2, 3 (Powered USB) USB4 (General 5V USB)
LAN Modular type connector for the 10BASE-T/100BASE-TX LAN interface DRW1, DRW2 A 24V type drawer is connectable. DVI-D, LVDS Expandable LCD interface (Option) VGA A 15-pin VGA connector to the CRT COM1,2 D-sub 9-pin male type connector (without power supply)
COM3, 4, 5, 6 D-sub 9-pin female type connector (with +5V, +12V output)
LPT1 D-sub 25-pin female connector
Line-out Used for connecting an external speaker via the stereo mini jack terminal Mic-in Used for connecting a monophonic microphone via the mono mini jack terminal
*: COM6 is installed on the PCI slot.
Connector for the USB (Universal Serial Bus) interface USB V2.0/1.1 and UHCI
(conforming to Universal Hub Controller Interface V2.0/1.1)
NOTE: USB functions may not be supported depending on the Operating System.
USB0 to USB3 are powered USB sockets, which are 3 ports of 12V USB (USB0 to
USB2) and 1 port of 24V USB (USB3). The lower part of these sockets can be used
as general 5V USB connectors.
A slot scanner, modem, serial Interface type scale, EFT, etc. are connectable.
A line display unit or RS-232C type hand scanner is connectable.
NOTES: 1 COM4 cannot be used when the touch panel TFT is connected to the POS terminal.
2. COM6 is available only when the optional kit is installed.
Printer, etc. having a Centronics interface or equivalent are connectable.
USB4
LAN
24V DC Outlet
Not used (5VB)
PS/2 (Mouse) PS/2 (Keyboard)
AC Inlet
AC Outlet
3- 1
4. INSTALLATION PROCEDURE
4.1 Environment for Installation
EO1-12029
4. INSTALLATION PROCEDURE
4.1 Environment for Installation
1. Provide a space of minimum 80 mm to the left, right, front, rear, and top of the main unit for proper cooling. (The main unit has air vents on the front, rear, right and left, and a fan. Spaces should be provided to prevent the air vents in the main unit fr om being closed and the air flow from being obstructed.)
2. Attaching the cable cover:
The cable cover must be attached to protect the interface cables or connectors. Be sure to turn off
the power before connecting or disconnecting t he cables.
3. Notes on installing the display unit on the top of the enclosure:
When installing t he display unit on t he t op of the enclosure, the following conditions must be
satisfied. (Except for t he st andar d display unit)
1) Display unit weighing 12Kg or under
2) The base of the display unit has no proj ect ions t hat might damage the enclosure.
3) The base of the display unit does not pr ot r ude beyond the st eel plate at the top of the main
unit.
4.2 Attaching the Cable Cover
1. Insert the guides on both sides of the cable cover into the slits provided on the POS ter m inal, then slide down the cable cover to the bottom.
NOTE: Be sure to attach the cable cover for protecting the cables.
Cable Cover
2. When detaching the cable cover, hold both sides by hands, then pull it up.
Guide
Slit
4- 1
5. HOW TO LOCK/UNLOCK THE FRONT PANEL
11
232
3
11
232
3
5. HOW TO LOCK/UNLOCK THE FRONT PANEL
EO1-12029
5. HOW TO LOCK/UNLOCK THE FRONT PANEL
<< How to unlock the front panel >>
Front Panel
1. Insert the front panel key into the front panel lock, and turn it counterclockwise to unlock the front panel.
2. Push the upper center of the front panel until it clicks .
3. Gently open the front panel holding it by hand.
<< How to lock the front panel >>
Front Panel
1. Gently close the front panel.
2. Push the upper center of the front panel until it clicks .
3. Turn the front panel key clockwise to lock the front panel.
Front Panel Lock
Front Panel Lock
5- 1
6. GENERAL MAINTENANCE
6. GENERAL MAINTENANCE
EO1-12029
6.1 Cleaning
6.1 Cleaning
WARNING!
1. Be sure to disconnect the power cord prior to per f orming any maintenance.
2. Do not pour water directly on the POS Term inal or wipe it with a soaked cloth, as this may cause fire, electric shock, or machine failure.
CAUTION! Never use an organic solvent like thinners or benzene for cleaning. Using such solvents may
discolor the covers.
To help retain the high q uality and performance of your POS Terminal, it should be cleaned regular ly. The greater the usage on the POS Terminal, the more frequent the cleaning. ( i. e. low usage = weekly: high usage = daily)
• Cleaning the Covers
Wipe the covers with a soft dry cloth or soft cloth slightly moistened with mild detergent. After using
detergent for cleaning , be sure to wipe it off with a slightly moistened cloth.
6- 1
7. TROUBLESHOOTING
7. TROUBLESHOOTING
7. TROUBLESHOOTING
WARNING!
If you cannot solve a problem with the following solutions, do not attempt to r epair it by your self. Turn the power off, unplug the POS Terminal, then contact the nearest TOSHIBA TEC service representative for assistance.
Symptom Check point Solution
The power does not turn on.
Is the power cord plugged in correctly?
Is the power supplied to the AC outlet?
Has the circuit breaker blown?
Plug in correctly.
If it is not a power failur e,
check for the power supply to the AC outlet with another electric appliance. When the power is not supplied, contact your nearest power company.
Check the circuit breaker.
EO1-12029
7- 1
8. SPECIFICATIONS
8.1 Basic Specif i c ations
EO1-12029
8. SPECIFICATIONS

8.1 Basic Specifications

Item Description
Input voltage AC 100V-240V +10%, -10% 50/60Hz 4.6A-2.2A DC output voltage DC24V +5%, -5% AC output voltage AC 100V-240V +10%, -10% 50/60Hz 2.0A-1. 0A Operating temperatur e 5°C to 35°C Relative humidity 10% to 80%RH (no condensation) Dimensions 315 mm (W ) x 466 mm (D) x 112.5 mm (including the rubber feed and
cable cover) Weig ht 9.5 Kg (without 2 HDDs, CD, UPS batt er y, PCI , and packing materials) Power cord A power cord is not included in this product. Please use one complied
with each country’s safety standard. For details, please contact t he
nearest TOSHIBA TEC ser vice repr esent at ive. CPU Intel Celeron 2.0 GHz with 128 KB secondary cache
(up to Pentium4 2.8 GHz) BIOS ROM 1MB Flash ROM RAM
Interface RS-232C x 5, Parallel x 1, P-USB x 4, USB x 2, Drawer x 2 (24V type),
Display interface RGB x 1 channel (on-board, standard) Expansion LCD Interface DVI-D x 1 / LVDS x 1 (option) UPS Available when the UPS (option) and driver are installed. Hard Disk Drive (HDD) Max. 2 units of 3.5-inch HDD (option) can be connected. CD-RW dr ive 1 drive (local purchase is required),
LAN interface 10 BASE-T, 100 BASE-TX ( Wake on LAN suppor t) Sound generator AC97 interface, LINE OUT x 1, MIC IN x 1 Floppy Disk Drive (FDD) USB interface type (local purchase is required.) Support OS Windows 2000, Windows XP, DOS
Capacity Standard 256MB (Max. 2GB)
Max. 1GB/slot can be equipped.
Type DDR SDRAM PC2100/2700, 2.5V unbuffered t ype, ECC/ non ECC 184-
pin DDR SDRAM DIMM connector, 2 slots installed
PS/2 x 2, PCI (Half size slot) x 2, +24V OUT (DIN 3- pin) x 1
CD connection kit required ( opt ion)
8- 1
8. SPECIFICATIONS
8.2 Options
Option name Type Description
EO1-12029
8.2 Options
Drawer unit
Line display unit LIUST-51-1AF-QM 20 characters x 2 lines dot display Printer Unit
POS keyboard unit
Scanner HS-530-RS-24B-09-QM Touch scanner (RS-232C interface type) TFT monitor TFTST-56T-3V-QM 12.1-inch TFT monitor equipped with the touch panel
Operation Unit LKBST-65 TT11-QM 12.1-inch TFT monitor equipped with the 40 keys keyboard
Mounting kit
DRWST-51A-4MV-QM DRWST-51A-8MV-QM
DRWST-56-EMV-QM 24V-drive flip top drawer
Drawer type
TRST-56-P-1W-QM Parallel interface single thermal printer for 80 mm wide paper
TRST-56-S-1W-QM Serial interface single thermal printer for 80 mm wide paper
TRJST-52-3S-QM Serial interface 2-station thermal printer for 58-mm wide paper TRJST-52-3P-QM Parallel interface 2-station thermal printer for 58-mm wide paper PKBST-50-3-QM 81 keys POS keyboard with PS/2 interface
KIT-7000-DISP1-QM Interface board kit for attaching the DVI-D (digital signal) or LVDS
KIT-7000-COM-QM COM6 connector kit for attaching the PCI slot KIT-7000-CD-QM Mounting kit for attaching the CD drive
Type Bill holder Coin tray Mini coin case CDC Remarks 4MV-QM 5 5 No Yes With media slot 8MV-QM 4 6 1 Yes With media slot EMV-QM 5 8 No Yes With media slot
24V-drive standard drawer Size and Weight: 460(W) x 400(D) x 115(H) mm, 10Kg Money Case Type: MC4,8
Size and Weight: 460(W) x 170(D) x 100(H) mm, 6Kg Money Case Type: EURO case
Cabinet color: FW-2
Cabinet color: FW-2
(with VGA board)
(The magnetic card reader is provided as an option.)
(analog signal)display
8- 2
PRINTED IN JAPAN
E
EO1-12029A
Loading...