Toshiba PSA10 User Manual

TOSHIBA
Satellite A10 Series
Port able Personal Computer
User ’s Manual

Copyright

© 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the informa­tion contained herein.
TOSHIBA Satellite A10 Series Portable Personal Computer User’s Manual
First edition April 2003
Copyright authority for music, movies, computer programs, data bases and other intellectual property covered by copyright laws belongs to the author or to the copyright owner . Copyrighted material can be repro­duced only for personal use or use within the home. Any other use beyond that stipulated above (including conversion to digital format, alteration, transfer of copied material and distribution on a network) without the permission of the copyright owner is a violation of copyright or author’s rights and is subject to civil damages or criminal action. Please comply with copyright laws in making any reproduction from this manual.

Disclaimer

This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA Satellite A10 Series Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manual.

Trademarks

Intel, Intel Speed Step, Pentium and Celeron are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries/ regions. Windows and Microsoft are registered trademarks of Microsoft Corporation. Photo CD is a trademark of Eastman Kodak.

FCC information

Product Name : Model number :
Satellite A10
PSA10
FCC notice "Declaration of Conformity Information"
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa­tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer­ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripher­als or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, USB port, parallel port and microphone jack. Changes or modifications made to this equipment, not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment.
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Contact
Address: TOSHIBA America Information Systems, Inc.
9740 Irvine Boulevard Irvine, California 92618-1697
Telephone: (949) 583-3000
EU Declaration of Conformity information
TOSHIBA declares, that the product: PSA10 conforms to the following Standards: Supplementary Information: “The product complies with the requirements
of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.”
This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
VCCI Class B Information

Modem warning notice

Conformity Statement
The equipment has been approved to [Commission Decision “CTR21”] for pan­European single terminal connection to the Public Switched Telephone Network (PSTN).
However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
In the event of problems, you should contact your equipment supplier in the first instance.
Network Compatibility Statement
This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional require­ments conditional in EG 201 121.
Germany ATAAB AN005,AN006,AN007,AN009,AN010 and
DE03,04,05,08,09,12,14,17 Greece ATAAB AN005,AN006 and GR01,02,03,04 Portugal ATAAB AN001,005,006,007,011 and P03,04,08,10 Spain ATAAB AN005,007,012, and ES01 Switzerland ATAAB AN002 All other countries/regions ATAAB AN003,004 Specific switch settings or software setup are required for each network, please refer
to the relevant sections of the user guide for more details. The hookflash (timed break register recall) function is subject to separate national
type approvals. It has not been tested for conformity to national type regulations, and no guarantee of successful operation of that specific function on specific national networks can be given.
Telephone company procedures
The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.
If problems arise
If any of your telephone equipment is not operating properly, you should immedi­ately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discon­tinue service. When practical, they will notify you in advance of this disconnection. If advance notice is not feasible, you will be notified as soon as possible. When you are notified, you will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
Disconnection
If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.
Fax branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other entity or individual. In order to program this information into your fax modem, you should complete the setup of your fax software before sending messages.
Japan regulations
Region selection
If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection.
Redial
Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
Japan’s Telecommunications Business Law permits up to two redials on analogue telephones, but the redials must be made within a total of three minutes.
The internal modem is approved by Japan Approvals Institute for Telecommunica­tions Equipment.
A02-0604JP
Pursuant to FCC CFR 47, Part 68:
When you are ready to install or use the modem, call your local telephone company and give them the following information:
The telephone number of the line to which you will connect the modem The registration number that is located on the device
The FCC registration number of the modem will be found on either the device which is to be installed, or, if already installed, on the bottom of the computer outside of the main system label.
The Ringer Equivalence Number (REN) of the modem, which can vary. For the
REN of your modem, refer to your modem’s label.
The modem connects to the telephone line by means of a standard jack called the USOC RJ11C.
Type of service
Your modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to state tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request.
Instructions for IC CS-03 certified equipment
1 The Industry Canada label identifies certified equipment. This certification means
that the equipment meets certain telecommunications network protective, opera­tional and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connec­tions of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections them­selves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
2 The user manual of analog equipment must contain the equipment’s Ringer
Equivalence Number (REN) and an explanation notice similar to the following: The Ringer Equivalence Number (REN) of the modem, which can vary. For the
REN of your modem, refer to your modem’s label.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termina­tion on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
3 The standard connecting arrangement (telephone jack type) for this equipment is
jack type(s): USOC RJ11C. The IC registration number of the modem is shown below.
Canada: 1353A-L4AINT
Notes for Users in Australia and New Zealand
Modem warning notice for Australia
Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compli­ance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner. To verify that the country/region is correctly set, enter the command ATI which displays the currently active setting.
To set the country/region permanently to Australia, enter the following command sequence:
A T%TE=1 ATS133=1 AT&F AT&W A T%TE=0 ATZ
Failure to set the modem to the Australia country/region setting as shown above will result in the modem being operated in a non-compliant manner. Consequently, there would be no permit in force for this equipment and the Telecoms Act 1991 prescribes a penalty of $12,000 for the connection of non-permitted equipment.
Notes for use of this device in New Zealand
The grant of a Telepermit for a device in no way indicates Telecom acceptance
of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.
In addition to satisfactory line conditions a modem can only work properly if:
a/ it is compatible with the modem at the other end of the call and b/ the application using the modem is compatible with the application at the
other end of the call - e.g., accessing the Internet requires suitable software in addition to a modem.
This equipment shall not be used in any manner which could constitute a
nuisance to other Telecom customers.
Some parameters required for compliance with Telecom’s PTC Specifications
are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications:
a/ There shall be no more than 10 call attempts to the same number within
any 30 minute period for any single manual call initiation, and
b/ The equipment shall go on-hook for a period of not less than 30 seconds
between the end of one attempt and the beginning of the next.
c/ Automatic calls to different numbers shall be not less than 5 seconds
apart.
Immediately disconnect this equipment should it become physically damaged,
and arrange for its disposal or repair.
The correct settings for use with this modem in New Zealand are as follows:
ATB0 (CCITT operation) AT&G2 (1800 Hz guard tone) AT&P1 (Decadic dialing make-break ratio =33%/67%) ATS0=0 (not auto answer) ATS6=4 (Blind dial delay) ATS7=less than 90 (Time to wait to carrier after dialing) ATS10=less than 150 (loss of carrier to hangup delay, factory default of 15
recommended)
ATS11=90 (DTMF dialing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)
When used in the Auto Answer mode, the S0 register must be set with a value
of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the
modem answers. This confirms that the call has been successfully switched through the network.
(b) caller identification information (which occurs between the first and
second ring cadences) is not destroyed.
The preferred method of dialing is to use DTMF tones (ATDT...) as this is
faster and more reliable than pulse (decadic) dialing. If for some reason you must use decadic dialing, your communications program must be set up to record numbers using the following translation table as this modem does not implement the New Zealand “Reverse Dialing” standard.
Number to be dialed: 0 1 2 3 4 5 6 7 8 9 Number to program into computer: 0 9 8 7 6 5 4 3 2 1 Note that where DTMF dialing is used, the numbers should be entered
normally.
The transmit level from this device is set at a fixed level and because of this
there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.
It is recommended that this equipment be disconnected from the Telecom line
during electrical storms.
When relocating the equipment, always disconnect the Telecom line connec-
tion before the power connection, and reconnect the power first.
This equipment may not be compatible with Telecom Distinctive Alert ca-
dences and services such as FaxAbility.
NOTE THAT FAULT CALL OUTS CAUSED BY ANY OF THE ABOVE CAUSES MAY INCUR A CHARGE FROM TELECOM
General conditions
As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications.
The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork. The Telepermit may not be assigned to other parties or other products without Telecom approval.
A Telepermit artwork for each device is included from which you may prepare any number of Telepermit labels subject to the general instructions on format, size and colour on the attached sheet.
The Telepermit label must be displayed on the product at all times as proof to purchasers and service personnel that the product is able to be legitimately connected to the Telecom network.
The Telepermit label may also be shown on the packaging of the product and in the sales literature, as required in PTC 100.
The charge for a Telepermit assessment is $337.50. An additional charge of $337.50 is payable where an assessment is based on reports against non-Telecom New Zealand Specifications. $112.50 is charged for each variation when submitted at the same time as the original.
An invoice for $NZ1237.50 will be sent under separate cover.
TEAC CD-ROM drive CD-224E, CD­RW/DVD-ROM drive DW-224E safety instruction
CAUTIONS: 1. The CD/DVD drive employs a laser system. To ensure
proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho­rized service location.
2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
Location of the required label
THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.
MANUFACTURED:
Manufactured by TEAC Corporation 3-7-3 Naka-cho, Musashino-shi, Tokyo, Japan
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PROD­UCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825
ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING,
NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION.
UNDGÅ UDSÆTTELSE FOR STRÅLING
VORSICHT: Dieses Gerät enthält ein Laser­System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste “autorisierte Service-Ve rtretung”. Um einen direkten Kontakt mit dem Laserstrahl zu vermeiden darf das Gerät nicht geöffnet werden.
ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
APPARATET BOR KUN ÅBNES AF FAGFOLK MED SÆRLIGT KENDSKAB TIL APPARATER MED LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her gengivne advarselsmækning, som advarer imod at foretage sådanne indgreb i apparatet, at man kan komme til at udsætte sig for laserstråling.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä.
CAUTION: USE OF CONTROLS OR ADJUST­MENTS OR PERFORMANCE OF PROCE­DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.
Toshiba DVD-ROM drive SD-C2612, CD-RW/DVD-ROM drive SD-R2412, DVD-R/-RW drive SD-R6012 safety instruction
CAUTIONS: 1. The CD/DVD drive employs a laser system. To ensure
proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho­rized service location.
2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
Location of the required label
PRODUCT IS CERTIFIED BY THE MANUF ACTURER T O COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT THE DATE OF MANUFACTURE.
MANUFACTURED:
TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME MINATO-KU, TOKYO 105-8001, JAPAN
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825
VORSICHT: Dieses Gerät enthält ein Laser­System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste “autorisierte Service-Vertretung”. Um einen direkten Kontakt mit dem Laserstrahl zu
vermeiden darf das Gerät nicht geöffnet werden.
ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING,
NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION.
UNDGÅ UDSÆTTELSE FOR STRÅLING
ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
APPARATET BOR KUN ÅBNES AF FAGFOLK MED SÆRLIGT KENDSKAB TIL APPARATER MED LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her gengivne advarselsmækning, som advarer imod at foretage sådanne indgreb i apparatet, at man kan komme til at udsætte sig for laserstråling.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä.
CAUTION: USE OF CONTROLS OR ADJUST­MENTS OR PERFORMANCE OF PROCE­DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.
HITACHI DVD-ROM drive GDR-8082 safety instruction
CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure
proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho­rized service location.
2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
Location of the required label
THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT DATE OF MANU­FACTURE.
MANUFACTURED:
Hitachi-LG Data Storage, Inc. 26-5, TORANOMON 1-CHOME, MINATO-KU, TOKYO, 105-0001 JAPAN
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825
ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING,
NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION.
UNDGÅ UDSÆTTELSE FOR STRÅLING
VORSICHT: Dieses Gerät enthält ein Laser­System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste “autorisierte Service-Ve rtretung”. Um einen direkten Kontakt mit dem Laserstrahl zu vermeiden darf das Gerät nicht geöffnet werden.
ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
APPARATET BOR KUN ÅBNES AF FAGFOLK MED SÆRLIGT KENDSKAB TIL APPARATER MED LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her gengivne advarselsmækning, som advarer imod at foretage sådanne indgreb i apparatet, at man kan komme til at udsætte sig for laserstråling.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä.
CAUTION: USE OF CONTROLS OR ADJUST­MENTS OR PERFORMANCE OF PROCE­DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.
Panasonic CD-RW /DVD-ROM drive UJDA-740/750 safety instruction
CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To
ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
Location of the required label
COMPLIES WITH FDA RADIA TION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J.
MANUFACTURED:
Manufactured by Panasonic Communications Co., Ltd. 1-62 4-Chome Minoshima, Hakata-Ku Fukuoka,Japan
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825
VORSICHT: Dieses Gerät enthält ein Laser­System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste “autorisierte Service-Ve rtretung”. Um einen direkten Kontakt mit dem Laserstrahl zu vermeiden darf das Gerät nicht geöffnet werden.
ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING,
NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION.
UNDGÅ UDSÆTTELSE FOR STRÅLING
ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
APPARATET BOR KUN ÅBNES AF FAGFOLK MED SÆRLIGT KENDSKAB TIL APPARATER MED LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her gengivne advarselsmækning, som advarer imod at foretage sådanne indgreb i apparatet, at man kan komme til at udsætte sig for laserstråling.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä.
CAUTION: USE OF CONTROLS OR ADJUST­MENTS OR PERFORMANCE OF PROCE­DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.

Table of Contents

Preface
Manual contents ............................................................................. xxxi
Conventions ................................................................................... xxxii
Abbreviations ....................................................................................xxxii
Icons ................................................................................................xxxii
Keys ...............................................................................................xxxiii
Key operation ..................................................................................xxxiii
Display ............................................................................................xxxiii
Messages ....................................................................................... xxxiii
General Precautions
Stress injury ................................................................................... xxxv
Heat injury...................................................................................... xxxv
Pressure or impact damage ......................................................... xxxv
CPU performance disclaimer ...................................................... xxxvi
PC card overheating .................................................................... xxxvi
LCD Display................................................................................... xxxvi
Chapter 1 Introduction
Equipment checklist .......................................................................... 1-1
Hardware ............................................................................................ 1-1
Software ............................................................................................. 1-1
Documentation ................................................................................... 1-2
Features ............................................................................................. 1-2
Processor........................................................................................... 1-2
Memory .............................................................................................. 1-3
Power ................................................................................................. 1-3
Disks.................................................................................................. 1-3
Display ............................................................................................... 1-5
Keyboard............................................................................................ 1-5
Pointing device ................................................................................... 1-6
Ports .................................................................................................. 1-6
Slots .................................................................................................. 1-6
Multimedia.......................................................................................... 1-6
xxiii
Communications................................................................................. 1-7
Security.............................................................................................. 1-7
Software ............................................................................................. 1-7
Special features ................................................................................. 1-7
Utilities................................................................................................ 1-9
Options ............................................................................................. 1-11
Chapter 2 The Grand Tour
Front with the display closed ........................................................... 2-1
Left side.............................................................................................. 2 -2
Right side ........................................................................................... 2-3
Back side............................................................................................ 2-4
Underside ........................................................................................... 2-6
Front with the display open.............................................................. 2-7
System indicators .............................................................................. 2-8
Keyboard indicators .......................................................................... 2-9
USB diskette drive ........................................................................... 2-10
Fixed optical media drive .............................................................. 2-11
CD-ROM drive................................................................................... 2-11
DVD-ROM drive ................................................................................ 2-11
CD-RW/DVD-ROM drive ................................................................... 2-12
DVD-R/-RW drive.............................................................................. 2-13
Universal AC adaptor ...................................................................... 2-14
Chapter 3 Getting Started
Setting up your work space.............................................................. 3-1
General conditions.............................................................................. 3-2
Placement of the computer................................................................. 3-2
Seating and posture ........................................................................... 3-3
Lighting .............................................................................................. 3-4
Work habits........................................................................................ 3-4
Connecting the universal AC adaptor.............................................. 3-5
Opening the display .......................................................................... 3-6
Turning on the power ....................................................................... 3-6
Starting up for the first time.............................................................. 3-7
Turning off the power ....................................................................... 3-7
Shut Down mode (Boot mode) ............................................................ 3-7
Hibernation mode ............................................................................... 3-8
Standby mode .................................................................................. 3-10
Restarting the computer ................................................................. 3-12
xxiv
Restoring the preinstalled software from the
Product Recovery CD-ROM....................................................... 3-12
Chapter 4 Operating Basics
Pointing devices ................................................................................ 4-1
Using the Touch Pad .......................................................................... 4-1
Using the USB diskette drive ............................................................ 4-2
Connecting 3 1/2" diskette drive ......................................................... 4-2
Disconnecting 3 1/2" diskette drive .....................................................4-3
Using optical media drives ............................................................... 4-3
Loading discs ..................................................................................... 4-4
Removing discs .................................................................................. 4-6
Writing CDs on CD-RW/DVD-ROM drive ........................................... 4- 7
Before writing or rewriting.................................................................... 4-8
When writing or rewriting ....................................................................4-8
Writing CD/DVDs on DVD-R/-RW drive ............................................. 4-9
Important message............................................................................. 4-9
Disclaimer .......................................................................................... 4-9
Read/write function chart .................................................................. 4-11
Before writing or rewriting.................................................................. 4-13
When writing or rewriting .................................................................. 4-13
Drag’n Drop CD+DVD ....................................................................... 4-14
Data Verification ............................................................................... 4-14
Media care ....................................................................................... 4-15
CD/DVDs.......................................................................................... 4-15
Diskettes.......................................................................................... 4-15
Modem.............................................................................................. 4-16
Region selection............................................................................... 4-16
Properties menu ............................................................................... 4-17
Connecting ....................................................................................... 4-18
Disconnecting................................................................................... 4-19
Wireless communications............................................................... 4-19
Wireless LAN ................................................................................... 4-19
Security............................................................................................ 4-20
Wireless communication switch ....................................................... 4-20
Wireless communication Indicator .................................................... 4-21
LAN ................................................................................................... 4-21
Connecting LAN cable ...................................................................... 4-22
Disconnecting LAN cable ................................................................. 4-22
Cleaning the computer ................................................................... 4-23
Moving the computer ...................................................................... 4-23
Heat dispersal .................................................................................. 4-24
xxv
Chapter 5 The Keyboard
Typewriter keys ................................................................................. 5-1
F1 … F12 function keys ..................................................................... 5-2
Soft keys: Fn key combinations........................................................ 5-2
Emulating keys on enhanced keyboard .............................................. 5-2
Hot keys............................................................................................. 5-4
Fn Sticky key..................................................................................... 5-7
Windows special keys ....................................................................... 5-7
Keypad overlay.................................................................................. 5-7
Turning on the overlays....................................................................... 5-7
Temporarily using normal keyboard (overlay on).................................. 5-8
Temporarily using overlay (overlay off) .................................................5-9
Temporarily changing modes .............................................................. 5-9
Generating ASCII characters ............................................................ 5-9
Chapter 6 Power and Power-Up Modes
Power conditions............................................................................... 6-1
Power indicators ............................................................................... 6- 2
Battery indicators ............................................................................... 6-2
DC IN indicator ................................................................................... 6-3
Power indicator................................................................................... 6-3
Battery types ...................................................................................... 6-3
Battery pack....................................................................................... 6-4
Real Time Clock battery ..................................................................... 6-4
Care and use of the battery pack ..................................................... 6-5
Safety precautions.............................................................................. 6-5
Charging the batteries ........................................................................ 6-8
Monitoring battery capacity .............................................................. 6-10
Maximizing battery operating time .................................................... 6-10
Retaining data with power off ............................................................ 6-11
Extending battery life........................................................................ 6-11
Replacing the battery pack............................................................. 6-12
Removing the battery pack ............................................................... 6-12
Installing the battery pack................................................................. 6-13
Starting the computer by password ............................................... 6-15
Power-up modes ............................................................................. 6-15
Windows utilities .............................................................................. 6-15
Hot keys........................................................................................... 6-15
Panel power off ............................................................................... 6-16
System Auto Off ............................................................................... 6-16
xxvi
Chapter 7 HW Setup and Passwords
HW Setup ........................................................................................... 7-1
Accessing HW Setup ......................................................................... 7-1
HW Setup window .............................................................................. 7-1
Supervisor password....................................................................... 7-10
Chapter 8 Optional Devices
PC cards ............................................................................................. 8- 2
Inserting a PC card............................................................................. 8-2
Removing a PC card ........................................................................... 8-3
Memory expansion............................................................................ 8-4
Installing memory module................................................................... 8-4
Removing memory module.................................................................. 8-6
Battery pack ....................................................................................... 8-7
Universal AC adaptor ........................................................................ 8-7
USB FDD kit........................................................................................ 8-7
External monitor................................................................................ 8-8
TV........................................................................................................ 8-8
Changing the resolution ...................................................................... 8-9
Security lock .................................................................................... 8-11
Chapter 9 Troubleshooting
Problem solving process................................................................... 9-1
Preliminary checklist .......................................................................... 9-1
Analyzing the problem ........................................................................9-2
Hardware and system checklist........................................................ 9-3
System start-up.................................................................................. 9- 3
Self test.............................................................................................. 9- 4
Power ................................................................................................. 9-4
Password ........................................................................................... 9-7
Keyboard............................................................................................ 9-7
LCD panel ........................................................................................ 9-10
Hard disk drive.................................................................................. 9-11
CD-ROM drive................................................................................... 9-11
DVD-ROM drive ................................................................................ 9-13
xxvii
CD-RW/DVD-ROM drive ................................................................... 9-14
DVD-R/-RW drive.............................................................................. 9-16
Diskette drive.................................................................................... 9-18
PC card ............................................................................................ 9-18
Pointing device ................................................................................. 9-19
USB ................................................................................................. 9-21
Memory expansion ........................................................................... 9-21
Sound system .................................................................................. 9-22
Monitor............................................................................................. 9-22
Modem ............................................................................................. 9-23
LAN.................................................................................................. 9-24
Wireless LAN ................................................................................... 9-25
Real Time Clock ............................................................................... 9-25
TOSHIBA support ............................................................................. 9-26
Before you call ................................................................................. 9-26
Where to write .................................................................................. 9-26
Appendixes
Appendix A
Specifications ................................................................................... A-1
Appendix B
Display Controller and Modes ......................................................... B-1
Appendix C
AT Commands .................................................................................. C-1
Appendix D
S-registers ......................................................................................... D-1
Appendix E
V.90.....................................................................................................E-1
Appendix F
Internal Modem Guide ......................................................................F-1
Appendix G
Wireless LAN..................................................................................... G-1
Appendix H
AC Power Cord and Connectors...................................................... H-1
xxviii
Appendix I
Parts Numbers ....................................................................................I-1
Glossary Index
xxix
xxx

Preface

Congratulations on your purchase of the Satellite A10 series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing.
This manual tells how to set up and begin using your Satellite A10 series computer. It also provides detailed information on configuring your computer, basic opera­tions and care, using optional devices and troubleshooting.
If you are a new user of computers or if you’re new to portable computing, first read over the Introduction and The Grand Tour chapters to familiarize yourself with the computer’s features, components and accessory devices. Then read Getting
Started for step-by-step instructions on setting up your computer.
If you are an experienced computer user, please continue reading the preface to learn how this manual is organized, then become acquainted with this manual by browsing through its pages. Be sure to look over the Special features section of the
Introduction, to learn about features that are uncommon or unique to the computers
and carefully read HW Setup and Passwords.

Manual contents

This manual offers important information about your computer, including solutions to the most common problems, and features and specifications. Refer to the Online manual preinstalled on your system for the details. To open the Online manual, follow the steps below:
From Desk top, click Start, point to All programs, click TOSHIBA User's Manual. The Online manual is composed of the following nine chapters, a glossary and an
index. Chapter 1, Introduction, is an overview of the computer’s features, capabilities, and
options. Chapter 2, The Grand Tour, identifies the components of the computer and briefly
explains how they function. Chapter 3, Getting Started, provides a quick overview of how to begin operating
your computer and gives tips on safety and designing your work area.
xxxi
Chapter 4, Operating Basics, includes instructions on using the following devices: Touch Pad, USB diskette drive, optical media drives, modem, wireless communica­tion features, LAN. It also provides tips on care of the computer, diskettes and CD/ DVDs.
Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys.
Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes.
Chapter 7, HW Setup and Passwords , explains how to configure the computer using the HW Setup program.It also tells how to set a password.
Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, suggests courses of action if the computer doesn’t
seem to be working properly. The Appendixes provide technical information about your computer. The Glossary defines general computer terminology and includes a list of acronyms
used in the text. The Index quickly directs you to the information contained in this manual.

Conventions

This manual uses the following formats to describe, identify, and highlight terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary.

Icons

Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on.
xxxii

Keys

The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key.

Key operation

Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
ABC When procedures require an action such as clicking an icon or entering
text, the icon’s name or the text you are to type in is represented in the type face you see to the left.

Display

ABC Names of windows or icons or text generated by the computer that
appears on its display screen is presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below.
CAUTION: Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment.
NOTE: Please read. A note is a hint or advice that helps you make best use of your equipment.
xxxiii
xxxiv

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.
Be certain to read the general precautions below and to note the cautions included in the text of the manual.

Stress injury

Carefully read the Safety Instruction Manual. It contains information on prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. Chapter 3, Getting Started, also includes information on work space design, posture and lighting that can help reduce physical stress.

Heat injury

Avoid prolonged physical contact with the bottom of the computer. If the
computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time (if you rest the computer on your lap, for example) your skin might suffer low-heat injury.
If the computer has been used for a long time, avoid direct contact with the
metal plate supporting the I/O ports. It can become hot.
The surface of the AC adaptor can become hot when in use. This condition
does not indicate a malfunction. If you need to transport the AC adaptor, disconnect it and let it cool before moving it.
Do not lay the AC adaptor on a material that is sensitive to heat. The material
could be damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to strong impact. Excessive pressure or impact can damage computer components or otherwise cause malfunctions.
xxxv

Central Processing Unit ("CPU") Performance Disclaimer

CPU Performance in your computer product may vary from specifications under the following conditions:
1. use of certain external peripheral products
2. use of battery power instead of AC power
3. use of certain multimedia games or videos with special effects
4. use of standard telephone lines or low speed network connections
5. use of complex modeling software, such as high end computer aided design applications
6. use of computer in areas with low air pressure (high altitude >1,000 meters or >3,280 feet above sea level)
7. use of computer at temperatures outside the range of 5 C to 35 C (41 F to 95 F) or >25 C (77 F) at high altitude (all temperature references are approximate).
CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shut-down. This
is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions. Read additional restrictions under "Environmental Requirements" defined in the Appendix A. Contact TOSHIBA Technical Service and Support for more information.

PC Card overheating

Some PC cards can become hot with prolonged use. Overheating of a PC Card can result in errors or instability in the PC Card operation. Also be careful when you remove a PC Card that has been used for a long time.

LCD Display

TFT color LCD is manufactured by using very high brightness technology. Some sequential pixels may not light or may light always, but this is not a failure.
xxxvi
Chapter 1
Introduction
Equipment checklist .......................................................................... 1-1
Hardware ............................................................................................ 1-1
Software ............................................................................................. 1-1
Documentation ................................................................................... 1-2
Features ............................................................................................. 1-2
Processor........................................................................................... 1-2
Memory .............................................................................................. 1-3
Power ................................................................................................. 1-3
Disks.................................................................................................. 1-3
Display ............................................................................................... 1-5
Keyboard............................................................................................ 1-5
Pointing device ................................................................................... 1-6
Ports .................................................................................................. 1-6
Slots .................................................................................................. 1-6
Multimedia.......................................................................................... 1-6
Communications................................................................................. 1-7
Security.............................................................................................. 1-7
Software ............................................................................................. 1-7
Special features ................................................................................. 1-7
Utilities................................................................................................ 1-9
Options ............................................................................................. 1-11
I
NTRODUCTION
INTRODUCTION
Chapter 1
Introduction
This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories.
CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not prein­stalled by TOSHIBA.

Equipment checklist

Carefully unpack your computer. Save the box and packing materials for future use.
Hardware
Check to make sure you have all the following items:
Satellite A10 Series Portable Personal Computer Universal AC adaptor and power cord USB diskette drive (Provided with some models) Modular cable
I
NTRODUCTION
Software
The following software is preinstalled:
Microsoft® Windows XP Home Edition/Professional
• Modem driver
Display Drivers for Windows
• TOSHIBA Utilities
Wireless LAN driver (Can be used only for Wireless LAN models)
Sound Driver for Windows
DVD Video Player
LAN Drivers
ALPS Pointing device Driver
TOSHIBA Power Saver
TOSHIBA Console
1-1
User's Manual
Online manual
Product Recovery CD-ROM
Documentation
INTRODUCTION
Satellite A10 Series Portable Personal Computer User's Manual
Microsoft Windows XP manual package
Instruction Manual for Safety & Comfort
End User License Agreement

Features

The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Comple­mentary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits:
Processor
Built-in The computer is equipped with an Intel® processor.
1-2
Mobile Intel® Celeron® processor, which incorporates a 256KB level 2 cache memory.
1.80GHz Mobile Intel® Celeron® processor 1.80 GHz
2.00GHz Mobile Intel® Celeron® processor 2.00 GHz
2.20GHz Mobile Intel® Celeron® processor 2.20 GHz
Mobile Intel® Pentium® 4 - M processor, which incorporates a 512KB level 2 cache memory.
1.80GHz Mobile Intel® Pentium® 4 processor 1.80 GHz -M
1.90GHz Mobile Intel® Pentium® 4 processor 1.90 GHz -M
2.00GHz Mobile Intel® Pentium® 4 processor 2.00 GHz -M
2.20GHz Mobile Intel® Pentium® 4 processor 2.20 GHz -M
Features
Memory
Slots 128, 256 or 512 MB memory modules can be installed in the
two memory slots for a maximum of 1 GB system memory.
Video RAM Allocated a part of System Memory dynamically. (Limit of
graphics memory is 32MB at 128MB of System Memory, Limit of Graphics memory is 64MB at more than 256MB of System Memory)
Power
Battery pack The computer is powered by one rechargeable lithium-ion
battery pack.
RTC battery The computer has an internal battery to back up the
internal Real Time Clock (RTC) and calendar.
Universal AC adaptor The universal AC adaptor provides power to the system
and recharges the batteries when they are low. It comes with a detachable power cord.
Because it is universal, it can receive a range of AC voltage from 100 to 240 volts; however, the output current varies among different models. Using the wrong model can damage your computer. See the universal AC adaptor section in Chapter 2, The Grand Tour.
I
NTRODUCTION
Disks
Hard disk drive Available in four sizes.
• 18.63 GB(20.0 billion bytes)
• 27.94 GB (30.0 billion bytes)
• 37.26 GB (40.0 billion bytes)
• 55.88 GB (60.0 billion bytes)
USB diskette drive Accommodates either 3 1/2" 1.44-megabyte or 720-kilobyte
diskettes. It connects to a USB port.
CD-ROM drive Some models are equipped with a full-size,CD-ROM drive
module that lets you run CD without using an adaptor. It reads CD-ROMs at maximum 24 speed. This drive supports the following formats.
CD-DA CD-Text
Photo CDTM(single/multi-session)
1-3
User's Manual
CD-ROM Mode 1, Mode 2
CD-ROM XA Mode 2 (Form1, Form2)
Enhanced CD (CD-EXTRA)
INTRODUCTION
DVD-ROM drive Some models are equipped with a full-size, DVD-ROM
CD-RW/DVD-ROM Some models are equipped with a full-size, CD-RW/DVD-
CD-G (Audio CD only)
Addressing Method 2
drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") CDs or 12cm(4.72") DVDs without using an adaptor. It runs DVD-ROMs at maximum 8 speed and CD­ROMs at maximum 24 speed. The drive supports the following formats:
• DVD-ROM • DVD-Video
• CD-DA • CD-Text
• Photo CD™ (single/multi-session)
• CD-ROM Mode 1, Mode 2
• CD-ROM XA Mode 2 (Form1, Form2)
• Enhanced CD (CD-EXTRA)
• CD-G (Audio CD only)
• Addressing Method 2
drive ROM drive module that lets you run CD/DVDs without
using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed and CD-RW at up to 10 speed. For reading, this drive supports the same formats as the DVD-ROM drive.
• DVD-ROM • DVD-Video
• CD-DA • CD-Text
• Photo CD™ (single/multi-session)
• CD-ROM Mode 1, Mode 2
• CD-ROM XA Mode 2 (Form1, Form2)
• Enhanced CD (CD-EXTRA)
• CD-G (Audio CD only)
• Addressing Method 2
1-4
Features
DVD-R/-RW drive Some models are equipped with a full- size DVD-R/-RW
drive module that lets you record data to rewritable CD/ DVDs as well as run either 12cm (4.72") or 8cm (3.15") CDs/12cm(4.72") DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 16 speed, CD­RW at up to 10 speed, DVD-R and DVD-RW at single speed. This drive supports the same formats as the DVD­ROM drive.
• DVD-ROM • DVD-Video
• CD-DA • CD-Text
• Photo CD™ (single/multi-session)
• CD-ROM Mode 1, Mode 2
• CD-ROM XA Mode 2 (Form1, Form2)
• Enhanced CD (CD-EXTRA)
• CD-G (Audio CD only)
• Addressing Method 2
Display
The computer’s LCD panel supports high-resolution video graphics. The screen can be set at a wide range of viewing angles for maximum comfort and readability.
Built-in 14.1" XGA TFT screen or 15.0"XGA/SXGA+TFT screen,
16 M colors, with one of the following resolutions:
• XGA, 1024 horizontal x 768 vertical pixels
• SXGA+, 1400 horizontal x 1050 vertical pixels
Graphics controller Graphics controller maximizes display performance. Refer
to Appendix B for more information.
I
NTRODUCTION
Keyboard
Built-in 85 keys or 86 keys, compatible with IBM enhanced
keyboard, embedded numeric overlay, dedicated cursor control, and keys. See Chapter 5, The Keyboard, for details.
1-5
User's Manual
Pointing device
Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable
control of the on-screen pointer.
INTRODUCTION
Ports
Parallel Some models are equipped with a parallel port for parallel
printer or other parallel device (ECP compatible).Note that some models are not equipped with this port.
External monitor 15-pin, analog VGA port supports VESA DDC2B compat-
ible functions.
Universal Serial Bus The computer has two Universal Serial Bus ports that
(USB 2.0) comply with the USB 2.0 standard, which enables data
transfer speeds 40 times faster than the USB 1.1 standard. (The ports also support USB 1.1.)
Slots
PC card The PC card slot accommodates one 5 mm Type II card.
Multimedia
Sound system Windows sound system compatible sound system
provides internal speakers as well as jacks for an external microphone and headphone.
TV out Some models are equipped with TV out port.
This jack lets you transfer video and sound data to external devices. Use the S-VIDEO cable for TV out. Data output depends on the type of device connected to the
S-VIDEO cable.Note that some models are not equipped with this port.
Headphone jack This jack outputs analog audio signals.
Microphone jack A 3.5 mm mini microphone jack enables connection of a
three-conductor mini jack for monaural microphone input.
1-6

Special features

Communications
Modem An internal modem provides capability for data and fax
communication. It supports V.90 (V.92). Refer to Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets. Both of V.90 and V.92 are supported only in USA and Canada. Only V.90 is available in other regions.
LA N The computer has built-in support for Ethernet LAN (10
megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx).
Wireless LAN Some computers in this series are equipped with a wireless
LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum / Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE802.11 Standard (Revision A or B) and Turbo Mode. Revision-A supports data transfer rate up to 54Mbit/s. Revision-B supports data transfer rate up to 11Mbit/s. Turbo Mode supports data transfer rate up to 108Mbit/s.
I
NTRODUCTION
Security
Security lock slot Connects an optional security lock to anchor the computer
to a desk or other large object.
Software
Standard Windows XP operating system and TOSHIBA Utilities
and drivers preinstalled on the hard disk.
Plug and Play When you connect an external device to the computer,
Plug and Play capability enables the system to recognize the connection and make the necessary configurations automatically.
Special features
The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use.
1-7
User's Manual
Hot keys Key combinations let you quickly modify the system
configuration directly from the keyboard without running a system configuration program.
INTRODUCTION
Display automatic This feature automatically cuts off power to the internal
power off display when there is no input from the keyboard or
pointing device for a time specified. Power is restored when any key is pressed or when there is input from a pointing device. You can specify the time in the Turn off monitor item of the Power Save Mode window in TOSHIBA Power Saver.
HDD automatic This feature automatically cuts off power to the hard disk
power off drive when it is not accessed for a time specified. Power is
restored when the hard disk is accessed. You can specify the time in the Turn off hard disks item of the Power Save Mode window in TOSHIBA Power Saver.
System automatic This feature automatically shuts down the system in
Standby/Hibernation standby mode or Hibernation mode when there is no input
or hardware access for a time specified. You can specify the time and select either System Standby or System Hibernate in the System standby and System hibernate item of the Power Save Mode window in TOSHIBA Power Saver.
Keypad overlay A ten-key pad is integrated into the keyboard. Refer to the
Keypad overlay section in Chapter 5, Keyboard, for
instructions on using the keypad overlay.
Power on password Two levels of password security, supervisor and user, are
available to prevent unauthorized access to your computer.
Instant security A hot key function blanks the screen and disables the
computer providing data security.
Intelligent A microprocessor in the computer’s intelligent power
power supply supply detects the battery’s charge and calculates the
remaining battery capacity. It also protects electronic components from abnormal conditions, such as voltage overload from a universal AC adaptor. You can monitor remaining battery capacity. Use the Battery remaining item of the Power Save Modes window in TOSHIBA Power Saver.
1-8

Utilities

Battery save mode This feature lets you save battery power. You can specify
the Power Save Mode in the Running on batteries item of the Power Save Modes window in TOSHIBA Power Saver.
Panel power off/on This feature turns power to the computer off when the
display panel is closed and turns it back on when the panel is opened. You can specify the setting in the When I close the lid item of the System Power Mode window in TOSHIBA Power Saver.
Low battery When battery power is exhausted to the point that
automatic hibernation computer operation cannot be continued, the system
automatically enters Hibernation and shuts down. You can specify the setting in the Battery Alarm item of the Alarm window in TOSHIBA Power Saver.
Heat dispersal The CPU has an internal temperature sensor that automati-
cally activates cooling procedures. Refer to the Heat
dispersal section in Chapter 4, Operating Basics, for
details on setting the options for cooling methods.
Hibernation This feature lets you turn off the power without exiting
from your software. The contents of main memory is saved to the hard disk, when you turn on the power again, you can continue working right where you left off. Refer to the
Turning off the power section in Chapter 3, Getting
Started, for details.
Standby If you have to interrupt your work, you can turn off the
power without exiting from your software. Data is main­tained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off.
I
NTRODUCTION
Utilities
This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files.
TOSHIBA Power Saver To access this power savings management program, open
the Control Panel and select the TOSHIBA Power Saver icon.
1-9
User's Manual
HW Setup This program lets you customize your hardware settings
according to the way you work with your computer and the peripherals you use. To start the utility, click the Windows Start button and click Control Panel. In the
INTRODUCTION
TOSHIBA Console TOSHIBA Console is a graphical user interface that
Fn-esse This Windows program lets you define your own “short-
DVD Video Player The DVD Video Player is used to play DVD-Video. It has
ConfigFree ConfigFree is a suite of utilities to allow easy control of
Control Panel, select the TOSHIBA HW Setup icon.
provides access to help and services.
cut” keys to quickly launch applications and speed your work in Windows. To start the utility, click the Windows Start button, point to All Programs, point to TOSHIBA Utilities and click Fn-esse.
an on-screen interface and functions. Click Start, point to All Programs, point to InterVideo WinDVD 4, then click InterVideo WinDVD 4.
communication device and network connections. ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks. You can boot ConfigFree from the menu bar as follows. [Start] - [All Programs] - [TOSHIBA ConfigFree] ­[ConfigFree]
Drag’n Drop CD+DVD This easy-to-use software lets you record CDs with just a
few mouse clicks. You can create CDs in several formats including audio CDs that can be played on a standard stereo CD player and data CDs to store the files and folders on your hard drive. This software can be used on the model with CD-RW/DVD-ROM drive or DVD-R/-RW drive.
TOSHIBA Touch Pad Pressing Fn + F9 in a windows environment enables or
On/Off Utility disables the Touch Pad function.When you press these
hot keys, the current setting will change and be displayed as an icon.
1-10

Options

Options
You can add a number of options to make your computer even more powerful and convenient to use. The following options are available:
Memory expansion A 128, 256 or 512 MB memory module (PC2100, DDR) can
easily be installed in the computer.
Battery pack An additional battery pack can be purchased from your
TOSHIBA dealer. Use it as a spare or replacement.
Universal AC adaptor If you use your computer at more than one site frequently,
it may be convenient to purchase an additional universal AC adaptor for each site so you will not have to carry the adaptor with you.
Battery charger The battery charger lets you charge extra batteries outside
the computer.
USB FDD Kit A 3 1/2" diskette drive accommodates 1.44-megabyte or
720-kilobyte diskette. It connects to a USB port. (You cannot format 720-kilobyte diskettes on Windows XP, but you can use previously formatted disks.)
Wireless LAN Kit This option enables wireless LAN functions in computers
that do not have wireless preinstalled. It is installed by dealers only. Two types of Wireless LAN kit are prepared: Wireless LAN Kit for IEEE 802.11 Standard (Revision B) and Wireless LAN Kit for IEEE 802.11 Standard (Revision A and B)
I
NTRODUCTION
1-11
User's Manual
INTRODUCTION
1-12
Chapter 2
The Grand Tour
Front with the display closed ........................................................... 2-1
Left side.............................................................................................. 2 -2
Right side ........................................................................................... 2-3
Back side............................................................................................ 2-4
Underside ........................................................................................... 2-6
Front with the display open.............................................................. 2-7
System indicators .............................................................................. 2-8
Keyboard indicators .......................................................................... 2-9
USB diskette drive ........................................................................... 2-10
Fixed optical media drive .............................................................. 2-11
CD-ROM drive................................................................................... 2-11
DVD-ROM drive ................................................................................ 2-11
CD-RW/DVD-ROM drive ................................................................... 2-12
DVD-R/-RW drive.............................................................................. 2-13
Universal AC adaptor ...................................................................... 2-14
T
HE
G
RAND
T
OUR
THE GRAND TOUR
Chapter 2
The Grand Tour
This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer.
T
HE
G
RAND

Front with the display closed

Figure 2-1 shows the computer’s front with its display panel in the closed position.
VOLUME CONTROL SYSTEM INDICATORS
WIRELESS COMMUNICATION
INDICATOR
Figure 2-1 Front of the computer with display closed
Volume control Use this dial to adjust the volume of the stereo speakers or
the stereo headphones.
System LEDs let you monitor the status of various computer
indicators functions. Details are given in the Indicators section.
WIRELESS COMMUNICATION
SWITCH
DISPLAY LATCH
T
OUR
Display latch This latch secures the LCD panel in its closed position.
Slide the latch to open the display.
2-1
User's Manual
Wireless Slide this switch toward the left of the computer to turn
communication off Wireless LAN function. Slide it toward the right of
switch the computer to turn on the functions (Wireless LAN
model or Wireless LAN ready model only).
CAUTION: Set the switch to off in airplanes and hospitals. Check the wireless communication indicator. It will stop glowing when the wireless communication function is off.
Wireless This indicator glows orange when Wireless LAN function
communication is on (Wireless LAN model or Wireless LAN ready model
Indicator only).
THE GRAND TOUR

Left side

Figure 2-2 shows the computer’s left side.
COOLING VENTS MICROPHONE JACK HEADPHONE JACK
PC CARD SLOT
Figure 2-2 The left side of the computer
Cooling vents These vents provide an outlet for air pulled through the
computer by the fan.
CAUTION: Be careful not to block the cooling vents. Also be careful to keep foreign objects out of them. A pin or similar object can damage the computer’s circuitry.
Microphone jack A 3.5 mm mini microphone jack enables connection of a
three-conductor mini jack for monaural microphone input.
2-2

Right side

Headphone jack This jack lets you connect digital speakers or a stereo
headphone (16 ohm minimum). When you connect a digital speaker or headphones, the internal speaker is automati­cally disabled.
PC card slot A PC card slot can accommodate one 5 mm Type II card.
CB
CAUTION: Keep foreign objects out of the PC card slot. A pin or similar object can damage the computer’s circuitry.
You can install any industry standard PC card such as a SCSI adaptor, Ethernet adaptor or flash memory card.
Right side
Figure 2-3 shows the computer’s right side.
FIXED OPTICAL MEDIA DRIVE
T
HE
G
RAND
T
OUR
MODEM JACK
Figure 2-3 The right side of the computer
Fixed Optical See Chapter 4, Operating Basics, for information on using
Media Drive the drive and caring for CDs and DVDs.
CD-ROM drive Some models are equipped with a full-size CD-ROM drive
module that lets you run CD without using an adaptor.
DVD-ROM drive Some models are equipped with a full-size DVD-ROM drive
module that lets you run DVD-ROM without using an adaptor.
CD-RW/ Some models are equipped with a full-size CD-RW/DVD-
DVD-ROM drive ROM drive module that lets you run CD/DVDs without
using an adaptor.You can also write CDs.
2-3
User's Manual
DVD-R/-RW drive Some models are equipped with a full-size DVD-R/-RW
drive module that lets you record data to rewritable CD/ DVDs as well as run CD/DVDs without using an adaptor.You can also write CD/DVDs.
Modem jack In areas where an internal modem is installed as standard
equipment, there is a modem jack that lets you use a modular cable to connect the modem directly to a tele­phone line.
CAUTIONS: 1. In case of a lightning storm, unplug the modem cable
from the telephone jack.
THE GRAND TOUR
2. Do not connect the modem to a digital telephone line. A digital line will damage the modem.

Back side

Figure 2-4 shows the computer’s back panel.
LAN
JACK
LAN ACTIVE
INDICATOR
(ORANGE)
PORTS
SECURITY LOCK
DC IN 15V USB
* Some models are not equipped with a Parallel Port or a TV Out Port.
Figure 2-4 The back side of the computer
Security lock A security cable attaches to this slot. The optional
security cable anchors your computer to a desk or other large object to deter theft.
LAN active This indicator glows orange when data is being exchanged
indicator (orange) between the computer and the LAN.
LINK INDICATOR (GREEN)
TV OUT
*
PORT
PARALLEL
*
PORT
EXTERNAL MONITOR PORT
2-4
Back side
Link indicator This indicator glows green when the computer is connect-
(green) ed to a LAN and the LAN is functioning properly.
Parallel port Some models are equipped with a Centronics-compatible,
25-pin parallel port that is used to connect a parallel printer or other parallel device.This port supports Extended Capabilities Port (ECP) standard.
External monitor This 15-pin port lets you connect an external video
port display.
T
HE
G
RAND
TV out port Some models are equipped with a TV out port.Plug an S-
Video cable into this jack for TV out. Use the TV button to turn on and off the TV display.
Universal Two Universal Serial Bus ports are on the back side.
Serial Bus The port comply with the USB 2.0 standard, which
(USB 2.0) ports enables data transfer speed 40 times faster than the USB 1.1
standard. (The ports also support USB 1.1.)
CAUTION: Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry. NOTE: Operation of all functions of all USB devices has not been confirmed. Some functions might not execute properly.
LAN jack
Ether
This jack lets you connect to a LAN. The adaptor has built­in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). The LAN has two indicators. See Chapter 4, Operating Basics, for details.
CAUTIONS: 1. Do not connect cables other than LAN, otherwise it
causes a failure or damage.
2. Do not connect equipment which supplies electric
power,otherwise it causes a failure or damage.
T
OUR
DC IN 15V The universal AC adaptor connects to this socket. Use
only the model of universal AC adaptor that comes with
DC IN 15V
the computer. Using the wrong adaptor can damage your computer.
2-5
User's Manual

Underside

Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer.
BATTERY RELEASE LATCH
BATTERY SAFETY LOCK
BATTERY PACK
THE GRAND TOUR
MEMORY MODULE COVER
Figure 2-5 The underside of the computer
Battery release Slide this latch to release the battery pack for removal.
latch For detailed information on removing the battery
packs,refer to Chapter 6, Power and Power-Up Modes.
Battery safety lock Switch this safety lock to make the battery release latch
slide freely or locked. For detailed information, refer to Chapter 6, Power and Power-Up Modes.
Battery pack The battery pack powers the computer when the universal
AC adaptor is not connected. For detailed information on the battery pack, refer to Chapter 6, Power and Power-Up
Modes.
Memory module This cover protects two memory module sockets
cover One or two modules are preinstalled. Refer to the memory
expansion section in Chapter 8, Optional Devices.
2-6

Front with the display open

Front with the display open
Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the display to the right of the computer and lift up. Position the display at a comfortable viewing angle.
DISPLAY HINGE
STEREO SPEAKER (LEFT)
POWER BUTTON
TOUCH PAD
DISPLAY SCREEN
STEREO SPEAKER (RIGHT)
TOUCH PAD CONTROL BUTTONS
Figure 2-6 The front with the display open
T
HE
G
RAND
T
OUR
Display hinge The display hinge holds the display screen at easy-to-
view angles.
Display screen The LCD displays high-contrast text and graphics. The
computer’s LCD consists of up to 1024 x 768 pixels or 1400 x 1050 pixels. Refer to Appendix B.
When the computer operates on the universal AC adaptor the display screen’s image will be somewhat brighter than when it operates on battery power. The lower brightness level is intended to save battery power.
2-7
User's Manual
Stereo speakers The speakers emit sound generated by your software as
well as audio alarms, such as low battery condition, generated by the system.
Power button Press the power button to turn the computer’s power on
and off.
Touch Pad A Touch Pad located slightly in the left from the center of
the palm rest is used to control the on-screen pointer. Refer to the Using the Touch Pad section in Chapter 4, Operating Basics.
Touch Pad Control buttons close to the Touch Pad let you select
THE GRAND TOUR
control buttons menu items or manipulate text and graphics designated by
the on-screen pointer.

System indicators

DC IN 15V POWER BATTERY BUILT-IN CD-ROM DRIVE
HDD
Figure 2-7 System indicators
DC IN 15V The DC IN indicator glows green when DC power is
supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunc­tions, this indicator flashes orange.
Power The Power indicator glows green when the computer is
on. If you select Standby from Shut Down Windows, this indicator flashes orange (one second on, two seconds off) while the computer shuts down.
Battery The Battery indicator shows the condition of the
battery’s charge: Green indicates full charge, orange indicates battery charging and flashing orange indicates a low battery charge. Refer to Chapter 6, Power and Power-
Up Modes.
Built-in HDD The Built-in HDD indicator glows green when the
computer is accessing the hard disk.
2-8

keyboard indicators

CD-ROM This indicator glows green when the computer is
drive accessing a diskette in the diskette drive or a disk in the
CD-ROM,DVD-ROM, DVD-R/-RW or CD-RW/DVD-ROM drive.
Keyboard indicators
The figures below show the positions of the keypad overlay indicators and the CapsLock indicator.
When the F10 key indicator glows the keypad overlay lets you control the cursor. When the F11 key indicator glows the keypad overlay lets you enter numbers.
ARROW MODE
INDICATOR
Figure 2-8 Keypad overlay indicators
When the CapsLock indicator glows the keyboard is in all-caps mode.
NUMERIC MODE
INDICATOR
T
HE
G
RAND
T
OUR
CAPSLOCK INDICATOR
Figure 2-9 CapsLock indicator
Caps Lock This indicator glows green when the alphabet keys are
locked in uppercase.
2-9
User's Manual
Arrow mode When the Arrow mode indicator lights green, you can
use the keypad overlay (gray labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard.
Numeric mode You can use the keypad overlay (gray labeled keys) for
numeric input when the Numeric mode indicator lights green. Refer to the Keypad overlay section in Chapter 5, The Keyboard.

USB diskette drive

A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes. It
THE GRAND TOUR
connects to the USB port.
DISK-IN-USE INDICATOR
DISKETTE SLOT
Figure 2-10 USB diskette drive
Disk-In-Use This indicator lights when the diskette is being accessed.
Indicator
Diskette slot Insert a diskette in this slot.
Eject button When a diskette is fully seated in the drive, the eject
button pops out. To remove a diskette, push in the eject button and the diskette pops out partially for removal.
CAUTION: Check the Disk-In-Use indicator when you use the diskette drive. Do not press the eject button or turn off the computer while the light is glowing. Doing so could destroy data and damage the diskette or the drive.
2-10
EJECT BUTTON

Fixed optical media drive

NOTES: 1. The external diskette drive should be placed on a flat,
horizontal surface when in use. Do not set the drive on an incline greater than 20o while it is operating.
2. Do not set anything on top of the diskette drive.
Fixed optical media drive
CD-ROM drive
Some models are equipped with a full-size,CD-ROM drive. ROM drive module that lets you run CD without using an adaptor. It reads CD-ROMs at maximum 24 speed.
This drive supports the following formats.
• CD-DA • CD-Text
• Photo CDTM(single/multi-session)
• CD-ROM Mode 1, Mode 2
• CD-ROM XA Mode 2 (Form1, Form2)
• Enhanced CD (CD-EXTRA)
• CD-G (Audio CD only)
• Addressing Method 2
DVD-ROM drive
Some models are equipped with a full-size, DVD-ROM drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") CDs or 12cm(4.72") DVDs without using an adaptor. It runs DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. The drive supports the following formats:
• DVD-ROM • DVD-Video
• CD-DA • CD-Text
• Photo CDTM (single/multi-session)
• CD-ROM Mode 1, Mode 2
• CD-ROM XA Mode 2 (Form1, Form2)
• Enhanced CD (CD-EXTRA)
• CD-G (Audio CD only)
• Addressing Method 2
T
HE
G
RAND
T
OUR
2-11
User's Manual
DVD-ROM drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD media, make sure it matches your drive, otherwise it will not play properly.
Code Region
1. Canada, United States
2. Japan, Europe, South Africa, Middle East
3. Southeast Asia, East Asia
4. Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean
5. Russia, Indian Subcontinent, Africa, North Korea, Mongolia
THE GRAND TOUR
6. China
CD-RW/DVD-ROM drive
Some models are equipped with a full-size, CD-RW/DVD -ROM drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed and CD-RW at up to 10 speed. For reading, this drive supports the same formats as the DVD-ROM drive.
• DVD-ROM • DVD-Video
• CD-DA • CD-Text
• Photo CDTM (single/multi-session)
• CD-ROM Mode 1, Mode 2
• CD-ROM XA Mode 2 (Form1, Form2)
• Enhanced CD (CD-EXTRA)
• CD-G (Audio CD only)
• Addressing Method 2
CD-RW/DVD-ROM drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD media, make sure it matches your drive, otherwise it will not play properly.
2-12
Fixed optical media drive
Code Region
1. Canada, United States
2. Japan, Europe, South Africa, Middle East
3. Southeast Asia, East Asia
4. Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean
5. Russia, Indian Subcontinent, Africa, North Korea, Mongolia
6. China
DVD-R/-RW drive
Some models are equipped with a full- size DVD-R/-RW drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15")
CDs/12cm(4.72") DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 16 speed, CD­RW at up to 10 speed, DVD-R and DVD-RW at single speed. This drive supports the same formats as the DVD-ROM drive.
• DVD-ROM • DVD-Video
• CD-DA • CD-Text
• Photo CD TM(single/multi-session)
• CD-ROM Mode 1, Mode 2
• CD-ROM XA Mode 2 (Form1, Form2)
• Enhanced CD (CD-EXTRA)
• CD-G (Audio CD only)
• Addressing Method 2
T
HE
G
RAND
T
OUR
DVD-R/-RW drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD media, make sure it matches your drive, otherwise it will not play properly.
Code Region
1. Canada, United States
2. Japan, Europe, South Africa, Middle East
3. Southeast Asia, East Asia
2-13
User's Manual
4. Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean
5. Russia, Indian Subcontinent, Africa, North Korea, Mongolia
6. China

Universal AC adaptor

The universal AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region.
To recharge the battery, simply connect the universal AC adaptor to a power source
THE GRAND TOUR
and the computer. See Chapter 6, Power and Power-Up Modes for details.
Figure 2-11 The universal AC adaptor
CAUTION: Use only the universal AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case.
2-14
Chapter 3
Getting Started
Setting up your work space.............................................................. 3-1
General conditions.............................................................................. 3-2
Placement of the computer................................................................. 3-2
Seating and posture ........................................................................... 3-3
Lighting .............................................................................................. 3-4
Work habits........................................................................................ 3-4
Connecting the universal AC adaptor.............................................. 3-5
Opening the display .......................................................................... 3-6
Turning on the power ....................................................................... 3-6
Starting up for the first time.............................................................. 3-7
Turning off the power ....................................................................... 3-7
Shut Down mode (Boot mode) ............................................................ 3-7
Hibernation mode ............................................................................... 3-8
Standby mode .................................................................................. 3-10
Restarting the computer ................................................................. 3-12
Restoring the preinstalled software from the
Product Recovery CD-ROM....................................................... 3-12
G
ETTING
S
TARTED
GETTING STARTED
Chapter 3
Getting Started
This chapter provides basic information to get you started using your computer. It covers the following topics:
Setting up your work space — for your health and safety
NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Connecting the universal AC adaptor Opening the display Turning on the power Starting up for the first time Turning off the power Restarting the computer Restoring the preinstalled software from the Product Recovery CD-ROM
G
ETTING
S
TARTED
NOTE: All users should be sure to read the section Starting up for the first time.

Setting up your work space

Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation. This section discusses the following topics:
General conditions Placement of the computer Seating and posture Lighting Work habits
3-1
User's Manual
General conditions
In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment.
Make sure there is adequate space around the computer for proper ventilation. Make sure the AC power cord connects to an outlet that is close to the
computer and easily accessible.
The temperature should be 5 C to 35 C (41 F to 95 F) and the relative humidity
should be 20 to 80 percent.
Avoid areas where rapid or extreme changes in temperature or humidity may
occur.
Keep the computer free of dust, moisture, and exposure to direct sunlight. Keep the computer away from heat sources, such as electric heaters. Do not use the computer near liquids or corrosive chemicals. Do not place the computer near objects that create strong magnetic fields (e.g.,
stereo speakers).
Some computers in the computer, including data storage media, can be
damaged by magnets. Do not place the computer near magnetic objects or
GETTING STARTED
bring magnetic objects close to the computer. Be careful of objects, such as stereo speakers, that produce strong magnetic fields during operation. Also, be careful with metal objects, such as bracelets, which can be inadvertently magnetized.
Do not operate the computer in close proximity to a mobile phone. Leave ample ventilation room for the fan. Do not block the vents.
Placement of the computer
Position the computer and peripheral devices to provide comfort and safety.
Set the computer on a flat surface at a comfortable height and distance. The
display should be no higher than eye level to avoid eye strain.
Place the computer so that it is directly in front of you when you work and
make sure you have adequate space to easily operate other devices.
Allow adequate space behind the computer to let you freely adjust the display.
The display should be angled to reduce glare and maximize visibility.
If you use a paper holder, set it at about the same height and distance as the
computer.
3-2
Setting up your work space
Seating and posture
The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1.
BELOW EYE LEVEL
G
ETTING
FOOT REST
Figure 3-1 Posture and positioning of the computer
Place your chair so that the keyboard is at or slightly below the level of your
elbow. You should be able to type comfortably with your shoulders relaxed.
Your knees should be slightly higher than your hips. If necessary, use a foot
rest to raise the level of your knees to ease pressure on the back of your thighs.
Adjust the back of your chair so it supports the lower curve of your spine. Sit straight so that your knees, hips and elbows form approximately 90 degree
angles when you work. Do not slump forward or lean back too far.
90O ANGLES
S
TARTED
3-3
User's Manual
Lighting
Proper lighting can improve legibility of the display and reduce eye strain.
Position the computer so that sunlight or bright indoor lighting does not reflect
off the screen. Use tinted windows, shades or other screen to eliminate sun glare.
Avoid placing the computer in front of bright light that could shine directly in
your eyes.
If possible, use soft, indirect lighting in your computer work area. Use a lamp to
illuminate your documents or desk, but be sure to position the lamp so that it does not reflect off the display or shine in your eyes.
Work habits
A key to avoiding discomfort or injury from repetitive strain is to vary your activi­ties. If possible, schedule a variety of tasks into your work day. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency.
Sit in a relaxed posture. Good positioning of your chair and equipment as
GETTING STARTED
described earlier can reduce tension in your shoulders or neck and ease back strain.
Vary your posture frequently. Occasionally stand up and stretch or exercise briefly. Exercise and stretch your wrists and hands a number of times during the day. Frequently, look away from the computer and focus your eyes on a distant
object for several seconds, for example 30 seconds every 15 minutes.
Take frequent short breaks instead of one or two long breaks, for example, two
or three minutes every half hour.
Have your eyes examined regularly and visit a doctor promptly, if you suspect
you might be suffering from a repetitive strain injury.
A number of books are available on ergonomics and repetitive strain injury or repetitive stress syndrome. For more information on these topics or for pointers on exercises for such stress points as hands and wrists, please check with your library or book vendor. Also refer to the computer’s Instruction Manual for Safety &
Comfort.
3-4

Connecting the universal AC adaptor

Connecting the universal AC adaptor
Attach the universal AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power.
The universal AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the universal AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
CAUTION: Use only the AC adaptor that came with the computer or an equivalent optional adaptor.Use of the wrong adaptor could damage your computer.TOSHIBA assumes no liability for any damage in such case.
1. Connect the power cord to the universal AC adaptor.
Figure 3-2 Connecting the power cord to the universal AC adaptor
2. Connect the universal AC adaptor’s DC output plug to the DC IN input port
on the back of the computer.
Figure 3-3 Connecting the adaptor to the computer
G
ETTING
S
TARTED
3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators
on the front of the computer should glow.
3-5
User's Manual

Opening the display

The display panel can be rotated in a wide range of angles for optimal viewing.
1. Slide the display latch on the front of the computer to the right.
2. Lift the panel up and adjust it to the best viewing angle for you.
CAUTION: Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.
DISPLAY LATCH
GETTING STARTED
Figure 3-4 Opening the display

Turning on the power

This section describes how to turn on the power.
NOTE: After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting
up for the first time in this chapter.
1. Open the display.
3-6

Starting up for the first time

2. Press and hold the computer’s power button for two or three seconds.
Figure 3-5 Turning on the power
Starting up for the first time
G
ETTING
When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen.
Be sure to read the Windows End User License Agreement display carefully.
NOTE: Be sure to read the License Agreement carefully.

Turning off the power

The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode.
Shut Down mode (Boot mode)
When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen.
1. If you have entered data, save it to the hard disk or to a diskette.
2. Make sure all disk activity has stopped, then remove the CD/DVD-ROM or diskette.
CAUTION: Make sure the Built-in HDD and CD-ROM drive indicators are off. If you turn off the power while a disk is being accessed, you can lose data or damage the disk.
S
TARTED
3-7
User's Manual
3. Click start then click Turn Off Computer. From the Turn Off Computer menu select Turn Off.
4. Turn off the power to any peripheral devices.
CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.
Hibernation mode
The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored. The hibernation feature does not save the status of peripheral devices.
CAUTIONS: 1. Save your data. While entering hibernation mode, the
computer saves the contents of memory to the HDD. However, for safety sake, it is best to save your data manually.
2. Data will be lost if you remove the battery or discon­nect the universal AC adaptor before the save is completed. Wait for the Built-in HDD and CD-ROM
GETTING STARTED
drive indicators to go out.
3. Do not install or remove a memory module while the computer is in hibernation mode. Data will be lost.
Benefits of hibernation
The hibernation feature provides the following benefits:
Saves data to the hard disk when the computer automatically shuts down
because of a low battery.
NOTE: For the computer to shut down in hibernation mode, the hiberna­tion feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby will be lost.
You can return to your previous working environment immediately when you
turn on the computer.
Saves power by shutting down the system when the computer receives no
input or hardware access for the duration set by the System hibernate feature.
You can use the panel power off feature.
3-8
Turning off the power
Starting Hibernation
NOTE: You can also enable Hibernation by pressing Fn + F4. See Chapter 5, Keyboard, for details.
To enter Hibernation mode, follow the steps below.
1. Click start .
2. Select Turn Off Computer.
3. Open the Turn Off Computer dialog box. Hibernate is not displayed.
4. Press the Shift key. The Standby item will change to Hibernate.
5. Select the Hibernate.
Automatic Hibernation
The computer will enter Hibernate mode automatically when you press the power button or close the lid. First, however, make the appropriate settings according to the steps below.
1. Open the Control Panel.
2. In Windows XP, open Performance and Maintenance and open TOSHIBA Power Saver.
3. Select the Hibernate window, select the Enable Hibernate support check box and click the Apply button.
4. Select the Power Save Modes window.
5. Double-click Power Mode (Full Power, Normal, etc.) and open the System Power Mode window.
6. Enable the desired Hibernation settings for When I press the power button and When I close the lid.
7. Click the OK button.
Data save in hibernation mode
When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the Disk indicator will light.
After you turn off the computer and memory is saved to the hard disk, turn off the power to any peripheral devices.
G
ETTING
S
TARTED
3-9
User's Manual
CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.
Standby mode
If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off.
NOTE: When the AC adaptor is used, the computer goes into Standby mode depending on the setting of the TOSHIBA Power Saver feature.
• To restore operation, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW setup.
• If a network application is active when the computer automatically enters Standby, it might not be restored when the computer wakes up from standby. To prevent the computer from automatically entering standby mode, disable Standby in TOSHIBA Power Saver. Open the Standby setting. That action, however, will nullify the computer's Energy Star compliance.
GETTING STARTED
CAUTIONS: 1. Before entering Standby mode, be sure to save your data.
2. Do not install or remove a memory module while the computer is in standby mode. The computer or the module could be damaged.
3. Do not remove the battery pack while the computer is in standby mode (unless the computer is connected to an AC power source). Data in memory will be lost.
4. If you carry the computer on board an aircraft or into a hospital, be sure to shut down the computer in hiberna­tion mode or in shutdown mode to avoid radio signal interference.
Benefits of standby
The standby feature provides the following benefits:
Restores the previous working environment more rapidly than does hiberna-
tion.
3-10
Turning off the power
Saves power by shutting down the system when the computer receives no
input or hardware access for the duration set by the System Standby feature.
You can use the panel power off feature.
Executing standby
NOTE: You can also enable Standby by pressing Fn + F3. See Chapter 5, Keyboard, for details.
You can enter standby mode in one of three ways:
1. Click start, click Turn Off Computer and click Standby.
2. Close the display panel. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility described in the Control Panel.
Open Performance and Maintenance and open TOSHIBA Power Saver.
3. Press the power button. This feature must be enabled. Refer to the System
Power Mode item in Power Saver Utility described in the Control Panel.
Open Performance and Maintenance and open TOSHIBA Power Saver.
When you turn the power back on, you can continue where you left when you shut down the computer.
G
ETTING
S
TARTED
NOTES: 1. When the computer is shut down in standby mode, the
power indicator flashes orange.
2. If you are operating the computer on battery power, you can lengthen the operating time by shutting down in hibernation mode. Standby mode consumes more power.
Standby limitations
Standby will not function under the following conditions:
Power is turned back on immediately after shutting down. Memory circuits are exposed to static electricity or electrical noise.
3-11
User's Manual

Restarting the computer

Certain conditions require that you reset the system. For example, if:
You change certain computer settings. An error occurs and the computer does not respond to your keyboard
commands.
There are three ways to reset the computer system:
1. Click start then click Turn Off Computer. From the Turn Off Com- puter menu select Restart.
2. Press Ctrl + Alt + Del to display the Windows Task Manager, then select Shutdown and Restart.
3. Select Restart from the Turn Off Computer window in the start menu.
4. Press the power button and hold it down for five seconds. Wait 10 to 15 seconds, then turn the power on again by pressing the power button.
Restoring the preinstalled software
GETTING STARTED
from the Product Recovery CD-ROM
If preinstalled files are damaged, use the Product Recovery CD-ROM to restore them. To restore the operating system and all preinstalled software, follow the steps below.
CAUTION: When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.
1. Load the Product Recovery CD-ROM in the fixed optical media drive and turn off the computer’s power.
2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key.
3. Use the left or right cursor key to select the CD-ROM icon in the display menu. For details, refer to the Boot priority section in Chapter 7, HW Setup.
4. Follow the on-screen instructions.
3-12
Chapter 4
Operating Basics
Pointing devices ................................................................................ 4-1
Using the Touch Pad .......................................................................... 4-1
Using the USB diskette drive ............................................................ 4-2
Connecting 3 1/2" diskette drive ......................................................... 4-2
Disconnecting 3 1/2" diskette drive .....................................................4-3
Using optical media drives ............................................................... 4-3
Loading discs ..................................................................................... 4-4
Removing discs .................................................................................. 4-6
Writing CDs on CD-RW/DVD-ROM drive ........................................... 4- 7
Before writing or rewriting.................................................................... 4-8
When writing or rewriting ....................................................................4-8
Writing CD/DVDs on DVD-R/-RW drive ............................................. 4-9
Important message............................................................................. 4-9
Disclaimer .......................................................................................... 4-9
Read/write function chart .................................................................. 4-11
Before writing or rewriting.................................................................. 4-13
When writing or rewriting .................................................................. 4-13
Drag’n Drop CD+DVD ....................................................................... 4-14
Data Verification ............................................................................... 4-14
Media care ....................................................................................... 4-15
CD/DVDs.......................................................................................... 4-15
Diskettes.......................................................................................... 4-15
Modem.............................................................................................. 4-16
Region selection............................................................................... 4-16
Properties menu ............................................................................... 4-17
Connecting ....................................................................................... 4-18
Disconnecting................................................................................... 4-19
Wireless communications............................................................... 4-19
Wireless LAN ................................................................................... 4-19
Security............................................................................................ 4-20
Wireless communication switch ....................................................... 4-20
Wireless communication Indicator .................................................... 4-21
LAN ................................................................................................... 4-21
Connecting LAN cable ...................................................................... 4-22
Disconnecting LAN cable ................................................................. 4-22
Cleaning the computer ................................................................... 4-23
O
PERATING
B
ASICS
Moving the computer ...................................................................... 4-23
Heat dispersal .................................................................................. 4-24
OPERATING BASICS
Chapter 4
Operating Basics
This chapter gives information on basic operations including using the pointing devices, USB diskette drive, optical media drives, the microphone, the internal modem, wireless communication, and LAN. It also provides tips on caring for your computer, diskettes and CD/DVDs.

Pointing devices

The computer is equipped with a Touch Pad as a pointing device.
Using the Touch Pad
To use the Touch Pad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go.
O
PERATING
TOUCH PAD
CONTROL BUTTONS
TOUCH PAD
Figure 4-1 Touch Pad and Touch Pad control buttons
Two buttons below the keyboard are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics desig­nated by the pointer. Press the right button to display a menu or other function depending on the software you are using.
NOTE: You can also tap the Touch Pad to perform functions similar to those of the left button.
Click: Tap the Touch Pad once
B
ASICS
4-1
User's Manual
Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your
finger on the Touch Pad after the second tap and move the material.

Using the USB diskette drive

A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44­megabyte or 720-kilobyte diskettes. Refer to Chapter 2, Grand Tour, for more information.
Connecting 3 1/2" diskette drive
To connect the drive, plug the diskette drive connector into a USB port. Refer to Figure 4-2.
CAUTION: Make sure the connector is back side up and properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins.
OPERATING BASICS
Figure 4-2 Connecting the USB diskette drive
NOTE: If you connect the diskette drive after turning on the computer, it will take about 10 seconds for the computer to recognize the drive. Do not disconnect and reconnect before 10 seconds has elapsed.
4-2

Using optical media drives

Disconnecting 3 1/2" diskette drive
When you have finished using the diskette drive, follow the procedures below to disconnect it:
1. Wait for the indicator light to go out to make sure all diskette activity has stopped.
CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive.
2. Click the Safety Remove Hardware icon on the Task Bar.
3. Click Diskette drive.
4. Pull the diskette drive connector out of the USB port.
Using optical media drives
The full-size drive provides high-performance execution of CD/DVD-ROM-based programs. You can run either 12 cm (4.72") CD/DVDs or 8 cm (3.15") CD without an adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.
NOTE: Use the WinDVD 4 application to view DVD-Video discs.
O
PERATING
If you have a CD-RW/DVD-ROM drive, refer also to the Writing CDs section for precautions on writing to CDs.
B
ASICS
4-3
User's Manual
m
Loading discs
To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7.
1. a. When the power is on, press the DVD-ROM eject button to open the
drawer slightly.
EJECT BUTTON
Figure 4-3 Pressing the DVD-ROM eject button
b. Pressing the eject button will not open the drawer when the DVD-ROM
drive’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the left of the eject button.
OPERATING BASICS
4-4
15mm
Diameter 1.0m
Figure 4-4 Manual release with the eject hole
Using optical media drives
2. Pinch the drawer gently and pull until it is fully opened.
Figure 4-5 Pulling the drawer open
3. Lay the CD/DVD, label side up, in the drawer.
Figure 4-6 Inserting a CD/DVD
NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-6.
O
PERATING
B
ASICS
4-5
User's Manual
CAUTIONS: 1. Do not touch the laser lens. Doing so could cause
misalignment.
2. Be careful to keep foreign matter from entering the drive. Check the back edge of the tray to make sure it carries no debris before closing the drive.
4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base.
5. Push the center of the drawer to close it. Press gently until it locks into place.
CAUTION: If the CD/DVD is not seated properly when the drawer is closed, the CD/DVD might be damaged. Also, the drawer might not open fully when you press the eject button.
OPERATING BASICS
Figure 4-7 Closing the CD/DVD drawer
Removing discs
To remove the CD/DVD, follow the steps below and refer to figure 4-8.
CAUTION: Do not press the eject button while the computer is accessing the Fixed DVD-ROM drive. Wait for the Disk indicator to go out before you open the drawer. Also, if the CD/DVD is spinning when you open the drawer, wait for it to stop before you remove it.
1. To pop the drawer partially open, press the eject button. Gently pull the drawer out until it is fully opened.
4-6

Writing CDs on CD-RW/DVD-ROM drive

CAUTIONS: 1. When the drawer pops open slightly, wait a moment to
make sure the CD/DVD has stopped spinning before pulling the drawer fully open.
2. Turn off the power before you use the eject hole. If the CD/DVD is spinning when you open the drawer, the CD/DVD could fly off the spindle and cause injury.
2. The CD/DVD extends slightly over the sides of the drawer so you can grasp it. Hold the CD/DVD gently and lift it out.
Figure 4-8 Removing a CD/DVD
3. Push the center of the drawer to close it. Press gently until it locks into place.
Writing CDs on CD-RW/DVD-ROM drive
Depending on the type of drive installed, you may be able to write CDs. The CD­RW/DVD-ROM drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs. For information on loading and unloading CDs refer to the Using optical media drive section.
NOTE: CD-R discs can be written to only once. CD-RW discs can be rewritten many times.
O
PERATING
B
ASICS
4-7
User's Manual
Before writing or rewriting
Please observe the following points when you write or rewrite the data.
We recommend the following manufacturers of CD-R and CD-RW media.
Media quality can affect write or rewrite success rates.
CD -R: TAIYO YUDEN CO., LTD.
Mitsui Chemicals Inc. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd.
CD-RW: MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufac­turers above. Operation of other media cannot be guaranteed.
CD-RW can generally be rewritten about 1,000 times. However, the actual
number of rewrites is affected by the quality of the media and the way it is used.
Be sure to connect the universal AC adaptor when you write or rewrite. Be sure to close all other software programs except the writing software. Do not run software such as a screen saver which can put a heavy load on the
CPU.
Operate the computer at full power. Do not use power-saving features. Do not write while virus check software is running. Wait for it to finish, then
disable virus detection programs including any software that checks files automatically in the background.
Do not use hard disk utilities, including those intended to enhance HDD
OPERATING BASICS
access speed. They may cause unstable operation and damage data.
Write from the computer's HDD to the CD. Do not try to write from shared
devices such as a LAN server or any other network device.
Writing with software other than Drag'n Drop CD has not been confirmed.
Therefore, operation with other software cannot be guaranteed.
When writing or rewriting
Note the following when you write or rewrite a CD-R or CD-RW.
Always copy data from the HDD to the CD. Do not use cut-and-paste. The
original data will be lost if there is a write error.
4-8

Writing CD/DVDs on DVD-R/-RW drive

Do not perform any of the following actions:
• Operate the computer for any other function, including use of a mouse or Touch Pad, closing/opening the LCD panel.
• Start a communication application such as a modem.
• Apply impact or vibration to the PC.
• Install, remove or connect external devices, including the following: PC card, USB devices, external display, optical digital devices.
• Use the CD/MP3 control buttons to reproduce music and voice.
• Open the optical media drive.
If the media is poor in quality, dirty or damaged, writing or rewriting errors may
occur.
Set the computer on a level surface and avoid places subject to vibration such
as airplanes, trains, or cars. Do not use an unstable surface such as a stand.
Keep mobile phones and other wireless communication devices away from the
computer.
Writing CD/DVDs on DVD-R/-RW drive
You can use the DVD-R/-RW drive to write data to either CD-R/RW or DVD-R/-RW discs. The following applications for writing are supplied on CD-ROM: Drag'n Drop CD, licensed by Easy Systems Japan Ltd., and DigiOn Inc.
Important message
Before you write or rewrite to CD-R/RW or DVD-R/-RW disc, read and follow all set-up and operating instructions in this section. If you fail to do so, the DVD-R/­RW drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage.
Disclaimer
TOSHIBA does not bear responsibility for the following:
Damage to any CD-R/RW or DVD-R/-RW disc that may be caused by writing
or rewriting with this product.
4-9
O
PERATING
B
ASICS
User's Manual
Any change or loss of the recorded contents of CD-R/RW or DVD-R/-RW disc
that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.
Damage that may be caused by using third party equipment or software.
Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. Also, it is a good idea to make two or more copies of important data, in case of undesired change or loss of the recorded contents.
OPERATING BASICS
4-10
Writing CD/DVDs on DVD-R/-RW drive
Read/write function chart
Disc type CD -R CD- RW DVD-R DVD-RW DVD-RAM DVD+R DVD+RW
Read Write Drag’n Drop CD*1
*1 Software supplied with the product can be used for writing to a disc.
Yes Yes Yes Yes Yes Yes
Yes Yes Yes
Yes Yes Yes
Yes
No No No No
No No No No
OPERATING BASICS
4-11
User's Manual
Based on TOSHIBA's limited compatibility testing, we suggest the following
manufacturers of CD-R/RW and DVD-R/-RW disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
CD -R: TAIYO YUDEN CO., LTD.
Mitsui Chemicals Inc. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd.
CD-RW: MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
DVD-R: DVD Specifications for Recordable Disc for General
Version 2.0
TAIYO YUDEN CO., LTD. PIONEER VIDEO CORPORATION MITSUBISHI CHEMICAL CORPORATION
DVD-RW: DVD Specifications for Re-recordable Disc for Version
1.1
VICTOR COMPANY OF JAPAN, LIMITED. TDK Corporation
If the disc is poor in quality, dirty or damaged, writing or rewriting errors may
occur. Be careful to check the disc for dirt or damage before you use it.
The actual number of rewrites to CD-RW or DVD-RW is affected by the quality
of the disc and the way it is used.
There are two types of DVD discs: authoring and general use discs. Do not use
OPERATING BASICS
authoring discs. Only general use discs can be written to by a computer drive.
Other DVD-ROM drives for computers or other DVD players may not be able
to read DVD-R/-RW discs.
You cannot partially delete any data written to a DVD-RW disc. Data written to a CD-R/DVD-R disc cannot be deleted either in whole or in part. Data deleted (erase) from a CD-RW and DVD-RW disc cannot be recovered.
Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive.
In writing to a DVD-R/-RW disc, some disc space is required for file
management, so you may not be able to write the full capacity of the disc.
4-12
Writing CD/DVDs on DVD-R/-RW drive
Since the disc is based on the DVD standard, it might be filled with dummy data
if the written data is less than about 1 GB. Even if you write only a small amount of data, it might take time to fill in the dummy data.
Before writing or rewriting
Please observe the following points when you write or rewrite data.
Be sure to connect the universal AC adaptor before you write or rewrite. Be sure to close all other software programs except the writing software. Do not run software such as a screen saver, which can put a heavy load on the
CPU.
Operate the computer in the full-power mode. Do not use power-saving
features.
Do not write while virus check software is running. Wait for it to finish, then
disable virus detection programs including any software that checks files automatically in the background.
Do not use hard disk utilities, including those intended to enhance HDD
access speed. They may cause unstable operation and data damage.
Write from the computer's HDD to the CD/DVD. Do not try to write from shared
devices such as a LAN server or any other network device.
Writing with software other than Drag'n Drop CD+DVD is not recommended.
O
PERATING
When writing or rewriting
Please observe/consider the following when you write or rewrite to a CD-R/RW or DVD-R/-RW disc.
Do not perform any of the following actions when writing or rewriting:
• Operate the computer for any other function, including using a mouse or Touch Pad or closing/opening the LCD panel.
• Start a communication application such as a modem.
• Apply impact or vibration to the computer.
• Install, remove or connect external devices, including the following: PC card, USB devices, external display, optical digital devices.
• Use the Audio/Video control button to reproduce music or voice.
Do not use standby/hibernation while writing or rewriting.
4-13
B
ASICS
User's Manual
Make sure writing or rewriting is completed before going into standby/
hibernation.
Set the computer on a level surface and avoid places subject to vibration such
as airplanes, trains, or cars. Do not use an unstable surface such as a stand.
Keep mobile phones and other wireless communication devices away from the
computer.
Drag’n Drop CD+DVD
Note the following limitations when you use Drag'n Drop CD+DVD:
DVD-Video cannot be created using Drag'n Drop CD+DVD. DVD-Audio cannot be created using Drag'n Drop CD+DVD. You cannot use Drag'n Drop CD+DVDs music CD function to record music to a
DVD-R/-RW disc.
Do not use the DISC Backup function of Drag'n Drop CD+DVD to copy DVD-
Video and DVD-ROM with copyright protection, because the copy will not play correctly.
You cannot backup a CD-ROM or CD-R/RW to DVD-R/-RW using the DISC
Backup function of Drag'n Drop CD+DVD.
You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW to CD-R/RW
using the DISC Backup function of Drag'n Drop CD+DVD.
Drag'n Drop CD+DVD cannot record in packet format. You might not be able to use the DISC backup function of Drag'n Drop
CD+DVD to back up a DVD-R/-RW disc that was made with other software on a different DVD-R/-RW recorder.
OPERATING BASICS
Data Verification
To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD.
1. Right-click Data BOX and select Options to display the DATA DISC Option window.
2. Mark the Record and Verify check box and select Byte compare.
3. Click the OK button.
The “Record and Verify” function automatically checks whether data has been correctly recorded onto a CD/DVD. "Byte compare" compares the original data file with the data recorded on the CD/DVD and checks that the data completely matches.
4-14

Media care

Media care
This section provides tips on protecting data stored on your CD/DVDs and diskettes.
Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them:
CD/DVDs
1. Store your CD/DVDs in the container they came in to protect them and keep them clean.
2. Do not bend the CD/DVD.
3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD/DVD that contains data.
4. Hold the CD/DVD by its outside edge or the edge on the center hole. Finger­prints on the surface can prevent the drive from properly reading data.
5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy objects on your CD/DVDs.
6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth. Wipe from the center out, do not wipe in a circular direction around the CD/ DVD. If necessary, use a cloth dampened in water or a neutral cleaner. Do not use benzine, thinner or similar cleaner.
O
PERATING
Diskettes
1. Store your diskettes in the container they came in to protect them and keep them clean. If a diskette is dirty, do not use cleaning fluid. Clean it with a soft damp cloth.
2. Do not slide back the diskette’s protective metal covering or touch the diskette’s magnetic surface. Fingerprints may prevent the diskette drive from reading data from the diskette.
3. Data may be lost if the diskette is twisted; bent; or exposed to direct sunlight, extreme heat or cold.
4. Do not place heavy objects on your diskettes.
5. Do not eat, smoke, or use erasers near your diskettes. Foreign particles inside the diskette’s jacket can damage the magnetic surface.
B
ASICS
4-15
User's Manual
6. Magnetic energy can destroy the data on your diskettes. Keep your diskettes away from speakers, radios, television sets and other sources of magnetic fields.

Modem

This section describes how to connect and disconnect the internal modem to and from a telephone jack.
NOTE: The internal modem does not support voice functions. All data and fax functions are supported.
CAUTIONS: 1. In case of a lightning storm, unplug the modem cable
from the telephone jack.
2. Do not connect the modem to a digital telephone line. A digital line will damage the modem.
Region selection
Telecommunication regulations vary from one region to another, so you will need to make sure the internal modem’s settings are correct for the region in which it will be used.
To select a region, follow the steps below.
1. Click start, point to All Programs, point to TOSHIBA Internal Modem and click Region Select Utility.
NOTE: Do not use the Country/Region Select function in the Modem
OPERATING BASICS
setup utility in the Control Panel if the function is available. If you change the Country/Region in the Control Panel, the change may not take effect.
2. The Region Selection icon will appear in the Windows Task Bar.
Figure 4-9 The Region Selection icon
4-16
Modem
3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location.
4. Select a region from the region menu or a telephony location from the sub­menu.
• When you click a region it becomes the modem’s region selection, and the New Location for telephony will be set automatically.
• When you select a telephony location, the corresponding region is automati­cally selected and it becomes the modem’s current region setting.
Properties menu
Click the icon with the secondary mouse button to display the following menu.
Figure 4-10 The menu list
O
PERATING
B
ASICS
4-17
User's Manual
Setting
You can enable or disable the following settings:
AutoRun Mode
The Region Select utility starts automatically when you start up the operating system.
Open the Dialing Properties dialog box after selecting region.
The dialing properties dialog box will be displayed automatically after you select the region.
Location list for region selection.
A submenu appears displaying location information for telephony.
Open dialog box, if the modem and Telephony Current Location region code do not match.
A warning dialog box is displayed if current settings for region code and telephony location are incorrect.
Modem Selection
If the computer cannot recognize the internal modem, a dialog box is displayed. Select the COM port for your modem to use.
Dialing Properties
Select this item to display the dialing properties.
OPERATING BASICS
CAUTION: If you are using the computer in Japan, the Telecommunica­tions Business Law requires that you select Japan region mode. It is illegal to use the modem in Japan with any other selection.
Connecting
To connect the internal modem cable, follow the steps below.
1. Plug one end of the modular cable into the modem jack.
2. Plug the other end of the modular cable into a telephone jack.
4-18
Loading...