<Concealed Duct Type>/<Type à conduits dissimulés>
<Lüftungskanalmontage in der Zwischendecke>/<Tipo a condotto nascosto>
<Modelo con conductos ocultos>/<Tipo conduta embutida>
<Type met weggewerkte kanalen>/<Фэрпт ухгкекблхммЭнпх бгщгпэ>
Heat Pump Model/Modèle à thermopompe
Geräte mit Heizung/Modello con pompa di riscaldamento
Modelo con bomba de calor/Modelo de bomba térmica
RAV-SM562BT-ERAV-SM562AT-ESP562AT- E
RAV-SM802BT-ERAV-SM802AT-ESP802AT- E
RAV-SM1102BT-ERAV-SM1102AT-ESP1102AT-E
RAV-SM1402BT-ERAV-SM1402AT-ESP1402AT-E
Thank you very much for purchasing TOSHIBA Air Conditioner.
Please read this owner's manual carefully before using your Air Conditioner.
• Be sure to obtain the “Owner’s manual” and “Installation manual” from constructor (or dealer).
Request to constructor or dealer
• Please clearly explain the contents of the Owner’s manual and hand over it.
Nous vous remercions pour avoir choisi un climatiseur TOSHIBA.
Veuillez lire attentivement ce Manuel du propriétaire avant d’utiliser votre climatiseur.
• Assurez-vous que le constructeur (ou le revendeur) vous remette le “Manuel du propriétaire” et le “Manuel d’installation”.
Demande au constructeur ou au revendeur
• Veuillez expliquer clairement le contenu du Manuel du propriétaire et le remettre au client.
Wir danken Ihnen, dass Sie sich für ein TOSHIBA Klimagerät entschieden haben.
Bitte lesen Sie diese Betriebsanleitung, bevor Sie Ihr Klimagerät benutzen, sorgfältig.
• Lassen Sie sich die “Betriebsanleitung” und das “Installations-Handbuch” unbedingt vom Installateur oder vom Lieferanten aushändigen.
Eine Bitte an den Installateur oder Lieferanten:
• Bitte erklären Sie dem Käufer den Inhalt der Betriebsanleitung und händigen sie ihm aus.
Grazie di aver acquistato un condizionatore d'aria TOSHIBA.
Prima di usare il condizionatore d'aria, leggere con attenzione questo manuale del proprietario.
• Si raccomanda di tenere a portata di mano il “Manuale del proprietario” e il “Manuale di installazione” ricevuti dal produttore (o dal
rivenditore).
Richiesta al produttore o al rivenditore
• Spiegare chiaramente il contenuto del Manuale del proprietario e consegnarne una copia all'utente.
Muchas gracias por haber adquirido el aparato de aire acondicionado TOSHIBA.
Lea atentamente este manual del propietario antes de utilizar el aparato de aire acondicionado.
• Asegúrese de que el fabricante (o distribuidor) le proporcione el “Manual del propietario” y el “Manual de instalación”.
Solicitud al fabricante o distribuidor
• Explique con claridad el contenido del Manual del propietario y entréguelo al cliente.
Muito obrigada por adquirir o Ar Condicionado TOSHIBA.
Leia atentamente este manual do utilizador antes de utilizar o seu ar condicionado.
• Não se esqueça de receber o “Manual do utilizador” e o “Manual de inslatação” do fabricante (ou agente).
Pedido ao fabricante ou agente
• Explique por favor o conteúdo do Manual do utilizador e entregue-o.
Hartelijk dank voor uw keuze voor een airconditioner van TOSHIBA.
Lees deze gebruiksaanwijzing zorgvuldig door voordat u de airconditioner gaat gebruiken.
• Zorg ervoor dat u zowel de ‘gebruiksaanwijzing’ als de ‘installatiehandleiding’ van de installateur (of leverancier) krijgt.
Verzoek aan de installateur of de leverancier
• Leg de inhoud van de gebruiksaanwijzing duidelijk uit en overhandig de gebruiksaanwijzing nadien aan de klant.
This Air Conditioner is a new type which adopts a new refrigerant HFC (R410A) instead of the con ventional refrigerant R22 in order to prevent destruction of the ozone layer.
UTILISATION DU NOUVEAU REFRIGERANT
Ce climatiseur est d’un type inédit qui utilise le nouveau réfrigérant HFC (R410A) au lieu du réfrigérant traditionnel
R22, afin d’éviter la destruction de la couche d’ozone.
EINFÜHRUNG EINES NEUEN KÜHLMITTELS
Dies ist ein neuartiges Klimagerät. Anstatt des herkömmlichen Kühlmittels R22 verwendet es das neue oz onschichtschonende HFC Kühlmittel R410A.
ADOZIONE DI UN NUOVO REFRIGERANTE
Questo condizionatore d'aria è di un tipo nuovo che adotta un nuo vo refrigerate HFC (R410A) al posto del
refrigerante convenzionale R22, per prevenire la distruzione dello strato di ozono dell'atmosfera terrestre.
ADOPCIÓN DE NUEVO REFRIGERANTE
Este aparato de aire acondicionado es un modelo reciente que incorpora el nuevo refrigerante HFC (R410A) en
lugar del refrigerante convencional R22 par a así evitar daños en la capa de ozono.
ADOPÇÃO DO NOVO REFRIGERANTE
Este ar condicionado é um modelo novo que adopta um novo refrigerante HFC (R410A) em vez do refrigerante
convencional R22 par a evitar a destruição da cama de ozono.
TOEPASSING VAN EEN NIEUW KOELMIDDEL
Deze airconditioner is een nieuwe type dat werkt met een nieuw koelmiddel HFC (R410A) in plaats van met het
conventionele k oelmiddel R22, als bijdrage om de aantasting van de ozonlaag te reduceren.
• Make sure to ask the qualified installation professional in electric work to install
the air conditioner.
If the air conditioner is inappropriate installed by yourself, it may cause water leak,
electric shock, fire, and so on.
• Be sure to provide grounding.
Do not connect ground wires to gas pipes, water pipes, lightning rods or ground
wires for telephone cables .
CAUTION
TO DISCONNECT THE APPLIANCE FROM THE MAINS SUPPLY
This appliance must be connected to the mains by means of a s witch with a
contact separation of at least 3 mm.
The installation fuse (25A D type ) must be used for the po wer
supply line of this conditioner.
WARNINGS ABOUT OPERATION
• Cleaning of the air filter and other parts of the air filter involv es dangerous work in
high places, so be sure to hav e a service person do it. Do not attempt it yourself.
The cleaning diagram for the air filter is there for the service person, and not for
the customer.
• A void cooling the room too strong or exposing the human body to cool breeze for
a long time as it is bad for the health.
• When you notice something abnormal with the air conditioner (smells like something scorching, poor cooling, etc.), immediately turn off the main switch, the
circuit breaker, from the mains to stop the air conditioner, and contact the dealer .
If the air conditioner is continuously operated with something abnormal, it may
cause machine failure, electric shock, fire, and so on.
WARNINGS ABOUT MOVEMENT AND REPAIR
• Do not mov e or repair any unit by yourself.
Since there is high voltage inside the unit, you may get electric shock when
removing the cover and main unit.
• Whenever the air conditioner needs repair, make sure to ask the dealer to do it.
If it is repaired imperfectly, it may cause electric shock or fire .
• When moving the air conditioner f or re-installing at another place , ask the dealer
to do it. If it is imperfectly installed, it may cause electric shock or fire.
1
CAUTION
CAUTIONS ABOUT INSTALLATION
• Be sure to confirm the following cautions.
• Certainly lay the drain hose for perf ect draining.
Bad drainage may cause flooding in the house and getting furniture
wet.
• Make sure to connect the air conditioner to an exclusive power
supply of the rated voltage, otherwise the unit may break down or
cause a fire.
• Do not install the unit in a place where inflammable gas may leak.
If inflammable gas accumulates around the unit, it ma y cause a fire .
CAUTIONS ABOUT OPERATION
• Carefully read this manual before starting the air conditioner. There
are many important things to keep in mind for daily operation.
• Do not use this air conditioner for special purposes such as preserving food, precision instruments, art objects, breeding animals,
growing potted plants, etc.
• Avoid exposing potted plants and animals to the wind of the air
conditioner, since it badly affects the health and growth of them.
• When the air conditioner is operated with a combustion appliance in
the same place, be careful of ventilation to let fresh air enter the
room.
Poor ventilation causes oxygen shortage.
• Do not place any combustion appliance in a place where it is directly
exposed to the wind of air conditioner, otherwise it may cause
imperfect combustion.
• When the air conditioner is used in a closed room, be careful of
sufficient ventilation of the room. Poor ventilation causes o xygen
shortage.
• Do not touch any switches with wet finger, otherwise you may get an
electric shock.
• If the air conditioner won’t be used for a considerably long time, turn
off the main switch or the circuit breaker, for safety.
• Check the concrete blocks, etc. of the base of the outdoor unit
occasionally.
If the base is left damaged or deteriorated, the unit may topple ov er
and inflict an injury to a person as the worst case.
• Do not put anything on the outdoor unit nor step onto it. If you do so,
it may not only topple ov er the unit but also injure yourself.
• T o make the air conditioner operate in its original performance,
operate it within the range of the operating temperature specified in
the instructions.
Otherwise it may cause a malfunction, or water leak from the unit.
• Prevent any liquid from falling into the remote controller. Do not spill
juice, water or any kind of liquid.
ENGLISH
ITALIANGREEKFRENCHGERMANDUTCHENGLISH
2
PARTS NAME
Indoor unit
Discharge port flange
Connects the discharge duct
Earth screw
Included in the electric parts box
Suction port
Air filter
Removes dust or waste
(Mounted in the suction port)
Outdoor unit
Air inlet (Side and rear)
Remote controller
(Sold separately)
Sucks room air from here
Knob
Opens/Closes the suction port
UNIT No.
R.C.No.
CODE No.
ON / OFF
FAN
MODE
SWING/FIXTIME
VENT
UNITSETCL
FILTERRESET
DATA
SET
TEST
SETTING
H
TEMP.
TIMER SET
TEST
Air outlet
Pipes and electric wires
3
PARTS NAME OF REMOTE CONTROLLER
Display section
All display items are shown in right figure for the explanation.
Only selected contents are displayed in actual operation.
• When turning on the leakage breaker at the first time, [SET D ATA]
flashes on the display part of the remote controller. While this
display is flashing, the model is being automatically confirmed.
Accordingly, wait for a while after [SET D ATA] display has disap-
peared, and then use the remote controller.
169
FILTER
RESET
SET
TEMP.
DATA
TEST
SETTING
UNIT No.
H
TEST
R.C. No.
TIMER SET
CODE No.
Display
section
ON / OFF
FAN
MODE
SWING/FIXTIME
VENT
UNITSET CL
Operation
section
2
1
3
SET
4
5
6
7
15
1
SET DATA display
Displayed during setup a timer.
2
Operation mode display
The selected operation mode is displayed.
3
CHECK display
Displayed while the protective device works
or a trouble occurs.
4
Timer time display
Set time by the timer is displayed.
(When a trouble occurs, the check code is
displayed.)
5
Timer SETIN setup display
When pushing the Timer SET button, the
display of the timer is selected in order of
[OFF] → [OFF] repeat OFF timer
→ [ON]
→ No display.
6
Filter display
If “FILTER ” is displayed, clean the air
filter.
7
UP/DOWN grille display
8
Ventilator operation displa y
9
Flap position display
H
DATA
SETTING
TEST
UNIT No.
R.C.No.
10
11
12
13
14
15
16
10
CODE No.
11
8
12
13
14
SWING display
Displayed during up/down mo vement of the
flap.
Set up temperature display
The selected set up temp. is displayed.
Remote controller sensor display
Displayed while the sensor of the remote
controller is working.
PRE-HEAT display
Displayed when the heating operation starts or
defrost operation is carried out.
While this indication is displayed, the indoor
fan stops or the mode changes in LO W.
No function display
Displayed if there is no function even if the
button is pushed.
Fan mode display
The selected fan mode is displa yed.
(AUTO)
(HIGH)
(MED.)
(LOW)
TEST run display
Displayed during a test run.
4
Operation section
ON / OFF
Push each button to select a desired operation.
• The details of the operation needs to be set up once, the same states are used by pushing
button.
7
1
ON / OFF
TEMP.
10
2
FIL TER
TEST
RESET
5
3
1
Fan mode button
Selects a fan mode.
2
Timer set button
TIMER SET button is used when the timer is
set up.
3
Check button
CHECK button is used for check operation.
During normal operation, do not use this
button.
4
Fan button
FAN button is used when a fan which is sold on
the market or etc. is connected.
• If “No function ” is displayed on the
remote controller when pushing the FAN
button, a fan is not connected.
5
Filter reset button
Resets (Erases) “FILTER ” display.
TIMER SET
ON / OFF
FAN
SWING/FIXTIME
UNITSET CL
8
9
10
FILTER UP/DOWN button
MODE
VENT
button
When the button is pushed, operation starts,
and it stops by pushing the button again.
When the operation stops, the operation lamp
and all displays disappear .
Operation select button
Selects operation mode.
Set up temperature button
Adjusts required room temperature.
Set required set temperature by pushing
or .
(No function display)
8
9
4
6
6
UNIT and AUTO flap button
No function
7
Operation lamp
Lamp is lit during the operation. Lamp is off
when stopped.
It flashes when operating a protection device
or abnormal occurred.
OPTION :
Remote controller sensor
Usually the TEMP. sensor of the indoor unit measures a temperature. A temperature around the
remote controller can also be measured.
For details, contact the dealer from which you have
purchased the air conditioner.
5
CORRECT USAGE
When you use the air conditioner for the first time or when you change SET DATA value, f ollo w the procedure
below. From the next time, the operation will start as set state by pushing the
ON / OFF
button.
Preparation
Turn on the main power switch and/or the leakage breaker.
• When the power supply is turned on, display section is displa yed on the remote controller.
After the power supply is turned on, the remote controller does not accept an operation for approx. 1 minute,
*
but it is not a failure.
REQUIREMENT
• While using the air conditioner, operate it only with
switch and the leakage breaker.
• When starting the operation after stop for a long time, turn on the main power switch for 12 hours or
more before start. (This is required to turn on the compressor case heater f or w arming in order to
prev ent o verload on the compressor when activating the outdoor unit.)
TEMP.
ON / OFF
button without turning off the main power
ON / OFF
1
4
3
2
FIL TER
RESET
TEST
TIMER SET
FAN
SWING/FIXTIME
UNITSET CL
MODE
VENT
1
Push
The operation lamp goes on, and the operation starts.
2
Select an operation mode with the
“MODE
One push of the button, in each time the display
changes in the order shown on the right.
• In HEA T mode, if the room temper ature reaches to the set temperature , the outdoor unit stops and
the air flow becomes LOW and the air v olume decreases .
• In the defrost mode, the fan stops so that cool air
is not discharged and PRE-DEF is displayed.
3
Select air volume with “
One push of the button, in each time the display changes in the order sho wn on the right.
• When air volume is “AUTO ”, air volume differs according to the room temperature.
• In DRY mode, “AUTO ” is displayed and the air v olume is LOW.
• In heating operation, if the room temperature is not heated sufficiently with fan mode “LOW ” oper ation, select “MED. ” or “HIGH ” operation.
4
Determine the set up temperature by pushing the “TEMP. ” or “TEMP. ” button.
ON / OFF
MODE
button.
” button.
FAN
AUTOHEATDRYCOOLFAN
AUTO
” button.
Stop
Push
The operation lamp goes off, and the operation stops.
ON / OFF
button.
LOW MED. HIGH
6
AUTOMATIC OPERATION (Auto Changeover)
When you set the air conditioner in mode or switch over from AUT O oper ation, it will automatically select
either cooling, heating, or fan only operation depending on the indoor room temperature .
TEMP.
ON / OFF
1
3
FIL TER
RESET
TIMER SET
TEST
FAN
SWING/FIXTIME
UNITSET CL
Start
1
2
3
• In case of cooling, start the operation after approx. 1 min ute .
• In case of heating, starts the operation after approximately 3 to 5 minutes.
• When you select the Auto mode, it is unnecessary to set the fan speed.
• After heating operation stops, FAN operation may continue for approx. 30 seconds.
• When the room temperature reaches the set temperature and the outdoor unit stops, the LOW wind is
• If the Auto mode is uncomfortable, you can select the desired conditions manually.
ON / OFF
Push this button to start the air conditioner.
Mode select button (MODE)
Select Auto .
T emperature button
Set the desired temperature.
The fan speed display will sho w and fan speed will be automatically controlled.
discharged and the air volume decreases e xcessively . During defrost operation, the fan stops so that cool
air is not discharged and is displayed.
button
MODE
VENT
2
NOTE
When restarting the operation after stop
• When restarting the operation immediately after stop, the air conditioner does not operate for approx. 3
minutes to protect a compressor.
Stop
Push
Push this button again to stop the air conditioner.
ON / OFF
button.
7
TIMER OPERATION
A type of timer operation can be selected from the following three types .
OFF timer: The operation stops after the set time has passed.
Repeat OFF timer : Every time, the operation stops after the set time has passed.
ON timer: The operation starts after the set time has passed.
Timer operation
1
FIL TER
RESET
1
Push TIMER SET button.
• The timer display (type) changes every
push of the button.
• SET DATA and timer time displays flash.
TEMP.
TEST
TIMER SET
3
4
ON / OFF
FAN
SWING/FIXTIME
UNITSET CL
MODE
VENT
2
OFF
(OFF timer)(Repeat OFF timer)
OFFON
No display
(ON timer)
2
Push
For every push of button, the set time increases in the unit of 0.5 hr (30 minutes).
The maximum set time is 72.0 hr.
For every push of button, the set time decreases in the unit of 0.5 hr (30 minutes).
The minimum set time is 0.5 hr.
3
Push SET button.
•
TIME
to select “SET TIME”.
SETTING
display disappears and timer time displa y goes on.
(When ON timer is activated, timer time, ON timer are displa yed and other displays disappear.)
Clear of timer operation
4
Push CL button.
• TIMER display disappears.
NOTICE
• Once set “Repeat OFF timer” resumes. So start again, stop by same timer.
For cancel timer, push CL button.
8
HINTS FOR ECONOMICAL OPERATION
Maintain room temperature at comfortable level
Clean air filters
Airflow and performance are reduced if the air filters become bloc ked.
Do not open doors and windows more often than necessary
To keep cool or warm air in the room, do not open doors and windows more often than necessary.
Window curtains
In cooling, close the curtains to avoid direct sunlight.
In heating, close the curtains to keep the heat in.
Get uniform circulation of room air
Adjust the air flow direction for the even
circulation of room air.
Clean, please.
Gee, chilly
Control
Blows upward
Cool
and
dry
air
Warm
air
Blows downward
Please close
Air flow adjustment
9
MAINTENANCE
Cleaning of remote controller
CAUTION
• Use a dry cloth to wipe the remote controller.
• A cloth dampened with cold water may be used on the indoor unit if
it is very dirty .
• Never use a damp cloth on the remote controller.
• Do not use a chemically-treated duster for wiping or leave such
materials on the unit for long. It may damage or fade the surface of
the unit.
• Do not use benzine, thinner, polishing powder, or similar solvents for
cleaning. These may cause the plastic surface to crack or deform.
If you do not plan to use the unit for more than 1 month
(1) Operate the fan for 3 to 4 hours to dry inside the unit
Operate “FAN ONLY” mode with set temperature 30°C.
(2) Stop the air conditioner and turn off the main power switch or the
circuit breaker.
Checks before operation
(1) Check that the air filters are installed.
(2) Check that the air outlet or inlet is not blocked.
(3) Turn on the main power s witch or the circuit breaker for the main
power supply to the air conditioner.
Thinner
FAN ONLY operation
WARNING
Cleaning of the air filter and other parts of the air filter involves dangerous work in high places, so be sure
to have a service person do it. Do not attempt it yourself.
NOTE
For Air conditioning system which is operated regularly, cleaning and maintenance of the indoor/outdoor
units are strongly recommended.
As a general rule, if an indoor unit is operated for about 8 hours daily, the indoor/outdoor units will need to
be cleaned at least once every 3-MONTH. This cleaning and maintenance shall be carried out by a
qualified person.
Failure to clean the indoor/outdoor units regularly will result in poor performance, icing, water leaking and
ev en compressor failure.
10
AIR CONDITIONER OPERATIONS AND PERFORMANCE
3 minutes protection function
3-minutes protection function prev ents the air conditioner from starting for initial 3 minutes after the main
power switch/circuit breaker is turned on for re-starting the air conditioner.
Power failure
Po w er failure during operation will stop the unit completely .
• T o restart the operation, push the START/STOP button on the remote controller.
• Lightning or a wireless car telephone operating nearby may cause the unit to malfunction. Turn off the main
power switch or circuit breaker and then turn them on again. Push the START/STOP b utton on the remote
controller to restart.
Heating characteristics
Preheating operation
The air conditioner will not deliver warm air immediately after it is turned on. Warm air will start to flow out
after approximately 5 minutes when the indoor heat exchanger w armed up .
Warm air control (In heating operation)
When the room temperature reaches the set temperature, the fan speed is automatically reduced to prevent
to blow cold draft. At this time, the outdoor unit will stop.
Defrosting operation
If the outdoor unit is frosted during the heating operation, defrosting starts automatically (for approximately
2 to 10 minutes) to maintain the heating capacity.
• The fans in both indoor and outdoor units will stop during the defrosting operation.
• During the defrosting operation, the defrosted water will be drained from the bottom plate of the outdoor
unit.
Heating capacity
In the heating operation, the heat is absorbed from the outside and brought into the room. This w ay of heating
is called heat pump system. When the outside temperature is too low, it is recommended to use another
heating apparatus in combination with the air conditioner .
Attention to snowfall and freeze on the outdoor unit
• In snowy areas, the air inlet and air outlet of the outdoor unit are often covered with snow or frozen up.
If snow or freeze on the outdoor unit is left as it is, it may cause machine failure or poor warming.
• In cold areas, pay attention to the drain hose so that it perfectly drains water without water remaining inside
for freeze prevention. If water freezes in the dr ain hose or inside the outdoor unit, it may cause machine
failure or poor warming.
Air conditioner operating conditions
For proper perf ormance, operate the air conditioner under the f ollo wing temperature conditions:
CoolingOutdoor temperature: –5°C to 43°C (RAV-SM
operation–15°C to 43°C (RAV-SP
Room temperature: 21°C to 32°C (Dry valve temp.), 15°C to 24°C (Wet valve temp.)
∗∗∗
∗∗∗
2AT-E)
2AT-E)
CAUTION
Dry operationOutdoor temperature: 15°C to 43°C (Maximum suction air temp. 46°C)
Room temperature: 17°C to 32°C
HeatingOutdoor temperature: –15°C to 15°C (Wet valve temp.)
operation
If air conditioner is used outside of the above conditions, safety protection may work.
Room temperature: 15°C to 28°C (Dry valve temp.)
Room relative humidity – less than 80 %. If the air conditioner operates
in excess of this figure, the surface of the air conditioner may cause dewing.
11
RE-INSTALLATION
DANGER
Ask the dealer or an installation professional to re-install the air conditioner to a new place or
move it to another place and to observe the following items.
If the air conditioner is inappropriate installed by yourself, it may cause electric shoc k or fire.
Do not install the air conditioner in the following places
• Do not install the air conditioner in any place within 1 m from a TV, stereo, or radio set. If the unit is installed
in such place, noise transmitted from the air conditioner affects the operation of these appliances .
• Do not install the air conditioner near a high frequency appliance (sewing machine or massager for business
use, etc.), otherwise the air conditioner may malfunction.
• Do not install the air conditioner in a humid or oily place, or in a place where steam, soot, or corrosive gas is
generated.
• Do not install the air conditioner in a salty place such as seaside area.
• Do not install the air conditioner in a place where a great deal of machine oil is used.
• Do not install the air conditioner in a place where it is usually exposed to strong wind such as in seaside
area or on the roof or upper floor of a building.
• Do not install the air conditioner in a place where sulfureous gas generated such as in a spa.
• Do not install the air conditioner in a vessel or mobile crane.
Be careful with noise or vibrations
• Do not install the air conditioner in a place where noise by outdoor unit or hot air from its air outlet annoys
your neighbors.
• Install the air conditioner on a solid and stable foundation so that it prevents transmission of resonating,
operation noise and vibration.
• If one indoor unit is operating, some sound may be audible from other indoor units that are not operating.
TROUBLES AND CAUSES
CAUTION
If any of the following conditions occur, turn off the main power supply switch and immediately contact the
dealer :
• The operation lamps flash at short intervals (5 Hz) e ven though you have tried turning off the power
supply and turning on again after 2 or 3 minutes.
• Switch operation does not work properly.
• The main power fuse often blows out, or the circuit breaker is often activated.
• A foreign matter or water fall inside the air conditioner.
• Any other unusual conditions are observed.
12
Before you ask f or servicing or repair s, check the following points.
Inoperative
• The main power switch is turned off.
• The circuit breaker is activated to cut off power supply.
• The main power fuse has blown out.
• Stoppage of electric current.
Does not cool well or heat well
• The air inlet and/or outlet of the outdoor unit is blocked.
Recheck
• Doors or windows are opened.
• The fan speed is set to low.
• The air conditioner is set in the DRY mode.
• The set temperature is too high. (In cooling operation)
• The set temperature is too low. (In heating operation)
Indoor unit or outdoor unit makes a strange noise.
• When the temperature suddenly changes, the indoor or outdoor unit
occasionally makes a strange noise because of changing of refrigerant flow or
expansion work.
The room air is smelly or a bad odor comes from the air conditioner.
• Smells impregnated in the walls‚ carpets, furniture, clothing, or furs, come
out from the air conditioner.
Outdoor unit is frosted in heating operation.
Water drains from outdoor unit.
• The outdoor unit is sometimes frosted in heating operation.
In that case, the unit automatically performs defrosting
(for 2 to 10 minutes) for increasing the heating efficiency.
• In defrosting operation, both the indoor and outdoor units stop air flow.
• Hiss sound is heard when flow of the refrigerant is changed for defrosting.
• Resultant water of automatic defrosting in heating operation drains from
outdoor unit.
Air flow changes without FAN button set to AUTO mode .
These are not failures.
• When the temperature of blown air drops in heating operation,
the air conditioner automatically changes or stops air flow from the
indoor unit not to make persons in the room feel chilly.
• Air flow of the indoor unit is occasionally changed in the cooling operation.
A white mist of chilled air or water is generated from the outdoor unit.
• The indoor unit in cooling operation or the outdoor unit in defrosting
operation occasionally cause steams.
Calm
13
TROUBLES AND CAUSES (Concerning Remote Controller)
Before you ask for servicing or repairs, check the following points:
Setting Change is Impossible
Symptoms
The fan speed can not be
changed.
Causes
• Check whether the MODE indicated on the display is “AUTO”.
AUTO
• Check whether the MODE indicated on the display is “DRY”.
(DRY)
Reason and Disposal
When the automatic mode is selected, the air conditioner automatically selects the fan speed.
When dry operation is selected, the
air conditioner automatically selects
the fan speed.
14
This product is compliant with Directive 2002/95/EC , and cannot be disposed as unsorted municipal waste.
Ce produit est conforme à la Directive 2002/95/CE et il ne peut pas être jeté avec les ordures ménagères non triées.
Dieses Produkt entspricht der Richtlinie 2002/95/EWG und darf nicht als normaler, unsortierter Hausabfall entsorgt
werden.
Questo prodotto è conforme alla direttiva 2002/95/CE, e per disfarsene non deve essere gettato con la spazzatura della
casa.
Este producto cumple con la Directiva 2002/95/EC, y no se puede desechar como la basur a m unicipal.
Este produto respeita a Directiva 2002/95/EC e não pode ser deitado fora como lixo municipal.
Dit product is in overeenstemming met richtlijn 2002/95/EC en mag niet als huishoudelijk afval worden afgevoerd.