Toshiba SD-5970 User Manual

Introduction

2

DIGITAL VIDEO

DVD VIDEO PLAYER

SD-5970SU

SD-5970SC

OWNER’S MANUAL

Connections

Basic playback

Advanced playback

Function setup

Others

18

26

34

51

60

© 2004 Toshiba Corporation

Introduction

SAFETY PRECAUTIONS

The lightning flash with arrowhead symbol, within an equi­lateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s en­closure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle is in­tended to alert the user to the presence of important operat­ing and maintenance (servicing) instructions in the litera­ture accompanying the appliance.

The symbol for CLASS II (Double Insulation)

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT
INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO
QUALIFIED PERSONNEL ONLY.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA

FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

CAUTION: This Digital Video Disc Player employs a Laser System.

To ensure proper use of this product, please read this owner’s manual carefully and retain for
future reference. Should the unit require maintenance, contact an authorized service location ­see service procedure.

Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.

FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications made to this equipment, not expressly approved by Toshiba, or
parties authorized by Toshiba, could void the user’s authority to operate the equipment.

2

The instructions shall state that an ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in
each pole shall be incorporated in the electrical installation of the building.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk

of electric shock do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.

In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD video
player.

Model No. Serial No.

Retain this information for future reference.

Location of the required label

Introduction

Be aware that this equipment is still powered even after the ON/STANDBY indicator turns off (standby mode) by
pressing the ON/STANDBY button. To disconnect this equipment completely from the mains power, pull out the
power plug from the wall outlet.

3

Introduction

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS

OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.

This set has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following
procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that
can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

4

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.

Introduction

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.

S3125A

5

Introduction

IMPORTANT SAFETY INSTRUCTIONS

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.

ADDITIONAL SAFETY INSTRUCTIONS

15.When you use headphones, keep the volume at a moderate level. If you use the headphones continuously
with high volume sound, it may cause hearing damage.

16.Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a
risk of fire or electric shock.

17.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.

6

18.Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious
personal injury.

19.Do not place a heavy object on or step on the apparatus. The object may fall, causing serious personal
injury and serious damage to the apparatus.

20.Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and apparatus malfunction.

21.If the apparatus should smoke or smell, immediately disconnect the power cord from the wall outlet. Wait
until the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause
fire.

Introduction

22.While it is thundering, do not touch the connecting cables or the apparatus.

23.The apparatus includes lead, an ingredient of solder used on the PCB, which is a harmful substance to
human and the environment. When disposing of this apparatus, follow the rules and regulations in your
area.

7

Introduction

Precautions

Notes on handling

When shipping the DVD video player, the original
shipping carton and packing materials come in handy.
For maximum protection, repack the unit as it was
originally packed at the factory. Take care not to give
it a shock or shake when carrying.
Do not use volatile liquids, such as insect spray, near
the DVD video player. Do not leave rubber or plastic
products in contact with the DVD video player for a
long time. They will leave marks on the finish.
The top and rear panels of the DVD video player may
become warm after a long period of use. This is not a
malfunction.
When the DVD video player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD video player for a long
period, the unit may not function properly in the
future. Turn on and use the DVD video player
occasionally.

Notes on locating

Place the DVD video player on a level surface. Do not
use it on a shaky or unstable surface such as a
wobbling table or inclined stand. The loaded disc may
come off the proper position and cause damage to
the DVD video player.
When you place this DVD video player near a TV,
radio, or VCR, the playback picture may become poor
and the sound may be distorted. In this case, place
the DVD video player away from the TV, radio, or
VCR.

Notes on moisture condensation

Moisture condensation damages the DVD video
player. Please read the following carefully.

Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts of
the DVD video player.

Moisture condensation occurs during the
following cases.

When you bring the DVD video player directly from a
cold place to a warm place.
When you use the DVD video player in a room where
you just turned on the heater, or a place where the
cold wind from the air conditioner directly hits the
unit.
In summer, when you use the DVD video player in a
hot and humid place just after you move the unit from
an air conditioned room.
When you use the DVD video player in a humid place.

Notes on cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the DVD
video player.
If you use a chemical saturated cloth to clean the
unit, follow that product’s instructions.

To obtain a clear picture

The DVD video player is a high technology, precision
device. If the optical pick-up lens and disc drive parts
are dirty or worn down, the picture quality becomes
poor. To obtain a clear picture, we recommend regular
inspection and maintenance (cleaning or parts
replacement) every 1,000 hours of use depending on
the operating environment. For details, contact your
nearest dealer.

8

Do not use the DVD video player when moisture
condensation may occur.

If you use the DVD video player in such a situation, it
may damage discs and internal parts. Remove the
disc, connect the power cord of the DVD video player
to the wall outlet, turn on the DVD video player, and
leave it for two or three hours. After two or three
hours, the DVD video player will have warmed up and
evaporated any moisture. Keep the DVD video player
connected to the wall outlet and moisture
condensation will seldom occur.

Notes on Discs

On handling discs

Do not touch the playback side of the disc.

Playback side

Do not attach paper or tape to discs.

On cleaning discs

Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.

Structure of disc contents

Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. VIDEO CDs and
audio CDs are divided into tracks.

DVD video disc

DVD video disc

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3

VIDEO CD/audio CD

VIDEO CD/audio CD

Track 1 Track 2 Track 3 Track 4 Tra ck 5

Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.

Introduction

If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.

Notes on copyright

It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, and rent copyrighted
material without permission.

DVD video discs are copy protected, and any
recordings made from these discs will be distorted.

This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.

9

Introduction

Notes on Discs (continued)

About this owner’s manual

This owner’s manual explains the basic instructions of
this DVD video player. Some DVD video discs are
produced in a manner that allows specific or limited
operation during playback. As such, the DVD video
player may not respond to all operating commands. This
is not a defect in the DVD video player. Refer to
instruction notes of discs.

” may appear on the TV screen during operation.

“

” means that the operation is not permitted by the

A “
DVD video player or the disc.

Notes on region numbers

The region number of this DVD video player is 1. If
region numbers, which stand for their playable area, are

printed on your DVD video disc and you do not find
or , disc playback will not be allowed by the player.

(In this case, the DVD video player will display a
message on-screen.) Some DVD discs may not have a
region code label even though their playback is
prohibited by area limits.

On VIDEO CDs

This DVD video player supports VIDEO CDs equipped
with the PBC (Version 2.0) function. (PBC is the
abbreviation of Playback Control.) You can enjoy two
playback variations depending on types of discs.

• VIDEO CD not equipped with PBC function
(Version 1.1)

Sound and movie can be played on this DVD video
player in the same way as an audio CD.

• VIDEO CD equipped with PBC function
(Version 2.0)

In addition to operation of a VIDEO CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.

Playable discs

This DVD video player can play the following discs.

Disc Mark

DVD
video
discs

VIDEO
CDs

Audio
CDs

The following discs are also available.

Some of these discs may be incompatible.

DIGITAL VIDEO

DVD-R discs of DVD video format
CD-R/CD-RW discs of CD-DA format

Contents

Audio

video

(moving

pictures)

Audio

video

(moving

pictures)

Audio

Disc
Size

12 cm

+

8 cm

12 cm

+

8 cm

12 cm

8 cm

(CD

single)

• You cannot play discs other than those listed above.

• You cannot play DVD-RAM discs or
non-standardized discs, etc., even if they may be
labeled as above.

• This DVD video player uses the NTSC color system,
and is not suitable to play DVD video discs recorded in
any other color system (PAL, SECAM, etc.).

Because of problems and errors that can occur during
the creation of DVD software and/or the manufacture of
DVD discs, Toshiba America Consumer Products, L.L.C.
and Toshiba of Canada, Ltd. cannot guarantee that this
player will play every feature of every DVD bearing the
DVD logo. As one of the creators of DVD technology,
Toshiba DVD players are manufactured to the highest
standards of quality and, as a result, such
incompatibilities are very rare. If you happen to
experience and difficulty playing a DVD on a Toshiba
DVD player, please feel free to call our Contact listed in
“How to Obtain Warranty Services”

Maximum

playback time

Approx. 4 hours

(single sided disc)

Approx. 8 hours

(double sided disc)

Approx. 80 minutes

(single sided disc)

Approx. 160 minutes

(double sided disc)

Approx. 74 minutes

Approx. 20 minutes

Approx. 74 minutes

Approx. 20 minutes

.

65

10

Table of Contents

Introduction

SAFETY PRECAUTIONS .......................... 2

IMPORTANT SAFETY INSTRUCTIONS ... 4

Precautions .............................................. 8

Notes on Discs ......................................... 9

Notes on region numbers ............................... 10

Table of Contents ................................... 11

Identification of Controls....................... 12

Front panel ..................................................... 12

Rear panel ...................................................... 12

DVD display .................................................... 13

Remote control ............................................... 14

Loading batteries ........................................... 15

Operating with the remote control .................. 15

Connections

Connecting to a TV ................................. 18

Connecting to a TV......................................... 18

Connecting to an audio system and TV

equipped with component video inputs ....... 19

Connecting to a display using HDMI .............. 20

Connecting to Optional Equipment ...... 21

Connecting to an amplifier equipped with a

Dolby Digital decoder ................................... 22

Connecting to an amplifier equipped with

Dolby Surround Pro Logic ............................ 22

Connecting to an amplifier equipped with a

DTS decoder ................................................ 23

Connecting to an amplifier equipped with an

MPEG2 audio decoder................................. 23

Connecting to an amplifier equipped with a

digital audio input ......................................... 24

Basic playback

Playing a Disc ......................................... 26

Basic playback ............................................... 26

Variable Speed Playback ....................... 28

Playing in fast reverse or fast forward

directions...................................................... 28

Playing frame by frame .................................. 28

Playing in slow-motion ................................... 29

Resuming playback from the same location .. 29

Locating a Desired Section ................... 30

Locating a title using the top menu ................ 30

Locating a desired section by entering the

corresponding number ................................. 31

Locating a specific chapter or track ............... 31

Advanced playback

Accessing a Specific Location Directly 34

Entering the time counter of the desired

location......................................................... 34

Playing in Random Order ...................... 35

Playing titles, chapaters or tracks in random

order ............................................................. 35

Playing Repeatedly ................................ 36

Repeating a title, chapter or tracks ................ 36

Repeating a specific segment ........................ 36

Playing in a Favorite Order .................... 37

Setting titles, chapters, or tracks in a favorite

order ............................................................. 37

Zooming a Picture .................................. 38

Zooming a picture .......................................... 38

Selecting the Camera Angle .................. 39

Changing the camera angle ........................... 39

Selecting Subtitles ................................. 40

Selecting a subtitle language .........................40

Selecting a Language ............................ 41

Selecting a playback audio setting................. 41

On-screen Display Operation ................ 42

On-screen display operation .......................... 42

Playing MP3/WMA Files ......................... 43

Playing MP3/WMA files .................................. 43

Viewing JPEG Files ................................ 45

Viewing JPEG files ......................................... 45

Viewing a thumbnail view ............................... 46

Function setup

Customizing the Function Settings ...... 50

Setting procedure ........................................... 50

Setting details ................................................. 52

Table of Languages ................................ 57

Others

Operating a TV with the

remote control ........................................ 60

Before Calling Service Personnel ......... 62

Specifications ......................................... 63

Limited United States Warranty ............ 64

How to Obtain Warranty Services .................. 65

CANADIAN WARRANTY

INFORMATION ........................................ 66

Introduction

11

Introduction

Identification of Controls

See the page in for details.

Front panel

Not lit.

Rear panel

24

ANALOG/HDMI
switch

SELECT button

20

20

24

12

HDMI OUT
jack

20

When connecting the optical digital cable, remove
the cap and fit the connector into the jack firmly.
When not using the jack, keep the cap inserted to
protect it from dust intrusion.

DVD display

Play mode

indicator

Title number

Total playing

time indicator

indicator

Pressing of the FL. DIM button on the remote
control changes the brightness of the display.

Chapter number

indicator

Memory playback indicator

Track number

indicator

Random playback indicator

Introduction

TITLETOTAL

CHPGROUP

TRK

R

M

MR

-

B

A

DVD

VCD

Multifunctional indicator (indicates

operating status or messages, etc.)

DVD / VIDEO CD /

CD indicator

When you start playback, the elapsed time indicators appear. Pressing the FL. SELECT button
switches them to the title/chapter/track number indicators. Some discs may not permit this
operation.

The indicators vary depending on the kinds of discs you play.

DVD video disc

• During playback:

Example

DVD

TITLE

• During playback:

Example

CHP

VCD

VIDEO CD Audio CD

TRK

Angle icon

indicator

Repeat playback

indicator

• During playback:

Example

CD

TRK

Playing chapter 3 of title 2

Some discs may not display chapter
numbers or elapsed time.

Playing track 6

Some discs may not display track
numbers or elapsed time.

Playing track 6

13

Introduction

Identification of Controls (continued)

The instructions in this manual describe the functions on the remote control. See the page in for details.

Remote control

TV button POWER button

DVD button

60

26

OPEN/CLOSE button

INPUT SELECT button

Number buttons

DISPLAY button

31

42

CLEAR button
SEARCH button

TOP MENU button

* MENU button

30

100 button
ZOOM button

60

REPEAT button

28

26

29

31

38

50

39

HDMI button
AUDIO button

FF button

28

SLOW button
STOP button

PAUSE/STEP button

FL.DIM button

ANGLE button

SUBTITLE button

PLAY button

REV button
SLOW button

SKIP buttons

SETUP button

A-B REPEAT button

CH/VOL/Direction
buttons

RETURN buttons

50

30

60

FL.SELECT

PROGRAM button
RANDOM button

PROGRESSIVE button

20

29

27

38

41

31

13

26

36

31

35

37

36

27

26

60

28

60

19

14

ENTER button

30

FL.SELECT button

* MENU button

Use the MENU button to display the menu included on
many DVD video discs. To operate a menu, follow the
instructions in “Locating a title using the top menu.”

30

13

Loading batteries

Operating with the remote control

Introduction

Open the cover.

1

Insert batteries (AAA size).

2

Make sure to match the + and on the batteries
to the marks inside the battery compartment.

Close the cover.

3

Point the remote control at the remote
sensor and press the buttons.

Distance: About 7 m (23 feet) from the front of the

remote sensor

Angle: About 30° in each direction of the front of

the remote sensor

* Do not expose the remote sensor of the DVD video

player to a strong light source such as direct
sunlight or other illumination. If you do so, you may
not be able to operate the DVD video player via the
remote control.

Notes on batteries

Improper use of batteries may cause battery leakage
and corrosion. To operate the remote control correctly,
follow the instructions below.

• Do not insert batteries into the remote control in the
wrong direction.

• Do not charge, heat, open, or short-circuit the batteries.
Do not throw batteries into a fire.

• Do not leave dead or exhausted batteries in the remote
control.

• Do not use different types of batteries together, or mix old
and new batteries.

• If you do not use the remote control for a long period of
time, remove the batteries to avoid possible damage from
battery corrosion.

• If the remote control does not function correctly or if the
operating range becomes reduced, replace all batteries
with new ones.

• If battery leakage occurs, wipe the battery liquid from the
battery compartment, then insert new batteries.

Notes on the remote control

• Direct the remote control at the remote sensor of the DVD
video player.

• When using the remote control, press the buttons at
intervals of about 1 second to ensure the correct mode of
operation.

• Do not drop or give the remote control a shock.

• Do not leave the remote control near an extremely hot or
humid place.

• Do not spill water or put anything wet on the remote
control.

• Do not open the remote control.

15

Connections

Read this chapter first to make all necessary
preparations.

Connecting to a TV

Connecting to an audio system
and TV equipped with
component video inputs

Connecting to a display using
HDMI

Connecting to an amplifier
equipped with a Dolby Digital
decoder

Connecting to an amplifier
equipped with Dolby Surround
Pro Logic

Connecting to an amplifier
equipped with a DTS decoder

Connecting to an amplifier
equipped with an MPEG2 audio
decoder

Connecting to an amplifier
equipped with a digital audio
input

Connections

Connecting to a TV

Connect the DVD video player to your TV.

For details of output sound, see 41.

Connecting to a TV

• Make the following setting.

ANALOG/HDMI SETTING

In standby mode, select ANALOG mode through the
ANALOG/HDMI switch on the front panel.

Notes

• Refer to the owner’s manual of the connected TV as well.

• When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the wall outlet
before making any connections.

• If your television set has one audio input, connect the left and right audio outputs of the DVD video player to a Y cable
adapter (not supplied) and then connect to your TV.

• Connect the DVD video player directly to your TV. If you connect the DVD video player to a VCR, TV/VCR combination or
video selector, the playback picture may be distorted as DVD video discs are copy protected.

• Analog audio out will not have sound if DTS playback is selected.

• Do not set the ANALOG/HDMI selection other than standby mode.

On-screen display Select:

“PCM” or “Raw”“Digital Out”

“Video Output”

* Only for analog video out jack (yellow) connection with

progressive scan off.

CVBS

* YUV

50

50

Page

55

54

18

Interlaced outputs (ColorStream®)

Some TVs or monitors are equipped with component video
inputs. Connecting to these inputs allows you to enjoy
higher quality picture playback.
Actual labels for component video inputs may vary
depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y,
CB, CR)
In some TVs or monitors, the color levels of the playback
picture may be reduced slightly or the tint may change. In
such a case, adjust the TV or monitor for optimum
performance.

Progressive outputs (ColorStream®Pro)

Some TVs or monitors are equipped with component video
inputs that are capable of reproducing a progressively
scanned video signal. Connecting to these inputs allows you
to view the highest quality pictures with less flicker.
Consumers should note that not all high definition television
sets are fully compatible with this product and may cause

artifacts to be displayed in the picture. In case of 525
progressive scan picture problems, it is recommended that the
user switch the connection to the “standard definition” output. If
there are questions regarding our TV set compatibility with this
model 525p DVD player, please contact our Customer Service
Center.

Connecting to a TV (Using the component video jacks)

Connections

ANALOG/HDMI
SETTING

In standby mode,
select ANALOG
mode through the
ANALOG/HDMI
switch on the front
panel.

Switching the output signal (interlaced/
progressive) using the remote control

You can temporarily switch the output signal for better picture
quality.

• Make the following setting.

On-screen display Select:

“PCM” or “Raw”“Digital Out”

50

Page

55

Press PROGRESSIVE on the remote control during stop mode.
Press PROGRESSIVE again to turn off progressive mode.

Notes

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.

• If you place the DVD video player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the
DVD video player away from the tuner and radio.

• The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, high volume sound may damage your hearing as well as the speakers.

• Turn off the amplifier before you connect or disconnect the DVD video player’s power cord. If you leave the amplifier power
on, the speakers may be damaged.

• Progressive can be on/off only when video output is set to YUV.

• In component connections (YUV), the screen might become pinkish in color when the video output is set to CVBS. This is
not a malfunction of this unit.

• When Progressive is on, only component video will be output.

• Analog audio out will not have sound if DTS playback is selected.

• When using component video cables, do not connect the S video cable.

54

54

“Video Output”

YUV

54

50

19

Connections

Connecting to a TV (Continued)

About HDMI

HDMI (High Definition Multimedia Interface) supports both
video and audio on a single digital connection for use with
DVD players, DTV, set-top boxes, and other AV devices.
HDMI was developed to provide the technologies of High
Bandwidth Digital Content Protection (HDCP) as well as
Digital Visual Interface (DVI) in one specification. HDCP is
used to protect digital content transmitted and received by
DVI-compliant or HDMI-compliant displays.

Connecting to a display (Using the HDMI cable)

HDMI has the capability to support standard, enhanced, or
high-definition video plus standard to multi-channel
surround-sound audio. HDMI features include
uncompressed digital video, a bandwidth of up to 2.2
gigabytes per second (with HDTV signals), one connector
(instead of several cables and connectors), and
communication between the AV source and AV devices
such as DTVs.

HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI licensing LLC.

To HDMI

OUT

HDMI Cable (supplied)

Switching the video quality (HDMI mode) using HDMI button
on the remote control or SELECT button on the Front Panel

In standby mode, select HDMI mode through the ANALOG/HDMI
switch on the front panel.
Press HDMI button on the remote control or SELECT button on the
front panel to receive suitable video quality. The video quality is
required to match your TV having HDMI feature and suitable quality,
please check your TV owner’s manual.
Pressing the HDMI button or SELECT button changes the video
quality as follows:

both TV and DVD display
within 2 seconds.

Notes

• Refer to the owner’s manual of the connected TV as well.

• When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the wall outlet
before making any connections.

• Select HDMI mode through the ANALOG/HDMI switch of front panel, analog video out jack (Yellow) will not have video signal.

• If you have a HDMI (with HDCP) equipped monitor or display, you can connect it to this player using the supplied HDMI cable.

• The HDMI connector outputs uncompressed digital video, as well as almost every kind of digital audio that the player is
compatible with, including DVD-Video, Video CD, CD and MP3.

• When using HDMI cable, do not connect to other analog video outputs.

• No sound will be output from the HDMI cable if the Digital Out is not set to PCM.

480p 720p 1080i 1024p

will show your selected video quality

13

• Make the following setting.

55

HDMI-compatible

On-screen display

“Digital Out”

display

Select:

“PCM”

50

Page

55

20

Connecting to Optional Equipment

You can enjoy high quality dynamic sounds by connecting the DVD video player
to optional audio equipment.

• For connection to your TV, see “Connecting to a TV”

18 19

• For details of output sound, see

20.
.

41

• This section uses the following reference marks.

: Front speaker

: Rear speaker

: Sub woofer

: Center speaker

: Signal flow

Notes

• DO NOT connect the OPTICAL or COAXIAL DIGITAL
AUDIO OUT jack of the DVD video player to the AC-3 RF
input of a Dolby Digital Receiver. This input on your A/V
Receiver is reserved for Laserdisc use only and is
incompatible with the OPTICAL / COAXIAL DIGITAL
AUDIO OUT jack of the DVD video player.

• Connect the COAXIAL DIGITAL AUDIO OUT jack of the
DVD video player to the “DIGITAL (COAXIAL)” input of a
Receiver or Processor.

• Connect the OPTICAL DIGITAL AUDIO OUT jack of the
DVD video player to the “DIGITAL (OPTICAL)” input of a
Receiver or Processor.

• Refer to the owner’s manual of the connected equipment
as well.

• When you connect the DVD video player to other
equipment, be sure to turn off the power and unplug all of
the equipment from the wall outlet before making any
connections.

• The output sound of the DVD video player has a wide
dynamic range. Be sure to adjust the receiver’s volume to
a moderate listening level. Otherwise, the speakers may
be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect
the DVD video player’s power cord. If you leave the
amplifier power on, the speakers may be damaged.

Warning

• When you are connecting (via the OPTICAL or
COAXIAL DIGITAL AUDIO OUT jack) an AV decoder
that does not have Dolby Digital, Digital Theater
Systems (DTS) or MPEG2 decoding function, be sure
to set “Digital Out” to “PCM” from the on-screen

displays 50 55. Otherwise, high volume sound may
damage your hearing as well as the speakers.

• When playing DTS-encoded discs (audio CDs),
excessive noise may be output from the analog audio
output jacks. To avoid possible damage to the audio
system, you should take proper precautions when the
analog audio output jacks of the DVD video player are
connected to an amplification system. To enjoy DTS
Digital Surround™ playback, an external 5.1 channel
DTS Digital Surround™ decoder system must be
connected to the OPTICAL or COAXIAL DIGITAL
AUDIO OUT jack of the DVD video player.

Connections

21

Connections

Connecting to Optional Equipment (Continued)

Connecting to an amplifier equipped with a Dolby Digital decoder

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the
latest movies, and is now available to reproduce this realistic effect in the home.
You can enjoy motion picture and live concert DVD video discs with this dynamic
realistic sound by connecting the DVD video player to a 6 channel amplifier
equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a
Dolby Surround Pro Logic decoder, you will obtain the full benefit of Pro Logic
from the same DVD movies that provide full 5.1-channel Dolby Digital
soundtracks, as well as from titles with the Dolby Surround mark.

Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and the
double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished
works. Copyright 1992-1997 Dolby
Laboratories. All rights reserved.

• Use DVD video discs encoded via
the Dolby Digital recording
system.

• Make the following setting.

Amplifier equipped with a
Dolby Digital decoder

To COAXIAL

type digital

audio input

To OPTICAL
type digital
audio input

Optical digital cable

75 Ω coaxial cable

Connect

either.

On-screen display Select:

“Raw”

“Digital Out”

Recording system

or

‘PCM”

Connecting to an amplifier equipped with Dolby Surround Pro Logic

Dolby Surround Pro Logic

You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by
connecting an amplifier and speaker system (right and left front speakers, a
center speaker, and one or two rear speakers).

With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an
amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s
owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro
Logic sound.

With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.

*

Amplifier equipped with
Dolby Surround Pro Logic

To audio input

To ANALOG
AUDIO OUT

• Make the following setting.

On-screen display Select:

“Digital Out”

* Connect one or two rear speakers.
The output sound from the rear speakers
will be monaural even if you connect two
rear speakers.

“Raw”

or

“PCM”

Page

50

55

41

D

Page

50

55

22

Audio cable

Connecting to an amplifier equipped with a DTS decoder

Connections

Digital Theater Systems (DTS)

DTS is a high quality surround technology used in theaters and now available for
home use, on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1
channel DTS encoded sound tracks on DVD video discs or audio CDs.

“DTS” and “DTS Digital Out” are
trademarks of Digital Theater Systems,
Inc.

• Use DVD video discs or audio
CDs encoded via the DTS
recording system.

• Make the following setting.

Amplifier equipped with
a DTS decoder

To COAXIAL

type digital
audio input

To OPTICAL
type digital
audio input

Optical digital cable

75 Ω coaxial cable

Connect

either.

On-screen display Select:

“Digital Out”

Recording system DTS

“Raw”

Connecting to an amplifier equipped with an MPEG2 audio decoder

MPEG2 sound

You can enjoy motion picture and live concert DVD video discs with
dynamic realistic sound by connecting an amplifier equipped with an
MPEG2 audio decoder or MPEG2 audio processor.

Amplifier equipped with an
MPEG2 audio decoder

To COAXIAL

type digital

audio input

To OPTICAL
type digital
audio input

Optical digital cable

Connect

either.

• Use DVD video discs encoded via
the MPEG2 recording system.

• Make the following setting.

On-screen display Select:

“Digital Out”

Recording system MPEG2

“Raw”

or

“PCM”

Page

50

55

41

Page

50

55

41

75 Ω coaxial cable

23

Connections

Connecting to Optional Equipment (Continued)

Connecting to an amplifier equipped with a digital audio input

2 channel digital stereo

You can enjoy the dynamic sound of 2 channel digital stereo by connecting an
amplifier equipped with a digital audio input and speaker system (right and left
front speakers).

Amplifier equipped with
a digital audio input

To COAXIAL

type digital

audio input

To OPTICAL
type digital
audio input

Optical digital cable

75 Ω coaxial cable

Connect

either.

• Make the following setting.

On-screen display Select:

“PCM”“Digital Out”

Page

50

55

24

Basic playback

Begin your operation.

Playing a Disc

Variable Speed Playback

Locating a Desired Section

Basic playback

CAUTION

Playing a Disc

This section shows you the basics on how to play a disc.

Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.

Basic playback

Preparations

• When you want to view a disc, turn on the TV and select the video input connected to the DVD video player.

• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected
to the DVD video player.

• Press DVD to select DVD mode.

Press the POWER button.

1

The DVD video player turns on.
The ON/STANDBY indicator on the
player illuminates.

Press OPEN/CLOSE.

2

The disc tray opens.

Place the disc on the disc tray.

3

With the playback
side down

• There are two different disc sizes. Place the disc in
the correct guide on the disc tray. If the disc is out of
the guide, it may damage the disc and cause the
DVD video player to malfunction.

• Do not place a disc which is unplayable in this DVD
video player.

Press OPEN/CLOSE to close the disc

4

tray.

Playback starts.

If you insert a DVD video disc that contains a
top menu, a menu may appear. Use the

/ to select the title you want to view, then

press ENTER to start playback. See “Locating a
title using the top menu”

• You may need to press the TOP MENU or MENU
button to display disc menu (depending on the
actual DVD video disc.)

Notes

• If the disc tray is holding a disc you have already played,
playback will begin from the location where you last
stopped. For resuming playback, see

• Some Video CD are recorded with PBC (Playback
Control), a menu with recorded contents may appear on
the TV if you have turned the PBC on. You can make your
selection according to its PBC menu. Press the MENU
button on the remote control to turn PBC on or off anytime
during Video CD playback. When switching from PBC off
to PBC on mode, playback will start from the beginning
of the disc.

To start playback in the stop mode

Press PLAY.

.

30

/ /

.

29

26

1
2,4

TOP MENU
MENU
PLAY
STOP

PAUSE/STOP
ENTER

To obtain a higher quality picture

Occasionally, some picture noise not usually visible during a normal broadcast
may appear on the TV screen while playing a DVD video disc because the high
resolution pictures on these discs include a lot of information. While the amount of
noise depends on the TV you use with this DVD video player, you should generally
reduce the sharpness adjustment on your TV when viewing DVD video discs.

About

The icons on the heading bar show the playable discs for the
function described under that heading.

DVD

: You can use this function with DVD video discs.
: You can use this function with VIDEO CDs.

CD

: You can use this function with audio CDs.

To pause playback (still mode)

Press PAUSE/STEP during playback.

To resume normal playback, press
the PLAY button.

• The sound is muted during still
mode.

To stop playback

Press STOP.

To remove the disc

Press OPEN/CLOSE.

Remove the disc after the disc tray
opens completely.

Be sure to press the OPEN/CLOSE button to close
the disc tray after you remove the disc.

To turn the power off (To enter the standby
mode)

Press STANDBY/ON button to turn the STANDBY/ON
indicator off.

Note

Be aware that this equipment is still powered even after the
ON/STANDBY indicator turns off (standby mode) by pressing
the ON/STANDBY button. To disconnect this equipment
completely from the mains power, pull out the power plug
from the wall outlet.

About the screen saver

If you pause a picture of a DVD video disc and leave it
still for a long while, the screen saver of the DVD video
player automatically appears. To turn off the screen
saver, press the PLAY button.

Automatic Power Off function

If the DVD video player is stopped, or the screen saver
is engaged for approximately 20 minutes, the DVD
video player will automatically turn itself off.

Basic playback

Notes

• Do not move the DVD video player during playback. Doing so may damage the disc.

• Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may
cause the DVD video player to malfunction.

• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD video
player to malfunction.

• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the
STOP button on your remote control once the movie is completed.

27

Basic playback

Variable Speed Playback

You can play discs at various speeds, and resume playback from the location
where you stopped playback.

Playing in fast reverse or fast forward directions

PLAY
REV

FF
STOP

SLOW
PAUSE

Press REV or FF during playback.

REV: Fast reverse playback
FF: Fast forward playback

Each time you press the REV or FF
button, the playback speed changes.

Playing frame by frame

Press PAUSE/STEP during still playback.

Each time you press the PAUSE/
STEP button, the picture advances
one frame.

To resume normal playback

Press PLAY.

Notes

• The DVD video player mutes sound and subtitles during
reverse and forward scan of DVD video discs. However, the
DVD video player plays sound during fast forward or fast
reverse play of audio CDs.

• The playback speed may differ depending on the disc.

To resume normal playback

Press PLAY.

Note

The sound is muted during frame by frame playback.

28

Playing in slow-motion

Press SLOW during playback.

Each time you press the SLOW
button, the slow-motion speed
changes in the following sequence:

4 8

4 8

To resume normal playback

Press PLAY.

Note

• The sound is muted during slow-motion playback.

• 3 speeds are available.

Resuming playback from the same location

Press STOP at the location where you
want to interrupt playback.

1

The DVD video player memorizes
the location where playback is
stopped.

Press PLAY.

To start playback from the beginning regardless
of the location where you stopped playback

1 Press STOP twice.

2 Press PLAY.

2

The DVD video player resumes
playback from the location where
you stopped playback.

• If you want to return to the beginning of a DVD video

The DVD video player deletes the
memory of the location.

DVD

Playback starts from the
beginning of the current title.

Playback starts from the
beginning of the disc.

disc, open and close the disc tray once with the
OPEN/CLOSE button before pressing the PLAY
button.

Basic playback

Notes

• Resuming cannot function when:
– you open the disc tray.
– you disconnect the power plug of the DVD video player.
– you play a PBC-featured video CD while the PBC is on.

• There may be a difference in the location where playback
resumes depending on the disc.

• Settings you changed using the on-screen displays while
the DVD video player keeps a location in the memory may
function only after the memory is cleared.

29

Basic playback

Locating a Desired Section

TOP MENU

ENTER

Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs are
divided into tracks. You can quickly locate any specific title, chapter, or track.

DVD video disc

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3

DVD

Locating a title using the top menu

Track 1

VIDEO CD/audio CD

Track 2 Track 3 Track 4 Track 5

Press TOP MENU.

1

The top menu appears on the TV
screen.

e.g.

Press / / / to select the title you
want.

2

If the titles in the top menu are
assigned a number, you can directly
locate a specific title by pressing its
designated number with the number
buttons.

Press ENTER.

3

Playback starts from chapter 1
of the selected title.

Notes

• The instructions above describe basic procedures which
may vary depending on the contents of the DVD video disc.
If different instructions appear on the TV screen, follow
those instructions.

• If you display the top menu during playback and press the
TOP MENU button again without selecting any title, the DVD
video player may resume playback from the point where you
first pressed the TOP MENU button (depending on the
actual DVD video disc.)

• This method of locating a title is available only on a disc that
contains a top menu.

• Instruction notes of discs may refer to the button that
displays the top menu as TITLE button.

30

Number buttons

CLEAR
SEARCH

SKIP

ENTER

Locating a desired section by entering the corresponding number

Press Search.

1

Press / to highlight the Title/Chapter
or Track.

If you are using a VIDEO CD/audio CD, skip step 2.
Then at step 3, enter the number for the track you
want using the number buttons.

e.g.

DVD

Track

Press / to select a section you want

2

to locate.

e.g. When you want to locate a chapter.

DVD

Press the number buttons to enter title,
chapter or track number.

3

Press ENTER.

4

Playback starts from the selected
section.

Notes

• Pressing the CLEAR button resets the numbers. To clear the
display, press the SEARCH button several times.

• This method of locating a title is available only on a disc that
contains title numbers.

Basic playback

Locating a specific chapter or track

Press SKIP or repeatedly to access
the chapter or track number you want.

Playback starts from the selected chapter or track.

To locate succeeding chapters or
tracks.

Playback starts from the
beginning of the current chapter
or track.
When you press twice in quick
successions, playback starts from
the beginning of the preceding
chapter or track.

Notes

• Some titles may not display chapter numbers.

• If you press and hold the SKIP or button on the
front panel during playback, the DVD video player performs
fast reverse or fast forward playback. You can vary the
speed by pressing the button repeatedly.
To locate chapters or tracks during fast reverse or fast
forward playback, first press the PLAY button to resume
normal playback, then use the SKIP or button.

31

Basic playback

32

Advanced playback

Customizing the performance of your DVD video player.

Accessing a Specific Location
Directly

Repeating Random Order

Playing Repeatedly

Playing in a Favorite Order

Zooming a Picture

Selecting the Camera Angle

Selecting Subtitles

Selecting a Language

On-screen Display Operation

Playing MP3/WMA Files

Viewing JPEG Files