Toshiba SD-V392SU User Manual

Download

Page 1

Introduction

DIGITAL VIDEO

DVD VIDEO PLAYER & VIDEO CASSETTE RECORDER

SD-V392SU

OWNER’S MANUAL

Connections

Basic setup

Playback

(VCR)

Recording

(VCR)

Other functions

(VCR)

Basic playback

(DVD)

Advanced

playback

(DVD)

This device does not tape-record copy protected DVD Video Discs.

Function setup

(DVD)

Others

2C53301C (E)COV 21/4/04, 11:081

Page 2

Introduction

IMPORTANT SAFEGUARDS

The lightning flash with arrowhead symbol, within an

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE P ARTS INSIDE. REFER SERVICING T O QUALIFIED SER VICE PERSONNEL.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to rain

or moisture.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN

EXTENSION CORD, RECEPT ACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSER TED TO PREVENT BLADE EXPOSURE.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Changes or modifications not expressly approved by the partly responsible for compliance with the FCC Rules could void the user's authority to operate this equipment.

CAUTION: THIS DIGIT AL VIDEO PLAYER EMPLOYS A LASER SYSTEM.

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONT ACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.

USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIA TION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT ST ARE INT O BEAM.

Location of the required Marking

The rating sheet and the safety caution are on the rear of the unit.

CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J.

2C53301C (E)p02-13 21/4/04, 11:082

Page 3

IMPORTANT SAFEGUARDS

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning the exterior cabinet only.

6. ATTACHMENTS

The manufacturer of this unit does not make any recommendations for attachments, as they may cause hazards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

8. ACCESSORIES

Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury, and serious damage to the unit.

8A. An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

9. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation, to ensure reliable operation of the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and/or the manufacturer’s instructions have been adhered to.

10. POWER SOURCE

This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions.

11. GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Instead of the polarized alternating-current line plug, your unit may be equipped with a 3-wire grounding-type plug (a plug having a third (grounding) pin). This plug will only fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.Do not defeat the safety purpose of the grounding-type plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

PORTABLE CART WARNING

(symbol provided by RETAC)

S3125A

Introduction

2C53301C (E)p02-13 21/4/04, 11:083

Page 4

Introduction

IMPORTANT SAFEGUARDS

13. LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. For example: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions. Adjust only those controls

that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal

operation. e. If the unit has been dropped or the cabinet has been damaged. f . When the unit exhibits a distinct change in performance, this indicates a need for service.

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

21. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

22. DISC TRAY

Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.

23. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.

2C53301C (E)p02-13 21/4/04, 11:084

Page 5

IMPORTANT SAFEGUARDS / Power source

24. LASER BEAM

Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.

25. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.

26. NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

GROUND CLAMP

ANTENNA DISCHARGE UNIT

ELECTRIC SERVICE

EQUIPMENT

NEC-NATIONAL ELECTRICAL CODE S2898A

(NEC SECTION 810-20) GROUNDING CONDUCTORS

(NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING

ELECTRODE SYSTEM (NEC ART 250, PART H)

Introduction

Power source

AC Outlet

Wider Hole and Blade

Polarized AC Cord Plug (One blade is wider than the other.)

2C53301C (E)p02-13 21/4/04, 11:085

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet.

Notes:

Never connect the AC line cord plug to other than the specified

• voltage (120V 60Hz). Use the attached power cord only. If the polarized AC cord does not fit into a non-polarized AC

• outlet, do not attempt to file or cut the blade. It is the user’s responsibility to have an electrician replace the obsolete outlet. If you cause a static discharge when touching the unit and the

• unit fails to function, simply unplug the unit from the AC outlet and plug it back in. The unit should return to normal operation.

Page 6

Introduction

Precautions

Notes on handling

When shipping the DVD/VCR, the original shipping carton and packing materials come in handy. For maximum protection, repack the unit as it was originally packed at the factory. Do not use volatile liquids, such as insect spray, near the DVD/VCR. Do not leave rubber or plastic products to contact the DVD/VCR for a prolonged period. They will leave marks on the finish. The top and rear panels of the DVD/VCR may become warm after a long period of use. This is not a malfunction. When the DVD/VCR is not in use, be sure to remove the disc and the video cassette turn off the power. If you do not use the DVD/VCR for a long period, the unit may not function properly in the future. Turn on and use the DVD/VCR occasionally.

Notes on locating

Place the DVD/VCR on a level surface. Do not use it on a shaky or unstable surface such as a wobbling table or inclined stand. The loaded disc or the video tape may become dis-aligned and damage the DVD/ VCR. When you place this DVD/VCR near a TV, radio, or VCR, the playback picture may become poor and the sound may be distorted. In this case, place the DVD/ VCR away from the TV, radio, or VCR.

Notes on moisture condensation

Moisture condensation damages the DVD/VCR. Please read the following carefully.

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the head drum or the optical pick-up lens inside this unit, one of the most crucial internal parts of the DVD/VCR.

Moisture condensation occurs during the following cases.

When you bring the DVD/VCR directly from a cold place to a warm place. When you use the DVD/VCR in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit. In summer, when you use the DVD/VCR in a hot and humid place just after you move the unit from an air conditioned room. When you use the DVD/VCR in a humid place.

Tape

Head drum

It’s too

warm!

Notes on cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, soak the cloth in a weak detergent solution, wring well and wipe. Use a dry cloth to wipe it dry. Do not use any type of solvent, such as thinner and benzine, as they may damage the surface of the DVD/VCR. If you use a chemical saturated cloth to clean the unit, follow that product’s instructions.

To obtain a clear picture

The DVD/VCR is a high technology, precision device. If the video head, the head drum, the optical pick-up lens or disc drive parts are dirty or worn down, the picture quality will deteriorate. To obtain a clear picture, we recommend regular inspection and maintenance (cleaning or parts replacement) every 1,000 hours of use depending on the operating environment. For details, contact your nearest dealer.

Do not use the DVD/VCR when moisture condensation may occur.

If you use the DVD/VCR in such a situation, it may damage discs and internal parts. Remove the disc or the video tape, connect the power cord of the DVD/ VCR to the wall outlet, turn on the DVD/VCR, and leave it for two or three hours. After two or three hours, the DVD/VCR will have warmed up and evaporated any moisture. Keep the DVD/VCR connected to the wall outlet and moisture condensation will seldom occur.

Wait!

Wall outlet

2C53301C (E)p02-13 21/4/04, 11:086

Page 7

Notes on discs

On handling discs

Do not touch the playback side of the disc.

Playback side

Do not attach paper or tape to discs.

On cleaning discs

Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.

Structure of disc contents

Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs are divided into tracks.

DVD video disc

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3

Video CD/Audio CD

Track 1 Track 2 Track 3 Track 4 Track 5

Each title, chapter or track is assigned a number, which is called “title number”, “chapter number” or “track number” respectively. There may be discs that do not have these numbers.

Introduction

If you cannot wipe off the dust with a soft cloth, wipe the disc lightly with a slightly moistened soft cloth and finish with a dry cloth. Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight or near heat sources. Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier. Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

Notes on copyright

It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, and rent copyrighted material without permission.

This device does not tape-record copy protected DVD Video Discs. The device is not to be used for copying copyrighted content without the express written permission of the copyright owner. Obtaining such permission is the sole responsibility of the user.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

2C53301C (E)p02-13 21/4/04, 11:087

Page 8

Introduction

Notes on discs (continued)

About this owner’s manual

This owner’s manual explains the basic instructions of this DVD/VCR. Some DVD video discs are produced in a manner that allows specific or limited operation during playback. As such, the DVD/VCR may not respond to all operating commands. This is not a defect in the DVD/ VCR. Refer to instruction notes of discs.

” may appear on the TV screen during operation.

“

” means that the operation is not permitted by the

A “ DVD/VCR or the disc. For example, sometimes it is unable to stop the playback of copyright message of the disc when the STOP (3) button is pressed. Alternatively, the “

” may

also indicate that the feature is not available for the disc.

Notes on region numbers

The region number of this DVD/VCR is 1. If region numbers, which stand for their playable area, are printed

ALL

on your DVD video disc and you do not find

, disc playback will not be allowed by the player. (In this case, the DVD/VCR will display a message on-screen.)

On Video CDs

This DVD/VCR supports Video CDs equipped with the PBC (Version 2.0) function. (PBC is the abbreviation of Playback Control.) You can enjoy two playback variations depending on types of discs.

• Video CD not equipped with PBC function

(Version 1.1)

Sound and movie can be played on this DVD/VCR in

the same way as an audio CD.

• Video CD equipped with PBC function

(Version 2.0)

In addition to operation of a Video CD not equipped with the PBC function, you can enjoy playback of interactive software with search function by using the menu displayed on the TV screen (Menu Playback). Some of the functions described in this owner’s manual may not work with some discs.

Playable discs

This DVD/VCR can play the following discs.

Disc Mark

DVD video discs

Video CDs

Audio CDs

The following discs are also available.

Some of these discs may be incompatible.

DIGITAL VIDEO

DVD-R/RW discs of DVD video format CD-R/CD-RW discs of CD-DA, Video CD, SVCD, MP3, WMA or JPEG format Kodak Picture CD and FUJICOLOR CD format

Contents

Audio Video

(moving

pictures)

Audio Video

(moving

pictures)

Audio

Disc Size

12 cm

8 cm

12 cm

8 cm

12 cm

8 cm

(CD

single)

• You cannot play discs other than those listed above.

• You cannot play discs of DVD-RAM, DVD-ROM, Photo CD, etc., or non standardized discs even if they may be labeled as above.

• Some CD-R/RWs can not be played back depending on the recording conditions.

• This DVD/VCR uses the NTSC color system, and cannot play DVD video discs recorded in any other color system (PAL, SECAM, etc.).

Maximum

playback time

Approx. 4 hours

(single sided disc)

Approx. 8 hours

(double sided disc)

Approx. 80 minutes

(single sided disc)

Approx. 160 minutes

(double sided disc)

Approx. 74 minutes

Approx. 20 minutes

Approx. 74 minutes

Approx. 20 minutes

2C53301C (E)p02-13 21/4/04, 11:098

Page 9

Contents

Introduction

IMPORTANT SAFEGUARDS ..........................2

Power source ...................................................5

Precautions ......................................................6

Notes on discs..................................................7

Contents...........................................................9

Identification of controls .................................10

Connections

Antenna connections......................................14

CATV (CABLE TV) connections.....................16

Connecting to a TV ........................................18

Connecting to optional equipment..................20

Basic setup

Setting the video channel............................... 22

Setting the language ...................................... 23

Clock setting................................................... 24

Tuner setting .................................................. 27

Playback (VCR)

Loading and unloading a cassette tape ......... 29

Cassette tape playback.................................. 30

Special playback ............................................ 31

Convenience function..................................... 32

Recording (VCR)

Recording a TV program................................ 34

One-touch Timer Recording (OTR)................ 36

Timer recording .............................................. 37

Basic playback (DVD)

Playing a disc ................................................. 42

Advanced playback (DVD)

MP3/WMA/JPEG playback ............................ 45

Zooming ......................................................... 50

Locating desired scene .................................. 50

Marking desired scenes ................................. 51

Repeat playback ............................................ 52

A-B Repeat playback ..................................... 52

Program playback (CD).................................. 53

Random playback (CD).................................. 53

Changing angles ............................................ 54

Title selection ................................................. 54

DVD menu...................................................... 54

Function setup (DVD)

Changing soundtrack language ..................... 55

Setting surround sound .................................. 55

Setting subtitles.............................................. 56

Karaoke playback........................................... 56

E.B.L. (Enhanced Black Level) ...................... 57

Setting the aspect ratio of TV screen ............. 58

Setting on screen display ............................... 59

Status display of disc ..................................... 59

Dynamic Range Control ................................. 60

Parental control setting .................................. 61

To change the parental level.......................... 62

Temporary disabling of rating level by DVD disc ..

Setting OSD language ................................... 64

Setting language ............................................ 65

Selecting PROGRESSIVE scan..................... 66

Introduction

Other functions (VCR)

Stereo recording and playback ...................... 39

Second Audio Program (SAP)........................ 39

Duplicating a video tape................................. 40

Recording a DVD/CD disc.............................. 41

2C53301C (E)p02-13 21/4/04, 11:099

Others

Language code list ......................................... 67

Troubleshooting ............................................. 68

Specifications ................................................. 69

Limited warranty............................................. 70

Page 10

Introduction

Identification of controls

See the page in for details.

Front panel

EJECT button

ON/STANDBY

button

AUDIO (L/R)/VIDEO IN (LINE IN 2) jacks

Rear panel

Cassette loading slot

REC button

CHANNEL M/? buttons

VCR indicator

Remote sensor

Display window

VCR/DVD mode selector button

DVD indicator

STOP button

PLAY button

OPEN/CLOSE button

Disc tray

FF (Fast Forward) button

REW (Rewind) button

When connecting the optical digital cable, remove the cap and fit the connector into the jack firmly. When not using the jack, keep the cap inserted to protect it from dust intrusion.

DVD OPTICAL DIGITAL AUDIO OUT jack (dust protection cap)

DVD S-VIDEO

OUT jack

S-VIDEO/COMPONENT Video selector switch

2C53301C (E)p02-13 21/4/04, 11:0910

DVD COAXIAL DIGITAL

AUDIO OUT jack

DVD AUDIO (L/R) OUT jacks

DVD COMPONENT OUT jacks

AC power cord

DVD/VCR common AUDIO (L/R)/VIDEO OUT jacks

AUDIO (L/R)/VIDEO IN (LINE IN1) jacks

RF IN jack

RF OUT jack

Page 11

Display window

Play indicator

VCR indicator (VCR)

Still indicator

Recording

indicator (VCR)

Track indicator (CD)

T ape loaded indicator (VCR)

Timer Recording indicator (VCR)

VCR operation status

Press CALL to display information on screen. To cancel the display, press CALL again.

While watching TV

DAY OF THE WEEK

CLOCK

STEREO AND

SECOND

AUDIO

PROGRAM

(SAP)

MON

8 : 47 STEREO SAP

CH 125

00 : 00 : 00 SP

REAL TIME COUNTER

CHANNEL

TAPE SPEED

Multifunctional indicator

Progressive indicator

While operating a tape

HI-FI STEREO

8 : 30AMMON

HI-FI

STEREO

OUTPUT SELECTION

Disc inserted indicator (DVD)

OPERATING MODE

AUTO REPEAT

00 : 15 :12 SP

TAPE IN

Disc inserted indicator (CD)

AM/PM indicator (AM is not displayed)

VCR Icons

Recording :

Rec/Pause

Play :

Stop :

Eject :

Introduction

DVD/CD/VCD operation status

Each press of DISPLAY, the status display of the disc will appear on the screen and change as follows.

DVD

ELAPSED

TIME

CD/VCD

DISC

OPERATION

TRACK NO.

2C53301C (E)p02-13 21/4/04, 11:0911

Track 11/99

00:34:56 01:12:33

34:56 71:33

TOTAL TIME

ELAPSED TIME

DISC OPERATION

Title 1/99

1/8

Eng DolbyDigital

1/32

Eng

Chapter 1/999

00:34:56 01:12:33

1/9

TITLE NO.

ANGLE NO. CHAPTER NO. A KIND OF AUDIO

AUDIO LANGUAGE SUBTITLE LANGUAGE

Page 12

Introduction

Identification of Controls (continued)

The instructions in this manual describe the functions on the remote control. See the page in for details.

Remote control

CALL button DISPLAY button

VCR DVD selector button Direct channel

selection buttons Number buttons

28 45

INPUT SELECT button PROGRESSIVE button TV/VCR button

COUNTER RESET button ANGLE button

SP/SLP button PLAY MODE button

REC button OTR button

TIMER REC button PLAY button

REW button SLOW button MARKER button

34 36

ZERO RETURN button JUMP button

VCR MENU button SETUP button

Direction buttons

( / / / )

SET +/

buttons

Channel +/– buttons

40 66

VCR

CALL

DVD

DISPLAY

7 9

INPUT SELECT

PROGRESSIVE

TV/VCR

ANGLE

REC/OTR

SLOW

ZERO RETURN

JUMP

VCR MENU

SETUP

–

CANCEL

SP/SLP

PLAY MODE

TIMER REC

MARKER

SET

ENTER

SET

COUNTER RESET

AUDIO SELECT

PLAY

STOP

TOP MENU RETURN

–

321

654

AUDIO

A-B RPT

INDEX

SKIP

OPEN/CLOSE

CLOCK/COUNTER

FWDREW

PAUSE/STILL

EJECT

ATR

SUBTITLE

INDEX

SKIP

CM SKIP

ZOOM

) buttonPower (

EJECT button (VCR) OPEN/CLOSE button (DVD)

ATR button

SUBTITLE button AUDIO SELECT button

AUDIO button CLOCK/COUNTER button

INDEX + button SKIP button

+–

A-B RPT button INDEX – button

SKIP button

FWD button

STOP button

PAUSE/STILL button TOP MENU button

RETURN button CM SKIP button

ZOOM button *MENU button

ENTER button

52 33

CANCEL button

2C53301C (E)p02-13 21/4/04, 11:0912

* MENU button

Use the MENU button to display the menu included on many DVD video discs. To operate a menu, follow the instructions in “DVD Menu.”

Page 13

Inserting batteries

Introduction

Slide the battery compartment cover in the direction of the

arrow.

Battery precautions

The precautions below should be followed when using batteries in this device:

1.Use only the size and type of batteries specified.

2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. versed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.

Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

5.Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions.)

Install two “R03/AAA” batteries (supplied),

2 3

polarity diagram in the battery compartment.

paying attention to the

Replace the compartment cover.

Re-

Remote control basics

• Press POWER (

• Select your desired operating mode (DVD or VCR) using VCR DVD.

(DVD or VCR indicator on the front panel will show you which mode is selected.)

• Press CH + or CH – to move through the channels one channel at a time.

• The CH +/– (

• You can directly access specific channels using Number buttons.

• Each press of VCR DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the DVD screen (DVD mode).

Operation

• Aim the remote control at the remote sensor and press control buttons to operate.

• Operate the remote control within 30° angle on either side of the remote sensor, up to a distance of Approx. 7 meters.

) to turn the DVD VCR on or off.

/ ) and SET +/– ( / ) are also used to navigate on-screen menu system.

Approx. 7 meters

2C53301C (E)p02-13 21/4/04, 11:0913

Page 14

Connections

OUT

(TV)

(ANT)

OUT

(TV)

(ANT)

OUT

(TV)

(ANT)

Antenna connections

If you are using an antenna system, follow these instructions. If you are a cable (CATV) subscriber, skip ahead to page 16 for the proper connections.

Antenna to DVD/VCR connection

The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV and connect it to the DVD/VCR. Then connect the DVD/VCR to the TV . Below are 3 common methods of connecting an antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.

Combination VHF/UHF Antenna with 75 ohm Coaxial Cable

75 ohm Coaxial Cable

DVD/VCR

Note:

Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire

DVD/VCR

Matching Transformer 300 ohm Input 75

ohm output (not supplied)

300 ohm Twin Lead (Flat) Wire

Separate VHF and UHF Antennas

VHF

If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and one 75 ohm output.

UHF

Combiner 75/300 ohm Inputs 75 ohm output

300 ohm Twin Lead (Flat) Wire

75 ohm Coaxial Cable

(not supplied)

DVD/VCR

(not supplied)

Notes: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to

the DVD/VCR properly.

• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor type antenna is required.

• If you are not sure about the connection, please refer to qualified service personnel.

2C53301C (E)p14-17 21/4/04, 11:0914

Page 15

DVD/VCR to TV connection

After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV. Below are 3 common methods of connecting your DVD/VCR to a TV . Find the type of TV you are using and follow the connection diagram.

This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.

Connections

75 ohm Coaxial Cable (supplied)

Splitter 75 ohm Input

75/300 ohm outputs 75 ohm Coaxial Cable (supplied)

(not supplied)

VHF/UHF IN

UHF

VHF

Note: If a VHF or UHF antenna is used,

set the TV/CATV menu option to the “TV” mode.

TV with single 75 ohm VHF/UHF antenna input

Note: If a VHF or UHF antenna is used,

set the TV/CATV menu option to the “TV” mode.

TV with 300 ohm UHF and 75 ohm VHF antenna inputs

Splitter 75 ohm Input 300 ohm outputs

75 ohm Coaxial Cable (supplied)

2C53301C (E)p14-17 21/4/04, 11:0915

(not supplied)

UHF

VHF

Note: If a VHF or UHF antenna is used,

set the TV/CATV menu option to the “TV” mode.

TV with 300 ohm UHF and 300 ohm VHF antenna inputs

Page 16

Connections

CATV (CABLE TV) connections

Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company supplied converter box, except for those premium channels which are intentionally scrambled. If you subscribe to a premium channel which is scrambled, you must have a descrambler box for proper reception.

DVD/VCR

Incoming Cable

Allows:*Recording of nonscrambled channels.

Use of the programmable timer.

Recording of one channel while watching another.

Incoming

Allows:*Recording of channels through the converter box

Prevents:*Recording one channel while watching another.

Converter/ Descrambler

Cable

(scrambled and unscrambled). Using the programmable timer to record only the

channel selected at the converter box.

Using the DVD/VCR tuner to select channels.

(ANT)

DVD/VCR

(ANT)

OUT (TV)

OUT

(TV)

VH F/UHF

IN (AN T)

VH F/UHF

IN (AN T)

Note:

To record from converter/descrambler, DVD/VCR tuner must be tuned to the converter output channel, usually channel 3 or 4.

DVD/VCR

Incoming Cable

Allows:*Recording of nonscrambled channels.

Use of the programmable timer.

Recording an unscrambled channel while watching

any channel selected at the converter box.

Prevents: Recording scrambled channels.

Note: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output of

the Converter/Descrambler box, usually channel 3 or 4.

(ANT)

OUT

(TV)

Converter/Descrambler

Note:

If you are playing a tape or using the tuner built into the DVD/VCR, the converter must be set to the video channel output of the DVD/VCR (either 3 or 4).

2C53301C (E)p14-17 21/4/04, 11:0916

VH F/UHF

IN (AN T)

Page 17

IMPORTANT: Make sure the TV/CATV menu option is set to the “CATV” mode.

This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult your local cable company for more information concerning connection to their descrambler equipment. There are many ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.

DVD/VCR

Incoming Cable

Splitter

Converter/Descrambler

(ANT)

OUT (TV)

A/B Switch

A B

VHF/UHF

IN (ANT)

Allows:*Recording of one channel while watching another.

Using the programmable timer to record only the channel selected at the converter box.

Recording of all channels through the converter box.

Prevents:*Watching scrambled channels while recording another channel.

Using the DVD/VCR tuner to select channels.

DVD/VCR

Splitter

Incoming Cable

Converter/Descrambler

(ANT)

OUT

(TV)

A/B Switch

A B

VHF/UHF

IN (ANT)

Connections

Allows:*Recording of nonscrambled channels.

Recording of one channel while watching another.

Watching premium channels through the converter while recording nonscrambled channels.

Using the programmable timer.

Prevents: Recording scrambled channels.

DVD/VCR

Splitter

Incoming Cable

Converter/Descrambler

(ANT)

OUT (TV)

Allows:*Recording of all channels through the converter box.

Recording a scrambled or unscrambled channel while watching another (scrambled or

unscrambled) channel. Using the programmable timer to record only the channel selected at the converter box.

Prevents: Using the DVD/VCR tuner to select channels.

A/B Switch

VHF/UHF IN (ANT)

2C53301C (E)p14-17 21/4/04, 11:0917

Page 18

Connections

Connecting to a TV

Connect the DVD/VCR to your TV.

Note: This method transports VHS and DVD-video signals. For enhanced DVD-video performance, we recommend you

also connect the S-video or ColorStream

component video outputs to your TV/monitor. (See page 19.)

Connecting to a TV

Signal flow

(red) (white)

(yellow)

To wall outlet

To VIDEO

OUT

To video input

T o ANALOG AUDIO OUT

Audio/video cable (supplied)

To audio inputs

(yellow)

(red)

(white)

TV or monitor with audio/video inputs

Notes:

• Refer to the owner’s manual of the connected TV as well.

• When you connect the DVD/VCR to your TV, be sure to turn off the power and unplug both units from the wall outlet before making any connections.

• If your television set has one audio input, connect the left and right audio outputs of the DVD/VCR to a Y cable adapter (not supplied) and then connect to your TV.

• Connect the DVD/VCR directly to your TV. If you connect the DVD/VCR to a VCR, TV/VCR combination or video selector, the playback picture may be distorted as DVD video discs are copy protected.

2C53301C (E)p18-25 21/4/04, 11:0918

Page 19

S-video output/input

An S-Video connection is superior to Video (Yellow) output. Use this method for DVD playback when the connected television has SVideo input, and does not have component video inputs.

Component video outputs/inputs

PROGRESSIVE outputs/inputs

Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video signal. Connecting to these inputs allows you to view the highest quality pictures with less flicker.

INTERLACED outputs/inputs

Some TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy the highest quality DVD picture playback.

Notes:

• Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)

• In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such a case, adjust the TV or monitor for optimum performance.

Connections

Connecting to an audio system and TV equipped with S-video input/component video inputs

Note: The S-video output and component video output transports the DVD-video signal exclusively and will deliver

enhanced DVD video picture performance.

Signal flow

(white)

T o ANALOG AUDIO OUT

(red)

When you make this connection, set the S-VIDEO/ COMPONENT Video selector switch to the desired position. And also you must select the corresponding video input on your TV .

Audio cable (not supplied)

To audio inputs of

T o SVIDEO OUT

To PR/CR VIDEO OUT

To PB/CB VIDEO OUT

To wall outlet

To Y VIDEO OUT

Component video cable (not supplied)

the amplifier

To Y video input

PB/CB

video input

PR/CR

video input

(red)

(white)

To S-video input

S-video cable (not supplied)

If you connect the DVD/VCR to your TV with the DVD OUT jacks, select the

TV or monitor with ColorStream

component video inputs

Audio system

corresponding video input on your television to watch DVD video discs.

Notes:

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.

• If you place the DVD/VCR near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD/ VCR away from the tuner and radio.

• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the speakers may be damaged.

• When connecting to a TV using the Video or S-video jack, make sure that the Progressive indicator “

” on the

display window is not lit. If it is lit, the Video and S-video outputs do not feed the correct signals and you cannot see any picture. To turn off the Progressive indicator, select PROGRESSIVE scan Off (see page 66).

2C53301C (E)p18-25 21/4/04, 11:1019

Page 20

Connections

Connecting to optional equipment

You can enjoy high quality dynamic sounds of DVD video discs or audio CDs by connecting the DVD/VCR to optional audio equipment.

For connection to your TV, see “Connecting to a TV”

18 19

Connecting to an amplifier equipped with a Dolby Digital decoder

• This selection uses the following reference mark. : Front speaker

: Rear speaker : Sub woofer

: Center speaker : Signal flow

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs with this dynamic realistic sound by connecting the DVD/VCR to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark.

Manufactured under license from Dolby Laboratories. “Dolby” “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

• Use DVD video discs encoded via the Dolby Digital recording system.

Amplifier equipped with a

Dolby Digital decoder

To COAXIAL

type digital

audio input

To OPTICAL type digital audio input

Optical digital cable

75 Ω coaxial cable

Connect either.

Connecting to an amplifier equipped with Dolby Surround Pro Logic

Dolby Surround Pro Logic

You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left front speakers, a center speaker, and one or two rear speakers).

With an amplifier equipped with Dolby Digital

Connect the equipment the same way as described in “Connecting to an amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.

With an amplifier not equipped with Dolby Digital

Connect the equipment as follows.

• This connectin is only suitable for Video CDs and Audio CDs.

Amplifier equipped with

Dolby Surround Pro Logic

To COAXIAL

type digital

audio input

To OPTICAL type digital audio input

Optical digital cable

75 Ω coaxial cable

Connect either.

Connect one or two rear speakers.

* The output sound from the rear speakers

will be monaural even if you connect two rear speakers.

Connecting to an amplifier equipped with a DTS decoder

Digital Theater Systems (DTS)

DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs. If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS encoded sound tracks on DVD video discs or audio CDs.

Amplifier equipped with a

DTS decoder

T o COAXIAL

type digital audio input

To OPTICAL type digital audio input

Optical digital cable

75 Ω coaxial cable

2C53301C (E)p18-25 21/4/04, 11:1020

Connect either.

“DTS” and “DTS Digital Surround” are trademarks of Digital Theater Systems, Inc.

• Use DVD video discs or audio CDs encoded via the DTS recording system.

Page 21

Warning

When playing DTS-encoded discs (audio CDs), excessive noise may be output from the analog stereo jacks. To avoid possible damage to the audio system, you should take proper precautions when the ANALOG AUDIO OUT (L/R) jacks of the DVD/VCR are connected to an amplification system. (Do not leave the ANALOG AUDIO OUT (L/R) wires dangling.) To enjoy DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR.

Connecting to an amplifier equipped with an MPEG2 audio decoder

MPEG2 sound

You can enjoy motion picture and live concert DVD video discs with dynamic realistic sound by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio processor.

• Use DVD video discs encoded via the MPEG2 recording system.

Amplifier equipped with an MPEG2 audio decoder

To COAXIAL

type digital

audio input

To OPTICAL type digital audio input

Optical digital cable

Connect either.

75 Ω coaxial cable

Connecting to an amplifier equipped with a digital audio input

2 channel digital stereo

You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speaker system (right and left front speakers).

Amplifier equipped with a digital audio input

To COAXIAL

type digital

audio input

To OPTICAL type digital audio input

Optical digital cable

Connect either.

75 Ω coaxial cable

Connections

Notes:

• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the AC-3 RF input of a Dolby Digital Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR.

• Connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the “OPTICAL” or “COAXIAL” input of a Receiver or Processor.

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.

• Turn of f the amplifier before you connect or disconnect the DVD/VCR’ s power cord. If you leave the amplifier power on, the speakers may be damaged.

2C53301C (E)p18-25 21/4/04, 11:1021

Page 22

Basic setup

Setting the video channel

When a TV is connected with the 75 ohm coaxial cable only.

To view playback of a recorded tape or DVD disc, or to watch a program selected by the VCR's channel selector, the TV must be set to channel 3 or 4 (video channel).

Setting the video channel

Press and hold 3 or 4 on the remote for 3 seconds in standby mode.

Press POWER to turn on the DVD/VCR.

The video channel will start to flash for 3 seconds in the display window.

Note: If the unit does not operate properly, or No key operation (by the unit and/or the remote control): Static electricity, etc.,

may affect the player's operation. Disconnect the AC power cord once, then connect it again.

POWER 3

4 TV/VCR VCR DVD

For a push-button TV tuner

If CH 3 or 4 corresponding to the video channel cannot be tuned on your TV, proceed as follows: set the VCR 3/4 channel selector and the TV to CH 3 or 4, play back a prerecorded tape and tune the TV to receive a sharp color picture from the video cassette recorder. Refer to your TV owner's manual for details.

Press VCR DVD selector to select the VCR mode.

VCR DVD

Turn ON the TV and set to CH 3 or 4 to correspond with the channel selected in step 1.

Press TV/VCR to select the VCR position.

The VCR indicator on the front panel will light.

TV/VCR

Select any channel to receive a TV station in your area. The channel number will appear on the screen for

about 4 seconds.

The VCR indicator will appear in the display window.

2C53301C (E)p18-25 21/4/04, 11:1022

Page 23

Setting the language

VCR MENU

SETUP

You can choose from three different languages (English, French and Spanish) for the on-screen displays.

Setting the language

VCR DVD

1,4

1–3 1–3

Preparation:

• Turn ON the TV and select to the corresponding

video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

Press VCR MENU.

VCR MENU

SETUP

The VCR menu screen will appear. Press SET + or – to select “SYSTEM SETUP”, then press ENTER. If you use the unit for the first time and press VCR MENU, instead of the main menu screen the “SYSTEM SETUP” menu screen in step 2 may appear.

SET

–

ENTER

SET

–

MENU TIMER REC SET AUTO REPEAT SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

ON OFF ON OFF

Press SET + or – to select “LANGUAGE”, then press ENTER.

SET

–

ENTER

SET

–

SYSTEM SETUP

CLOCK SET LANGUAGE/IDIOMA/LANGUE NO NOISE BACKGROUND

AUTO CLOCK STANDARD TIME DAYLIGHT SAVING TIME

/ENTER/MENU

ON OFF ON OFF

Press VCR MENU until the MENU screen is cleared.

Notes:

• Both the VCR and the DVD have their own player menus 57.

• If no buttons are pressed for more than 60 seconds, the VCR MENU screen will return to normal TV-operation automatically .

Basic setup

Press SET + or – to select the desired language: English (ENGLISH), Spanish (ESPAÑOL) or

French (FRANCAIS), then press ENTER.

SET

–

2C53301C (E)p18-25 21/4/04, 11:1023

ENTER

SET

–

á+/-

/ENTER/MENU

Page 24

Basic setup

VCR MENU

SETUP

VCR MENU

SETUP

Clock setting

The AUTO CLOCK function will automatically set the built-in clock (Month, Day, Year and Time) when the DVD/VCR is connected to an Antenna or Cable system and it is turned off. The DVD/VCR searches for a station in your area containing the necessary AUTO CLOCK setting signals. Once received, it will take approximately 4 minutes for the clock to set itself automatically.

CALL POWER VCR DVD

1,5

2,4 2,3

AUTO CLOCK setting

Preparation:

• Turn ON the TV and select the corresponding video input.

• Press VCR DVD selector to select the VCR mode. (The VCR indicator will light.)

Connect the Antenna or Cable system.

• If you use a cable box, turn it on.

Plug the AC Power cord to the AC outlet.

Make sure the DVD/VCR is turned off.

Wait at least three minutes and press POWER.

Press CALL to check the clock setting on the on screen display.

CALL

DISPLAY

• If you press POWER, the Auto Clock set is not programmed.

MON

8 : 47 STEREO SAP

CH 125

00 : 00 : 00 SP

T o set AUTO CLOCK to off

When shipped from factory the AUTO CLOCK is set to “ON”. But if you do not want AUTO CLOCK setting:

Press VCR MENU.

Press SET + or – to select “SYSTEM SETUP”, then press ENTER.

SET

–

ENTER

Press SET + or – to select “AUTO CLOCK”.

–

ENTER

–

SET

–

SET

MENU TIMER REC SET AUTO REPEAT SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

MENU TIMER REC SET AUTO REPEAT SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

SYSTEM SETUP

CLOCK SET LANGUAGE/IDIOMA/LANGUE NO NOISE BACKGROUND

AUTO CLOCK STANDARD TIME DAYLIGHT SAVING TIME

/ENTER/MENU

ON OFF ON OFF

ñá+/-

ON OFF ON OFF

If the clock is not set, check the antenna condition. The AUTO CLOCK may not

function properly if the reception condition is not good.

AUTO CLOCK adjustment

The auto clock adjustment will be updated at 6:00 AM, 12:00 PM and 6:00 PM everyday when the DVD/VCR turned off.

• If you use a cable box and you want AUTO CLOCK adjustment to be performed, the cable box must be left on.

• The AUTO CLOCK adjustment is not effective when there is a difference of more than 5 minutes exists between the built-in clock time and the actual time.

2C53301C (E)p18-25 21/4/04, 11:1024

Press ENTER to select “OFF”.

SET

–

ENTER

–

SET

SYSTEM SETUP

CLOCK SET LANGUAGE/IDIOMA/LANGUE NO NOISE BACKGROUND

AUTO CLOCK STANDARD TIME DAYLIGHT SAVING TIME

/ENTER/MENU

Press VCR MENU repeatedly to return to the normal screen.

• When the AUTO CLOCK is set to “OFF”, the AUTO CLOCK adjustment does not function.

• Set the clock manually

ON OFF ON OFF

Page 25

To set STANDARD TIME

VCR MENU

SETUP

VCR MENU

SETUP

To set DAYLIGHT SAVING TIME

In the rare event that you live within broadcast range of two stations in two different time zones, the DVD/VCR may recognize the wrong station for the AUTO CLOCK setting. To correct the situation:

Press VCR MENU.

VCR MENU

SETUP

MENU TIMER REC SET AUTO REPEAT SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

ON OFF ON OFF

ñá+/-

Press SET + or – to select “SYSTEM SETUP”, then press ENTER.

SET

–

ENTER

–

SET

Press

SET + or –

then press ENTER.

SET

–

ENTER

–

SET

to select “ST ANDARD TIME”

MENU TIMER REC SET AUTO REPEAT SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

SYSTEM SETUP

CLOCK SET LANGUAGE/IDIOMA/LANGUE NO NOISE BACKGROUND

AUTO CLOCK STANDARD TIME DAYLIGHT SAVING TIME

/ENTER/MENU

ON OFF ON OFF

Press SET + or – to select your time zone, then press ENTER.

SET

–

ENTER

–

SET

ATLANTIC : GMT–4hours

EASTERN : GMT–5hours CENTRAL : GMT–6hours MOUNTAIN : GMT–7hours PACIFIC : GMT–8hours ALASKA : GMT–9hours HAWAII : GMT–10hours AUTO : AUTO SET (GMT : Greenwich Mean Time)

Press VCR MENU twice to return to the normal screen.

VCR MENU

SETUP

Y ou can set the DAYLIGHT SAVING TIME automatically or manually.

Press VCR MENU. Press SET + or – to select “SYSTEM SETUP”,

then press ENTER.

TIMER REC SET

AUTO REPEAT

SET

–

ENTER

–

SET

SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

ON OFF ON OFF

Press SET + or – to select “DA YLIGHT SAVING TIME”, then press ENTER.

SET

–

ENTER

–

SET

SYSTEM SETUP

CLOCK SET LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

AUTO CLOCK STANDARD TIME

DAYLIGHT SAVING TIME

/ENTER/MENU

ON OFF ON OFF

Press SET + or – to select one of the options, then press ENTER. Press VCR

MENU until the MENU screen is cleared.

ON:

for manual setting (forward one hour)

OFF:

for manual setting (back one hour)

AUTO:

for automatic setting (read XDS in the signal)

SET

–

ENTER

–

SET

When you want to set the SAVING TIME

Sunday in April you set to “ON”, and

manually, on the first

on the last Sunday in October you set to “OFF”.

DAYLIGHT SAVING TIME

OFF

AUTO

/ENTER/MENU

DAYLIGHT

Basic setup

Notes:

• To be able to select the standard time, the clock must first be set by AUTO CLOCK once.

• If you live in Newfoundland and the AUTO CLOCK does not function properly, set the AUTO CLOCK menu option to “OFF” and set the clock manually.

2C53301C (E)p18-25 21/4/04, 11:1025

Notes:

• When shipped from factory, the DAYLIGHT SAVING TIME is

set to “AUTO” position.

• When the clock is not set, DAYLIGHT SAVING TIME setting is not available.

• When there is no DAYLIGHT SAVING TIME in your area, always select “OFF” position in step 3.

Page 26

Basic setup

Clock setting (continued)

If the AUTO CLOCK process did not set the date and time correctly, you must set them manually for timer recording and DAYLIGHT SAVING TIME.

Manual clock setting

2–4 CANCEL

2–4

EXAMPLE: Setting the clock to “8:30 AM” March,

27 (SAT), 2004.

Press VCR MENU.

VCR MENU

SETUP

Press SET + or – to select “SYSTEM SETUP”, then press ENTER.

SET

–

ENTER

–

SET

MENU TIMER REC SET AUTO REPEAT SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

ON OFF ON OFF

Press SET + or – to select “CLOCK SET”, then press ENTER.

SET

–

ENTER

–

SET

SYSTEM SETUP

CLOCK SET LANGUAGE/IDIOMA/LANGUE NO NOISE BACKGROUND

AUTO CLOCK STANDARD TIME DAYLIGHT SAVING TIME

á+/-

/ENTER/MENU

ON OFF ON OFF

After setting the clock, date and time starts functioning automatically.

8 : 30

SAT

To make corrections any time during the process

Press CANCEL repeatedly until the item you want to change blinks, then press SET + or –.

Note:

After a power failure or disconnection of the power, the timer settings will be lost. In this case, reset the present time.

Press SET + or – to set the month, then press ENTER.

SET

–

ENTER

–

SET

Set the day, year and time as in step 4.

2C53301C (E)p26-31 21/4/04, 11:1026

MONTH

DAY

1 (MON)

YEAR

2004

TIME

12 : 00

3 27 (SAT) 2004

8 : 30

〈+/–/ENTER/CANCEL/MENU 〉

MONTH

DAY YEAR TIME

á+/–

/ENTER/CANCEL/MENU ñ

Page 27

Tuner setting

VCR DVD

This DVD/VCR is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the DVD/VCR’s memory. In addition to normal VHF and UHF channels, this DVD/VCR can receive up to 113 Cable

1,4

TV channels. To use this DVD/VCR with an antenna, set the TV/CATV menu option to the TV mode. When shipped from the factory , this menu option is in the CATV mode.

1,3 1,2

TV/CATV selection Setting channels automatically

Preparation:

• Turn ON the TV and select to the corresponding video input.

• Press VCR DVD selector to select the VCR mode. (The VCR indicator will light.)

Press VCR MENU. Press “CH SETUP”, then press ENTER.

VCR MENU

SETUP

SET

–

ENTER

SET

–

SET + or –

MENU TIMER REC SET AUTO REPEAT SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

to select

ON OFF ON OFF

Press SET + or – to select “TV/CATV”.

SET

–

ENTER

SET

–

CH SETUP

TV CATV AUTO CH MEMORY ADD/DELETE

á+/-

/ENTER/MENU

Press ENTER to select the TV or CATV mode.

SET

–

ENTER

SET

The arrow indicates the selected mode.

–

CH SETUP

AUTO CH MEMORY ADD/DELETE

TV CATV

TV - VHF/UHF channels

á+/-

CATV - CABLE TV channels

/ENTER/MENU

Repeat left step 1 and press SET + or – to select “AUTO CH MEMORY”.

SET

–

ENTER

SET

–

CH SETUP

á+/-

Press ENTER.

Auto tuning will begin. The channel display will count up and when finished, the screen returns to normal.

SET

–

ENTER

SET

–

TV CATV AUTO CH MEMORY ADD/DELETE

/ENTER/MENU

Basic setup

CH 002

Press VCR MENU until the menu screen is cleared.

VCR MENU

SETUP

Note:

You can’t select “CH SETUP” if you set the channel to “L1” or “L2”.

2C53301C (E)p26-31 21/4/04, 11:1027

Page 28

Basic setup

VCR MENU

SETUP

Tuner setting (continued)

NUMBER BUTTONS

3 1,2

1,2

To ADD/DELETE channels

Repeat the step 1 on page 27. Then press SET + or – to select the “ADD/DELETE” and press

ENTER.

SET

–

ENTER

SET

–

To Add or Delete desired channels

Press Number buttons or SET + or – to select a channel number you want to add or delete.

To add channels

Press ENTER until “ADD” appears on the screen.

To delete channels

Press ENTER until “DELETE” appears on the screen. The channel number will blink.

Repeat to to add or delete other channel.

7 9

1 2

321

654

SET

–

ENTER

–

SET

CH SETUP

TV CATV

AUTO CH MEMORY

ADD/DELETE

á+/-

/ENTER/MENU ñ

Noise elimination

When you don't want to receive a weak signal broadcast, a Blue back screen can be obtained by selecting the NO NOISE BACKGROUND “ON”. When the unit is shipped from the factory, the NO NOISE BACKGROUND is set to “ON”.

Repeat the steps 1~2 on page 26 and press SET + or – to select “NO NOISE

BACKGROUND”.

SET

–

ENTER

–

SET

Press ENTER to select “ON” or “OFF” position.

SET

–

ENTER

SET

–

Press VCR MENU until the menu screen is cleared.

SYSTEM SETUP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

AUTO CLOCK

STANDARD TIME

DAYLIGHT SAVING TIME

SYSTEM SETUP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

AUTO CLOCK

STANDARD TIME

DAYLIGHT SAVING TIME

/ENTER/MENU

ON OFF ON OFF

Press VCR MENU until the menu screen is cleared.

VCR MENU

SETUP

2C53301C (E)p26-31 21/4/04, 11:1028

Page 29

Playback (VCR)

Loading and unloading a cassette tape

Use only video cassette tapes marked and .

Push the center of the tape until it is automatically inserted.

Automatic power ON

When you insert a cassette tape the DVD/VCR power will turn ON automatically.

Automatic playback

When loading a cassette tape without an erase prevention tab, playback will start automatically.

Unloading

Press EJECT on the front panel or on the Remote.

Insert the cassette tape with its labeled side facing up and the erase prevention tab positioned at your left. An inverted cassette tape cannot be inserted.

Erase prevention tab

Remove the cassette tape.

EJECT

Basic setup

Playback (VCR)

Automatic tape eject

This DVD/VCR will automatically rewind the tape when the tape has ended. Once the tape is rewound to its beginning, the cassette tape will be ejected automatically.

To prevent accidental erasure

Remove the erase prevention tab with a screwdriver.

Screwdriver

Erase prevention tab

To record again

Cover the hole with a piece of adhesive tape.

Adhesive tape

Tape speed and maximum recording time

Tape Speed

SP (Standard Play)

SLP (Super Long Play)

T-160 T-120 T-90 T-60 T-30

2-2/3 hours 2 hours 1-1/2 hours 1 hour 30 minutes

8 hours 6 hours 4-1/2 hours 3 hours 1-1/2 hours

Video cassette tape

2C53301C (E)p26-31 21/4/04, 11:1129

Page 30

Playback (VCR)

FWD

REW

Cassette tape playback

To play a prerecorded tape.

VCR DVD

REW PLA Y

FWD STOP

Playback Rewind or forward the tape

Preparation:

• Turn ON the TV and select the corresponding video input.

• Press VCR DVD selector to select the VCR mode. (The VCR indicator will light).

Load a prerecorded tape

(When loading a cassette tape without the erase prevention tab, playback will start automatically).

Stop the playback or recording via STOP on remote.

To rewind the tape:

To forward the tape:

Press FWD.

Press REW.

To start playback

PLAY

To stop playback

Notes:

• This VCR selects the playback tape speed SP , LP or SLP automatically.

• The Cassette tape and DVD disc can be played back simultaneously. If you press VCR DVD selector, the tape playback and DVD playback alternate with each other on the screen (via CH3, 4 or video connection).

Press PLAY. Playback will start. “ on the screen for about 4 seconds.

Press STOP once. The tape will stop but remain fully loaded and ready to play. “

” will appear on the screen for

about 4 seconds.

” will appear

To discontinue the tape-winding, press STOP. To switch to playback directly (without STOP), press PLAY.

Forward/Reverse picture search mode

When the tape is being winded, you can switch to picture search mode (see next page). To do this, press REW or FWD and hold it down. The unit will resume the tape advance or rewinding as soon as the button is released.

2C53301C (E)p26-31 21/4/04, 11:1130

Page 31

Special playback

SLOW ATR

REW PLAY

FWD PAUSE/STILL

CM SKIP SET +/–

Picture search

Reverse picture search function Press REW once or twice during playback. Forward picture search function

Press FWD once or twice during playback. To return to playback, press PLAY.

SPEED SEARCH TIMES

TAPE SPEED

SP (Standard Play) LP (Long Play) SLP (Super Long Play)

PICTURE SEARCH SPEED

PRESS ONCE

3 X 7 X 9 X

PRESS TWICE

15 X

5 X 9 X

Still picture

Press PAUSE/STILL during playback. To resume normal playback, press PLAY or PAUSE/STILL.

Slow motion

During playback press SLOW. To return to playback, press PLAY or SLOW.

Slow tracking and vertical lock adjustment

If noise bars appear in the picture during slow motion, press the SET + /– to reduce the noise bars. If the still picture jitters excessively, press SET +/– to stabilize the still picture.

Frame by frame picture

Press PAUSE/STILL during playback. Press SLOW repeatedly: The picture advances frame by frame. To return to playback, press PLAY or PAUSE/STILL.

CM skip

Press CM SKIP during playback. The DVD/VCR will search forward through approximately 30 seconds of the tape (e.g. unwanted commercial time) for each press of CM SKIP (maximum six presses) and then resume normal playback.

For example : 1 press: 30 seconds of tape

2 press: 60 seconds of tape 3 press: 90 seconds of tape

Adjusting tracking condition

Automatic tracking adjustment

Whenever you insert a tape and start playback, the automatic tracking feature continuously analyzes the signal to enable optimum picture quality during playback.

Manual tracking adjustment

If automatic tracking cannot eliminate noises well during playback, press SET +/– to eliminate the noise. “MANUAL TR.” will appear on the screen. Press it briefly for a fine adjustment, or press and hold for a coarse adjustment.

Press ATR to reactivate automatic tracking again. “AUTO TR.” will appear on the screen.

AUTO TR.

Notes:

•

The audio output is muted during SPEED SEARCH, STILL, FRAME ADVANCE and SLOW MOTION.

• During picture search mode there will be noise bars. This is not a defect.

• Playback will commence after approx. 5 minutes to protect the video tape against excessive wear during pause mode.

Video head cleaning

Video head clogging

The video heads are the means by which the DVD/VCR reads the picture from the tape during playback. In the unlikely event that the heads become dirty enough to be clogged, no picture will be displayed. This can easily be determined if, during playback of a known good tape, there is good sound, but no picture (picture is extremely snowy). If this is the case, have the DVD/VCR checked and cleaned by qualified service personnel.

Notes:

DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR

•

SERVICE THE UNIT BY REMOVING THE REAR COVER. Video heads may eventually wear out and should be re-

•

placed when they fail to produce clear pictures. To help prevent video head clogging, use only good qual-

•

ity VHS tapes. Discard worn out tapes.

Good Picture

Snowy Picture

Playback (VCR)

2C53301C (E)p26-31 21/4/04, 11:1131

Page 32

Playback (VCR)

CLOCK/COUNTER

COUNTER RESET

ANGLE

ZERO RETURN

JUMP

Convenience function

Repeat playback

The entire video tape will play until its end. The tape will automatically rewind to the beginning and the playback will be repeated.

Press VCR MENU.

Press SET + or – to select “AUTO

REPEAT”.

VCR MENU

SETUP

SET

–

ENTER

SET

–

Press ENTER to select “ON” or “OFF”.

SET

–

ENTER

–

SET

If “ON” is selected, the playback will be repeated endlessly.

MENU TIMER REC SET AUTO REPEAT SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

MENU TIMER REC SET AUTO REPEAT SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

ON OFF ON OFF

CALL COUNTER RESET CLOCK/COUNTER

VCR MENU

PLAY STOP

ZERO RETURN ENTER SET +/–

Zero return function

This function rewinds the tape to the automatically .

Press CLOCK/COUNTER.

The counter display shows the tape running time during playback or recording.

Press COUNTER RESET at the desired tape position.

The counter display will be reset to “00:00:00” position (e.g. the beginning of recording).

“00:00:00”

counter position

Press VCR MENU until the menu screen is cleared.

VCR MENU

SETUP

appear on the screen 11.

If you press CALL, “ ” will

To commence playback, press PLAY.

endlessly.

PLAY

The playback will be repeated

To cancel repeat mode: Follow the above step 1, then press ENTER to select “OFF” position. Press VCR MENU to return to the TV.

2C53301C (E)p32-37 21/4/04, 11:1132

Press STOP when playback or recording is completed.

Press ZERO RETURN.

The tape will automatically rewind or fast forward to the “00:00:00” counter position.

Page 33

VCR DVD

CLOCK/COUNTER INDEX

+/–

STOP

Clock/counter display

Press CLOCK/COUNTER. The clock and tape counter alternate with each other in the display window.

COUNTER

CLOCK/COUNTER

CLOCK

Press VCR DVD selector. The DVD mode and the VCR mode alternate with each other in the display.

DVD mode

VCR DVD

VCR mode

Notes:

• If you rewind the tape beyond “00:00:00”, a minus sign (“–”) will be displayed in front of the time.

• When you load a tape, the counter will reset to “00:00:00”.

• The counter does not function on nonrecorded (blank) sections of the tape. When you rewind, fast forward or play tapes through blank sections, the counter stops.

Video index search system

This function enables you to locate the beginning of any recording made on the VCR.

Recording an INDEX mark

The Index Search function auto-

CH 001

matically records an INDEX mark on the tape whenever a recording is initiated.

INDEX

Index search

Press INDEX + or – during stop or play mode. For Succeeding programs: Press INDEX +. For Preceding programs: Press INDEX –. (As many as 9 index points can be accessed via this method.) When the INDEX + or – is pressed, the unit starts searching the INDEX

NO. selected and finds the portion, then playback starts automatically. To stop the Index Search, press STOP.

INDEX

–

SKIP

Notes:

• When you record an INDEX mark at the very beginning of the tape, the mark may not be found.

• During INDEX search, the tape may stop and begin to play at a slightly different location.

• INDEX may not function properly with old or worn out video tapes.

• INDEX marks may not be found if it is extremely close to the point where the search began.

• In recording, if you stop recording temporarily, the INDEX mark is not recorded on the tape.

INDEX

SKIP

or is displayed

INDEX NO. (up to 9)

SQPB (S-VHS Quasi Playback)

Playback (VCR)

2C53301C (E)p32-37 21/4/04, 11:1133

You can playback video cassette tapes recorded in the S-VHS system. However, the picture will not have the high resolution of S-VHS system.

Note: You cannot record S-VHS video format with this VCR.

Page 34

Recording (VCR)

REC/OTR

Recording a TV program

Recording and viewing the same TV program.

Recording a TV program

VCR DVD

4 2 5

Preparation:

• Turn ON the TV and select to the corresponding video input.

• Press VCR DVD selector to select the VCR mode. (The VCR indicator will light.)

Load a cassette tape with the erase prevention tab intact.

The DVD/VCR will automatically turn on.

Press SP/SLP to select the desired tape speed SP or SLP.

The tape counter and “SP” or “SLP” will appear on the screen for about 4 seconds.

SP/SLP

PLAY MODE

00 : 00 : 00 SP

Select “TV” or “CATV” to the appropriate position

TV - VHF/UHF channels CATV - CABLE TV channels

Press Number button or CH +/– to select the channel to be recorded.

321

654

7 9

TV mode direct channel selection:

All channels can be instantly selected by using two buttons. (for example, to select channel 2, press “0”, then “2”. If you press only “2”, channel selection will be delayed for two seconds.) For channels 10 and above, press the 2 digits in order.

CATV mode direct channel selection:

1-9 Press 0 twice and then 1-9 as required. 10-12 Press 0 first and then the remaining 2 digits in

13-99 Press 2 digits in order. 100-125 Press the 3 digits in order.

VHF/UHF/CATV CHANNELS

Press REC/OTR.

“ ” will appear on the screen

appear on the display window.

Example: To select “2”, Press 002. order from left to right.

Example: Press 012 for “12”. Example: Press 22 for “22”. Example: Press 110 for “110”.

TV CATV

VHF 2-13

UHF

14-69

for about 4 seconds and “REC” will

SET

–

ENTER

–

SET

VHF 2-13

STD/HRC/IRC

14-36 (A) (W)

37-59 (AA) (WW)

60-85 (AAA) (ZZZ)

86-94 (86) (94)

95-99 (A-5) (A-1)

100-125 (100)(125)

01 (5A)

CH 110

INDEX

2C53301C (E)p32-37 21/4/04, 11:1134

Page 35

To stop recording

TV/VCR

PAUSE/STILL STOP

Press STOP to stop recording.

4 seconds.

“ ” will appear on screen for about

T o stop recording temporarily

Press PAUSE/STILL to avoid recording unwanted material. Press again to continue the recording.

“ ” will appear on screen for about 4 seconds.

Notes:

•

The pause function will be released after 5 minutes to prevent damage to the tape or the VCR. The VCR will change to the STOP mode.

• You can select a recording channel in the recording pause mode.

Auto Rewind feature

This VCR will automatically rewind the tape when the tape has ended (except during OTR and timer recording). It will also eject the tape.

Recording (VCR)

Recording one program while watching another

While the VCR is recording, select your desired channel on the TV. When a TV is connected with an antenna cable only, press TV/VCR to select the TV position. The “VCR” display will go off and recording will continue. Select the TV channel you want to watch by using the TV channel selector.

Note:

Some CATV hookups do not permit viewing one channel while recording another. See pages 16 and 17.

2C53301C (E)p32-37 21/4/04, 11:1135

Page 36

Recording (VCR)

7 9

654

321

REC/OTR

One-touch Timer Recording (OTR)

The One-touch Timer Recording feature provides a simple and convenient way to make a timed recording.

One-touch Timer Recording (OTR)

VCR DVD

4 2 5

STOP 4

Preparation:

• Turn ON the TV and select to the corresponding video input.

• Press VCR DVD selector to select the VCR mode. (The VCR indicator will light.)

Example: One-touch Timer Recording for 30 minutes.

Load a cassette tape with the erase prevention tab intact.

The VCR will automatically turn on.

Press SP/SLP to select the desired tape speed SP or SLP.

PLAY MODE

SP/SLP

The tape counter and “SP” or “SLP” will appear on the screen for about 4 seconds.

00 : 00 : 00 SP

Press Number button or CH +/– to select the channel to be recorded.

SET

–

Press

REC/OTR

button again to stop recording after 30 minutes.

Each additional press of

ENTER

–

SET

. Recording begins. Press the

REC/OTR

will increase recording time as shown in the chart below, up to a maximum of 6 hours.

The OTR and recording time will appear on the screen for about 4 seconds. And, “ ” will appear on the display.

Press once twice 3 times 4 times 5 times

Recording time

NORMAL REC

0:30 1:00 1:30 2:00

Press 6 times 7 times 8 times 9 times 10 times

Recording time

3:00 4:00 5:00

6:00

NORMAL REC

CH 110

OTR 0 : 30

CH 110

Set “TV” or “CATV” option to the appropriate

position

2C53301C (E)p32-37 21/4/04, 11:1136

TV - VHF/UHF channels CATV - CABLE TV channels

INDEX

To cancel OTR

Press STOP or turn off the power.

“ ” will appear on screen for about 4 seconds.

Note:

If you wish to watch the DVD playback during OTR or standard recording, press VCR DVD selector to change to DVD mode and

perform the DVD playback 43.

Page 37

Timer recording

VCR MENU

SETUP

TIMER REC

Timer recording can be programmed on-screen with the remote control. The built-in timer allows automatic unattended recording of up to 8 programs within 1 month.

Timer recording

VCR DVD EJECT

2,3 TIMER REC

1,5 1–3 CANCEL

Preparation:

• Press VCR DVD selector to select the VCR mode.

• Load a cassette tape with the erase prevention tab intact.

• Check the time and date are correct

Example: Program a timer recording for the 26th day,

channel 125

(CATV), 11:00 - 11:30 PM on timer program

number 1 (Tape speed: SLP).

Press VCR MENU. Select “TIMER REC SET”, then press ENTER.

MENU TIMER REC SET AUTO REPEAT SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

ON OFF ON OFF

ñá+/-

VCR MENU

SETUP

SET

–

ENTER

–

SET

Press SET + or – to select one of the program line, then press ENTER.

DATE START END CH

SET

–

ENTER

–

SET

Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð

á+/Ð

/ENTER/CANCEL/MENU

Ð Ð Ð Ð Ð Ð Ð Ð

Press SET + or – to select the date, then press ENTER.

SET

–

ENTER

–

SET

DATE START END CH

Ð : Ð Ð Ð : Ð Ð Ð Ð Ð

26(SU)

Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð

á+/Ð

/ENTER/CANCEL/MENU

Ð Ð Ð Ð Ð Ð Ð Ð

Set the start time, end time, channel and tape speed as in step 3.

Notes:

DATE START END CH

26(SU)11:00PM11

+/Ð/ENTER/CANCEL/MENU

:30PM125

SLP

Ð Ð Ð Ð Ð Ð Ð

• Press CANCEL to move cursor backward for correction.

• To record from external source set the channel to “L1” or “L2”.

To enter other programs, repeat step 2 through 4.

• To return to the normal screen, press VCR MENU twice.

DATE START END CH

26(SU)11:00PM11

+/Ð/ENTER/CANCEL/MENU

:30PM125

SLP

Ð Ð Ð Ð Ð Ð Ð

Press TIMER REC. The timer symbol ( ) will appear on the display and the VCR stands by

for recording.

At the same time, VCR mode will change to DVD mode automatically. You can use DVD even if the VCR is in the timer recording mode. If you do not use the DVD, turn the power off.

Notes:

• The timer recording will start at 5 seconds before the time you predetermined.

• If the timer symbol( ) does not appear on the display in spite of the pressing of TIMER REC, the cassette may not

have been loaded.

• If the cassette is ejected in spite of the pressing of TIMER REC, the erase prevention tab of the cassette may have

been removed.

Notes:

• If the timer symbol ( ) blinks when the timer recording ended, the TV program has not been completely recorded because of an insufficient tape length. Press TIMER REC to cancel the timer program or press EJECT to remove the cassette tape.

• During timer recording standby mode, the VCR mode cannot be operated. To use the VCR, press TIMER REC at first, then press VCR DVD selector to change to VCR mode. After you use the VCR, press TIMER REC again to put the VCR into timer recording standby mode.

• If you press TIMER REC during timer recording, the recording operation will be interrupted. If you press TIMER REC again within the programmed time, the recording operation will start again.

• After a power failure or disconnection of the power plug, all programmed recording settings and time display will be lost

upon resumption of power. In this case, reset the clock 24 and reprogram any timer recording.

Recording (VCR)

2C53301C (E)p32-37 21/4/04, 11:1237

Page 38

Recording (VCR)

TIMER REC

VCR MENU

SETUP

Timer recording (continued)

VCR DVD

SET +/– TIMER REC

VCR MENU ENTER CANCEL

Setting procedure

To set daily/weekly timer

Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g. MOSA: Monday to Saturday) Timer recording

Follow the procedure of timer recording on the previous page. At step 3 press SET + or – repeatedly until the desired setting appears. Then press ENTER.

When you press SET – repeatedly, the DATE indicator will change as follows, in this case the day is Friday.

The current day (Friday) SU-SA (Sunday to Saturday)

One month later

minus one day

MO-SA (Monday to Saturday) MO-FR (Monday to Friday)

WKL-WE WKL-TH (Weekly Thursday)

(Weekly Wednesday)

SET

–

ENTER

–

SET

DATE START END CH

WKL-WE

á+/–

/ENTER/CANCEL/MENU

If the programs overlap another

Do not overlap timer programs as portions of the conflicting programs will be lost. The first recording time has priority over the next recording time as shown in the diagram below.

Program 1 Program 2

Program 3

Recording Control Settings

8 : 00

Prog.1

9 : 00

Deleted Parts

Non Recorded Portion Parts

Prog.2 Prog.3

10 : 00

11 : 00

To confirm or cancel a program

If the Timer has been activated, press TIMER REC to deactivate the Timer.

To confirm Timer program:

At step 1 on the previous page select “TIMER REC

SET” and press ENTER. The timer program list will appear on the screen.

SET

–

ENTER

–

SET

T o cancel Timer program:

Press SET + or – to select the unwanted program,

then press CANCEL to cancel the program.

SET

–

ENTER

–

SET

Press VCR MENU repeatedly until the menu screen is cleared.

The timer symbol ( ) will disappear. Then press VCR DVD selector to change to VCR mode.

VCR DVD

DATE START END CH

26(SU)11:00PM11

á+/–

/ENTER/CANCEL/MENU

DATE START END CH

Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð

CANCEL

Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð

á+/Ð

/ENTER/CANCEL/MENU

:30PM125

SLP

Ð Ð Ð Ð Ð Ð Ð Ð

Notes:

• The daily/weekly recording can be made continuously until the recording is canceled or the tape reaches the end.

• During timer recording the automatic rewinding mechanism does not function.

2C53301C (E)p38-41 21/4/04, 11:1238

Notes:

• If there are other timer record programs remaining, TIMER REC must be pressed to reactivate the timer, otherwise the

remaining timer record programs will be ignored.

• You cannot confirm the Timer program during timer recording operation.

• You can correct or cancel a programmed setting in program confirm mode.

Page 39

Other functions (VCR)

Stereo recording and playback / Second Audio Program (SAP)

AUDIO SELECT SET +/–

VCR MENU ENTER CANCEL

Stereo recording and playback

The VHS Hi-Fi audio system permits high fidelity recording of MTS STEREO TV broadcasts.

When a MTS STEREO broadcast is received, “STEREO” will appear on the screen for about 4 seconds and the program can be viewed or recorded in stereo. The Hi-Fi stereo recording procedure is the same as for normal recordings.

Note:

When using a CATV system, stereo TV programs may be transmitted over a mono cable channel. In this case “STEREO” will not appear and the sound will be in mono.

AUDIO SELECT

AUDIO

Output selection

When viewing an MTS stereo TV program, or playing a prerecorded VHS Hi-Fi stereo videotape, press AUDIO SELECT to select how the audio will be heard through the speakers. Normally set to the Hi-Fi stereo position, this button can be set to the MONO position if the stereo broadcast or videotape audio is of poor quality. The “R” and “L” positions allow the audio from the Right or Left HiFi channel to be heard over both TV speakers. This button has no effect when viewing a MONO videotape or TV program. Each time when you press the button, OUTPUT SELECTION display appears on the screen for several seconds. Refer to the chart below.

OUTPUT SELECTION

STEREO L CH R CH MONO

SOUND HEARD ON BOTH SPEAKERS

STEREO LEFT CHANNEL AUDIO RIGHT CHANNEL AUDIO MONO

STEREO

Second Audio Program (SAP)

Your DVD/VCR is fitted with a SAP broadcast system which enables you to switch to a second audio program when viewing a selected channel. This function applies only when the program is broadcast in multi-languages through the SAP broadcast system.

Press VCR MENU. Then press SET + or – to select “SAP”.

VCR MENU

SETUP

SET

–

ENTER

SET

–

Press ENTER to select “ON”.

Then press VCR MENU until the menu screen is cleared.

SET

–

ENTER

–

SET

VCR MENU

SETUP

Listening to SAP

When the VCR is turned on or a channel selection is made, make certain the letters “SAP” appears on the screen for about 4 seconds. This means that the “Second Audio Program” broadcasting is available.

STEREO SAP SAP

TIMER REC SET

AUTO REPEAT

SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

TIMER REC SET AUTO REPEAT

SAP CH SETUP SYSTEM SETUP

á+/-

/ENTER/MENU

ON OFF ON OFF

Other functions (VCR)

2C53301C (E)p38-41 21/4/04, 11:1239

Notes:

• When playing back a tape that is not recorded in Hi-Fi stereo mode, the audio will automatically be monaural.

• When listening to a VHS Hi-Fi video tape or MTS broadcast through the VHF/UHF jack (Audio/Video cable not connected), the sound will be monaural.

Page 40

Other functions (VCR)

Duplicating a video tape

If you connect the DVD/VCR to another VCR or Camcorder, you can duplicate a previously recorded tape. Make all connections before turning on the power.

Duplicating a video tape

Preparation:

• Turn ON the TV and select the corresponding video input.

• Press VCR DVD selector to select the VCR mode. (The VCR indicator will light.)

• Load a cassette tape with the erase prevention tab intact.

• Load a previously recorded tape into the playback VCR or Camcorder.

Press SP/SLP to select the desired tape speed SP or SLP.

SP/SLP

PLAY MODE

It is recommended that you set the tape speed to the SP mode on the recording VCR for best results.

Connection with second VCR

T o VIDEO OUT T o AUDIO (R) OUT

AUDIO/VIDEO cable (supplied)

VCR DVD 2

1 4

Playback VCR

To AUDIO (L) OUT

Recording VCR

Press INPUT SELECT once or twice to select AUDIO/VIDEO input position.

“L1” or “L2” will appear in the display.

INPUT SELECT

PROGESSIVE

L1: on the rear panel L2: on the front panel

Press PLAY on the playback VCR or Camcorder.

Press REC/OTR on the recording VCR.

The duplicating process begins.

REC/OTR

Press STOP after duplicating a video tape.

To VIDEO IN

Connection with Camcorder

Playback Camcorder

To AUDIO (L) IN

To VIDEO IN

For duplicating a previously recorded tape from a camcorder, follow the camcorder manufacturer’s instructions. A typical camcorder dubbing hookup is shown above.

T o AUDIO (R) IN

T o AUDIO (L) IN

To AV Jack

Recording VCR

T o AUDIO (R) IN

AUDIO/VIDEO cable (not supplied)

2C53301C (E)p38-41 21/4/04, 11:1240

Page 41

Recording a DVD/CD disc

You can record disc material in DVD, Audio CD, etc. onto a V ideo tape with this DVD/VCR.

Duplicating a DVD or CD disc

1 4

Preparation:

• Turn ON the TV and select the corresponding video input.

• Press VCR DVD selector to select the VCR mode. (The VCR indicator will light.)

•

Load a cassette tape with the erase prevention tab intact.

• Load a DVD/CD disc.

Press SP/SLP to select the desired tape speed SP or SLP.

SP/SLP

PLA Y MODE

00 : 00 : 00 SP

Press VCR DVD selector to select the DVD mode.

VCR DVD

Press PLAY to start playback.

The DVD indicator will light.

PLAY

Notes:

• You may not be able to record the beginning of the disc. Begin VCR recording once program playback commences on the DVD.

• When the scanning mode is set to the progressive mode, you cannot duplicate a disc material onto a video tape. When REC/OTR is pressed, the PROGRESSIVE indicator

” on the display window will flash and “Please Set

“ Off” will appear on the screen.

• You can not record discs encoded with copy guard function. The following icon and text will show up on the TV screen.

DISC IS COPY PROTECTED

Other functions (VCR)

Press REC/OTR to start recording.

REC/OTR

Press STOP if you finish recording.

2C53301C (E)p38-41 21/4/04, 11:1241

The DVD/VCR will change to the VCR mode automatically and the playback picture or sound will be duplicated on the video cassette tape.

If you wish to stop a DVD/CD disc, press VCR DVD selector to change the DVD mode, then press STOP.

Page 42

Basic playback (DVD)

Playing a disc

This section shows you the basics on how to play a disc.

CAUTION

Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious personal injury.

DVD VCD

Basic playback

Preparations:

• When you want to view a disc, turn on the TV and select the corresponding video input connected to the DVD/VCR. This may include S-video or component video inputs which are exclusive to DVD playback.

• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected to the DVD/VCR.

Press ON/STANDBY (I / ).

Press VCR/DVD SELECT to select the DVD mode.

Press OPEN/CLOSE.

The DVD/VCR turns on.

The DVD indicator will light.

The disc tray opens.

Press OPEN/CLOSE or PLAY on the unit.

• A menu screen will appear on the TV screen, if the disc has a menu feature.

Press / or / to select title.

SET

–

ENT ER

–

SET

Display window STOP PLAY

The disc tray closes automatically. On the TV-screen, “ ” “Reading” and then playback commences.

changes to

Reading

Place the disc on the disc tray.

• There are two different disc sizes. Place the disc in the correct guide on the disc tray. If the disc is out of the guide, it may damage the disc and cause the DVD/VCR to malfunction.

• Do not place a disc which is unplayable in this DVD/VCR.

2C53301C (E)p42-45 21/4/04, 11:1242

With the playback side down

Press ENTER.

SET

–

ENT ER

–

SET

Press STOP to end playback.

To start playback in the stop mode

Press PLAY.

• Title is selected and play commences.

• The unit records the stopped point, depending on the disc. “ appears on the screen. Press PLAY

to resume playback (from

the scene point).

• If you press STOP again or unload the disc (“ screen.), the unit will clear the stopped point.

” appears on the

”

Page 43

VCR DVD OPEN/CLOSE

PLAY PAUSE/STILL

STOP ENTER

To obtain a higher quality picture

Occasionally, some picture noise not usually visible during a normal broadcast may appear on the TV screen while playing a DVD video disc because the high resolution pictures on these discs include a lot of information. While the amount of noise depends on the TV you use with this DVD/VCR, you should generally reduce the sharpness adjustment on your TV when viewing DVD video discs.

About

The icons on the heading bar show the playable discs for the function described under that heading.

: You can use this function with DVD video discs. : You can use this function with Video CDs. : You can use this function with Audio CDs and CD-R/RW CDs.

To pause playback (still mode)

Press PAUSE/STILL during playback.

To resume normal playback, press the PLAY button.

• The sound is muted during still mode.

To stop playback

Press ST OP.

Playing a Disc while the VCR section is recording or standing by for timer recording

1) Start to record. Follow steps 1~5 on page 34.

•If the DVD/VCR is standing by for recording, turn on

the DVD/VCR.

2) Press VCR DVD selector to select DVD mode. The DVD indicator will light.

3) Play a disc. Follow steps 3 ~ 5 on page 42.

•Press PLAY if the DVD/VCR does not start to play a

disc automatically.

4) Stop to play.

To remove the disc

Press OPEN/CLOSE.

Remove the disc after the disc tray opens completely.

Press STOP to stop play back a disc.

Screen saver function

The screen saver operates when you leave the unit in DVD stop mode for about five minutes. The screen will repeatedly get dark gradually and back to normal.

To turn off the PBC

Press number button 1 in the stop mode, then press ENTER.

Be sure to press the OPEN/CLOSE button to close the disc tray after you remove the disc.

Notes:

• If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen according to the type of loaded disc. In this case, check your disc again (See pages 8 and 61).

• Some discs may take a minute or so to start playback.

• When you set a single-faced disc label downwards (ie. the wrong way up) and press the OPEN/CLOSE button or the PLAY button on the unit, “Reading” will appear on the display for 30 seconds and then “Incorrect Disc” will continue to be displayed.

• Some discs may not work the resuming facility.

• Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC, see above.

• Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according to the disc contents the software producers designed, some playback features may not be available. Also refer to the instructions supplied with the DVDs.

• Do not move the DVD/VCR during playback. Doing so may damage the disc.

• Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may cause the DVD/VCR to malfunction.

• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD/VCR to malfunction.

• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the ON/STANDBY (I /

• There may be a slight delay between you pressing the button and the function activating.

) button on your remote control once the movie is completed.

Basic playback (DVD)

2C53301C (E)p42-45 21/4/04, 11:1243

Page 44

Basic playback (DVD)

Playing a disc (continued)

You can play discs at various speeds.

DVD VCD

Playing in fast reverse or fast forward directions

REW SKIP /

PLAY FWD

PAUSE/STILL

SLOW

Press REW or FWD during playback.

REW

FWD: Fast forward playback

REW: Fast reverse playback

FWD

Each time you press the REW or FWD button, the playback speed changes.

DVD

Playing frame by frame

VCD

Press PAUSE/STILL during still playback.

Each time you press the PAUSE/ STILL button, the picture advances one frame.

DVD

Playing in slow-motion

VCD

Press SLOW during playback.

SLOW

Each time you press the SLOW button, the slow-motion speed changes.

DVD VCD

Locating a chapter or track

To resume normal playback

Press PLAY.

PLAY

Notes:

• The DVD/VCR mutes sound and subtitles during reverse and forward scan of DVD video discs. However, the DVD/ VCR plays sound during fast forward or fast reverse play of audio CDs.

• The playback speed may differ depending on the disc.

T o resume normal playback

Press PLAY.

PLAY

Note:

The sound is muted during frame by frame playback.

To resume normal playback

Press PLAY.

PLAY

Note:

The sound is muted during slow-motion playback.

Press SKIP or repeatedly to display the chapter or track number you want.

Playback starts from the selected chapter or track.

INDEX

SKIP

To locate succeeding chapters or tracks.

INDEX

–

SKIP

Playback starts from the beginning of the current chapter or track. When you press twice in quick successions, playback starts from the beginning of the preceding chapter or track.

Notes:

• A “Prohibition” symbol may appear at the upper left of the screen. This symbol means either the feature you tried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate a problem with the DVD/ VCR.

• The unit is capable of holding a still video image or On screen display image on your television screen indefinitely. If you leave the still video image or On screen display image displayed on your TV for an extended period of time, you risk permanent damage to your television screen. Projection televisions are very susceptible.

2C53301C (E)p42-45 21/4/04, 11:1244

Page 45

Advanced playback (DVD)

7 9

654

321

PLAY

MP3/WMA/JPEG playback

This player can play back the MP3/WMA/JPEG-data which has been recorded on CD-R or CD-RW. To produce the MP3/WMA/JPEG-data, you need a Windows-PC with CD-ROM drive and a MP3/WMA/JPEG-encoding Software (not supplied). The Apple-HFS-System can not be played.

MP3/WMA playback

Press OPEN/CLOSE.

The disc tray will open. Place a disc on which MP3 or WMA files have been recorded onto the tray.

Press OPEN/CLOSE or PLAY.

The disc tray closes automatically. On the TV-screen,“Reading” will appear. Reading will take as much time as the

Reading

number of file.

PLAY

A file menu screen will appear on the TV screen.

Press

–

or to select folder.

SET

ENTER

–

SET

CD-R

Pops

Japan

Bay Bridge

CLOSE MY EYES

DIVE TO BLUE

Honey

BLUE EYES13Welcome party

Blurry Eyes14Thailand

Press / or / or Number keys to select the desired file, then press ENTER.

The file is selected and play commences.

SET

–

ENTER

SET

• In case the folder includes more than 15 tracks, press or to display

–

next file list.

CD-R

Pops

1 2 3 4 5 6 7

Japan

Bay Bridge

CLOSE MY EYES

DIVE TO BLUE

Honey BLUE EYES13Welcome party Blurry Eyes14Thailand

/0-9/Enter/Play Mode

/72

flower Lies and Truthwinter fall Rain Strawberry

--:--

CD-R

Pops

15 16

• When PLAY has been pressed after displaying the file menu, or when the disc tray has been closed after pressing PLAY in step 2, playback begins automatically starting from the first file. In this case, if the first file is an MP3/ WMA file, only MP3/WMA files are played back in order. If the first file is a JPEG file, the first JPEG file is played back.

9 10 11 12

/0-9/Enter/Play Mode

Mother

Hold Your Last

/0-9/Enter/Play Mode

/72

flower Lies and Truthwinter fall Rain Strawberry

/72

MP3/WMA/JPEG CD Information

Limitations on MP3/WMA/JPEG CD playback

• MP3/WMA/JPEG CD is the disc that is standardized by ISO9660, its file name must include 3-digits extension letters, “mp3”, ”wma”, “jpg”.

• The directory and file names of the MP3/WMA/JPEG CD must be correspond to the ISO standardized files.

• This unit can read 200 files per disc. If a disc has more than 200 files, it reads up to 200 files, the remaining files will be omitted.

• The unit is able to recognize up to a maximum of 50 directories per disc.

• MP3/WMA CDs cannot be used for playback for the purpose of recording.

• If the CD has both audio tracks and MP3/WMA/JPEG files, only audio tracks are played.

--:--

• It may take more than one minute for this unit to read MP3/ WMA/JPEG files depending on its structure.

• Music recorded by “Joliet Recording Specification” can be played back, the file name is displayed (within 16 letters) on the screen. Long file names will be condensed.

• The music files recorded by “Hierarchical File System” (HFS) cannot be played.

• The unit can play back baseline and progressive JPEG files.

Limitations on display

• The maximum number for display is 16 letters. Available letters for display are the following: capital or small alphabets of A through Z, numbers of 0 through 9, and _ (under score).

• Other letters than those above are replaced in hyphen.

Notes on MP3/WMA/JPEG files

--:--

To play back MP3/WMA/JPEG CD in the recorded order,

1. Use MP3/WMA/JPEG software that records data

alphabetically or numerically.

2. Name each file including two-digit or three-digit number

(e.g. “01” “02” or “001” “002”).

3. Refrain from making too many sub-folders.

WMA disc compatibility with this player is limited as follows:

1) Sampling Frequency: within 32 -- 48 kHz

2) Bit Rate: within 48 -- 192kbps. Mono WMA files and WMA files (under 48kbps) cannot be played back on this player.

CAUTION:

• Some MP3/WMA/JPEG CDs can not be played back depending on the recording conditions.

• The CD-R/RW that has no music data or non-MP3/WMA/ JPEG files can not be played back.

Press STOP to end playback.

• The unit records the stopped point. “ ” appears on the screen. Press PLAY to resume playback (from the scene point).

• If you press STOP again or unload the disc, the unit will clear the stopped point.

OPEN/CLOSE 0–9

PLAY STOP

ENTER ▲/ ▼/ /

Basic playback (DVD)

Advanced playback (DVD)

2C53301C (E)p42-45 21/4/04, 11:1345

Page 46

Advanced playback (DVD)

SET

–

ENTER

MP3/WMA/JPEG playback (continued)

You can select your desired JPEG file on the file menu and picture menu. The selected JPEG file is automatically adjusted to the TV screen. (When the aspect ratio of the JPEG file is different to your TV screen, the black bar will appear at the top and bottom, or the both sides of the TV screen.

JPEG CD playback

Press OPEN/CLOSE.

The disc tray will open. Place a disc on which JPEG files have been recorded onto the tray.

Press OPEN/CLOSE or PLAY.

PLAY

The disc tray closes automatically. On the TV-screen, “Reading” will appear. Reading will take as much time as the number of file.

Reading

Press ENTER.

Press STOP to end playback.

OPEN/CLOSE 0–9

SKIP

PLAY STOP

TOP MENU MENU ENTER ▲/ ▼/

The selected picture appears on the TV screen.

The file menu appears on the TV screen. If you want to watch the other file, repeat steps 4~5.

A file menu screen will appear on the TV screen. Press

Press / or / or Number keys to select the desired file.

or to select folder.

SET

–

ENTER

SET

–

7 9

CD-R

Collection

1 2 3 4 5 6 7

CD-R

Collection

321

654

2 3 4 5 6 7

To display a picture menu, press MENU. (To return to a file menu, press T OP MENU.) Press

TOP MENU

/ or / to select the desired file.

• To display next list, press SKIP

• When PLAY has been pressed after displaying the file menu, or when the disc tray has been closed after pressing PLA Y in step 2, playback begins automatically starting from the first file. In this case, if the first file is a JPEG file, the first JPEG file is played back. If the first file is an MP3/WMA file, only MP3/WMA files are played back in order.

Pic-1 Pic-2 Pic-3 Pic-4 Pic-5 Pic-6 Pic-7

Pic-1

Pic-2 Pic-3 Pic-4 Pic-5 Pic-6 Pic-7

Pic-8

Pic-9

Pic-10

Pic-11

Pic-12

Pic-13

Pic-14

/0-9/Enter/Play Mode/Menu

Pic-8

Pic-9

Pic-10

Pic-11

Pic-12

Pic-13

Pic-14

/0-9/Enter/Play Mode/Menu

or .

Notes:

• The picture menu is displayed when the FUJICOLOR CD or the Kodak Picture CD are played. To display the file menu

/36

press TOP MENU.

• During MP3/WMA/JPEG-Playback, you can not use SEARCH, A-B Repeat functions.

• You can use Repeat (Track or All), Random functions and Program playback for MP3/WMA/JPEG CD Playback. (See pages 52 and 53.)

• In the case of a CD containing a mixture of MP3, WMA and

/36

JPEG files, the files are played back by selecting them from the file menu.

File menu information

Media type

Operation

File number

Elapsed time

Folder

/Menu

: Indicates MP3 file : Indicates WMA file : Indicates JPEG file

Microsoft, Windows Media, and Windows Logo are trademarks or registered trademarks of Microsoft Corporation in both the United States and other countries.

2C53301C (E)p46-47 21/4/04, 11:1346

Page 47

Setting the JPEG Interval

VCR MENU

SETUP

SETUP ENTER

▲/ ▼/

You can continuously play back all JPEG files automatically. After the setting below, start playing the disc on which JPEG files have been recorded.

Press SETUP in the stop mode. Press or to select “Picture”, then press ENTER.

VCR MENU

SETUP

SET

–

ENTER

–

SET

Language Picture Parental OtherSound

/Enter/Setup/Return

To make SETUP screen disappear, press SETUP.

Press or to select “JPEG Interval”.

SET

–

ENTER

–

SET

Press ENTER or / to select your desired time.

Language Picture Parental OtherSound E.B.L.

Tv Screen Display JPEG Interval Select Files

Off

4:3

On Off All

/Enter/Setup/Return

SET

–

ENTER

–

SET

Language Picture Parental OtherSound E.B.L.

Tv Screen Display JPEG Interval Select Files

Off

4:3

On 5 Seconds All

/Enter/Setup/Return

Basic playback (DVD)

Advanced playback (DVD)

Off:

Plays back one file at a time.

5 Seconds:

Plays back images in the form of a slide show at 5 second intervals.

10 Seconds:

Plays back images in the form of a slide show at 10 second intervals.

15 Seconds:

Plays back images in the form of a slide show in 15 second intervals.

2C53301C (E)p46-47 21/4/04, 11:1347

Page 48

Advanced playback (DVD)

VCR MENU

SETUP

MP3/WMA/JPEG playback (continued)

SETUP ENTER

▲/ ▼/

Setting the Select Files

When playing back a CD containing a mixture of MP3, WMA and JPEG files, only MP3/WMA or JPEG files can be displayed on the file menu.

Press SETUP in the stop mode.

Press

or to select “Picture”, then press

ENTER.

VCR MENU

SETUP

SET

–

ENTER

SET

–

Language Pi ctur e Par enta l OtherSound

/Enter/Setu p/Re tur n

Press or to select “Select Files”.

SET

–

ENTER

SET

–

Language Pi ctur e Paren tal OtherSound E.B.L.

Tv Screen Display JPEG Interval Select Files

/Enter/Setu p/Re tur n

Press ENTER or / to select your desired

file type.

SET

–

ENTER

SET

–

Language Pi ctur e Paren tal OtherSound E.B.L.

Tv Screen Display JPEG Interval Select Files

/Enter/Setu p/Re tur n

All:

Displays all files.

Music Only:

Displays only MP3/WMA files.

Pictures Only:

Displays only JPEG files.

Off

4:3

On Off All

Off

4:3

On Off Pictures Only

To make SETUP screen disappear, press SETUP.

2C53301C (E)p48-49 21/4/04, 11:1348

Page 49

Zooming (JPEG CD)

CM SKIP

ZOOM

COUNTER RESET

ANGLE

ZOOM ▲/ ▼/ /

This unit will allow you to zoom in on the JPEG image.

Press ZOOM during playback.

CM SKIP

ZOOM

Off

Enlarged JPEG images are displayed. You can make the images even larger by repeatedly pressing ZOOM.

Changing angles (JPEG CD)

You can display JPEG images rotating at 90 degree intervals.

Press ANGLE during playback. Images are rotated 90 degrees to the right.

COUNTER RESET

ANGLE

Press / / / to view a different part of the frame.

SET

–

ENTER

–

SET

In the zoom mode press ZOOM repeatedly to return to a 1:1 view (

Press ANGLE repeatedly until the desired angle is selected.

Pressing ANGLE four times returns the image to its original angle.

You may move the frame from the

centre position to UP, DOWN, LEFT or RIGHT direction.

Off).

• Images are displayed at the same angle until the disc is removed.

Basic playback (DVD)

Advanced playback (DVD)

2C53301C (E)p48-49 21/4/04, 11:1349

Page 50

Advanced playback (DVD)

CM SKIP

ZOOM

DISPLAY

Zooming/Locating desired scene

0–9 ▲/ ▼/ /

JUMP ZOOM

ENTER CANCEL

DVD

Zooming

VCD

This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame.

Press ZOOM during playback.

CM SKIP

ZOOM

The centre part of the image will be zoomed in. Each press of ZOOM will change the ZOOM 1 (x 1.3), 2 (x 1.5) and 3

Press / / / to view a different part of the frame.

SET

–

ENTER

–

SET

You may move the frame from the

centre position to UP, DOWN, LEFT or RIGHT direction.

(x 2.0).

Notes:

•You can select the Pause, Slow or Search playback in the zoom mode.

•Some discs may not respond to zoom feature.

DVD VCD

Locating desired scene

In the zoom mode press ZOOM repeatedly to return to a 1:1 view ( Off).

Use the title, chapter and time recorded on the disc to locate the desired point to play back.

To check the title, chapter and time, press DISPLAY.

Press JUMP during playback or stop mode.

ZERO RETURN

JUMP

Jump Time

Title Chapter

/Enter/0 9/Cancel/Jump

Press Numbered buttons (0–9) to change the number.

• If you input a wrong number, press

7 9

321

654

CANCEL.

• Refer to the package supplied with

the disc to check the numbers.

Press or to select the “Time”, “Title” or “Chapter”.

Note:

In case of the Video-CD playback with PBC, the JUMP does not work. To turn off PBC, see page 43.

SET

–

ENTER

SET

–

Press ENTER. Playback starts.

SET

–

ENTER

SET

–

2C53301C (E)p50-53 21/4/04, 11:1350

• When you change the title, playback starts from Chapter 1 of the selected title.

• Some discs may not work in the above operation.

Page 51

Marking desired scenes

MARKER

The unit stores the points that you want to watch again up to 3 points. You can resume playback from each scene.

▲/▼

MARKER ENTER

CANCEL

DVD

Marking the scenes

VCD

Press MARKER during playback.

MARKER

Marker 1 Marker 2 Marker 3

/Enter/Cancel/Marker

Select the blank Marker using or . Then press ENTER at the desired scene.

• Repeat this procedure to set the other 2 scenes.

SET

–

ENTER

–

SET

Marker 1 Marker 2 Marker 3

/Enter/Cancel/Marker

Press MARKER to remove this display.

MARKER

2700 54

DVD

Returning to the scenes

VCD

Press MARKER during playback or stop mode.

Marker 1 Marker 2 Marker 3

/Enter/CancelMarker

Press or to select the Marker 1-3.

SET

–

ENTER

–

SET

Marker 1 Marker 2 Marker 3

/Enter/Cancel/Marker

Press ENTER.

SET

–

ENTER

–

SET

Playback starts from the marked

scene.

00 01

Basic playback (DVD)

54 25 31

Advanced playback (DVD)

Notes:

•

Some discs may not work with the marking operation.

•

The marking is canceled when you

open the disc tray or turn

the power off.

•

Some subtitles recorded around the marker may fail to appear.

2C53301C (E)p50-53 21/4/04, 11:1351

To cancel the Marker

Follow the above steps 1~2, then press CANCEL.

Page 52

Advanced playback (DVD)

A-B RPT

Repeat playback/A-B Repeat playback

PLAY MODE A-B RPT

ENTER ▼/

DVD VCD

Repeat playback of Title, Chapter and T rack

Press PLAY MODE during playback or stop mode.

SP/SLP

PLAY MODE

DVD Press

“Chapter” or “Title”.

SET

–

ENTER

SET

/ or ENTER once or twice to select

–

Repeat

/Enter/Play Mode

Off

Repeat

/Enter/Play Mode

Chapter

CD/VCD Press Press

to select “Repeat”. / or ENTER once or twice to select

“Track” or “All”.

SET

Play Mode Off

–

ENTER

Repeat Of f

–

SET

/Enter/Play Mode

Play Mode Off Repeat::

/Enter/Play Mode

Track

Repeat

/Enter/Play Mode

Play Mode Off Repeat

/Enter/Play Mode

DVD VCD

A-B Repeat playback

A-B repeat playback allows you to repeat material between two selected points.

Press A-B RPT during playback.

Title

The start point is selected.

Press A-B RPT again.

The end point is selected. Playback starts at the point that you selected. Playback stops at the end point, returns to Point A automatically, then starts again.

All

A B

Press PLAY MODE again to make the screen disappear.

Press PLAY to start Repeat playback. To resume normal playback, select Repeat “Off”.

Notes:

Some discs may not work with the repeat operation.

2C53301C (E)p50-53 21/4/04, 11:1452

To resume normal playback

Press A-B RPT again.

“

Notes:

• In A-B repeat mode, subtitles near point A or B may not appear.

• A-B Repeat playback is not available in multi-angle scenes.

• A-B Repeat playback does not work when Repeat playback is on.

• You may not be able to set A-B Repeat, depending on the scenes of the DVD.

• A-B repeat does not work with an interactive DVD, MP3/ WMA/JPEG CD and Video CD with PBC.

” appears on the screen.

Off

Page 53

Program playback/Random playback (CD)

Clear Program Playback

2 3 5 8 11 3 1

1 6 9 12

1 7

4 7 10

Repeat

Off

Play Mode

Program

/Enter/0 9/Cancel/Play Mode

You can arrange the order of tracks on the disc.

0–9 PLAY MODE

PLA Y

VCD

Program playback

Press PLAY MODE in the stop mode.

SP/SLP

PLAY MODE

Play Mode Repeat Off

::Off

/Enter/Play Mode

Press or to select Play Mode, then press

/ or to select “Program”.

SET

–

ENTER

SET

–

Play Mode Repeat

Clear Program Playback

/Enter/0 9/Cancel/Play Mode

Press / or / to select the programming position. Use Numbered buttons (0–9) to input

the Track numbers.

SET

–

ENTER

SET

7 9

–

• To program others, repeat Step 3.

• If you input a wrong number, press

CANCEL.

Play Mode Repeat

1 9

321

654

4 7 10 2 3 5 8 11 3 1

1 6 9 12

Clear

/Enter/0 9/Cancel/Play Mode

Program Playback

Program

Off

7 8 9

Program

Off

▲/ ▼/

ENTER CANCEL

Press / or / to select “Program Playback”

SET

–

ENTER

SET

10 11 12

and press ENTER.

–

The programmes you selected will start to playback in the order.

To return to normal playback, select Play Mode: “Off”.

Basic playback (DVD)

To cancel program playback Select “Clear” and press ENTER.

SET

–

ENTER

–

SET

• The program is canceled when you open the disc tray or turn the

power off.

Note:

In playing back the Video CD with PBC, you can not set Program playback.

Advanced playback (DVD)

2C53301C (E)p50-53 21/4/04, 11:1453

VCD

Random playback

Press PLAY MODE in the stop mode.

SP/SLP

PLAY MODE

Press / to select Play Mode, then press

/ to select “Random”.

SET

–

ENTER

SET

–

Play Mode Repeat

/Enter/Play Mode

Random

Off

Press PLAY

PLAY

The Random Playback will start.

Note:

In playing back the Video CD with PBC, you can not set Random playback.

Page 54

Advanced playback (DVD)

COUNTER RESET

ANGLE

Changing angles/Title selection/DVD menu

Changing angles

ANGLE PLAY

TOP MENU MENU

ENTER ▲/ ▼/

When playing back a disc recorded with multi-angle facility,

Press ANGLE during playback.

COUNTER RESET

ANGLE

The current angle will appear.

1/9

you can change the angle that you are viewing the scene from.

Press ANGLE repeatedly until the desired angle is selected.

Note:

Depending on the DVD, you may not be able to change the angles even if multi-angles are recorded on the DVD.

Title selection

Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title.

Press TOP MENU during playback.

TOP MENU

Title menu appears on the screen.

Press / or / to select the desired title.

SET

–

ENTER

SET

–

Press ENTER or PLAY.

Note:

Depending on the DVD, you may not be able to select the title. Depending on the DVD, a “title menu” may simply be called a “menu” or “title” in the instructions supplied with the disc.

SET

–

ENTER

–

SET

The playback of the selected title will start.

PLAY

DVD menu

Some DVDs allow you to select the disc contents using the menu. When you play back these DVDs, you can select the subtitle language and sound-track language, etc. using the menu.

Press MENU during playback.

The DVD menu appears on the screen.

• Press MENU again to resume playback at the scene when you pressed MENU.

Press / or / to select the desired item.

SET

–

ENTER

–

SET

2C53301C (E)p54-57 21/4/04, 11:1454

Press ENTER.

Note:

Depending on the DVD, you may not be able to resume playback from the scene point when you pressed MENU.

SET

–

ENTER

–

SET

The menu continues to another screen. Repeat steps 2 and 3 to set

the item completely.

Page 55

Function setup (DVD)

Changing soundtrack language/ Setting surround sound

DVD

Changing soundtrack language

VCD

You can select the language when you play a multilingual disc.

Press AUDIO during playback.

AUDIO SELECT

AUDIO

Press AUDIO repeatedly until the desired language is selected.

AUDIO SELECT

AUDIO

The current soundtrack language will appear.

2/8 Fra Dolby Digital

Spatializer Off

The on-screen display will disappear after a few seconds.

1/8 Eng Dolby Digital

Spatializer Off

Audio type changes as follows each time you press AUDIO.

Notes:

• If the desired language is not heard after pressing the

• Changing soundtrack language is cancelled when you

AUDIO

In case of Video CD playback

Spatializer Off

button several times, the language is not recorded on the disc.

open the disc tray. The initial default language or available language will be heard if the disc is played back again.

Spatializer Off

DVD VCD

Setting surround sound

This DVD/VCR equipped with a “SP ATIALIZER VIRTUAL SURROUND”. It can produce the effect of being in a cinema or a concert hall.

During disc playback press AUDIO.

AUDIO SELECT

AUDIO

1/8 Eng Dolby Digital

Spatializer Off

To cancel Surround mode: Follow the left steps 1~2, then press “Off” position.

Note:

The “SPATIALIZER VIRTUAL SURROUND” is effective only for the sound of disc.

or to select the

Press or to select “On”.

SET

–

ENTER

SET

–

1/8 Eng Dolby Digital

Spatializer On

Spatializer® 3-Dimensional Sound Processing provided by Desper Products. Inc. Certain audio features of this product manufactured under a license from Desper Products, Inc., Spatializer® and the circle-in-square device are trademarks owned by Desper Products, Inc.

Advanced playback (DVD)

Function setup (DVD)

2C53301C (E)p54-57 21/4/04, 11:1455

Page 56

Function setup (DVD)

Setting subtitles/Karaoke playback

Turning the subtitles on and off

When playing back a disc recorded with subtitles, you can turn the subtitles on or off.

Press SUBTITLE during playback until “Off” appears.

ATR

SUBTITLE

Off

Changing the subtitle language

Y ou can select the language when playing back a disc recorded with multi-lingual subtitles.

Press SUBTITLE repeatedly during playback until your desired language appears.

ATR

SUBTITLE

1/32 Eng

The on-screen display will disappear after a few seconds.

Note:

Depending on the DVD, you may not be able to turn the subtitles on even if they are recorded on it. Depending on the DVD, you may not be able to turn the subtitles off.

Notes:

• Changing subtitle language is cancelled when you open the disc tray.

• Depending on the DVD, you may not be able to change the subtitles even if multilingual subtitles are recorded on it. While playing the DVD, the subtitle may change when: -you open or close the disc tray -you change the title.

• In some cases, the subtitle language is not changed to the selected one immediately.

SUBTITLE AUDIO

▲/ ▼/ /

Karaoke playback

You can turn the vocal on or off recorded on the DVD KARAOKE.

During DVD KARAOKE disc playback, press AUDIO.

AUDIO SELECT

AUDIO

Press ▲ or ▼ until the KARAOKE symbol ( ) appears.

• If you play non-Karaoke disc, the KARAOKE

–

Press

–

symbol (

SET

ENTER

SET

ENTER

SET

) does not appear.

–

or to select “On” or “Off”.

–

On : The primary vocal is output

Off : The primary vocal is not output.

1/8 Eng Dolby Digital

Spatializer Off

1/8 Eng Dolby Digital

Off

when it is recorded on the disc.

Notes:

• The vocal output feature is used during playback of Dolby Digital (multi-channel) recorded DVD KARAOKE discs. This feature allows you to turn off vocal audio tracks, or restore them for background accompaniment.

• When playing Karaoke, connect appropriate audio equipment such as an amplifier to the DVD/VCR.

2C53301C (E)p54-57 21/4/04, 11:1456

Page 57

E.B.L. (Enhanced Black Level)

VCR MENU

SETUP

RETURN

To select the black level of playback pictures, set your preference and monitor’s ability.

Setting E.B.L.

SETUP RETURN

ENTER ▲/ ▼/

Press SETUP in the stop mode or No Disc.

Press

VCR MENU

–

or to select “Picture”.

SETUP

SET

ENTER

–

SET

Language Picture Parental OtherSound

/Enter/Setup/Return

Press or ENTER, then press or to select “E.B.L.”.

SET

–

ENTER

SET

–

Language Picture Parental OtherSound E.B.L.

Tv Screen Display JPEG Interval Select Files

Off

4:3

On Off All

/Enter/Setup/Return

Press / or ENTER to select “On” or “Off”.

SET

CH – CH

ENTER

–

SET

Language Picture Parental OtherSound E.B.L.

Tv Screen Display JPEG Interval Select Files

4:3

On Off All

/Enter/Setup/Return

To make SETUP screen disappear, press SETUP o

r RETURN while the SETUP screen is being dis-

played.

Advanced playback (DVD)

Function setup (DVD)

On: Enhanced grey scale (0 IRE cut off) Off: Standard grey scale (7.5 IRE cut off)

2C53301C (E)p54-57 21/4/04, 11:1457

Page 58

Function setup (DVD)

VCR MENU

SETUP

RETURN

Setting the aspect ratio of TV screen

You can select the aspect ratio for your TV. The following pages describe the setup/operation in DVD mode.

Setting the aspect ratio of TV screen

SETUP RETURN

ENTER ▲/ ▼/

Press SETUP in the stop mode or No Disc.

Press

VCR MENU

–

or to select “Picture”.

SETUP

SET

ENTER

–

SET

Language Picture Parental OtherSound

/Enter/Setup/Return

Press or ENTER, then press or to select “Tv Screen”.

SET

–

ENTER

SET

–

Language Picture Parental OtherSound E.B.L.

Tv Screen Display JPEG Interval Select Files

Off

4:3

On Off All

/Enter/Setup/Return

Press or ENTER.

Press or to select your desired screen type, then press ENTER.

SET

–

ENTER

SET

–

Language Picture Parental OtherSound E.B.L.

Tv Screen Display JPEG Interval Select Files

Off On

Off All

/Enter/Setup/Return

4:34:3 4:3

16:9

You have the following screen sizes to choose from:

4:3

Letter box:

Select this mode when connecting to a conventional TV. When playing back a wide screen-DVD disc, it displays the wide picture with black bands at the top and bottom of screen.

4:3

Pan scan:

It displays the wide picture on the whole screen with left and right edges automatically cut off.

16:9

Wide:

Select this mode when connecting to a wide-screen TV. A wide screen picture is displayed full size.

T o make SETUP screen disappear , press SETUP or RETURN while the SETUP screen is being dis-

played.

Note:

If the DVD disc is not formatted in the pan & scan style, it displays 4:3 style.

2C53301C (E)p58-61 21/4/04, 11:1558

Page 59

Tv Screen Display

Off

/Enter/Setup/Return

Language Picture Parental OtherSound

JPEG Interval Select Files

All

Off

4:3

Off

E.B.L.

VCR MENU

SETUP

RETURN

Setting on screen display/Status display of disc

Setting on screen display

On screen display can be switched on or off when you press the buttons.

DISPLAY

SETUP RETURN

ENTER ▲/ ▼/ /

Press SETUP in the stop mode or No Disc.

Press

VCR MENU

–

or to select “Picture”.

SETUP

SET

ENTER

–

SET

Language Picture Parental OtherSound

/Enter/Setup/Return

Press or ENTER, then press or to select “Display”.

SET

–

ENTER

DVD VCD

Status display of disc

–

SET

Language Picture Parental OtherSound E.B.L.

Tv Screen Display JPEG Interval Select Files

Off

4:3

On Off All

/Enter/Setup/Return

Press

–

/ or ENTER to select “On” or “Off”.

SET

ENTER

–

SET

On: On screen displays appear when you press

the buttons (factory setting).

Off: On screen displays do not appear when you

press any buttons.

To make SETUP screen disappear, press SETUP or RETURN while the SETUP screen is being displayed.

Function setup (DVD)

Each press of DISPLA Y, the status display of the disc will appear on the screen and change as follows.

DVD

00:34:56 01:12:33 00:34:56 01 :12:33

Title 1/99

1/8

Eng DolbyDi gital

1/32

Eng

Chapter 1/999

To make status display disappear, press DISPLAY again.

2C53301C (E)p58-61 21/4/04, 11:1559

Video CD

00:12 04:32

1/9

Audio CD

Track 11/99

34:56 71:33

PBC

Track -/-

00:12 04:32

When you playback the CD disc, the status display will appear on the screen and continue displaying.

Page 60

VCR MENU

SETUP

RETURN

Function setup (DVD)

Dynamic Range Control

DRC (Dynamic Range Control) enables you to control the dynamic range so as to achieve a suitable sound for your equipment.

Dynamic Range Control

SETUP RETURN

ENTER ▲/ ▼/ /

Press SETUP in the stop mode.

Press

VCR MENU

SETUP

–

or to select “Sound”.

SET

ENTER

–

SET

Language Picture Parental OtherSound

/Enter/Setup/Return

Press or ENTER to select “Dialogue”.

SET

–

ENTER

–

SET

Press or ENTER, then press or to select desired setting.

SET

–

ENTER

–

SET

Language Picture Parental OtherSound Dialogue

Off

/Enter/Setup/Return

Off

On : DRC(TV) Off : DRC(Std)

To make SETUP screen disappear , press SETUP or RETURN while the SETUP screen is being

displayed.

Notes:

• This function works only during playback of Dolby Digital

recorded discs.

• The level of Dynamic Range Reduction may differ

depending on DVD video disc.

/Enter/Setup/Return

On: Loud sound such as explosion or the

like is toned down slightly when played back. This makes it suitable for when it is connected to a stereo.

Off: It plays back at the recording level on the

disc.

2C53301C (E)p58-61 21/4/04, 11:1560

Page 61

Parental control setting

Password Parental

0 9/Cancel

/Enter/Setup/Return

Language Picture Parental OtherSound

VCR MENU

SETUP

RETURN

Some discs are specified not suitable for children. Such discs can be limited not to play back with the unit.

0–9

Parental control setting

Press SETUP in the stop mode or No Disc. Press

VCR MENU

SETUP

–

Press or to select “Parental”, then press

–

or to select “Parental”. Then press

or ENTER.

Language

Picture Parental Other

Sound

SET

ENTER

SET

Password Parental

–

0 9/Cancel

Off

/Enter/Setup/Return

or until the level you require appears.

SET

ENTER

SET

–

Language Picture Parental OtherSound Password

Parental

▲/ ▼/ SETUP RETURN ENTER

CANCEL

Press ENTER to store the password.

SET

–

ENTER

–

SET

Note: Now the rating is locked and the setting cannot be changed unless you enter the correct password.

Press SETUP or RETURN to remove the parental control screen.

/Enter/Setup/Return

• Level Off:

The parental control setting does not function.

• Level 8: All DVD software can be played back.

• Level 1: DVD software for adults cannot be played

back.

• Select from the level 1 to level 8. The limitation will be more severe as the level number is lower.

Press or to select “Password”. Press number buttons (0-9) to input a 4-digit password.

SET

–

ENTER

SET

7 9

–

321

654

Be sure to remember this number!

Language Picture Parental OtherSound Password

Parental

0 9/Cancel

1234

/Enter/Setup/Return

• If you input a wrong number, press CANCEL.

Notes:

• If each setup (pages 57~66) has been completed, the unit can always be worked under the same conditions (especially with DVD discs). Each setup will be retained in the memory if you turn the power off.

• Depending on the discs, the unit cannot limit playback.

• Some discs may not be encoded with specific rating level information though its disc jacket says “adult.” For those discs, the age restriction will not work.

Function setup (DVD)

2C53301C (E)p58-61 21/4/04, 11:1561

Page 62

Function setup (DVD)

VCR MENU

SETUP

RETURN

To change the parental level

Press SETUP in the stop

Press Then press

VCR MENU

SETUP

–

or to select “Parental”.

or ENTER.

SET

ENTER

–

SET

Press number buttons (0–9) to enter the password you have stored.

321

654

7 9

mode or No Disc.

Language Pictur e Pa re nt al OtherSound Password

Parental

0 9/Cancel

Language Pictur e Pa re nt al OtherSound Password

Parental

0 9/Cancel

/Enter/Setup/ Re tu rn

123 4

/Enter/Setup/ Re tu rn

OPEN/CLOSE 0–9

SETUP RETURN

ENTER ▲/ ▼/

Press or to select “Password”, then press number buttons (0–9) to enter the password.

SET

–

ENTER

SET

7 9

–

321

654

Note: You can change the password if you want.

Language Picture Parental OtherSound Password

Parental

0 9/Cancel

9 8 7 6

/Enter/Setup/Return

Press ENTER.

SET

–

ENTER

–

SET

Now the parental level is changed and locked.

Language Picture Parental OtherSound Password

Parental

0 9/Cancel

/Enter/Setup/Return

Press ENTER.

SET

–

ENTER

SET

The rating is now unlocked.

–

Press or to select “Parental”, then press

or to change the parental level.

SET

–

ENTER

SET

–

2C53301C (E)p62-67 21/4/04, 11:1562

Language Pictur e Pa re nt al OtherSound Password

Parental

0 9/Cancel

Language Pictur e Pa re nt al OtherSound Password

Parental

/Enter/Setup/ Re tu rn

Press SETUP or RETURN to remove the parental control screen.

If you forget the password...

1. Press OPEN/CLOSE to open the disc tray.

2. Remove the disc.

3. Press OPEN/CLOSE again to close the disc tray. “No Disc” appears on the screen.

4. While holding 7 down on the remote control, press STOP on the front panel. “PASSWORD CLEAR” appears on the screen.

5. Enter a new password again.

Page 63

Temporary disabling of rating level by DVD disc

Please enter the 4 digit password

Cancel

/ReturnEnter/0

Depending on the DVD disc, the disc may try to temporarily cancel the rating level that you have set. It is up to you to decide whether to cancel the rating level or not.

Temporary disabling of rating level by DVD disc

OPEN/CLOSE 0–9

PLA Y ▲/▼

RETURN ENTER

Load a DVD disc and press PLAY or OPEN/ CLOSE on the unit (see page 42).

PLAY

If the DVD disc has been designed to temporarily cancel the Rating level, the screen which follows

the “Reading” screen will change, depending on which disc is played. If you select “YES” with the ENTER key, “Your disc exceeds the parental control level#.” screen will then appear.

Reading

Your disc exceeds the parental control level#.

Parental Control Level Cancel Picture

/Enter/Return

If you wish to cancel the set rating level temporarily, select “Parental Control Level” with

press ENTER. If the 4-digit password at step 2 on

or , then

page 62 has been set, the password entering screen will appear as shown in step 4. Alternatively, if the password has not been set, playback will commence. If you don’t know (or have forgotten) the password, select “Cancel Picture”. The setting screen will disappear. Press OPEN/ CLOSE to remove the disc.

Enter the password with number buttons (0–9). Then press ENTER.

If you interrupt the entering, press

321

RETURN.

654

7 9

SET

–

ENTER

SET

RETURN

–

Playback will commence if the entered password was correct.

Note:

This temporary cancellation of rating level will be kept until the disc is ejected. When the disc is ejected, the original rating level will be set again automatically.

Function setup (DVD)

SET

–

2C53301C (E)p62-67 21/4/04, 11:1563

ENTER

SET

–

Page 64

Function setup (DVD)

VCR MENU

SETUP

RETURN

Setting OSD language

The setup language can be selected.

DVD VCD

Setting OSD language

SETUP

RETURN ENTER

▲/ ▼/

Press SETUP in the stop mode or NO DISC.

Press

VCR MENU

SETUP

–

or to select “Other”.

SET

ENTER

–

SET

Picture ParentalSound

Language Other

/Enter/Setup/Return

Press or ENTER to select “OSD Language”.

SET

–

ENTER

–

SET

Language

Picture ParentalSound

OSD Language English

/Enter/Setup/Return

Press or ENTER and then press or to select desired language (e.g. English), then

press ENTER.

To make SETUP screen disappear , press SETUP or RETURN while the SETUP screen is being

displayed.

If the unit does not operate properly: Static electricity,

etc., may affect the player's operation. Disconnect the AC power cord once, then connect it again.

Other

SET

–

ENTER

–

SET

2C53301C (E)p62-67 21/4/04, 11:1664

Language

Picture ParentalSound

OSD Language English English

/Enter/Setup/Return

Francais Espanol

Other

Page 65

Setting language

VCR MENU

SETUP

RETURN

You can select the language of “Menu”, “Subtitle” and “Audio” if their languages are recorded onto the disc more than one language.

Setting language

SETUP RETURN

ENTER ▲ / ▼ /

Press SETUP in the stop mode or No Disc.

Press

VCR MENU

SETUP

–

or to select “Language”.

SET

ENTER

–

SET

Language Picture Parental OtherSound

/Enter/Setup/Return

Press or ENTER, then press or to select desired langugage item.

SET

–

ENTER

SET

–

Language Picture Parental OtherSound Menu

Subtitle Audio

English

Automatic

English

/Enter/Setup/Return

Press or ENTER.

Press

or to select your desired language,

then press ENTER.

SET

–

ENTER

–

SET

Language Picture Parental OtherSound

Menu Subtitle Audio

English

Automatic

English

English Francais Espanol

Other

To make SETUP screen disappear , press SETUP or RETURN while the SETUP screen is being

displayed.

Note:

If the selected language is not recorded on the disc, the firstpriority language is selected.

Function setup (DVD)

English, Francais, Espanol:

The selected language will be heard or seen.

Other:

Other language can be selected (see “Language code list” on page 67).

Original: (Audio)

The unit will select the first priority language of each disc.

Automatic: (Subtitle)

• The unit will automatically select the

the AUDIO setting.

• When the unit selects the same language as the the subtitles will not appear during playback.

• When you do not use the same language as the subtitles will appear during playback.

Off: (Subtitle)

Subtitles do not appear.

2C53301C (E)p62-67 21/4/04, 11:1665

/Enter/Setup/Return

same language in

AUDIO,

the AUDIO,

Page 66

Function setup (DVD)

Selecting PROGRESSIVE scan

The progressive scan capability provides the highest resolution pictures with less flicker and line structure. If you are using the Component video jacks, but are connecting the DVD/VCR to a standard (analog) television, set PROGRESSIVE to Off. If you are using the Component video jacks for connection to a TV or monitor that is compatible with a progressive scan signal, set PROGRESSIVE to On.

DVD VCD

Selecting PROGRESSIVE scan

VCR DVD

1 2

Preparation:

• Connect to a TV equipped with component jacks.

• Turn ON the TV and set it to the corresponding video input mode.

• Set the S-VIDEO/COMPONENT video selector switch on the rear panel to COMPONENT position.

• Press VCR DVD selector to select the DVD mode. (The DVD indicator will light.)

Press PROGRESSIVE in the stop mode.

INPUT SELECT

PROGESSIVE

Press PLAY to start playback.

The progressive indicator “ display window will light.

• The unit recognizes the picture source (film or video) of the current disc according to the disc information.

” on the

PLAY

To select PROGRESSIVE scan Off

Press PROGRESSIVE in the stop mode. The progressive indicator “ go off.

” on the display window will

There are two types of source content in pictures recorded in DVD video discs: film content (pictures recorded from films at 24 frames per second) and video content (video signals recorded at 30 frames per second).

When the unit plays back a film source material, uninterlaced progressive output signals are created using the original information. When a video content is played back, the unit interleaves lines between the interlaced lines on each to create the interpolated picture and outputs as the progressive signal.

Notes:

• Some discs may not be played back with the progressive scanning mode correctly because of the disc characteristics or recording condition.

• If your TV does not accept the progressive scan format, the picture will appear scrambled if you select progressive scan output from the unit. In such a case, select PROGRESSIVE scan Off.

• Once PROGRESSIVE scan On, all other video outputs are disabled except component video outputs.

• You cannot make the progressive scanning mode active in following cases. – The unit is in the VCR mode. – The disc is played back in the DVD mode. – The S-VIDEO/COMPONENT video selector switch is set to

S-VIDEO position.

2C53301C (E)p62-67 21/4/04, 11:1666

Page 67

Others

Language code list

Enter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio” (see pages 65).

Language Name Code Language Name Code Language Name Code Language Name Code Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919 Afar 1111 Finnish 1619 Lithuanian 2230 Slovak 2921 Afrikaans 1116 French 1628 Macedonian 2321 Slovenian 2922 Albanian 2927 Frisian 1635 Malagasy 2317 Somali 2925 Amharic 1123 Galician 1722 Malay 2329 Spanish 1529 Arabic 1128 Georgian 2111 Malayalam 2322 Sundanese 2931 Armenian 1835 German 1415 Maltese 2330 Swahili 2933 Assamese 1129 Greek 1522 Maori 2319 Swedish 2932 Aymara 1135 Greenlandic 2122 Marathi 2328 Tagalog 3022 Azerbaijani 1136 Guarani 1724 Moldavian 2325 Tajik 3017 Bashkir 1211 Gujarati 1731 Mongolian 2324 Tamil 3011 Basque 1531 Hausa 1811 Nauru 2411 Tatar 3030 Bengali; Bangla 1224 Hebrew 1933 Nepali 2415 Telugu 3015 Bhutani 1436 Hindi 1819 Norwegian 2425 Thai 3018 Bihari 1218 Hungarian 1831 Oriya 2528 Tibetan 1225 Breton 1228 Icelandic 1929 Panjabi 2611 Tigrinya 3019 Bulgarian 1217 Indonesian 1924 Pashto, Pushto 2629 Tonga 3025 Burmese 2335 Interlingua 1911 Persian 1611 Turkish 3028 Byelorussian 1215 Irish 1711 Polish 2622 Turkmen 3021 Cambodian 2123 Italian 1930 Portuguese 2630 Twi 3033 Catalan 1311 Japanese 2011 Quechua 2731 Ukrainian 3121 Chinese 3618 Javanese 2033 Rhaeto-Romance2823 Urdu 3128 Corsican 1325 Kannada 2124 Romanian 2825 Uzbek 3136 Croatian 1828 Kashmiri 2129 Russian 2831 Vietnamese 3219 Czech 1329 Kazakh 2121 Samoan 2923 Volapük 3225 Danish 1411 Kirghiz 2135 Sanskrit 2911 Welsh 1335 Dutch 2422 Korean 2125 Scots Gaelic 1714 Wolof 3325 English 1524 Kurdish 2131 Serbian 2928 Xhosa 3418 Esperanto 1525 Laothian 2225 Serbo-Croatian 2918 Yiddish 2019

Function setup (DVD)

Others

Estonian 1530 Latin 2211 Shona 2924 Yoruba 3525 Faroese 1625 Latvian, Lettish 2232 Sindhi 2914 Zulu 3631

2C53301C (E)p62-67 21/4/04, 11:1667

Page 68

Others

Troubleshooting

Check the following guide for the possible cause of a problem before contacting service.

SYMPTOMS POSSIBLE SOLUTIONS

PAGE

DVD/VCR

DVD/VCR does not operate.

No picture.

No sound.

The remote control does not function.

No CATV reception.

• Make sure the power cord is plugged in.

• Try another AC outlet.

• Power is off, check fuse or circuit breaker.

• Unplug unit, then plug it back in.

• Select the DVD or VCR mode before operating.

• Antenna connection is not correct or antenna cable is disconnected.

• The video channel is not in the correct position or the TV is not set to the video channel 3 or 4.

• Check the unit is connected correctly.

• The video input selector of the TV is not set to VIDEO. Set to VIDEO (or equivalent).

• Channel is set to the external mode.

• Check the unit is connected correctly.

• Check the input selector of the amplifier is set properly.

• The unit is in the Special playback mode.

• Aim the remote control at the remote sensor.

• Operate within Approx. 7 Meters or reduce the light in the room.

• Clear the path of the beam.

• The batteries are weak. Replace the batteries.

• Check the batteries are inserted correctly.

• Check all CATV connections.

• Station or CATV system problems, try another station.

5 – – 5

30,42

14~17

14~19

–

14~19

–

31,44

16,17

VCR

TV recording does not work. 29,34

Timer recording does not work.

Noise bars on screen.

• The erase prevention tab of the video cassette is broken off.

• The unit is in the external input mode.

• The time is not set correctly.

• The recording start/end time is not set correctly.

• The TIMER REC has not been pressed (

• Tracking adjustment beyond range of automatic tracking circuit. Try Manual tracking adjustment.

• Video heads are dirty.

• The tape is worn or damaged.

is not lit).

24 37 37

–

DVD

• Select proper language in the menu options.Display is not shown in your language. 64

Playback doesn’t start.

Stopping playback, slow-motion play, repeat play, or memory play, etc. cannot be performed.

No picture, or the screen is blurred or divided into two parts.

No 4:3 (16:9) picture. • The setup does not match your TV.

No on-screen display. • Select Display “On”.

No surround sound. • The setup does not match your stereo system.

The unit or remote operation key is not functioning.

Playback does not start when the title is selected.

Audio soundtrack and/or subtitle language is not changed when you play back a DVD.

No subtitle.

Angle cannot be changed.

appears on the screen.

• No disc is inserted.

• The disc may be dirty. Clean up the disc.

• The unit cannot play DVD-ROMs, etc.

• Some discs may not do some of the functions.

• The S-VIDEO/COMPONENT selector is not set correctly.

• The PROGRESSIVE scan is On through the unit is connected to a TV via the VIDEO OUT or the S-VIDEO OUT jack.

• Turn off the unit and unplug the AC power cord for several minutes, then replug it.

• Check the Parental setup.

• Multilingual language is not recorded on the DVD disc.

• Some discs have no subtitles.

• Subtitles are cleared. Press SUB TITLE.

• Multi-angles are not recorded on the DVD disc.

• The function is prohibited with the unit or the disc.

6 8

–

19 66

–

61,62

2C53301C (E)p68-BACK 12/2/04, 2:32 PM68

Page 69

Specifications

General

Power supply Power consumption Weight Dimensions

Tuner

Antenna input/output RF channel output Color system Video head Audio track Hi-Fi frequency response Hi-Fi dynamic range F.FWD/REW time at 25˚C (77˚F) Applicable disc Frequency range S/N ratio Harmonic distortion Wow and flutter Operating conditions

Input/Output

DVD/VCR

Video input 1.0 V (p-p), 75 Ω, negative sync., pin jack x 2 Video output 1.0 V (p-p), 75 Ω, negative sync., pin jack x 1 Audio input –8 dBm, 50 kΩ, negative sync., pin jack (L/R) x 2 Audio output –8 dBm, 1 kΩ, negative sync., pin jack (L/R) x 1

DVD

S-video output (Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin × 1

Component video output (Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack × 1

Audio output (BITSTREAM/PCM 0.5 V (p-p), 75 Ω, pin jack × 1 COAXIAL)

Audio output (BITSTREAM/PCM Optical connector × 1 OPTICAL)

Audio output (ANALOG) –12 dB, 1 kΩ, pin jacks (L, R) × 1 S-VIDEO/COMPONENT video selector Slide switch × 1

AC 120 V 60 Hz Operation: 18 W, Stand by: 2 W

7.9 lbs (3.6 kg)

Width: 16-15/16 inches (430 mm) Height: 3-7/8 inches (99 mm) Depth: 9-13/16 inches (250.5 mm) 181 channel freq. synthesized VHF 2-13 UHF 14-69 CATV 125 Channels UHF/VHF In/Out: 75 Ω coaxial Channel 3 or 4, Switchable NTSC 4 Rotary heads Hi-Fi sound - 2 Tracks / MONO sound - 1 Track 20 Hz to 20,000 Hz More than 90dB Approx. 1 minute and 48 seconds (with T-120 Cassette Tape) DVD (12 cm, 8 cm), CD (12 cm, 8 cm) DVD: 4 Hz-22 kHz, CD: 4 Hz-20 kHz 90dB (DVD)

0.02% (DVD)

Less than 0.01% Wrms Temperature: 5˚C-40˚C (41˚F-104˚F), Operating status: Horizontal

B)/(PR) 0.7 V (p-p), 75 Ω, pin jack × 2

Others

Supplied accessories

Audio/video cable ................................................. 1

Remote control (SE-R0108) ................................. 1

Batteries (R03/AAA) ............................................. 2

75 ohm coaxial cable ............................................ 1

• Designs and specifications are subject to change without notice.

2C53301C (E)p68-BACK 12/2/04, 2:32 PM69

Page 70

Others

Limited warranty

2C53301C (E)p68-BACK 12/2/04, 2:32 PM70

Page 71

2C53301C (E)p68-BACK 12/2/04, 2:32 PM71

Others

Page 72

2C53301C (E)p68-BACK 12/2/04, 2:32 PM72

Printed in Thailand04/03 U

Page 73

REPRODUCTOR DE DVD & VIDEOGRABADOR DE CASSETTE

SD-V392

Referencìa rápida

DIG ITAL VIDEO

PRECAUCION

RIESGO DE DESCARGA

ELECTRICA NO ABRIR

A VISO:

ADVERTENCIA: Este equipo ha sido sometido a pruebas y cumple con los límites establecidos para un aparato digital

PARA REDUCIR EL RIESGO DE DESCARGA ELECTRICA, NO RETIRE LA CUBIERTA (O POSTERIOR). EN EL INTERIOR DEL APARATO NO HAY COMPONENTE ALGUNO QUE PRECISE SERVICIO DE MANTENIMIENTO A CARGO DEL USUARIO. SOLICITE CUALQUIER OPERACION DE MANTENIMIENTO A PERSONAL DE SERVICIO CALIFICADO.

A VISO: Para reducir el riesgo de incendio o descarga eléctrica, no exponga esta unidad a la lluvia ni a la

humedad.

de Clase B, de acuerdo con la Parte 15 del Reglamento de la FCC. Estos límites están diseñados para proporcionar protección razonable contra interferencias perjudiciales en una instalación residencial. Este equipo genera o emplea energía de radiofrecuencia y, si no es instalado y empleado de acuerdo con estas instrucciones, puede causar interferencias perjudiciales a las radiocomunicaciones.

Sin embargo, no garantizamos que no ocurrirán interferencias en una instalación en particular. Si este equipo causa interferencias perjudiciales a la recepción radial o televisiva, situación que puede ser determinada apagando y encendiendo el equipo, se sugiere al usuario que trate de corregir tal interferencia mediante una o más de las siguientes medidas:

El símbolo del rayo dentro de un triángulo equilátero tiene por finalidad alertar al usuario acerca de la presencia de tensión peligrosa (sin aislación) en el interior del producto, que puede tener la intensidad suficiente como para constituir un riesgo de descarga eléctrica.

El signo de exclamación dentro de un triángulo equilátero tiene por finalidad alertar al usuario de importantes instrucciones de operación y mantenimiento (servicio) en la literatura que acompaña a este aparato.

ALL

- Reorientar o relocalizar la antena receptora.

- Incrementar la separación entre el equipo y el receptor.

- Conectar el equipo a un tomacorriente o circuito diferente al que está conectado al receptor.

- Consultar con el concesionario o un técnico experimentado solicitándole su asistencia.

PRECAUCION: El usuario corre el riesgo de perder la autorización para hacer funcionar este equipo en caso de que

ejecute un cambio o modificación no aprobado por la parte responsable para la conformidad con las Reglas FCC.

PRECAUCION:

ESTE TOCADISCOS DE VIDEO DIGITAL UTILIZA UN SISTEMA LASER. PARA UTILIZAR CORRECTAMENTE ESTE PRODUCTO, LEA CUIDADOSAMENTE ESTE MANUAL DE INSTRUCCIONES Y

GUARDELO P ARA SU REFERENCIA EN EL FUTURO. SI FUERA NECESARIO HACER UN MANTENIMIENTO DE ESTE APARATO, CONSULTE CON UN CENTRO DE SER VICIO AUTORIZADO-LEA EL PROCEDIMIENT O DE SERVICIO.

EL USO DE LOS CONTROLES, AJUSTES O LA REALIZACION DE OTROS PROCEDIMIENTOS QUE NO SEAN LOS ESPECIFICADOS AQUI PUEDE PROVOCAR UNA EXPOSICION A RADIACIONES PELIGROSAS.

PARA EVITAR LA EXPOSICION DIRECTA A LOS RAYOS LASER, NO TRATE DE ABRIR LA CAJA. PUEDE HABER UNA RADIACION LASER VISIBLE AL ABRIR LA CAJA. NO MIRE HACIA EL RAYO.

2C53307A (SP) Q Sheet 21/4/04, 11:161

Page 74

INSTRUCCIONES IMPORT ANTES

1. LEA LAS INSTRUCCIONES

Antes de usar la unidad, lea detenidamente todas las instrucciones de seguridad y operación.

2. CONSERVE ESTE MANUAL DE INSTRUCCIONES

Conserve las instrucciones de seguridad y operación para consultas futuras.

3. RESPETE LAS ADVERTENCIAS

Observe estrictamente todas las advertencias impresas en la unidad y las incluidas en el manual de instrucciones.

4. SIGA LAS INSTRUCCIONES

Siga todas las instrucciones de operación y uso.

5. LIMPIEZA

Antes de limpiar este videograbador, desconéctelo del tomacorriente mural. No use limpiadores líquidos ni aerosol. Utilice sólo un paño húmedo para limpiar el exterior del mueble.

6. ENCHUFES

El fabricante de esta unidad no hace ninguna recomendación de accesorios ya que pueden ser peligrosos.

7. AGUA Y HUMEDAD

No utilice este aparato cerca del agua. Por ejemplo cerca de una bañera, lavabo, pileta de la cocina, lavadero, en un sótano húmedo o cerca de una piscina.

8. ACCESORIOS

No instale esta unidad en un carro, soporte, trípode o mesa inestables. La unidad podría caerse, causando serias lesiones, resultando también severamente dañada a la unidad.

8A. La combinación de aparato y carro deberá ser movida con cuidado. Las

detenciones bruscas, la fuerza excesiva y las superficies disparejas podrán hacer que el aparato y el carro se vuelven.

9. VENTILACION

Las ranuras y aberturas en la parte trasera o inferior del mueble son para ventilación permiten un funcionamiento fiable de la unidad, protegiendo contra calentamiento excesivo. Estas aberturas no deberán ser bloqueadas ni cubiertas. Para evitar bloquear las aberturas, nunca sitúe la unidad encima de una cama, sofá, alfombra u otra superficie similar. Tampoco instale la unidad cerca o encima de un radiador o calefactor. La unidad no deberá ser instalado en un mueble empotrado, como ser una repisa para libros o bastidor, a menos que se pueda garantizar una ventilación adecuada, y/o cuando las instrucciones del fabricante así lo especifiquen.

10. FUENTES DE ALIMENTACION

Esta unidad sólo deberá ser operada mediante el tipo de fuente de alimentación especificado en la etiqueta indicadora. Si no está seguro del tipo de fuente de alimentación que tiene en su casa, consulte a su distribuidor o a la compañía de electricidad local. En el caso de unidades diseñadas para funcionar a pilas o con otras fuentes de alimentación, consulte el manual de instrucciones respectivo.

11. CONEXIÓN A TIERRA O POLARIZACION

Esta unidad está equipada con una clavija polarizada de corriente alterna (una clavija que tiene una espiga más ancha que la otra). Esta clavija solamente puede ser insertada en el tomacorriente en una sola dirección. Esta es una medida de seguridad. Si no pudiera insertar completamente la clavija en el tomacorriente, vuelva a intentarlo invirtiendo la clavija. Si aún no fuera posible insertar la clavija, tome contacto con un electricista para que reemplace su tomacorriente obsoleto. En lugar de la clavija polarizada de corriente alterna, su unidad puede estar equipada con una clavija de conexión a tierra de 3 alambres (una clavija con una tercera espiga de conexión a tierra). Este tipo de clavija sólo puede ser insertado en un tomacorriente con contacto a tierra. Esto también es una medida de seguridad. Si no pudiera insertar la clavija en el tomacorriente, tome contacto con un electricista para que reemplace su tomacorriente obsoleto. No modifique las características de seguridad de la clavija de conexión a tierra.

12. PROTECCION DEL CABLE DE ALIMENTACION

Los cables de alimentación deberán ser tendidos de manera tal que la probabilidad de que sean pisados o aplastados por otros objetos sea mínima. Preste especial atención a las clavijas de los cables, a los receptáculos, y al punto por donde salen del aparato.

13. TORMENTAS ELECTRICAS

Como medida de protección durante tormentas eléctricas, o cuando el videograbador permanezca sin uso durante períodos prolongados de tiempo, desconéctelo del tomacorriente mural y desconecte la antena o el sistema de cable. Esto evitará que la unidad resulte dañada por tormentas eléctricas o sobretensiones en la línea de alimentación.

14. LINEAS DE ALIMENTACION

Un sistema de antena exterior no debería situarse cerca de líneas de alimentación aéreas ni de otros circuitos de luz eléctrica o potencia, o donde pueda caerse o entrar en contacto con tales líneas o circuitos de alimentación. Al instalar un sistema de antena exterior, tenga mucho cuidado de no tocar tales líneas o circuitos de alimentación, ya que el contacto con ellos podría ser fatal.

15. SOBRECARGA

No sobrecargue los tomacorrientes murales ni los cables de extensión, ya que esto podría causar incendios o descargas eléctricas.

16. ENTRADA DE OBJETOS Y LIQUIDOS

Nunca introduzca objetos de ningún tipo por las aberturas de la unidad, ya que podría tocar peligrosos puntos de alta tensión o piezas de cortocircuito, provocando incendios o descargas eléctricas. Nunca derrame ni rocíe ningún tipo de líquido sobre la unidad.

17. CONEXION A TIERRA DE LA ANTENA EXTERIOR

Si se conecta una antena externa o sistema de cable a la unidad, cerciórese de que el sistema de antena o cable está conectado a tierra para darle protección contra sobretensión y acumulación de carga estática. La Sección 810 del Código Nacional de Electricidad, ANSI/NFP A 70, entrega información acerca de la manera correcta de conectar a tierra el mástil y la estructura soportante, puesta a tierra del alambre de entrada a una unidad de descarga de antena, tamaño de los conductores de puesta a tierra, ubicación de la nidad de descarga de la antena, conexión a los electrodos de tierra, y requisitos para el electrodo de tierra.

18. SERVICIO

No intente reparar la unidad usted mismo; al abrir o retirar las cubiertas usted se expondrá a alta tensión y a otros peligros. Solicite todo servicio a personal calificado. Ejemplo: a. Cuando el cable de alimentación o la clavija estén dañados. b. Si se ha derramado líquido sobre la unidad, o si algún objeto ha caído dentro

del videograbador. c. Si la unidad ha sido expuesta a la lluvia o al agua. d. Cuando a pesar de haber seguido las instrucciones de operación, la unidad

no funcione normalmente.

Ajuste solamente los controles indicados en el manual de instrucciones;el

ajuste incorrecto de otros controles podrá causar daños a la unidad, la que

por lo general requerirá de un prolongado trabajo de reparación (por un

técnico calificado) para que sus condiciones normales de operación puedan

ser restablecidas. e. Si la unidad se ha caída o si el gabinete se ha dañado. f . Cuando la unidad muestre un cambio notorio en su rendimiento.

19. PIEZAS DE REPUESTO

Cuando sea necesario reemplazar piezas, asegúrese de que el técnico de servicio emplee las piezas de repuesto especificadas por el fabricante, o piezas que tengan las mismas características que las piezas originales. Los cambios no autorizados podrán causar incendios, descargas eléctricas y otros problemas.

20. REVISION DE SEGURIDAD

Al finalizar cualquier servicio de mantenimiento o reparación de esta unidad, solicítele al técnico que efectúe comprobaciones de seguridad para determinar si el videograbador se encuentra o no en condiciones óptimas de operación.

21. CALOR

El producto debe ser situado lejos de fuente de calor como radiadores, reguladores de calefacción, estufas o otros productos (incluyendo amplificadores) que se producen calor.

22. BANDEJA DEL DISCO

No acerque sus dedos a la bandeja del disco cuando se está cerrando. Puede recibir heridas graves.

23. CONEXION

Cuando conecte el producto a otro equipo, desconecte la alimentación y desenchufe todos los equipos del tomacorriente. Si no lo hace, puede provocar una descarga eléctrica y heridas graves. Lea cuidadosamente el manual de instrucciones del otro equipo y respete las instrucciones al hacer las conexiones.

24. RAYO LASER

No mire por la ranura de la bandeja del disco por las salidas de circulación de aire del producto para ver la fuente del rayo láser. Puede dañar sus ojos.

25. DISCO

No utilice un disco rayado, deformado o reparado. Estos discos se pueden romper fácilmente y provocar serias heridas o averías en el producto.

26. NOTA PARA LA PERSONA QUE INSTALE EL SISTEMA CATV

Se ha incluido este recordatorio para llamar la atención de quien instale el sistema CATV, con respecto al Artículo 820-40 de la NEC, que entrega directivas de guía para realizar una conexión adecuada a tierra y, en particular, especifica que el cable de puesta a tierra debe ser conectado al sistema de conexión a tierra del edificio, lo más cerca del punto de entrada del cable como sea posible.

CONDENSACION

Se condensará humedad en la sección de funcionamiento del DVD/VCR si se lo trae de un lugar fresco a una habitación caliente o si la temperatura en la habitación sube repentinamente. En este caso, se verán afectadas las prestaciones del DVD/VCR. Para evitarlo, deje el DVD/VCR a la nueva temperatura durante aproximadamente una hora antes de conectarlo, o haga que la temperatura en la habitación suba gradualmente. También puede condensarse humedad durante el verano si el DVD/VCR está expuesta a una corriente de aire del acondicionador de aire. En estos casos, cambie el lugar donde está instalado el DVD/VCR.

2C53307A (SP) Q Sheet 21/4/04, 11:162

Page 75

Conexión a un televisor

VCR MENU

SETUP

VCR MENU

SETUP

Antennas separadas VHF y UHF

Flujo de la señal

a un tomacorriente de la red (120 V CA, 60 Hz)

A ENTRADA DE ANTANA

(roja) (blanca)

(amarilla)

A SALIDA DE

VIDEO

A ENTRADA DE VIDEO

Cordón AUDIO/ VIDEO (incluido)

AENTRADA DE AUDIO

(blanca)

(roja)

(amarilla)

A SALIDA DE ANTANA

A ENTRADA DE ANTANA

Televisor o monitor con entrada de audio/video

Ajuste del canal de video

Mantenga presionado 3 o 4 durante 3 segundos en el mode desconectado para seleccionar CH 3 o 4.

3 4

Presione POWER para encender el DVD/VCR.

El número del canal seleccionado parpadeará en la pantalla durante 3 segundos.

Presione VCR DVD para seleccionar el modo VCR.

VCR

3 4

5 6

DVD

Encienda el televisor y ajústelo al canal 3 o 4, en correspondencia con el canal seleccionado en el paso 1.

Presione TV/VCR para seleccionar la posición VCR.

TV/VCR

Presione el botón selector de canal en + o – (CH + / –) para recibir una estación de TV de su área. El número de canal aparecerá en la pantalla durante unos 4 segundos.

El indicador VCR del panel frontal se iluminará.

El indicador VCR se iluminará.

Seleccion de idioma en pantalla

Presione VCR MENU. Presione SET + o – para seleccionar

la opción “SYSTEM SETUP”, luego presione ENTER.

Si utiliza la unidad por primera vez y presiona VCR MENU, es posible que aparezca la pantalla de menú SYSTEM SETUP en lugar de la pantalla del menú principal.

Presione SET + o – para seleccionar el modo LANGUAGE, luego presione ENTER.

SET

–

Presione SET + o – para seleccionar el idioma deseada: inglés (ENGLISH), español (ESPAÑOL) o francés (FRANCAIS), luego presione ENTER.

Presione VCR MENU para volver a la imagen normal de TV.

ENTER

–

SET

–

ENTER

–

SET

2C53307A (SP) Q Sheet 21/4/04, 11:163

Page 76

Ajuste de reloj automatico

Seleccion de TV/CATV

Connecte la antena o sistema de cable.

• Si utiliza una caja de cable,

enciéndala.

Enchufe el cable eléctrico de CA a un tomacorriente CA.

Compruebe que el DVD/VCR está apagado.

Si presiona POWER, el ajuste

•

automático no se activará

Espere por lo menos tres minutos y presione POWER.

Presione CALL para verificar el reloj en la pantalla.

CALL

DISPLAY

Si el reloj no ha quedado ajustado, verifique el estado de la antena. El reloj automático no funciona en el estado de recepción.

Ajuste de reroj manual

Presione VCR MENU.

VCR MENU

SETUP

SET

–

ENTER

–

SET

Presione SET + o – para

seleccionar la opción “CH SETUP”, luego presione ENTER.

Presione SET + o – para seleccionar el modo “TV/CA TV”.

SET

–

ENTER

–

SET

Presione ENTER para seleccionar el modo TV o CATV. La flecha indica el modo seleccionado.

SET

–

ENTER

–

SET

TV - Canales de VHF/UHF CATV - Canales de TV CABLE

Presione VCR MENU para volver a la imagen normal de TV.

VCR MENU

SETUP

Ajuste automático de los canales

Repita el paso 1 descrito arriba y presione SET + o – para seleccionar la opción “AUTO CH MEMORY”.

SET

–

ENTER

–

SET

Presione VCR MENU.

VCR MENU

SETUP

Presione SET + o – para seleccionar la optión “SYSTEM SETUP”, luego presione ENTER.

SET

–

ENTER

–

SET

Presione SET + o – para seleccionar la opción “CLOCK SET”, luego presione ENTER.

SET

–

ENTER

–

SET

Presione el botón SET + o – para establecer el mes, y a continuación presione el botón ENTER.

SET

–

ENTER

–

SET

Ajuste el día, año y hora de acuerdo con el procedimiento del paso 4.

Una vez ajustado el reloj, la fecha y la hora empiezan a funcionar automáticamente.

Luego presione ENTER.

SET

–

ENTER

–

SET

Empieza la sintonización automática. La indicación de canal irá subiendo y cuando termina, la pantalla vuelve a su estado normal.

Borrado de un canal de la memoria

Repita el paso 1 descrito arriba seleccionar la opción “ADD/DELETE”, luego presione ENTER.

SET

–

ENTER

–

SET

Para añadir o borrar los canales deseados

Presione los botones de número o SET + o –

para seleccionar un número de canal que desee añadir o borrar.

Para añadir canales

Presione ENTER hasta que aparezca “ADD” en

321

la pantalla para añadir el canal sin memorizar.

654

Para borrar canales

7 9

Presione ENTER hasta que aparezca “DELETE”

SET

–

en la pantalla para borrar el canal de la memoria.

ENTER

El número del canal parpadeará.

–

SET

Repita de a para añadir o borrar otro canal.

y presione SET + o – para

2C53307A (SP) Q Sheet 21/4/04, 11:164

Page 77

Reproducción

7 9

654

321

Camara lenta

Coloque una cinta pregrabada. (Cuando se carga una cinta de cassette sin la lengüeta de prevención de borrado, la reproducción

comenzará automáticamente.)

PARA INICIAR LA REPRODUCCION

PLAY

PARA INTERRUMPIR REPRODUCCION

Presione PLAY. La reproducción comenzará. “ ” aparecerá en pantalla durante 4 segundos aproximadamente.

Presione STOP (PARADA) una vez. La cinta parará, pero permanecerá cargada y lista para reproducir. “ ” aparecerá en pantalla durante 4 segundos aproximadamente.

Rebobinado o avance rápido de la cinta

Detenga la reproducción o la grabación mediante STOP. Para rebobinar la cinta:

REW

Para avanzar la cinta:

FWD

Para detener el bobinado de la cinta, presione STOP. Para pasar directamente a reproducción (sin presionar STOP), presione

PLAY.

Modo de búsqueda de imagen hacia delante/atrás

Mientras se bobina la cinta, puede pasar al modo de búsqueda de imagen. Para ello, presione REW o FWD y manténgalo presionado. La unidad volverá a bobinar la cinta en cuanto se suelte el botón.

Presione REW.

Presione FWD.

Búsqueda de imagen

Función de búsqueda de imagen hacia atrás Presione REW una o dos veces durante la reproducción.

REW

Función de búsqueda de imagen hacia delante

Presione FWD una o dos veces durante la reproducción. Para volver a la reproducción: Presione PLAY.

FWD

Imagen fija

Presione PAUSE/STILL durante la reproducción. Para continuar la reproducción normal: Presione PLAY o PAUSE/ STILL.

Durante la reproducción presione SLOW. Para volver a la reproducción: Presione PLAY o SLOW.

SLOW

Avance cuadro a cuadro

Presione PAUSE/STILL durante la reproducción. Presione SLOW repetidamente: La imagen avanza cuadro a cuadro. Para volver a la reproducción: Presione PLAY o PAUSE/STILL.

SLOW

Grabacion de un programa de TV

Coloque un cassette en el cual la lengüeta de protección contra borrados accidentales esté intacta.

El DVD/VCR se encenderá automáticamente. Presione SP/SLP para seleccionar la velocidad de

cinta deseada SP o SLP.

SP/SLP

PLAY MODE

Ajuste la opción TV/CATV en la posición apropiada.

Presione los botones de selección directa de canal para seleccionar el canal o CH +/– a grabar:

SET

–

ENTER

–

SET

Presione el botón REC.

REC/OTR

Presione el botón de parada STOP para detener la grabacion.

El contador y “SP” o “SLP” se aparecerá en la pantalla durante 4 segundos aproximadamente.

TV - Canales de VHF/UHF CATV - Canales de TV CABLE

Selección directa de canal en modo de TV:

Todos los canales podrán ser seleccionados en forma instantánea usando sólo dos botones. (Por ejemplo, para seleccionar el canal 2, presione “0” y “2”. Si usted sólo presiona “2”, la selección del canal se retardará dos segundos.) Para los canales de 10 en adelante, presione los dos digitos en orden.

Selección directa de canal en modo de CATV:

1-9 Presione 0 dos veces y luego 1 al 9

como se requiera. Ej.:para seleccionar 2, presione “002”.

10-12 Presione primero el 0 y luego los 2

dígitos restantes en el orden de izquierda a derecha. Ej.: presione 012 para “12”.

13-99 Presione 2 dígitos en orden.

Ej.: presione 22 para “22”.

100-125

Presione 3 dígitos en orden. Ej.: Presione 110 para “110”.

“ ” aparecerá en la pantalla durante 4 segundos aproximadamente. El indicador “ REC ” aparecerá en pantalla.

” aparecerá en pantalla durante 4

“ segundos aproximadamente.

2C53307A (SP) Q Sheet 21/4/04, 11:165

Page 78

Grabacion por temporizador

Grebacion por temporizador de un solo toque (OTR)

Presione VCR MENU. Seleccione la opción TIMER REC SET y presione ENTER.

VCR MENU

SETUP

SET

–

ENTER

–

SET

Presione SET + o – para seleccionar el N° de programa, luego presione ENTER.

SET

–

ENTER

–

SET

Presione SET + o – para seleccionar la fecha deseada, luego presione ENTER.

SET

–

ENTER

–

SET

Ajuste el tiempo de partida, tiempo de término, canal y velocidad de cinta como en paso 3.

Para fijar otros programas, repita los pasos 2 al 4 para fija el otro programas.

VCR MENU

SETUP

• Para volver a la pantalla normal, presione dos veces VCR MENU.

Presione TIMER REC. El símbolo de reloj ( ) aparecerá en el visualizador y el VCR quedará en

modo de espera para grabación.

TIMER REC

Al mismo tiempo, el modo VCR cambiará automáticamente a modo DVD. Es posible utilizar el DVD incluso cuando el VCR está en modo de grabación por temporizador. Si no utiliza el DVD, apáguelo.

Coloque un cassette con la lengüeta de protección contra borrados accidentales esté intacta.

El DVD/VCR se encenderá automáticamente.

Presione SP/SLP para seleccionar la velocidad de la cinta deseada SP o SLP.

SP/SLP

PLAY MODE

El contador y “SP” o “SLP” aparecerán en pantalla durante 4 segundos aproximadamente.

Ajuste la opción TV/CATV en la posición apropiada.

TV - Canales de VHF/UHF CATV - Canales de TV CABLE

Presione el botones de selección de canales directos o botón CH +/– para seleccionar el canal a ser grabado.

7 9

321

654

SET

–

ENTER

–

SET

Presione OTR para comenzar la grabación. Presione el botón nuevamente para detener la grabación después

de 30 minutos. Cada presión de OTR aumentará el tiempo de grabación hasta un máximo de 6 horas. OTR y el tiempo de grabación aparecerá en pantalla durante 4 segundos. Y

REC/OTR

“ ” aparecerá en el visualizador.

Presione Una vez 2 veces 3 veces 4 veces 5 veces

Tiempo de Grabac.

GRABAC. NORMAL

0:30 1:00 1:30 2:00

Presione 6 veces 7 veces 8 veces 9 veces 10 veces

Tiempo de Grabac.

3:00 4:00 5:00 6:00

GRABAC. NORMAL

Para cancelar OTR

Presione STOP (PARADA) para apagar la energía. “ ” aparecerá en pantalla durante 4 segundos aproximadamente.

Si desea ver la reproducción del DVD durante el OTR o grabación estándar, presione VCR DVD para cambiar al modo DVD y reproducir el DVD.

2C53307A (SP) Q Sheet 21/4/04, 11:176

Page 79

Reproducción básica (DVD) Reproducción con avance rápido

Preparación:

•

ENCIENDA el TV y ajústelo en el modo de entrada de video.

•

Presione VCR DVD para seleccionar el modo DVD. (El indicador DVD se iluminará.)

Presione OPEN/CLOSE en el aparato. Se abrirá la bandeja del disco.

Coloque un disco en la bandeja. Sujete el disco, colóquelo con el lado de etiqueta impresa hacia arriba, alinee en las

guía y coloque el disco en su posición correcta.

Presione PLAY o OPEN/CLOSE en el aparato. La bandeja del disco se cierra automáticamente.

En la pantalla del TV la indicación “ y empieza la reproducción.

• Aparece la pantalla del menú en la pantalla de TV, si el disco tiene una función de menú. En este caso, presione activar una función de menú.

PLAY

Presione STOP para terminar la reproducción.

• El aparato graba el punto de parada, según el disco.

Aparece “ continuar reproduciendo (desde el mismo punto).

• Si presiona nuevamente STOP o se retira el disco (Aparece “ de parada.

PLAY

Para la reproducción, presione STOP. A continuación presione OPEN/CLOSE en el aparato.

Se abre la bandeja del disco. Saque el disco y presione OPEN/CLOSE en el aparato y

presione POWER ( automáticamente y se desconecta el aparato.

” en la pantalla. Presione PLAY para

” en la pantalla), el aparato borrará el punto

). La bandeja del disco se cierra

” cambia a “Reading”

, , , ó ENTER para

SET

–

ENTER

–

SET

Presione FWD durante la reproducción normal. Cada vez que presione el botón de FWD, aumentará la velocidad de la búsqueda.

Para seguir con la reproducción normal, presione PLAY.

•

FWD

PLAY

Reproducción con retroceso rápido

Presione REW durante la reproducción normal. Cada vez que presione el botón de REW, aumentará la velocidad de la búsqueda.

Para seguir con la reproducción normal, presione PLAY.

•

REW

PLAY

Reproducción Fija

Presione PAUSE/STILL durante la reproducción normal para hacer una pausa en la reproducción.

• Para seguir con la reproducción normal, presione PLAY.

PLAY

Avance cuadro por cuadro

Presione PAUSE/STILL durante la imagen fija. Avanza un cuadro cuando presione PAUSE/STILL una vez.

• Para seguir con la reproducción normal, presione PLAY.

PLAY

Reproducción de cámara lenta

2C53307A (SP) Q Sheet 21/4/04, 11:177

Presione SLOW( ) durante la reproducción normal o cuadro a cuadro. Cada vez que presione el botón de SLOW, cambiará la velocidad del slow.

• Para seguir con la reproducción normal, presione PLAY.

• Para volver a la imagen fija, presione PAUSE/STILL.

SLOW

PLAY

Page 80

Búsqueda de un capítulo o canción

Coloque las pilas

Pulse SKIP o varias veces para visualizar el capítulo o la pista que desee.

La reproducción se inicia desde el capítulo o la pista que haya seleccionado.

INDEX

SKIP

INDEX

–

SKIP

Para localizar capítulos o pistas subsiguientes.

La reproducción se inicia desde el principio del capítulo o pista actual. Si se pulsa dos veces, la reproducción se inicia desde el principio del capítulo o pista anterior.

Funciones básicas del control remoto

• Presione POWER ( ) para encender o apagar el DVD/

VCR.

• Seleccione su modo operativo deseado (DVD o VCR) utilizando VCR DVD. El indicador DVD o VCR del panel frontal le mostrará qué modo está seleccionado.

• Presione CH + o CH – para desplazarse por los canales uno a la vez.

• CH +/– ( para navegar por el sistema de menús en pantalla.

• Los botones de número permiten acceder directamente a canales concretos.

• Cada vez que se presiona VCR DVD en el control remoto, la pantalla alterna entre la pantalla VCR (modo VCR) y la pantalla DVD (modo DVD).

Funcionamiento

• Apunte el mando a distancia al sensor remoto y presione los botones de control para hacer funcionar.

• Utilice el control remoto dentro de un ángulo de 30˚ hacia ambos lados del sensor remoto, hasta una distancia de unos 7 metros.

/ ) y SET +/– ( / ) se utilizan también

Deslice la tapa del compartimento de las pilas

siguiendo la dirección de la flecha.

Coloque dos pilas “AAA”, (suministradas) prestando

atención a las marcas de polaridad en el compartimiento de las pilas.

Recoloque la tapa del compartimiento.

Notas sobre los derechos de autor

La ley prohibe copiar, difundir, mostrar, emitir por cable, reproducir en público, y alquilar sin permiso material con derechos de autor reservados (copyright).

Este dispositivo no graba en cinta DVDs protegidos contra copias. El dispositivo no ha de utilizarse para copiar contenidos bajo Copyright sin el permiso expreso por escrito del propietario de los derechos de autor. La obtención de tal permiso es responsabilidad exclusiva del usuario.

Este producto incorpora la tecnología de protección de derechos de autor (Copyright) mediante un método que protege ciertas patentes de EE.UU. y otros derechos de propiedad intelectual pertenecientes a Macrovision Corporation y otros propietarios de derechos. La utilización de esta tecnología de protección deberá ser autorizada por Macrovision Corporation, y tiene como fin la utilización en el hogar y otros usos de contemplación limitados a menos que Macrovision Corporation autorice otra cosa. Está prohibido modificar esta ingeniería y desmontar la unidad.

Fabricado bajo licencia de Dolby Laboratories. “Dolby”, “Pro Logic” y el símbolo de la doble D son marcas comerciales de Dolby Laboratories.

J2C53307A U

2C53307A (SP) Q Sheet 21/4/04, 11:178