Toshiba RAS-13UKP-ES, RAS-13UA-ES, RAS-07UA-ES, RAS-10UKP-ES, RAS-10UA-ES Service Manual

SERVICE MANUAL

AIR-CONDITIONER

SPLIT WALL TYPE

FILE NO. SVM-02005(2)

10/13 Class

Revised on January, 2005

07 Class

RAS-13UKP-ES / RAS-13UA-ES
RAS-10UKP-ES / RAS-10UA-ES
RAS-07UKP-ES / RAS-07UA-ES

– 1 –

FILE NO. SVM-02005(1)

CONTENTS

1. SPECIFICATIONS

2. CONSTRUCTION VIEWS

2-1 Indoor Unit
2-2 Outdoor Unit (RAS-13UA-ES)
2-3. Outdoor Unit (RAS-10UA-ES)
2-4. Outdoor Unit (RAS-07UA-ES)

3. WIRING DIAGRAM

4. SPECIFICATION OF ELECTRICAL PARTS

4-1 Indoor Unit
4-2 Outdoor Unit (RAS-13UA-ES)
4-3 Outdoor Unit (RAS-10UA-ES, RAS-07UA-ES)

5. REFRIGERATION CYCLE DIAGRAM

5-1 RAS-13UKP-ES / RAS-13UA-ES
5-2 RAS-10UKP-ES / RAS-10UA-ES
5-3 RAS-07UKP-ES / RAS-07UA-ES

6. CONTROL BLOCK DIAGRAM

7. OPERATION DESCRIPTION

7-1 Outline of Air Conditioner Control
7-2 Description of Operation Circuit
7-3 Hi POWER Mode
7-4 High-Temperature Limit Control
7-5 Low-Temperature Limit Control
7-6 Auto Restart Function

7-7 Filter Check Lamp

8. INSTALLATION PROCEDURE

8-1 Safety Cautions
8-2 Installation Diagram of Indoor and Outdoor Units
8-3 Installation
8-4 Indoor Unit
8-5 Outdoor Unit
8-6 How to Set Remote Control Selector Switch
8-7 Others

9. TROUBLESHOOTING CHART

9-1 Troubleshooting Procedure
9-2 Basic Check Items
9-3 Primary Judgement
9-4 Self-Diagnosis by Remote Control (Check Code)
9-5 Troubleshooting Flowcharts
9-6 Troubleshooting for Remote Control (Including The Indoor P.C. Board)

– 2 –

FILE NO. SVM-02005(1)

10. PARTS REPLACEMENT

10-1 Indoor Unit
10-2 Outdoor Unit (RAS-13UA-ES)
10-3 Outdoor Unit (RAS-10UA-ES)
10-4 Outdoor Unit (RAS-07UA-ES)

11. EXPLODED VIEWS AND PARTS LIST

11-1 Indoor Unit (E-Parts Assy)
11-2 Indoor Unit
11-3 Outdoor Unit (RAS-13UA-ES)
11-4 Outdoor Unit (RAS-10UA-ES)
11-5 Outdoor Unit (RAS-07UA-ES)

• This air conditioner is charged with HFC
(R-410A) that doesn’t deplete the
Ozone layer.

• This air conditioner requires special
installation for the refrigerant R-410A.

– 3 –

FILE NO. SVM-02005(1)

MODEL RAS-13UKP-ES RAS-10UKP-ES RAS-07UKP-ES

RAS-13UA-ES RAS-10UA-ES RAS-07UA-ES

ITEM Cooling

Capacity

220V 240V 220V 240V 220V 240V

kW 3.70 3.75 2.65 2.70 2.15 2.18

Phase 1∅

Power source V 220 – 240

Hz 50
Power consumption kW 1.25 1.29 0.77 0.83 0.66 0.68
Pow er factor % 98 95 92 92 97 90
Running Indoor A 0.15
current Outdoor A 5.66 5.53 3.65 3.60 2.95 3.00
Starting current A 24 16 12
Moisture removal lit/h 2.0 1.2 0.8

Noise

Indoor (H/M/L) dB 41/35/31 39/33/26 38/32/26
Outdoor (220-240V) dB 46 47 46 47 44 45

Refrigerant

Name of refrigerant R-410A
Rated amount kg 0.86 0.65 0.65

Refrigerant control Capillary tube

Gas side size mm ∅9.52
Connection type Flare connection
Liquid side size mm ∅6.35

Interconnection

Connection type Flare connection

pipe

Maximum length

m 15*

1

10*

1

(One way)
Maximum height

m6 5

difference

INDOOR UNIT RAS-13UKP-ES RAS-10UKP-ES RAS-07UKP-ES

Height mm 275

Dimensions Width mm 790

Depth mm 208
Net weight kg 10
Evaporator type Finned tube
Indoor fan type Cross flow fan

High fan m3/h 630 630 570
Air volume Medium fan m3/h 550 490 460

Low fan m3/h 460 370 340
Fan motor output W 30
Air filter Honeycomb woven filter with PP frame

OUTDOOR UNIT RAS-13UA-ES RAS-10UA-ES RAS-07UA-ES

Height mm 538 530 530
Dimensions Width mm 780 770 660

Depth mm 300 200 240
Net weight kg 39 29 27
Condenser type Finned tube
Outdoor fan type Propeller fan
Airflow volume m3/h 1700 1900 1500 1700 1420 1520
Fan motor output W 30

Compressor

Model PA150X2T-4FM PA98X1T-4FZ PA79X1T-4FZ5

Output W 1100 750 605
Safety device Fuse, Overload relay
Louver type Automatic louver
Usable outdoor temperature range °C 21 ~ 43

1. SPECIFICATIONS

– 4 –

FILE NO. SVM-02005(1)

Note : 1

• Capacity is based on the following temperature conditions.

Note : 2

• Charge refrigerant according to the table below.

Refrigerant RAS-13UKP-ES / RAS-13UA-ES

RAS-10UKP-ES / RAS-10UA-ES
RAS-07UKP-ES / RAS-07UA-ES

*1 No need to charge

15m or less 10m or less

refrigerant

Temperature

Condition

JIS C9612-1994

Cooling

Indoor unit inlet air temperature

(DB) 27°C

(WB) 19°C

Outdoor unit inlet air temperature

(DB) 35 °C

(WB) 24 °C

– 5 –

FILE NO. SVM-02005(1)

2. CONSTRUCTION VIEWS

2-1. Indoor Unit

Knock out system

Back body

Front panel

Air outlet

Air inlet

Air filter

Heat exchanger

Knock out system

660

275

790

208

48

48

26

4519040

32

64

590

320

620

235 235

215 215

9090

275

45

150150 160160

120 80

53

660

Hanger

Hanger

Hanger

Hanger

Hanger

Drain hose (0.54m)

Connecting pipe (0.43m)
(Flare ∅6.35)

For stud bolt
(∅8~∅10)

For stud bolt (∅6)

Installation plate outline

Center line

Minimum
distance
to ceiling

170 or more

Minimum
distance
to ceiling

170 or more

65 or more

Minimum
distance
to ceiling

Wireless remote control

57 18

160

Flare (∅9.52)

Connecting pipe (0.33m)

– 6 –

FILE NO. SVM-02005(1)

2-2. Outdoor Unit (RAS-13UA-ES)

538

325

325

52.5

23

301

325

300

Handle

∅25Drain outlet

Electric parts cover

Service
port

61

54

325 (pitch)

(8.5)

(8.5)

342

100 or more

100 or more

600 or more

600 or more

Installation dimension

600

Air inlet

Air outlet

8-∅6 hole (for fixing outdoor unit)

Liquid side (Flare ∅6.35)

Gas side (Flare ∅9.52)

120

∅11x14 hole

∅6 hole

R10

600

Detail Drawing

50
36

A

A

4-∅11x14 hole (for ∅8-∅10 anchor bolt)

600

100

130

780

90

59

27

Fan guard

∅420

Z

View

Z

4x∅11x14 Long holes (for ∅8-∅10 anchor bolt)

– 7 –

FILE NO. SVM-02005(1)

2-3. Outdoor Unit (RAS-10UA-ES)

600 85

36

111

∅25 Drain hole

50

30

216

230

8-∅6 Holes
(For fixing the outdoor unit)

4-∅11x14 Long holes
(For anchor bolt ∅8-∅10)

Gas side (flare ∅9.52)

Liquid side (flare ∅6.35)

111

A

600

R10

50

36

25

216

230

∅11x14 Hole

∅6 Hole

Handle

11

525

530

5

268

Fan guard

∅420

770

59

89

200

11

12

Electric
parts cover

Z

54 62

Access for
charging

250

Z

View
600

45 or more

Air inlet

600 or more

(Minimum distance
of the wall)

4-∅11x14 Long holes

400 or more

Air
outlet

Center
port

230

100 or more

Air inlet

Visible outline of the product

A

Detail Drawing

Mounting dimension of anchor bolt

268

770

59

89

(For anchor bolt ∅8-∅10)

– 8 –

FILE NO. SVM-02005(1)

2-4. Outdoor Unit (RAS-07UA-ES)

Z

Cover PV

54

273.5

59.5

∅420

500 97.5

(11)

297

(12.5)273.5 (pitch)

660

242

56

A Detail Drawing (Back Leg)

660

50
36

R 15

R 5.5

273.5

265

∅6 Hole

B Detail Drawing (Front Leg)

50

36

R 15

660

265

273.5

∅6 Hole

∅11x14 Hole

A

B

Z View

97

∅25Drain outlet

2-∅11x14 hole
(for ∅8-∅10 anchor bolt)

Fan guard

530

Liquid side

(Flare ∅6.35)
Gas side
(Flare ∅9.52)

Service port

126

48

325

100 or more

100 or more

600 or more

600 or more

Installation dimension

600

Air inlet

Air outlet

4x∅11x14 Long holes (for ∅8-∅10 anchor bolt)

– 9 –

FILE NO. SVM-02005(1)

3. WIRING DIAGRAM

CN13

CN07

BLK

GRN&YEL

POWER
TERMINAL
BLOCK

POWER SUPPLY
SINGLE PHASE
220-240V ,
50 Hz

BRW

BLU

BLK

WHI

GRN&YEL

OUTDOOR
TERMINAL
BLOCK

INDOOR
TERMINAL
BLOCK

WHI

DSA

VARISTOR

RY01

4

3

F01

C15

L01

IC03

C58

R48

R46

R47

CR03

D38

C01 R01

DB01

POWER
SUPPLY
CIRCUIT

C02

DC 12V
DC 5V

R21
VARISTOR

MAIN P.C. BOARD

MCC-862

T6.3A
250V

P04

SG01

CN04

INDOOR

OUTDOOR

1 2

1 2

CAPACITOR

CAPACITOR

RED

RED

RED

WHI

WHI

BLKCBLK

BLK

GRN & YEL
CHASSIS

RED

FAN MOTOR

R

S

YEL

135

GRY

BRW

BLK

WHI

RED

CN01CN03

THERMO

SENSOR

(TA)

HEAT

EXCHANGER

SENSOR

(TC)

CN10CN11

AC FAN MOTOR

BLK

BLK

1

35

1

35

24
24

6
6

1

3

5

1

3

5

1

2

1

2

3
3

112

2

BLK

BLK

112

2

:
:
:
:
:
:
:
:
:

:

:

BROWN
RED
WHITE
YELLOW
BLUE
BLACK
GRAY
PINK
ORANGE
GREEN &
GREENGRN

YELLOW

BRW

RED

WHI
YEL
BLU
BLK

GRY

PNK

ORN

GRN&YEL

COLOR IDENTIFICATION

BLU

BLU

BLU

BLU

BLU

BLU

BLU

BLU

BLU

BLU

WHI

YEL

CN25

PNK

PNK

YEL

YEL

YEL

WHI

INFRARED RAYS RECEIVE
AND INDICATION PARTS

4 5 6 7 8 9

10 11

3

1

2

4 5 6 7 8 9

10 11

3

1

2

4 5 6 7 8 9

10 11

3

1

2

2 1

3

5

4

2 1

3

5

4

1

2

1

2

R22

N

L

Louver motor

GRN&YEL

– 10 –

FILE NO. SVM-02005(1)

4. SPECIFICATION OF ELECTRICAL PARTS

4-1. Indoor Unit

No. Parts name Type Specifications

1 Fan motor (for indoor) MMF-240-20-4A-1 AC Motor with 135°C thermo fuse
2 Thermo sensor (TA-sensor) ——— 10kΩ at 25°C
3 Switching transformer (T01) SWT-47
4 Microcontroller unit (IC30) TMP87CM40AN-2C67
5 Heat exchanger sensor

——— 10kΩ at 25°C

(TC-sensor)
6 Line filter (L01) LC*SS11V-06270 27mH, 600mA
7 Bridge rectifier (DB01) D3SBA60 4A, 600V
8 Capacitor (C02) KMH400VSSN47M22S 47µF, 400V
9 Fuse (F01) TSCR6.3A T6.3A, 250VAC

10 Varistor (R21, R22) 15G561K 560V
11 Resistor (R01) RF-2TK5R6 5.6Ω, 2W
12 Louver motor MP24GA 12VDC
13 Relay (Comp., RY01) DI12D1 Rating 20A/AC250V, 12VDC

4-2. Outdoor Unit (RAS-13UA-ES)

No. Parts name Type Specifications

Output (Rated) 1100W , 2poles , 1 phase , 220 – 240V, 50Hz

1 Compressor PA150X2T-4FM Winding resistance (Ω) C-R C-S

(at 20°C) 2.49 3.95
Output (Rated) 30W, 6poles, 1 phase, 220 – 240V, 50Hz

2 Fan motor (for outdoor) HF-240-30B Winding resistance (Ω) Red-Black White-Black

(at 20°C) 245 388

3

Running capacitor

SK-50FMP1.5U2 AC 500V, 1.5µF

(for fan motor)
4

Running capacitor

DS371356CPNB AC 370V, 35µF

(for compressor)

– 11 –

FILE NO. SVM-02005(1)

No. Parts name Type Specifications

Output (Rated) 750W , 2poles, 1 phase, 220 – 240V, 50Hz

1 Compressor Winding resistance (Ω) C-R C-S

(at 20°C) 3.81 5.09
Output (Rated) 605W , 2poles, 1 phase, 220 – 240V, 50Hz
Winding resistance (Ω) C-R C-S
(at 20°C) 4.80 8.37
Output (Rated) 30W, 6poles, 1 phase, 220 – 240V, 50Hz

2 Fan motor (for outdoor) HF-240-30B Winding resistance (Ω) Red-Black White-Black

(at 20°C) 245 388

3

Running capacitor

SK-50FMP1.5U2 AC 500V, 1.5µF

(for fan motor)

DS371256CPNB

AC 370V, 25µF

4

Running capacitor (RAS-10UA-ES)

(for compressor) DS371156CPNB

AC 370V, 15µF

(RAS-07UA-ES)

4-3. Outdoor Unit (RAS-10UA-ES, RAS-07UA-ES)

PA98X1T-4FZ

(RAS-10UA-ES)

PA79X1T-4FZ5

(RAS-07UA-ES)

– 12 –

FILE NO. SVM-02005(1)

Note :

• Measure the heat exchanger temperature at the center of U-bend. (By means of TC sensor)

Standard 0.95 10.0 High 27/19 35/24

Cooling Overload 1.15 13.0 High 32/23 43/26

Low temperature 0.65 2.0 Low 21/15 21/15

50Hz

Fan speed

(indoor)

Ambient temp.

conditions DB/WB

(°C)

Indoor Outdoor

Standard

pressure P

(MPaG)

Surface temp. of heat

exchanger interchanging

pipe T1 (°C)

5. REFRIGERATION CYCLE DIAGRAM

5-1. RAS-13UKP-ES / RAS-13UA-ES

Heat exchanger

Indoor unit

Cross flow fan

Cooling

Cooling

Compressor

Condenser

Propeller fan
Outdoor unit

Capillary tube

∅1.5x900S

PA150X2T-4FM

Cooling

Mark( )means check points of Gas Leak.

O.D.:9.52mm O.D.:6.35mm

Cooling

Packed valve

(∅9.52)

Packed valve

(∅6.35)

0.39m
(Connecting pipe)
∅9.52

0.49m
(Connecting pipe)
∅6.35

T1

P

Refrigerant
R-22 : 0.86 kg.

– 13 –

FILE NO. SVM-02005(1)

5-2. RAS-10UKP-ES / RAS-10UA-ES

Note :

• Measure the heat exchanger temperature at the center of U-bend. (By means of TC sensor)

Standard 0.86 12.0 High 27/19 35/24

Cooling Overload 1.12 18.0 High 32/23 43/26

Low temperature 0.61 2.0 Low 21/15 21/15

50Hz

Fan speed

(indoor)

Ambient temp.

conditions DB/WB

(°C)

Indoor Outdoor

Standard

pressure P

(MPaG)

Surface temp. of heat

exchanger interchanging

pipe T1 (°C)

Indoor unit

Cross flow fan

Cooling

Cooling

Compressor

Condenser

Propeller fan

Outdoor unit

PA98X1T-4FZ

Cooling

Mark( )means check points of Gas Leak.

O.D.:9.52mm O.D.:6.35mm

Cooling

Packed valve

(∅9.52)

Packed valve

(∅6.35)

0.39m
(Connecting pipe)
∅9.52

0.49m
(Connecting pipe)
∅6.35

T1

P

Refrigerant
R-22 : 0.65 kg.

Evaporator

Capillary tube

∅1.5x1200S

– 14 –

FILE NO. SVM-02005(1)

5-3. RAS-07UKP-ES / RAS-07UA-ES

Note :

• Measure the heat exchanger temperature at the center of U-bend. (By means of TC sensor)

Standard 0.97 14.0 High 27/19 35/24

Cooling Overload 1.13 20.0 High 32/23 43/26

Low temperature 0.63 2.0 Low 21/15 21/15

50Hz

Fan speed

(indoor)

Ambient temp.

conditions DB/WB

(°C)

Indoor Outdoor

Standard

pressure P

(MPaG)

Surface temp. of heat

exchanger interchanging

pipe T1 (°C)

Indoor unit

Cross flow fan

Cooling

Cooling

Compressor

Condenser

Propeller fan

Outdoor unit

PA79X1T-4FZ5

Cooling

Mark( )means check points of Gas Leak.

O.D.:9.52mm O.D.:6.35mm

Cooling

Packed valve

(∅9.52)

Packed valve

(∅6.35)

0.39m
(Connecting pipe)
∅9.52

0.49m
(Connecting pipe)
∅6.35

T1

P

Refrigerant
R-22 : 0.65 kg.

Evaporator

Capillary tube

∅1.2x650S

– 15 –

FILE NO. SVM-02005(1)

6. CONTROL BLOCK DIAGRAM

REMOTE CONTROL

Remote Control

Operation (START/STOP)
Operation Mode Selection

AUTO, COOL, DRY, FAN ONLY

Temperature Setting
Fan Speed Selection

ON TIMER Setting

OFF TIMER Setting

Louver Auto Swing

Louver Direction Setting

ECO

Hi power

Filter Reset

Infrared Rays

Heat Exchange sensor

Main Unit Control Panel M.C.U.

Functions

Operation

Display

Timer

Display

Filter Sign

Display

Hi Power

Sign Display

Fan Only

Sign Display

Indoor Fan

Motor

Louver

Motor

Louver

ON/OFF

Signal

Compressor

ON/OFF

Signal

Power Supply

Circuit

Noise Filter Relay Driver, Louver Driver

Relay

RY01

220-240 V~, 50Hz

Compressor, Outdoor Fan Motor

Initiallizing Circuit

Clock Frequency
Oscillator Circuit

• Louver Control

• 3-minutes Delay at Restart

for Compressor

• Processing
(Temperature Processing)

• Motor Revolution Control

• Timer

Thermo. Sensor

Infrared Rays Signal Reciver

– 16 –

FILE NO. SVM-02005(1)

7. OPERATION DESCRIPTION

7-1-1. Louver control

(1)Vertical air flow louver

Position of veritcal air flow louver is automatically
controlled according to the operation mode.
Besides, position of vertical air flow louver can be
arbitrarily set by pressing [FIX] button.
The louver position which is set by [FIX] button is
stored in the microcontroller, and the louver is
automatically set at the stored position for the next
operation.

(2)Swing

If [SWING] button is pressed when the indoor unit is
in operation, the vertical air flow louver starts
swinging. When [FIX] button is pressed, it stops
swinging.

7-1-2. Indoor fan control (AC fan motor)

(1)The indoor fan is operated by the stepless speed

change AC motor.

(2)For air flow level, speed of the indoor fan motor is

controlled in five steps (LOW, LOW

+

, MED, MED

+

and HIGH). If AUTO mode is selected, the fan
motor speed is automatically controlled by the
difference between the preset temperature and the
room temperature.

Table 7-1-1

7-1. Outline of Air Conditioner Control

This is a fixed capacity type air conditioner, which uses
a AC motor for an indoor fan. The AC motor drive
circuit is mounted in the indoor unit. And electrical
parts which operate the compressor and the outdoor
fan motor, are mounted in the outdoor unit.
The air conditioner is mainly controlled by the indoor
unit controller. The controller operates the indoor fan
motor based upon commands transmitted by the
remote control and transfers the operation commands
to the outdoor unit controller.
The outdoor unit controller receives operation
commands from the indoor unit, and operates the
outdoor fan motor and the compressor.

(1) Role of indoor unit controller

The indoor unit controller receives the operation

commands from the remote control and executes
them.

• Temperature measurement at the air inlet of the
indoor heat exchanger by the indoor
temperature sensor

• Temperature setting of the indoor heat
exchanger by the heat exchanger sensor

• Louver motor control

• Indoor fan motor operation control

• LED display control

• Transferring of operation commands to the

outdoor unit

• Receiving of information of the operation status
and judging of the information or indication of
error

LOW

+

=

MED+=

LOW+MED

2

MED+HIGH

2

RAS-13UKP-ES RAS-10UKP-ES RAS-07UKP-ES

Model Motor speed Air flow level Motor speed Air flow level Motor speed Air flow level

(rpm) (m3/h) (rpm) (m3/h) (rpm) (m3/h)

HIGH 1,300 630 1,300 630 1,200 570
Cooling MED+ 1,220 600 1,180 560 1,100 520
and MED 1,150 550 1,050 490 1,000 460
Fan only LOW+ 1,070 500 950 430 900 400

LOW 1,000 460 850 370 800 340

– 17 –

FILE NO. SVM-02005(1)

7-2. Description of Operation Circuit

(1) When turning on the breaker, the operation lamp

blinks. This means that the power is on (or the
power supply is cut off.)

(2) When pressing [START / STOP] button on the

remote control, receiving beep sounds from the
indoor unit, and the next operation is performed
together with opening the vertical air flow louver.

(3) Once the operation mode is set, it is memorized in

the microcontroller so that the previous operation
can be effected thereafter simply by pressing
[START / STOP] button.

7-2-1. Fan only operation

([MODE] button on the remote control is set
to the fan only operation.)

(1) When [FAN] button is set to AUTO, the indoor fan

motor operates as shown in Fig. 7-2-1. When
[FAN] button is set to LOW, LOW+, MED, MED+ or
HIGH, the motor operates with a constant air flow.

NOTE :

*1: The values marked with *1 are calculated and

controlled by the difference in motor speed
between M+ and L–.

Fig. 7-2-1 Setting of air flow [FAN:AUTO]

(2) The Hi POWER operation cannot be set.

7-2-2. Cooling operation

([MODE] button on the remote control is set
to the cooling operation.)

(1) The compressor, outdoor fan and operation

display on the remote control are controlled as
shown in Fig. 7-2-2.

Fig. 7-2-2

(2) When [FAN] button is set to AUTO, the indoor fan

motor operates as shown in Fig. 7-2-3. When
[FAN] button is set to LOW, LOW+, MED, MED+ or
HIGH, the motor operates with a constant air flow.

NOTE :

*1: The values marked with *1 are calculated and

controlled by the difference in motor speed
between M+ and L–.

Fig. 7-2-3 Setting of air flow [FAN:AUTO]

+2

+2.5

+3

+1.5
+1
+0.5
0

M+

*1
*1
*1
L-

(Room temp.) — (Preset temp.)

Preset
temp.

0.5

0

Preset
temp.

ON ON

OFFOFF ON

Compressor

Outdoor fan

OPERATION

display

(Room temp.) — (Preset temp.)

*1
*1
*1

L-

+3
+2.5
+2
+1.5
+1
+0.5

-0.5

0

M+

(Room temp.) — (Preset temp.)

Preset
temp.

– 18 –

FILE NO. SVM-02005(1)

7-2-4. Automatic operation

([MODE] button on the remote control is set
to the automatic operation.)

(1) One of 2 operations (Cooling, Fan only) is

selected according to difference between the
preset temperature and the room temperature at
which the automatic operation has started, as
shown in Fig. 7-2-6. The Fan only operation
continues until the room temperature reaches a
level at which another mode is selected.

(2) Temporary Auto

When the TEMPORARY button on the indoor unit
is pushed, the preset temperature is fixed at 24°C
and the indoor unit is controlled as shown in
Fig. 7-2-6.

Fig. 7-2-6

7-2-3. Dry operation

([MODE] button on the remote control is set
to the dry operation.)

(1) The compressor, outdoor fan and operation

display on the remote control are controlled as
shown in Fig. 7-2-4.

Fig. 7-2-4

(2) The microcontroller turns the compressor on and

off at the regular intervals (4 to 6 minutes). While
the compressor is turning off, the indoor fan motor
operates in the SUPER LOW position.

The pattern of operation depending on the relation

between room temperature and preset
temperatures is shown in Fig. 7-2-5.

Fig. 7-2-5

(3) [FAN] button on the remote control is set to AUTO

only.

(4) The Hi POWER operations cannot be set.

Preset
temp.

ON

+3

+2

+1

0

OFF

Outdoor fan

OPERATION

display

Compressor

ON:6min.

OFF:4min.

ON:5min.

OFF:5min.

OFF

ON:6min.

OFF:4min.

ON:5min.

OFF:5min.

(Room temp.)

—

(Preset temp.)

Room temp.

Preset temp.+1
Preset temp.

Compressor
Outdoor fan

Indoor fan

L.*S.L. S.L.L. L. S.L. L.

ON ON ON ON

OFF OFF OFF

*

Super Low

+4

0

(Room temp.) – (Preset temp.)

°C

Cooling operation

The louver moves to the position same
as Hi POWER operation.

Cooling operation

Fan only operation

RAS-13UKP-ES
RAS-10UKP-ES
RAS-07UKP-ES

– 19 –

FILE NO. SVM-02005(1)

7-3. Hi POWER Mode

([Hi POWER] button on the remote
control is pressed.)

When [Hi POWER] button is pressed while the indoor
unit is in Auto, Cooling, Hi POWER mark is indicated
on the display of the remote control and the unit
operates as follows.

(1) Automatic operation

• The indoor unit operates in according to the
current operation.

(2) Cooling operation

• The preset temperature drops 3°C.
(The value of the preset temperature on the
remote control does not change.)

• If the difference between the preset
temperature and the room temperature is big,
the horizontal louver moves to the Hi POWER
position automatically. Then when the difference
between them gets smaller, the horizontal
louver returns automatically.

• FAN speed : [AUTO]
If the difference between the preset
temperature and room temperature is big, the
air conditioner operates at maximum airflow
level. If the difference between the preset
temperature and the room temperature is small,
the air conditioner operates at normal airflow
level.

• FAN speed : One of 5 levels
The air conditioner operates at normal airflow
level.

(3) The Hi POWER mode can not be set in Dry or Fan

only operation.

7-4. High-Temperature Limit Control

The microcontroller detects the indoor heat exchanger
temperature to prevent pressure of a refrigerating cycle
from increasing excessively.
The compressor and outdoor fan motor are controlled
as shown in Fig. 7-4-1.

Fig. 7-4-1

7-5. Low-Temperature Limit Contr ol

The microcontroller detects the indoor heat exchanger
temperature to prevent the indoor heat exchanger from
freezing.
The compressor and outdoor fan motor are controlled
as shown in Fig. 7-5-1 and 7-5-2.

RAS-13UKP-ES

Fig. 7-5-1

RAS-10UKP-ES ;RAS-07UKP-ES

Fig. 7-5-2

60

53
52

Compressor

Outdoor fan

OFF

OFF

ON

ON

OFF

ON

Heat exchanger
temp.

6

2

Compressor Outdoor fan

ON

Less than continues

for 5 minutes

OFF

Heat exchanger
temperature

7

5

Compressor

Heat exchanger
temperature

Outdoor fan

ON

Less than continues

for 5 minutes

OFF