Toshiba P200 User Manual

User’s Manual

P200

computers.toshiba-europe.comcomputers.toshiba-europe.com

Copyright

Disclaimer

P200

© 2007 by TOSHIBA Corporation. All rights reserved. Under copyright law,
this manual cannot be reproduced in any form without the prior written
permission of TOSHIBA. No patent liability is assumed, with respect to the
use of the information contained herein.

P200 Portable Personal Computer User's Manual

First edition March 2007
Ownership and copyright of music, video computer programs, databases,

etc. are protected by the copyright laws. These copyrighted materials may
be copied for private use at home only. If, beyond the limitation above, you
copy (including to transform data formats) or modify these materials,
transfer them or distribute them via the Internet without approval of
copyright owners, you may be subject to claims for compensation for
damage and/or criminal penalties due to infringements of copyrights or
personal rights. Please remember to observe the copyright laws when you
use this product to copy the copyrighted works or perform other actions.
Please note that you may infringe the owner's rights protected by the
copyright laws if you use the screen mode switching functions (e.g. Wide
mode, Wide Zoom mode, etc.) of this product to display enlarged images/
video at coffee shops or hotels for the purposes of profits or providing these
to the public.

This manual has been validated and reviewed for accuracy. The
instructions and descriptions it contains are accurate for the P200 Portable
Personal Computers at the time of this manual’s production. However,
succeeding computers and manuals are subject to change without notice.
TOSHIBA assumes no liability for damages incurred directly or indirectly
from errors, omissions or discrepancies between the computer and the
manual.

Trademarks

IBM is a registered trademark and IBM PC, OS/2, and PS/2 are trademarks
of International Business Machines Corporation.

Celeron, Intel, Intel SpeedStep, Pentium, Intel Core and Centrino are
trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the United States and other countries.

MS-DOS, Microsoft, Windows and DirectX are registered trademarks and
Microsoft Vista is a Trademark of Microsoft Corporation.

Centronics is a registered trademark of Centronics Data Computer
Corporation. Photo CD is a trademark of Eastman Kodak.

Bluetooth is a trademark owned by its proprietor and used by TOSHIBA
under license.

iLINK is a trademark of Sony Corporation.

User’s Manual ii

Other trademarks and registered trademarks not listed above may be used
in this manual.

Macrovision License of Notice

This product incorporates copyright protection technology that is protected
by methods and claims of certain U.S. patents and other intellectual rights
owned by Macrovision Corporation, and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision
Corporation and is intended for home and other limited viewing uses only
unless authorized by Macrovision Corporation. Reverse engineering of
disassembly is prohibited.

Safety Instructions

Use the following safety guidelines to help protect yourself and your
computer.

When Using Your Computer

Do not operate your portable computer for an extended period of time with
the base resting directly on your body. With extended operation, heat can
potentially build up in the base. Allowing sustained contact with the skin
could cause discomfort or, eventually, a burn.

■ Do not attempt to service the computer yourself. Always follow

installation instructions closely.

■ Do not carry a battery in your pocket, purse, or other container where

metal objects (such as car keys) could short-circuit the battery
terminals. The resulting excessive current follow can cause extremely
high temperatures and may result in damage from burns.

■ Be sure that nothing rests on your AC adapter's power cable and that

the cable is not located where it can be tripped over or stepped on.

■ Place the AC adapter in a ventilated area, such as a desk top or on the

floor, when you use it to run the computer or to charge the battery. Do
not cover the AC adapter with papers or other items that will reduce
cooling; also, do not use the AC adapter while it is inside a carrying
case.

■ Use only the AC adapter and batteries that are approved for use with

this computer. Use of another type of battery or AC adapter may risk fire
or explosion.

■ Before you connect the computer to a power source, ensure that the

voltage rating of the AC adapter matches that of the available power
source.

115V/60Hz in most of North and South America and some Far Eastern
countries such as Taiwan.

100 V/50Hz in eastern Japan and 100 V/60Hz in western Japan.
230 V/50 Hz in most of Europe, the Middle East, and the Far East.

P200

User’s Manual iii

P200

■ If you use an extension cable with your AC adapter, ensure that the total

ampere rating of the products that are plugged into it do not exceed the
ampere rating of the extension cable itself.

■ To help avoid the potential hazard of electric shock, do not connect or

disconnect any cables or perform maintenance or reconfiguration of this
product during an electrical storm.

■ When setting up the computer for work, place it on a level surface.

■ Do not dispose of batteries in a fire. They may explode. Check with

local authorities for disposal instructions.

■ When travelling, do not check the computer as baggage. You can put

your computer through an X-ray security machine, but never put your
computer through a metal detector. If you have the computer checked
by hand, be sure to have a charged battery available in case you are
asked to turn on the computer.

■ When travelling with the hard drive removed from the computer, wrap

the drive in a non-conducting material, such as cloth or paper. If you
have the drive checked by hand, be ready to install the drive in the
computer. Your can put the hard drive through an X-ray security
machine, but never put it through a metal detector.

■ When travelling, do not place the computer in overhead storage

compartments where it could slide around. Do not drop your computer
or subject it to other mechanical shocks.

■ Protect your computer, battery, and hard drive from environmental

hazards such as dirt, dust, food, liquids, temperature extremes, and
overexposure to sunlight.

■ When you move your computer between environments with very

different temperature and/or humidity ranges, condensation may form
on or within the computer. To avoid damaging the computer, allow
sufficient time for the moisture to evaporate before using the computer.

■ When you disconnect a cable, pull on its connector or on its strain relief

loop, not on the cable itself. As you pull out the connector, keep it
evenly aligned to avoid bending any connector pins. Also, before you
connect a cable make sure both connectors are correctly oriented and
aligned.

■ Before you clean your computer, turn if off, unplug it from its power

source, and remove the battery.

■ Handle components with care. Hold a component such as a memory

module by its edges, not its pins.

When using telephone equipment in conjunction with your computer, basic
safety precautions should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the following:

■ Do not use this product near water, for example, near a bathtub,

washing bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.

■ Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lightning.

User’s Manual iv

■ Do not use the telephone to report a gas leak in the vicinity of the leak.

■ Use only the power cord indicated in this manual.

■ Replace only with the same or equivalent type battery recommended by

the manufacturer.

■ Dispose of used batteries according to the manufacturer's instructions.

■ To reduce the risk of fire, use only No. 26 AWG or larger

telecommunication line cord.

Use only the battery pack that came with the computer or an optional
battery pack. Use of the wrong battery could damage your computer.

TOSHIBA assumes no liability for any damage in such case.

EU Declaration of Conformity

This product is carrying the CE-Mark in accordance with the related
European Directives. Responsible for CE-Marking is TOSHIBA Europe
GmbH, Hammfelddamm 8, 41460 Neuss, Germany.

The complete and official EU Declaration of Conformity can be found on
TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.

CE compliance

This product is labelled with the CE Mark in accordance with the related
European Directives, notably Electromagnetic Compatibility Directive
89/336/EEC for the notebook and the electronic accessories including the
supplied power adapter, the Radio Equipment and Telecommunications
Terminal Equipment Directive 1999/5/EC in case of implemented
telecommunication accessories and the Low Voltage Directive 73/23/EEC
for the supplied power adapter.

This product and the original options are designed to observe the related
EMC (Electromagnetic Compatibility) and safety standards. However,
TOSHIBA cannot guarantee that this product still observes these EMC
standards if options or cables not produced by TOSHIBA are connected or
implemented. In this case the persons who have connected / implemented
those options / cables have to provide assurance that the system (PC plus
options / cables) still fulfils the required standards. To avoid general EMC
problems, the following guidance should be noted:

■ Only CE marked options should be connected / implemented

■ Only best shielded cables should be connected

P200

Working environment

This product was designed to fulfil the EMC (Electromagnetic Compatibility)
requirements to be observed for so-called "Residential, commercial and
light industry environments".

User’s Manual v

P200

TOSHIBA do not approve the use of this product in working environments
other than the above mentioned "Residential, commercial and light industry
environments".

For example, the following environments are not approved:

■ Industrial Environments (e.g. environments where a mains voltage of

380V three-phase is used)

■ Medical Environments

■ Automotive Environments

■ Aircraft Environments

If this product is supplied with a network port, please refer to the paragraph
"Network connection".

Any consequences resulting from the use of this product in working
environments that are not approved are not the responsibility of TOSHIBA.

The consequences of the use of this product in non-approved working
environments may be:

■ Interference with other devices or machines in the near surrounding

area.

■ Malfunction of, or data loss from, this product caused by disturbances

generated by other devices or machines in the near surrounding area.

Therefore TOSHIBA strongly recommend that the electromagnetic
compatibility of this product should be suitably tested in all non-approved
working environments before use. In the case of automobiles or aircraft, the
manufacturer or airline respectively should be asked for permission before
use of this product.

Furthermore, for general safety reasons, the use of this product in
environments with explosive atmospheres is not permitted.

Following information is only for EU-member states:

The symbol indicates that this product may not be treated as
household waste. Please ensure this product is properly
disposed as inappropriate waste handling of this product may
cause potential hazards to the environment and human health.
For more detailed information about recycling of this product,
please contact your local city office, your household waste
disposal service or the shop where you purchased the product.

This symbol may not stick depending on the country and region where you
purchased.

User’s Manual vi

Optical Disc Drive Safety Instruction

Be sure to check the international precautions at the end of this section.

The optical drive that is used in this computer is equipped with a laser
device. A classification label with the following sentence is affixed to the
surface of the drive.

CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A LASER DE CLASSE 1
KLASS 1 LASER APPARAT

The drive with the above label is certified by the manufacturer that the drive
complies with the requirement for laser product on the date of
manufacturing pursuant to article 21 of Code of Federal Regulations by the
United States of America, Department of Health & Human Services, Food
and Drug Administration.

In other countries, the drive is certified to comply with the requirement
pursant to IEC 825 and EN60825 on class 1 laser product.

This computer is equipped with one of the optical drive in the following list
according to the model.

P200

User’s Manual vii

TOSHIBA Samsung Storage Technology

CD-RW/DVD-ROM TS-L462D

■ The CD-RW/DVD-ROM drive employs a laser system. To ensure

proper use of this product, please read this instruction manual carefully
and retain for future reference. Should the unit ever require
maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

Location of the required label

SERIAL NO.
MANUFACTURED:

COMPLIES WITH FDA RADIATION
PERFORMANCE STANDARDS, 21 CFR
SUBCHAPTER J.

CLASS 1 LASER PRODUCT
LASER KLASSE 1

TOSHIBA Samsung Storage Technology
Korea Corporation
416, Maetan-3Dong, Yeongtong-Gu, Suwon City,
Gyeonggi-Do, 443-742, Korea

P200

User’s Manual viii

TEAC

CD-RW/DVD-ROM DW-224E

■ The CD-RW/DVD-ROM drive employs a laser system. To ensure

proper use of this product, please read this instruction manual carefully
and retain for future reference. Should the unit ever require
maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

Location of the required label

SERIAL NO.
MANUFACTURED:

COMPLIES WITH FDA RADIATION
PERFORMANCE STANDARDS, 21 CFR
SUBCHAPTER J.

CLASS 1 LASER PRODUCT
LASER KLASSE 1

TEAC CORPORATION
3-7-3 NAKA-CHO, MUSASHINO-SHI
TOKYO, JAPAN

P200

User’s Manual ix

Pioneer

DVD Super Multi DVR-K17

■ The DVD Super Multi drive employs a laser system. To ensure proper

use of this product, please read this instruction manual carefully and
retain for future reference. Should the unit ever require maintenance,
contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

Location of the required label

SERIAL NO.
MANUFACTURED:

COMPLIES WITH FDA RADIATION
PERFORMANCE STANDARDS, 21 CFR
SUBCHAPTER J.

CLASS 1 LASER PRODUCT
LASER KLASSE 1

PIONEER CORPORATION
4-1, MEGURO 1-CHOME
MEGURO-KU, TOKYO, 153-8654

P200

User’s Manual x

TOSHIBA Samsung Storage Technology

TS-L632D

■ The drive employs a laser system. To ensure proper use of this

product, please read this instruction manual carefully and retain for
future reference. Should the unit ever require maintenance, contact an
authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

Location of the required label

SERIAL NO.
MANUFACTURED:

COMPLIES WITH FDA RADIATION
PERFORMANCE STANDARDS, 21 CFR
SUBCHAPTER J.

CLASS 1 LASER PRODUCT
LASER KLASSE 1

TOSHIBA Samsung Storage Technology
Korea Corporation
416, Maetan-3Dong, Yeongtong-Gu, Suwon City,
Gyeonggi-Do, 443-742, Korea

P200

User’s Manual xi

Hitachi-LG Data Storage

DVD Super Multi GSA-T20N

■ The DVD Super Multi drive employs a laser system. To ensure proper

use of this product, please read this instruction manual carefully and
retain for future reference. Should the unit ever require maintenance,
contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

Location of the required label

SERIAL NO.
MANUFACTURED:

COMPLIES WITH FDA RADIATION
PERFORMANCE STANDARDS, 21 CFR
SUBCHAPTER J.

CLASS 1 LASER PRODUCT
LASER KLASSE 1

Hitachi-LG Data Storage, Inc.
22-23, Kaigan 3-chome, Minato-ku,
Yokyo, 108-0022 Japan

P200

User’s Manual xii

Panasonic

DVD Super Multi UJ-850U

■ The DVD Super Multi drive employs a laser system. To ensure proper

use of this product, please read this instruction manual carefully and
retain for future reference. Should the unit ever require maintenance,
contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

Location of the required label

SERIAL NO.
MANUFACTURED:

COMPLIES WITH FDA RADIATION
PERFORMANCE STANDARDS, 21 CFR
SUBCHAPTER J.

CLASS 1 LASER PRODUCT
LASER KLASSE 1

Panasonic Communications Co., Ltd.
1-62, 4-Chome Minoshima, Hakata-Ku
Fukuoka, Japan

P200

User’s Manual xiii

TEAC

DV-W28EC

■ The drive employs a laser system. To ensure proper use of this

product, please read this instruction manual carefully and retain for
future reference. Should the unit ever require maintenance, contact an
authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

Location of the required label

SERIAL NO.
MANUFACTURED:

COMPLIES WITH FDA RADIATION
PERFORMANCE STANDARDS, 21 CFR
SUBCHAPTER J.

CLASS 1 LASER PRODUCT
LASER KLASSE 1

TEAC CORPORATION
3-7-3 NAKA-CHO, MUSASHINO-SHI
TOKYO, JAPAN

P200

User’s Manual xiv

International Precautions

P200

CAUTION: This appliance contains a laser
system and is classified as a "CLASS 1 LASER
PRODUCT". To use this model properly, read the
instruction manual carefully and keep this manual
for your future reference. In case of any trouble
with this model, please contact your nearest
"AUTHORIZED service station". To prevent direct
exposure to the laser beam, do not try to open the
enclosure.

VORSICHT: Dieses Gerät enthält ein Laser­System und ist als „LASERSCHUTZKLASSE 1
PRODUKT“ klassifiziert. Für den richtigen
Gebrauch dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch und
bewahren diese bitte als Referenz auf. Falls
Probleme mit diesem Modell auftreten,
benachrichtigen Sie bitte die nächste „autorisierte
Service-Vertretung“. Um einen direkten Kontakt
mit dem Laserstrahl zu vermeiden darf das Gerät
nicht geöffnet werden.

ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at apparatet
arbejder med laserstråler af klasse 1, hviket
betyder, at der anvendes laserstrlier af svageste
klasse, og at man ikke på apparatets yderside kan
bilve udsat for utilladellg kraftig stråling.

APPARATET BOR KUN ÅBNES AF FAGFOLK
MED SÆRLIGT KENDSKAB TIL APPARATER
MED LASERSTRÅLER!

Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som advarer imod
at foretage sådanne indgreb i apparatet, at man
kan komme til at udsætte sig for laserstråling.

OBS! Apparaten innehåller laserkomponent som
avger laserstråining överstigande gränsen för
laserklass 1.

VAROITUS. Suojakoteloa si saa avata. Laite
sisältää laserdiodin, joka lähetää näkymätöntä
silmilie vaarallista lasersäteilyä.

CAUTION: USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE
SPECIFIED IN THE OWNER'S MANUAL MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.

User’s Manual xv

Modem warning notice

Conformity Statement

The equipment has been approved to [Commission Decision "CTR21"] for
pan- European single terminal connection to the Public Switched
Telephone Network (PSTN).

However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.

In the event of problems, you should contact your equipment supplier in the
first instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to confirm with the additional
requirements conditional in EG 201 121.

Germany ATAAB AN005, AN006, AN007, AN009, AN010 and

Greece ATAAB AN005, AN006 and GR01, 02, 03, 04
Portugal ATAAB AN001, 005, 006, 007, 011 and P03, 04, 08,

Spain ATAAB AN005, 007, 012, and ES01
Switzerland ATAAB AN002
Norway ATAAB AN002, 005, 007 and NO 01, 02

All other
countries/regions

Specific switch settings or software setup are required for each network,
please refer to the relevant sections of the user guide for more details.

The hookflash (timed break register recall) function is subject to separate
national type approvals. It has not been tested for conformity to national
type regulations, and no guarantee of successful operation of that specific
function on specific national networks can be given.

P200

VORSICHT: DIE VERWENDUNG VON
ANDEREN STEURUNGEN ODER
EINSTELLUNGEN ODER DAS DURCHFÜHREN
VON ANDEREN VORGÄNGEN ALS IN DER
BEDIENUNGSANLEITUNG BESCHRIEBEN
KÖNNEN GEFÄHRLICHE
STRAHLENEXPOSITIONEN ZUR FOLGE
HABEN.

DE03, 04, 05, 08, 09, 12, 14, 17

10

ATAAB AN003, 004

User’s Manual xvi

Important Notice

Copyrighted works including, but not limited to music, video, computer
program, databases are protected by copyright laws. Unless specifically
permitted under applicable copyright laws, you cannot copy, modify, assign,
transmit or otherwise dispose of any copyrighted work with the consent of
the owner of the copyright.

Please take notice that unauthorized copying, modification, assignment,
transmission and disposition may be subject to claims for damages and
penalties.

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and
withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.

Be certain to read the general precautions below and to note the cautions
included in the text of the manual.

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer
and any other items you are using, such as a printer.

Leave enough space around the computer and other equipment to provide
adequate ventilation. Otherwise, they may overheat.

To keep your computer in prime operating condition, protect your work area
from:

■ Dust, moisture, and direct sunlight.

■ Equipment that generates a strong electromagnetic field, such as

stereo speakers (other than speakers that are connected to the
computer) or speakerphones.

■ Rapid changes in temperature or humidity and sources of temperature

change such as air conditioner vents or heaters.

■ Extreme heat, cold, or humidity.

■ Liquids and corrosive chemicals.

P200

Stress injury

Carefully read the Instruction Manual for Safety and Comfort. It contains
information on the prevention of stress injuries to your hands and wrists
that can be caused by extensive keyboard use. Chapter 3, Getting Started,
also includes information on work space design, posture and lighting that
can help reduce physical stress.

User’s Manual xvii

Heat injury

■ Avoid prolonged physical contact with the computer. If the computer is

used for long periods, its surface can become very warm. While the
temperature will not feel hot to the touch, if you maintain physical
contact with the computer for a long time, for example if you rest the
computer on your lap or if you keep your hands on the palm rest, your
skin might suffer a low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with

the metal plate supporting the various interface ports as this can
become hot.

■ The surface of the AC adaptor can become hot when in use but this

condition does not indicate a malfunction. If you need to transport the
AC adaptor, you should disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat as the

material could become damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to any form of
strong impact as this can damage the computer's components or otherwise
cause it to malfunction.

PC Card overheating

Some PC Cards can become hot during prolonged use which may result in
errors or instability in the operation of the device in question. In addition,
you should also be careful when you remove a PC Card that has been
used for a long time.

P200

Mobile phones

Please be aware that the use of mobile phones can interfere with the audio
system. The operation of the computer will not be impaired in any way, but
it is recommended that a minimum distance of 30cm is maintained between
the computer and a mobile phone that is in use.

Instruction Manual for Safety and Comfort

All important information on the safe and proper use of this computer is
described in the enclosed Instruction Manual for Safety and Comfort. Be
sure to read it before using the computer.

User’s Manual xviii

Table of Contents

Chapter 1 P200 Features

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

TOSHIBA Value Added Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Utilities and Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Chapter 2 The Grand Tour

Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Front with the display open. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Keyboard Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Optical Disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

P200

Chapter 3 Getting Started

Connecting the AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Turning on the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Turning off the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Restarting the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

System Recovery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Restoring the preinstalled software from the

Product Recovery disc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

User’s Manual xix

P200

Chapter 4

Operating Basics

Using the TouchPad/Dual Mode Pad . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Dual Mode Pad Button function (Dual Mode Pad is

provided with some models). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Using the FingerPrint (FingerPrint sensor is provided

with some models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Using the Web Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Using the internal modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Using optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Writing CDs on a CD-RW/DVD-ROM drive . . . . . . . . . . . . . . . . . . . . 4-24

Writing CDs/DVDs on a DVD Super Multi drive

supporting double layer disc recording. . . . . . . . . . . . . . . . . . . . . . 4-26

When Using Ulead DVD MovieFactory® for TOSHIBA . . . . . . . . . . 4-30

TOSHIBA Disc Creator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32

Media Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33

Disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34

TV-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34

Setting up more than one display. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34

Cleaning the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35

Moving the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36

Chapter 5 The Keyboard

Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

F1 ... F12 function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Soft keys: Fn key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Number Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Generating ASCII characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Chapter 6 Power and Power-Up Modes

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Power indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Battery types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Care and use of the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14

Panel power off/on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14

System automatic Sleep/Hibernation . . . . . . . . . . . . . . . . . . . . . . . . 6-14

User’s Manual xx

P200

Chapter 7

HW Setup

Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

HW Setup Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Chapter 8 Optional Devices

Express Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

SD/SDHC/MMC/MS/MS Pro/xD Memory cards . . . . . . . . . . . . . . . . . . 8-3

Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

Additional battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8

Additional AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8

Battery charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8

External monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

i.LINK (IEEE1394a) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15

Chapter 9 Troubleshooting

Problem solving process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Hardware and system checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-18

Chapter 10 Disclaimers

CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

Memory (Main System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

HDD Drive Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Graphics Processor Unit ("GPU"). . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Non-applicable Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Copy Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

LCD Brightness and Eye Strain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4

Appendix A Specifications

Appendix B Display Modes

Appendix C AC Power Cord and Connectors

Appendix D If your computer is stolen

Glossary

User’s Manual xxi

Preface

Congratulations on your purchase of the P200 computer. This powerful
notebook computer provides excellent expansion capability, including
multimedia devices, and it is designed to provide years of reliable, high­performance computing.

This manual tells how to set up and begin using your P200 computer. It
also provides detailed information on configuring your computer, basic
operations and care, using optional devices and troubleshooting.

If you are a new user of computers or if you're new to portable computing,
first read over the P200 Features and The Grand Tour chapters to
familiarize yourself with the computer's features, components and
accessory devices. Then read Getting Started for step-by-step instructions
on setting up your computer.

If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted
with this manual by browsing through its pages. Be sure to look over the

Special features section of the P200 Features, to learn about features that

are unique to the computer.

P200

Manual contents

This manual has ten chapters, four appendixes and a glossary.
Chapter 1, P200 Features, is an overview of the computer's special

features, utilities, and options.
Chapter 2, The Grand Tour, identifies the components of the computer and

briefly explains how they function.
Chapter 3, Getting Started, provides a quick overview of how to begin

operating your computer and gives tips on safety and designing your work
area. Be sure to read the sections on setting up the operating system and
on restoring the pre-installed software.

Chapter 4, Operating Basics, includes instructions on using the following
devices: TouchPad/Dual Mode Pad, the optical disc drives, the internal
modem, LAN and wireless LAN. It also provides tips on care of the
computer, disks and DVD/CD-ROMs.

Chapter 5, The Keyboard, describes special keyboard functions including
the keypad overlay and hotkeys.

User’s Manual xxii

Chapter 6, Power and Power-Up Modes, gives details on the computer's
power resources.

Chapter 7, HW Setup, introduces you to the TOSHIBA Hardware Setup
program.

Chapter 8, Optional Devices, describes the optional hardware available.
Chapter 9, Troubleshooting, provides helpful information on how to perform

some diagnostic tests, and suggests courses of action if the computer
doesn't seem to be working properly.

Chapter 10, Disclaimers, provides disclaimer information related to your
computer.

The Appendices provide technical information about your computer.
The Glossary defines general computer terminology and includes a list of

acronyms used in the text.

Conventions

This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parentheses following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.

P200

Icons

Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.

Keys

The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, Enter identifies the Enter key.

Key operation

Some operations require you to simultaneously use two or more keys. We
identify such operations by the key top symbols separated by a plus sign
(+). For example, Ctrl + C means you must hold down Ctrl and at the same
time press C. If three keys are used, hold down the first two and at the
same time press the third.

DISKCOPY A: B: When procedures require an action such as

clicking an icon or entering text, the icon's name
or the text you are to type in is represented in the
type face you see to the left.

User’s Manual xxiii

Display

Names of windows or icons or text generated by
the computer that appears on its display screen is

ABC

presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.

Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.

Please read. A note is a hint or advice that helps you make best use of
your equipment.

Terminology

This term is defined in this document as follows:

P200

Start The word "Start" refers to the button in

Equipment checklist

Carefully unpack your computer. Save the box and packing materials for
future use. Check to make sure you have all the following items:

Hardware

■ P200 Portable Personal Computer

■ Universal AC Adapter and Power Cord

■ USB Floppy Disk Drive (provided with some models)

■ Modular cable for modem (provided with some models)

Microsoft® Windows Vista™.

User’s Manual xxiv

Software

Microsoft® Windows Vista™ Home Basic/Home Premium/Business Edition

■ The following software which is pre-installed on your hard disk:

■ Microsoft

Edition

■ DVD Video Player

■ TOSHIBA Disc Creator

■ TOSHIBA ConfigFree

■ TOSHIBA Assist

■ TOSHIBA SD Memory Card Format*

■ TOSHIBA HW Setup

■ TOSHIBA Value Added Package Utility

■ TOSHIBA Supervisor Password Utility

■ Ulead DVD MovieFactory

■ FingerPrint Utility*

■ Online Manual

■ Product Recovery disc (provided with some models)

* The availability of this software is dependent on the model you

purchased.

The system may not function properly if you use drivers that are not pre­installed or distributed by TOSHIBA.

®

Windows Vista™ Home Basic/Home Premium/Business

®

P200

SD Memory Card Format Utility and other SD functions are packaged into
TOSHIBA SD Memoory Utilities. When uninstalling the SD utilities, click
Start  Control Panel  Uninstall a program, and select TOSHIBA SD
Memory Utilities.

Documentation and Backup Media

■ Your computer's documentation:

■ P200 Personal Computer User's Manual

■ P200 Quickstart

■ Instruction Manual for Safety and Comfort

■ Microsoft

■ Warranty Information

■ Product Recovery DVD-ROM

If any of the items are missing or damaged, contact your dealer
immediately.

User’s Manual xxv

®

Windows Vista™ Quick Start Guide

P200 Features

This chapter identifies the computer's special features, options and
accessories.

Basic features are described in a separate pamphlet.

Some of the features described in this manual may not function properly if
you use an operating system that was not pre-installed by TOSHIBA.

Features

Please visit your region's web site for the configuration details of the model
that you have purchased.

P200 Features

Chapter 1

Processor

Depending on the model you purchased:

®

Core™ 2 Duo Processor

Intel
Intel® Core™ Duo Processor

®

Pentium® Dual Core Processor

Intel

®

Celeron® M Processor

Intel

Disclaimer (CPU)

For more information on the Disclaimer regarding CPU, please refer to the

Disclaimers section in Chapter 10.

User’s Manual 1-1

P200 Features

Chipset

Mobile Intel® 945GM/PM, 943GML Express
Chipset

T1 CardReader & 1394a Controller PCI8402
Realtek High Definition Audio Codec ALC861D
Realtek 10M/100M/1Gbps LAN Controller

RTL8111B, 10M/100M LAN Controller RTL8101E

Memory

The graphics system in your computer may use part of the main system
memory for graphics performance and therefore reduce the amount of
system memory available for other computing activities. The amount of
system memory allocated to support graphics may vary depending on the
graphics system, applications utilized, system memory size and other
factors.

Slot Two DDRII SO-DIMM, up to 4GB with Intel

945PM/GM Express Chipset; up to 2GB with Intel
943GML Express Chipset can be upgraded
through the memory expansion slot.

You need to remove the existing SO-DIMM if your
system is already equipped with the maximum
amount of memory modules.

The maximum upgradable system memory is
depending on the system you purchased.

L2 Cache Depending on the model you purchased.

®

Core™ 2 Duo Processor with 4MB or 2MB

Intel
L2 Cache

®

Intel

Core™ Duo Processor with 2MB L2 Cache

®

Pentium® Dual Core Processor with 2MB

Intel
L2 Cache

®

Intel

Merom Celeron® M processor with 1MB L2

Cache.

Video RAM Depending on the model you purchased:

®

Mobile Intel

945GM/943GML Express Chipset,

up to 128MB shared with main memory.
Nvidia GeForce7600

up to 64MB shared with main memory
(for 256MB main memory),
up to 128MB shared with main memory
(for 512MB, 756MB main memory),
up to 256MB shared with main memory
(for more than 1GB main memory).

®

User’s Manual 1-2

P200 Features

BIOS

1MB Flash ROM for system BIOS
Suspend to memory or hard disk drive
Various Hotkey functions for system control
Complete ACPI 1.0b functionality

Power

Battery Pack 6-cell Lithium Ion smart battery pack with

10.8V*4000mAh
9-cell Lithium Ion smart battery pack with

10.8V*6000mAh
Approximately 12 hours or longer charging time to

100% battery capacity with system switched on.
Approximately 4 hours charge time to 100%

battery capacity with system switched off.
Approximately 1.5 days discharging time in Sleep

Mode for the 9-cell battery, 1 day for the 6-cell
battery.

Discharge time in shutdown mode is
approximately 1 month

* The availability of this battery is dependent on

the model you purchased.

Disclaimer (Battery Life)

For more information on the Disclaimer regarding Battery Life, please refer
to the Disclaimers section in Chapter 10.

RTC Battery The computer has an internal battery to back up

its Real Time Clock (RTC), calender and setup
information. This battery will last for an average of
one month with no external power source.

AC adapter The universal AC adapter provides power to the

system and recharges the batteries when they
are low. It comes with a detachable power cord.

Floppy Disk Drive devices

External USB Floppy Disk Drive (depends on the
model purchased)

User’s Manual 1-3

P200 Features

TouchPad/Dual Mode Pad

A TouchPad/Dual Mode Pad and control buttons
in the palm rest enable control of the on-screen
pointer.

The Dual Mode Pad is a TouchPad that provides
normal touchpad features in its default mode and
switches to a DualMode interface when the upper
right corner of the TouchPad is tapped. Tapping
the same corner again will revert to normal
pointing mode.

The volume control on the right side of the TouchPad and print button may
not function with some applications.

Display

17" TFT screen with a resolution of
1440 horizontal × 900 vertical pixels WXGA+.

Disclaimer (LCD)

For more information on the Disclaimer regarding LCD, please refer to the

Disclaimers section in Chapter 10.

Graphics controller Nvidia GeForce7600 (Graphics controller chipset

depends on the model purchased)
The graphics controller maximizes display

performance. Refer to Display Modes section in
Appendix B for more information.

Disclaimer (Graphics Processor Unit ("GPU")

For more information on the Disclaimer regarding Graphic Processor Unit
("GPU"), please refer to the Disclaimers section in Chapter 10.

User’s Manual 1-4

P200 Features

Disks

Fixed hard disk 9.5mm 2.5" hard disk drive

(60/80/100/120/160/200 GB)

12.5mm 2.5" hard disk drive
(160/200/250/300 GB)
Serial ATA 1.5 Gb/s

Disclaimer (HDD Drive Capacity)

For more information on the Disclaimer regarding HDD Drive Capacity,
please refer to the Disclaimers section in Chapter 10.

CD-RW/DVD-ROM
drive

Some models are equipped with a full-size
CD-RW/DVD-ROM module that lets you record
data to rewritable CD/CD-RWs as well as run
either 12cm (4.72") or 8cm (3.15") CD/DVDs
without using an adapter. It reads DVD-ROMs at
maximum 8x speed and CD-ROMs at maximum
24x speed. It writes CD-Rs at up to 24x speed,
CD-RWs at up to 24x speed. This drive supports
the following formats:

■ DVD-ROM ■ DVD-Video

■ CD-R ■ CD-RW

■ CD-DA ■ CD-Text

■ Photo CD (single/multi-session)

■ CD-ROM Mode1, Mode2

■ CD-ROMXA Mode2 (Form1, Form2)

■ Enhanced CD(CD-EXTRA)

User’s Manual 1-5

P200 Features

DVD Super Multi drive
supporting

R Double

ٛ

Layer

Some models are equipped with a full-size DVD
Super Multi drive supporting ±R Double Layer
module with dual layer support that lets you
record data to rewritable CD/DVDs as well as run
either 12cm (4.72") or 8cm (3.15") CD/DVDs
without using an adapter. It reads DVD-ROMs at
maximum 8x speed and CD-ROMs at maximum
24x speed. It writes CD-Rs at up to 24x speed,
CD-RWs at up to 16x speed, DVD-Rs at
maximum 8x speed, DVD-RWs at maximum 6x
speed, DVD+RWs at maximum 8x speed,
DVD+Rs at maximum 8x speed, DVD+R (double
layer) at maximum 4x speed, DVD-R (dual layer)
at maximum 4x speed and DVD-RAM at
maximum 5x speed. This drive supports the same
formats as the CD-RW/DVD-ROM drive plus the
following:

■ DVD-ROM ■ DVD-Video

■ DVD-R ■ DVD-RW

■ DVD+R ■ DVD+RW

■ DVD-RAM ■ DVD+R (double layer)

■ CD-R ■ CD-RW

■ CD-DA ■ CD-Text

■ DVD-R (dual layer)

■ Photo CD (single/multi-session)

■ CD-ROM Mode1, Mode2

■ CD-ROMXA Mode2 (Form1, Form2)

■ Enhanced CD (CD-EXTRA)

Computers in this series can be configured with multiple types of optical
disc drive. For more information on the optical disc drives available, talk to
your dealer. More information on using the optical disc drive can be found
in Chapter 4, Operating Basics.

Slots (depending on configuration)

Multiple Digital Media
Card (SD/SDHC/MMC/
MS/MS Pro/xD)

User’s Manual 1-6

This slot lets you easily transfer data from
devices, such as digital cameras and Personal
Digital Assistants, that use flash-memory.

You can use a memory module in this slot.

P200 Features

Express Card The Express Card expansion slot that can

accommodate two standard module formats; an
Express Card/34 module and an Express Card/54
module. An Express Card module is a small addin
card technology based on the PCI Express and
Universal Serial Bus (USB) interfaces.

Ports (depending on configuration)

External monitor 15-pin analog VGA port supports VESA DDC2B

compatible functions.

Universal Serial Bus The computer has Four Universal Serial Bus

(USB) ports that comply with the USB 2.0
standard, which enables data transfer speeds
more than 40 times faster than USB 1.1 (which
this computer also supports).

i.LINK (IEEE1394a) This port enables high-speed data transfer

TV Out The 4-pin S-Video port is compatible with PAL or

directly from external devices such as digital
video cameras.

NTSC TV standard, supporting Macrovision 7.02
copy protection.

Multimedia

Sound system The integrated Windows® compatible sound

Headphone jack A standard 3.5mm stereo jack is provided for the

Microphone jack A standard 3.5 mm mini microphone jack enables

Web Camera Record/Send still or video images with this

system provides support for internal speakers as
well as jacks for an external microphone and
headphones.

connection of external headphones or speakers.

connection of monaural microphone input.

integrated Web Camera.
(Depending on configuration)

Communications (depending on configuration)

Modem An internal modem provides capability for data

User’s Manual 1-7

and fax communication. It supports the V.90 or
V.92 standards depending on the region and
provides a modem jack for connection to a
telephone line. The speed of data and fax transfer
depends on the analog telephone line conditions.

P200 Features

LAN The computer has built-in support for Ethernet

Wireless LAN The computer has a built-in wireless LAN mini-

Bluetooth Bluetooth is a short-range wireless technology

LAN (10 Mbps, 10BASE-T), Fast Ethernet LAN
(100 Mbps 100BASE-TX), or Gigabit Ethernet
LAN (1000 Mbps, 1000BASE-T).

PCIE card that is compatible with other LAN
systems that support the following: 802.11a/b/g/n
wireless LAN module/ 802.11a/b/g wireless LAN
module/ 802.11b/g wireless LAN module. It has a
Frequency Channel Selection (2.4 or 5 GHz) and
allows roaming over multiple channels.

used to create PANs (Personal Area Networks)
among your devices, and with other nearby
devices like mobile computers, mobile phones,
and digital cameras.

Security

Power-on password protection
Two level password architecture
Fingerprint authentication

Security Lock Slot

Receives an optional security lock in order to
anchor the computer to a desk or other large,
heavy object.

Special features

The following features are either unique to TOSHIBA computers or are
advanced features, which make the computer more convenient to use.

Hotkeys Key combinations that let you quickly modify the

Display Automatic
Power off

User’s Manual 1-8

system configuration directly from the keyboard
without running a system configuration program.

This feature automatically cuts off power to the
internal display when there is no input from the
keyboard or pointing device for a specified time
period. Power is restored when any key is
pressed or when there is input from a pointing
device. You can specify the time period in the
TOSHIBA Power Saver utility.

P200 Features

Hard Disk Drive
Automatic Power Off

This feature automatically cuts off power to the
hard disk drive when it is not accessed for a
specified time period. Power is restored when the
hard disk is accessed. You can specify the time
period in the TOSHIBA Power Saver utility.

System Automatic
Sleep/Hibernation

This feature automatically places the system into
either Sleep Mode or Hibernation Mode when
there is no input or hardware access for a
specified time period. You can specify the time
period and select either System Sleep or System
Hibernate in the TOSHIBA Power Saver utility.

Keypad Overlay A ten-key pad is integrated into the keyboard.
Power-on Password Two levels of password security are available,

Supervisor and User, which can prevent
unauthorized access to your computer.

Battery Save Mode This feature lets you save battery power. You can

specify the level of system power management in
the TOSHIBA Power Saver utility.

Instant Security A Hotkey function which blanks the screen and

activates password security to provide quick and
easy data security.

Panel Power Off/On This feature turns power to the computer off when

the display panel is closed and turns it back on
when the panel is opened. You can specify the
setting in the TOSHIBA Power Saver utility.

Low Battery
Automatic
Hibernation

When battery power is exhausted to the point that
computer operation cannot be continued, the
system automatically enters Hibernation Mode
and shuts itself down. You can specify the setting
in the TOSHIBA Power Saver utility.

Hibernation This feature lets you turn off the power without

exiting from your software. The contents of main
memory are saved to the hard disk. When you
turn on the power again, you can continue
working right where you left off. Refer to the

Turning off the power section in Chapter 3,
Getting Started, for details.

Sleep In Sleep Mode, power to the system remains on,

but the processor and all other devices are
effectively in 'sleep mode'. When the computer is
in Sleep Mode, the Power LED flashes amber.
The computer enters Sleep Mode regardless of
the Hibernate Mode setting. Refer to the Turning
off the power section in Chapter 3, Getting
Started, for details..

User’s Manual 1-9

P200 Features

Fingerprint Adds an additional layer of security to your files

■ Before entering Sleep mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in

Sleep mode. The computer or the module could be damaged.

■ Do not remove the battery pack while the computer is in Sleep mode.

Data in memory will be lost.

by requiring a valid fingerprint to access them.

TOSHIBA Value Added Package

This section describes the TOSHIBA Component features pre-installed on
the computer.

TOSHIBA Power
Saver

TOSHIBA Button
Support

TOSHIBA PC
Diagnostic Tool

TOSHIBA Flash Cards This utility supports the following functions,

TOSHIBA
Components
Common Driver

TOSHIBA
Accessibility

TOSHIBA Zooming
Utility

TOSHIBA Power Saver provides you with the
features of more various power supply
managements.

This utility controls the buttom operation of the
computer. The starting application from the
buttom can be changed.

The TOSHIBA PC Diagnostic Tool will display
basic system configuration information and allow
the functionality of some of the computer’s builtin
hardware devices to be tested.

■ Hot key function

■ TOSHIBA utility launcher function

TOSHIBA Components Common Driver contains
the module required for the utility which TOSHIBA
offers.

The TOSHIBA Accessibility utility provides
support to movement impaired users when they
need to use the TOSHIBA Hot-key functions. In
use, the utility allows you to make the Fn key
‘sticky’, that is you can press it once, release it,
and they press one of the "F" keys in order to
access its specific function. When set, the Fn key
will remain active until another key is pressed.

This utility allows you to enlarge or reduce the
icon size on Windows Desktop or the zoom factor
associated with specific supported applications.

User’s Manual 1-10

P200 Features

Utilities

and Applications

This section describes preinstalled utilities and tells how to start them. For
details on operations, refer to each utility’s online manual, help files or
readme.txt files.

TOSHIBA Assist TOSHIBA Assist is a graphical user interface that

provides easy access to help and services.

DVD Video Player The DVD player is used to play DVD Video media

through an on-screen interface and functions.

TOSHIBA ConfigFree ConfigFree is a suite of utilities to allow easy

TOSHIBA Disc
Creator

TOSHIBA DVD-RAM
Utility

TOSHIBA Hardware
Setup

CD/DVD Drive
Acoustic Silencer

Ulead DVD
MovieFactory
TOSHIBA

®

for

control of communication devices and network
connections. ConfigFree also allows you to find
communication problems and create profiles for
easy switching between location and
communication networks.

To start ConfigFree, click the Start Button, point to
All Programs, point to TOSHIBA, point to
Networking and click ConfigFree.

You can create discs in several formats including
audio CDs that can be played on a standard
stereo CD player and data discs to store the files
and folders on your hard disk drive. This software
can be used on a model with a CD-RW/
DVD-ROM drive or a DVD Super Multi drive.

TOSHIBA DVD-RAM Utility has the function of
Physical Format and Write-Protect to DVD-RAM.
This utility is contained in the setup module of
TOSHIBA Disc Creator. You can start TOSHIBA
DVD-RAM Utility from the menu bar as follows.
Start  All Programs  TOSHIBA  CD&DVD
Applications  DVD-RAM Utility.

This program lets you customize your hardware
settings according to the way you work with your
computer and the peripherals you use. To access
this utility, click the Start Button, point to All
Programs, point to TOSHIBA, point to Utilities,
point to HWsetup.

This utility allows you to configure the read speed
of CD drive. You can either configure Normal
Mode, which operates the drive at its maximum
speed for quick data access, or Quiet Mode,
which runs at single speed for CD audio and
which can lessen operational noise. It is
ineffective in DVD.

You can edit digital video and make a DVD-Video
and support Label Flash function.

User’s Manual 1-11

P200 Features

The availability of Label Flash function depends on the model you
purchased.

FingerPrint utility This product has a fingerprint utility installed for

the purpose of enrolling and recognizing
fingerprints. (depending on the model purchased.)
By enrolling the ID and password to the fingerprint
authentication device, it is no longer necessary to
input the password from the keyboard. Just by
swiping the finger against the fingerprint sensor,
the following functions will be enabled:

■ Logon to Windows and access a security-

enabled homepage through IE (Internet
Explorer).

■ Files and folders can be encrypted/decrypted

and third party access to them prevented.

■ Disable the password-protected screen-saver

when returning from power-saving (Sleep)
mode.

■ System boot authentication and Single Touch

Boot feature.

■ Power on Security and Single Sign On

feature.

Fingerprint cannot be used in models that do not have a fingerprint module
installed.

Windows Mobility
Center

Mobility Center is a utility for accessing several
mobile PC settings quickly in one window. A
default maximum of eight tiles are provided by the
operating system, and the additional two titles are
added to your Mobility Center

■ Lock Computer:

This can be used to lock your computer
without turning it off. This has the same
function as the Lock button at the bottom of
the right pane in the start menu.

■ TOSHIBA Assist:

This can be used to open TOSHIBA Assist if
it is already installed in your computer.

User’s Manual 1-12

Options

P200 Features

You can add a number of options to make your computer even more
powerful and convenient to use. The following options are available:

Memory Modules Two memory module can be installed in this

computer.

Use only PC4200 and PC5300* compatible DDRII memory modules. See
your TOSHIBA dealer for details.

* The availability of DDRII is dependent on the model you purchased.

Battery Pack An additional battery pack can be purchased from

your TOSHIBA dealer. Use it as a spare to
increase your computer operating time.

High capacity battery
pack

AC adapter If you use your computer at more than one site

USB Floppy Disk
Drive

An additional battery pack can be purchased from
your TOSHIBA dealer. Use it as a spare to
increase your computer operating time.

frequently, it may be convenient to purchase an
additional AC adapter for each site so you will not
have to carry the adapter with you.

Lets you attach a floppy disk drive to your
computer by means of a USB cable.

User’s Manual 1-13

The Grand Tour

1. Front Edge Logo*

2. DC IN LED

3. Power LED

4. Battery LED

5. Hard Disk Drive LED

6. Multiple Digital Media Card Slot
Access LED*

7. Wireless Communication Switch
and LED*

8. Microphone Jack

9. Headphone Jack

10. Volume Control

11. Multiple Digital Media Card Slot*

9210

3 4

1187

5 61

This chapter identifies the various components of your computer. Become
familiar with each component before you operate the computer.

Certain types of notebook chassis are designed to accommodate all
possible configurations for an entire product series. Your selected model
may not have all the features and specifications corresponding to all of the
icons or switches shown on the notebook chassis, unless you have
selected all those features.

Front with the display closed

The following figure shows the computer front with its display panel in the
closed position.

The Grand Tour

Chapter 2

* The availability of this feature is dependent on the model you purchased.

User’s Manual 2-1

Front of the computer with display closed

The Grand Tour

Front Edge Logo* Front Edge Logo indicates the computer series

you bought.
(The avaliability of this function is dependent on

the model you purchased.)

DC IN LED The DC IN LED indicates the computer is

connected to the AC adapter and it is plugged into
an AC power source.

Power LED In normal operating mode, the Power LED is blue

(depending on the model you purchased). If the
system is in SleepSleep Mode the LED will flash
amber, while the LED will be off when the
computer is turned off or is in Hibernation Mode.

Battery LED The Battery LED indicates the battery's current

charge/discharge status. It lights blue (depending
on the model you purchased) when the battery is
fully charged. It lights amber while the battery is
being charged from the AC adapter. It flashes
amber when the battery capacity is low.

Hard Disk Drive LED The Hard Disk Drive LED indicates that the hard

disk drive is being accessed. Every time your
computer runs a program, opens a file, or
performs some other function in which it must
access the hard disk drive, this light will go on.

Multiple Digital Media
Card Slot Access
LED*

The Multiple Digital Media Card Slot Access LED
lights up when the Multiple Digital Media Card is
accessed.

(The avaliability of this function is dependent on
the model you purchased.)

Wireless
Communication
Switch and LED*

The wireless communication switch turns on the
wireless networking transceiver. The Wireless
Communication LED beside it indicates that
wireless networking is turned on. Indicates
whether the Wireless devices is active or not.

(The avaliability of this function is dependent on
the model you purchased.)

Microphone Jack The standard 3.5 mm mini microphone jack

enables connection of a three conductive type
mini-jack for a monaural microphone.

Headphone Jack The headphone jack lets you connect stereo

headphones or other audio-output devices such
as external speakers. Connecting headphones or
other devices to this jack automatically disables
the internal speakers.

Volume Control Use this dial to adjust the volume of the stereo

speakers or headphones.

User’s Manual 2-2

The Grand Tour

1. Universal Serial Bus (USB) Port

2. Modem Jack

3. Optical Disc Drive and LED

4Fan Vents
5 Security Lock

1 2 3 4 5

Right side

Multiple Digital Media
Card Slot*

The Multiple Digital Media Card Slot allows you to
use media cards from digital still cameras and
various forms of portable information equipment.

(The availability of this function depends on the
model you purchased.)

The following figure shows the computer's right side.

The right side of the computer

Universal Serial Bus
(USB) Port

The Universal Serial Bus (USB 2.0 and 1.1
compatible) port enables USB-equipped devices
such as keyboards, mice, hard drives, scanners,
and printers to be connected to the computer.

Modem Jack In regions where an internal modem is installed

as standard equipment, this jack lets you use a
modular cable to connect the modem directly to a
telephone line.

Optical Disc Drive and
LED

The computer is configured with a full-size optical
disc drive module that lets you run either 12 cm
(4.72") or 8 cm (3.15") discs without using an
adapter. See the Drives section in this chapter for
technical specifications on each drive and
Chapter 4, Operating Basics, for information on
using the drive and caring for discs.The LED lets
you know when the Optical Disc Drive is being
accessed.

Fan Vents The fan vents help prevent the CPU from

overheating.

To prevent possible over heating of the CPU, never block the fan vents.

User’s Manual 2-3

The Grand Tour

1. DC IN 19V Jack

2. RGB Monitor Port

3. Fan Vents

4. Lan Jack

5. Universal Serial Bus (USB) Port

6. TV Out Port
7 i.LINK (IEEE1394a) Port*
8 Express Card Slot

1 3 4 5 62 7 8

Left side

Security Lock An optional security cable attaches to this port in

order to anchor your computer to a desk or other
large object to deter theft.

The following figure shows the computer's left side.

* The availability of this feature is dependent on the model you purchased.

The left side of the computer

DC IN 19V Jack The DC IN jack is where you plug in the AC

adapter.

RGB Monitor Port This 15-pin port lets you connect an external

video display to the computer.

Fan Vents The fan vents help prevent the CPU from

overheating.

To prevent possible over heating of the CPU, never block the fan vents.

LAN Jack This jack lets you connect to a LAN. The adapter

has built-in support for Ethernet LAN (10
megabits per second, 10BASE-T), Fast Ethernet
LAN (100 megabits per second, 100BASE-TX)
and Gigabit Ethernet LAN (1000 megabits per
second, 1000BASE-T). Two indicators built into
the jack let you see the LAN status.

Universal Serial Bus
(USB) Port

The Universal Serial Bus (USB 2.0 and 1.1
compatible) port enables USB-equipped devices
such as keyboards, mice, hard drives, scanners,
and printers to be connected to the computer.

TV Out Port Connect a 4-pin S- video cable into this connector

User’s Manual 2-4

in order to output either an NTSC or PAL
television signal.

The Grand Tour

1. Battery Pack

2. Fan Vent

3. Battery Pack Lock

4. Speaker

5. HDD1

6. HDD2*

7. Expansion Memory Socket

8. Fan Vent

9. Battery Pack Latch

1

3

9

8

4

2

7

6 5

Underside

The following figure shows the underside of the computer. Make sure the
display is closed before turning over your computer.

i.LINK (IEEE1394a)
Port

This port allows you to connect an external
device, such as a digital video camera, for high­speed data transfer.

Express Card Slot This slot allows you to insert an Express Card. An

Express Card module is a small, modular add-in
card technology based on PCI Express and
Universal Serial Bus (USB) interface. The max.
transmission rate at 2.5Gbps. Both 34mn type
and 54mm type are supported.

* The availability of this feature is dependent on the model you purchased.

The bottom of the computer

User’s Manual 2-5

The Grand Tour

Battery Pack The battery pack powers the computer when the

AC adapter is not connected. For detailed
information on the battery pack, refer to
Chapter 6, Power and Power-Up Modes.

Fan Vent The fan vents help prevent the CPU from

overheating.

Battery Pack Lock When you slide this into its locked position, the

battery pack cannot be released even if you
attempt to slide the battery pack latch into its open
position.

Speaker A third speaker to indicate bios beeps.
HDD1 Hard Disk Drives store data, files and programs.
HDD2* Hard Disk Drives store data, files and programs.

(The availability of this function depends on the
model you purchased.)

Expansion Memory
Socket

Use this socket to install a memory module to
increase your computer's memory. Refer to the

Memory expansion section in Chapter 8, Optional
Devices.

To prevent possible overheating of the CPU, never block the fan vents.

Battery Pack Latch With the Battery Pack Lock in its unlocked

position, you can slide this latch in order to
remove the battery pack.

User’s Manual 2-6

Front with the display open

1. Display Screen

2. Left and Right Speakers

3. TouchPad/Dual Mode Pad

4. TouchPad Control Buttons

5. Power Button

6. Internet Button*

7. CD/DVD Button*

8. Play/Pause Button*

9. Stop*

10. Previous Button*

11. Next Button*

12. Number Pad

13. Finger Print Scanner*

14. Web Camera*

15. Microphone*

1

12

13

3

4

14

11

2

5

6

7

8

9

10

15

The following figure shows the front of the computer with the display open.
To open the display, push the latch on the front of the display and lift it up.
Position the display at a comfortable viewing angle.

The Grand Tour

* The availability of this feature is dependent on the model you purchased.

The front with the display open

Display Screen The LCD displays high-contrast text and graphics

Appendix B - Display Modes for further
information. When the computer operates from
the AC adapter, the display screen's image will be
somewhat brighter than when it operates on
battery power - this is normal and is designed to
conserve battery power.

at a resolution up to 1680 × 1050 pixels. Refer to

To prolong the life of your display screen, use a screen saver when you're
not using the computer and it is idle.

User’s Manual 2-7

Left and Right
Speakers

The computer provides two speakers for stereo
sound reproduction.

The Grand Tour

TouchPad/Dual Mode
Pad

The TouchPad/Dual Mode Pad pointing device is
located in the centre of the palm rest and is used
to control the on-screen pointer. Refer to the How

the Swipe the Finger section in Chapter 4,
Operating Basics.

TouchPad Control
Buttons

Control buttons below the TouchPad/Dual Mode
Pad let you select menu items or manipulate text
and graphics designated by the on-screen
pointer.

Power Button Press the power button to turn the computer's

power on and off. There is an LED inside the
power button which shines in blue (depending on
the model you purchased) when the system is on.

Internet Button* Press this button to launch an Internet browser.If

the computer’s power is off, you can press this
button to turn on the computer’s power and
launch the browser automatically in one step.

(The availability of this function depends on the
model you purchased.)

CD/DVD Button* Pressing this button will launch an application

program that allows for watching CD/DVD.
An application that is launched differs by a model:
Windows Media Player/DVD Video Player.
(The availability of this function depends on the

model you purchased.)

Play/Pause Button* Press this button to begin playing an audio CD, a

DVD movie or digital audio files. This button also
acts as a Pause button.

(The availability of this function depends on the
model you purchased.)

Stop* Stops playing the CD, DVD or digital audio.

(The availability of this function depends on the
model you purchased.)

Previous Button* Skips backwards to the previous track, chapter or

digital file. Refer to Chapter 4, Operating Basics,
for details.

(The availability of this function depends on the
model you purchased.)

Next Button* Skips forward to the next track, chapter or digital

file. Refer to Chapter 4, Operating Basics, for
details.

(The availability of this function depends on the
model you purchased.)

User’s Manual 2-8

The Grand Tour

Numeric

Mode

Caps Lock

If Random or Shuffle is selected in Windows® Media Player, selecting Next
or Previous advances to a random selection.

Number Pad Press the Number Lock button to activate the

number pad. Use the number pad instead of the
number buttons on the keyboard to enter
numbers and ASCII codes.

Finger Print Scanner* Use the fingerprint scanner to prevent

unauthorised access to the laptop. Refer to the

Using the FingerPrint (FingerPrint sensor is
provided with some models) section in Chapter 4,
Operating Basics.

(The availability of this function depends on the
model you purchased.)

Web Camera* Take your picture or send your image to web

contacts.
(The availability of this function depends on the

model you purchased.)

Microphone* The Microphone is used with the Web Camera to

talk to other Web Camera users and to record
messages on windows media.

(The availability of this function depends on the
model you purchased.)

Keyboard Indicators

Numeric Mode You can use the keypad overlay (light gray

Caps Lock The Caps Lock LED lights when you press the

User’s Manual 2-9

labeled keys) for numeric input when the Numeric
mode icon lights blue.

Caps Lock key. When this light is on, pressing a
letter key on the keyboard produces an
uppercase (capital) letter.

Optical Disc drive

The computer will either have a CD-RW/DVD-ROM drive, or a single layer
or dual layer DVD Super Multi drive supporting ±R Double Layer depending
on its configuration. An ATAPI interface controller is used for the operation
of these optical drives. When the computer is accessing a disc, an indicator
on the drive glows.

Region codes for DVD drives and media

The disc drive and its media are manufactured according to the
specifications of six marketing regions. When you purchase DVD-Video,
make sure it matches your drive, otherwise it will not play properly.

Code Region
1 Canada, United States
2 Japan, Europe, South Africa, Middle East
3 Southeast Asia, East Asia
4 Australia, New Zealand, Pacific Islands, Central America,

South America, Caribbean

5 Russia, Indian Subcontinent, Africa, North Korea, Mongolia
6 China

The Grand Tour

Writable discs

This section describes the types of writable discs. Check the specifications
for your drive to for the type of discs it can write. Use TOSHIBA Disc
Creator to write compact discs. Refer to Chapter 4, Operating Basics.

CDs

■ CD-R discs can be written only once. The recorded data cannot be

erased or changed.

■ CD-RW discs can be recorded more than once. Use either 1x, 2x, or 4x

multi-speed CD-RW discs or high-speed 4x to 10x discs. The write
speed of ultra-speed CD-RW discs is a maximum of 24x speed.

DVDs

■ DVD-R and DVD+R discs can be written only once. The recorded data

cannot be erased or changed.

■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than

once.

User’s Manual 2-10

CD-RW/DVD-ROM drive

The full-size CD-RW/DVD-ROM drive module lets you record data to
rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") discs
without using an adapter.

The read speed is slower at the centre of a disc and faster at the other
edge.

DVD read 8 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 24 speed (maximum, ultra-speed media)

DVD Super Multi drive supporting ±R Double Layer

The full-size DVD Super Multi drive supporting ±R Double Layer module
lets you record data to rewritable discs as well as run either 12cm (4.72") or
8cm (3.15") discs without using an adapter.

The read speed is slower at the centre of a disc and faster at the other
edge.

DVD read 8 speed (maximum)
DVD-R write 8 speed (maximum)
DVD-RW write 6 speed (maximum)
DVD+R write 8 speed (maximum)
DVD+RW write 8 speed (maximum)
DVD-RAM write 5 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 16 speed (maximum, ultra-speed media)
DVD+R (DL) write 4 speed (maximum)
DVD-R(DL) write 4 speed (maximum)

The Grand Tour

This drive cannot use discs that allow writing faster than 8x speed or faster
(DVD-R and DVD+R with Single Layer), 6x speed or faster (DVD-RW), 8x
speed or faster (DVD+RW), 5x speed (DVD-RAM) or ultra-speed or faster
(CD-RW).

User’s Manual 2-11

AC adapter

The AC adapter converts AC power to DC power and reduces the voltage
supplied to the computer. It can automatically adjust to any voltage from
100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to
use the computer in almost any country/region.

To recharge the battery, simply connect the AC adapter to a power source
and the computer. See Chapter 6, Power and Power-Up Modes, for details.

The AC adapter

Use of the wrong adapter could damage your computer. TOSHIBA
assumes no liability for any damage in such case. The output rating for the
computer is 19 volts DC.

The Grand Tour

Please use only the AC Adapter supplied with the computer or an AC
adapter certified by TOSHIBA.

User’s Manual 2-12

Getting Started

This chapter provides basic information to get you started using your
computer. It covers the following topics:

Be sure also to read Instruction Manual for Safety & Comfort. This guide,
which is included with the computer, explains product liability.

■ Connecting the AC adapter

■ Opening the display

■ Turning on the power

■ Starting up for the first time

■ Turning off the power

■ Restarting the computer

■ Restoring the pre-installed software from the Product Recovery media.

Getting Started

Chapter 3

All users should be sure to carefully read the section Starting up for the first

time, which describes the actions to take when you turn on the power for

the first time.

Connecting the AC adapter

Attach the AC adapter when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power. The AC adapter can be connected to any power source
supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the
AC adapter to charge the battery pack, refer to Chapter 6, Power and

Power-Up Modes.

Use of the wrong adapter could damage your computer. TOSHIBA
assumes no liability for any damage in such case. The output rating for the
computer is 19 volts DC.

User’s Manual 3-1

Getting Started

1. Connect the power cord to the AC adapter.

Connecting the power cord to the AC adapter

2. Connect the DC output plug on the AC adapter to the DC IN input port
on the back of the computer.

Connecting the adapter to the computer

3. Plug the power cord into a live wall outlet. The Battery and DC IN
indicators on the front of the computer should glow.

To disconnect AC adaptor, you can follow the reversed procedure of
Connecting AC adaptor. Please hold the DC output plug portion by your
fingers and then plug it out when you disconnect the DC output plug.

User’s Manual 3-2

Opening the display

The display panel can be rotated in a wide range of angles for optimal
viewing.

1. Push the display latch on the front of the computer.

2. Lift the panel up and adjust it to the best viewing angle for you.

Use reasonable care when opening and closing the display panel. Opening
it vigorously or slamming it shut could damage the computer.

Turning on the power

This section describes how to turn on the power.

After you turn on the power for the first time, do not turn it off until you have
set up the operating system. Refer to the section Starting up for the first

time in this chapter.

Getting Started

Opening the display

1. If a USB floppy disk drive is connected, make sure the drive is empty - if a
disk is in the drive, press the eject button to remove it.

2. Open the display panel.

3. Press the computer's power button and then release it.

Turning on the power

User’s Manual 3-3

Starting up for the first time

When you first turn on the power, the computer's initial screen is the
Windows
each screen. During setup, you can click the Back button to return to the
previous screen.

Be sure to read the Windows
Agreement carefully.

®

Vista Startup Screen Logo. Follow the on-screen directions for

Turning off the power

The power can be turned off in one of three modes, either Shutdown (Boot)
Mode, Hibernation Mode or Sleep Mode.

Shut Down mode (Boot mode)

When you turn off the power in Shut Down mode no data will be saved and
the computer will boot to the operating system's main screen the next time
it is turned on.

1. If you have entered data, either save it to the hard disk, drive or to other
storage media.

2. Make sure all disk/disks activity has stopped before removing the
CD/DVD or floppy diskette.

■ Make sure the Hard Disk Drive indicators is off. If you turn off the

power while a disk (disks) is being accessed, you can lose data or
damage the disk.

■ Never turn off the power while an application is running. Doing so could

cause loss data.

■ Never turn off the power, disconnect an external storage device or

remove storage media during data read/write. Doing so can cause data
loss.

Getting Started

®

Operating System End User License

3. Click Start then click the arrow button ( ) located in the power
management buttons ( ) and select Shut Down from the
menu.

4. Turn off any peripheral devices connected to your computer.

Do not turn the computer or peripheral devices back on immediately - wait
a short period to avoid and peripheral damage.

User’s Manual 3-4

Sleep Mode

If you do have to interrupt your work, you are able to turn off the power
without exiting from your software by placing the computer into Sleep
Mode. In this mode data is maintained in the computer’s main memory so
that, when you turn on the power again, you can continue working right
where you left off.

■ When the AC adaptor is connected, the computer will go into Sleep

Mode according to the settings in the Power Options.

■ To restore the operation from the computer from Sleep Mode, press the

power button or press any key. Please be aware that this latter action
only works on the internal keyboard if the. Wake-up on Keyboard
option is enabled within the HW Setup utility.

■ If the computer enters Sleep Mode while a network application is

active, the application might not be restored when the computer is next
turned on and the system returns from Sleep Mode.

■ To prevent the computer from automatically entering Sleep Mode,

disable Sleep Mode within the Power Options. However, please be
aware that this configuration will nullify the computer’s Energy Star
compliance.

■ Before entering Sleep Mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in

Sleep Mode. The Computer or the module could be damaged.

■ Do not remove the battery pack while the computer is in Sleep Mode

(unless the computer is connected to an AC power source). Data in
memory will be lost.

Getting Started

Benefits of Sleep Mode

The Sleep Mode feature provides the following benefits:

■ Restore the previous working enviroment more rapidly than does the

Hibernation Mode feature.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System
Sleep Mode feature.

■ Allows the use of the panel power off feature.

User’s Manual 3-5

Getting Started

Executing Sleep Mode

You can enter also Sleep Mode by pressing Fn + F3 - please refer to
Chapter 5, The Keyboard, for further details.

Youu can enter Sleep Mode in one of three ways:

1. Click Start then click the sleep button ( ) located in the power
management buttons ( ), or click the arrow button ( )
and select Sleep from the menu.

2. Close the computer’s LCD display panel. Please note that this feature
must be enabled - please refer to the Power Options (to access it, click

Start followed by Control Panel followed by System and
Maintenance and then click the Power Options).

3. Press the power button. Please note that this feature must be
enabled - please refer to the Power Options (to access it, click Start
followed by Control Panel followed by System and Maintenance and
then click the Power Options and point to Choose what the power
button do).

When you turn the power back on, you can continue where you left when
you shutdown the computer.

■ When the computer is in Sleep Mode, the power indicator will blink

orange.

■ If you are operating the computer on battery power, you can lengthen

the overall operating time by turning it off into Hibernation Mode - Sleep
Mode will consume more power while the computer is off.

Sleep Mode limitations

Sleep Mode will not function under the following conditions:

■ Power is turned back on immediately after shutting down.

■ Memory circuits are exposed to static electricity or electrical noise.

Hibernation mode

The Hibernation Mode feature saves the contents of memory to the hard
disk drive when the computer is turned off so that, the next time it is turned
on, the previous state is restored. Please note that the Hibernation Mode
feature does not save the status of any peripheral devices connected to the
computer.

■ Save your data. While entering Hibernation Mode, the computer saves

the contents of memory to the hard disk drive. However, for safety
sake, it is best to save your data manually.

■ Data will be lost if you remove the battery or disconnect the AC adaptor

before the save is completed. Wait for the Hard Disk Drive indicator to
go out.

■ Do not install or remove a memory module while the computer is in

Hibernation Mode. Data will be lost.

User’s Manual 3-6

Getting Started

Benefits of Hibernation Mode

The Hibernation Mode feature provides the following benefits:

■ Saves Data to the hard disk drive when the computer automatically

shutsdown because of a low battery condition.

■ You can return to your previous working environment immediately when

you turn on the computer.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System
Hibernate feature.

■ Allows the use of the panel power off feature.

Starting Hibernation Mode

You can also enable Hibernation Mode by pressing Fn + F4 - please refer
to Chapter 5, The Keyboard, for further details.

To enter Hibernation Mode, follow the steps below.

1. Click Start.

2. Click the arrow button ( ) in the power management buttons
().

3. Select Hibernate from the menu.

Automatic Hibernation Mode

The computer can be configured to enter Hibernate Mode automatically
when you press the power button or close the lid. In order to define these
settings, you can follow the steps as described below:

1. Click Start and click the Control Panel.

2. Click System and Maintenance and click Power Options.

3. Click Choose what the Power Button do or Choose what closing
the lid does.

4. Enable the desired Hibernation Mode settings for When I press the
power button or When I close the lid.

5. Click the Save Changes button.

Data save in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer takes a
moment to save the current data in memory to the hard disk drive. During
this time, the Hard Disk Drive indicator will glow.

After you turn off the computer, and the content of memory has been saved
to the hard disk drive, turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.

User’s Manual 3-7

Restarting the computer

Certain conditions require that you reset the computer, for example if:

■ You change certain computer settings.

■ An errors and the computer does not respond you your keyboard

commands.

If you need to restart the computer, there are three ways this can be
achieved:

1. Click Start then click the arrow button ( ) in the power management
buttons ( ) and select Restart from the menu.

2. Press Ctrl+Alt+Del to display the menu window, then select Restart
from the Shutdown options.

3. Press the power button and hold it down for five seconds. Once the
computer has turned itself off, wait between ten and fifteen seconds
before turning the power on again by pressing the power button.

System Recovery Options

About 1.5GB hidden partition is allocated on the hard disk drive for the
System Recovery Options.

The System Recovery Options feature will be unusable if this partition is
deleted.

The System Recovery Options feature is installed on the hard disk when
shipped from the factory. The System Recovery Options menu includes
some tools to repair startup problems, run diagnostics or restore the sys­tem. You can see the more information about "Startup Repair" in "Windows
Help and Support" content.

The System Recovery Options can also be run manually to repair
problems. The procedure is as follows. Follow the instructions shown on
the onscreen menu.

1.Turn off the computer.

2.While holding the F8 key, turn the computer on.

3.The Advanced Boot Options menu will be displayed. Use the arrow keys

to select Repair Your Computer and press Enter.

4.Follow the on-screen instructions.

Getting Started

The Windows Vista™ Complete PC Backup feature can be used on
Windows Vista™ Business Edition and Ultimate Edition.

User’s Manual 3-8

Getting Started

Restoring the preinstalled software from the Product Recovery disc

If preinstalled files are damaged, use the Product Recovery disc to restore
them. To restore the operating system and all preinstalled software, follow
the steps below.

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost. You can not use System Recovery
Options if restoring the pre-installed software without System Recovery
options.

1. Load the Product Recovery disc in the drive and turn off the computer's
power.

2. Switch on the computer and, when the In Touch with Tomorrow
TOSHIBA prompt appears, press the F12 key to display the Boot Menu.

3. Use the cursor key to select the CD-ROM/DVD drive in the display
menu.

4. Follow the on-screen instructions.

5. If your computer came with additional software installed, this software
can not be recovered from the Product Recovery disk. Re-install these
applications (e.g. Works Suite, DVD Player, Games, etc.) separately
from other media.

User’s Manual 3-9

Operating Basics

1

2

1. TouchPad control buttons 2. TouchPad/Dual Mode Pad

This chapter gives information on basic operations including using the
TouchPad/Dual Mode Pad, optical disc drives, the internal modem, LAN
and wireless LAN. It also provides tips on caring for your computer and on
heat dispersal.

Using the TouchPad/Dual Mode Pad

To use the TouchPad/Dual Mode Pad, simply move your finger tip across it
in the direction you want the on-screen pointer to go.

Operating Basics

Chapter 4

TouchPad/Dual Mode Pad and control buttons

The two buttons below the TouchPad/Dual Mode Pad are used like the
buttons on a standard mouse.

Press the left button to select a menu item or to manipulate text or graphics
designated by the pointer. Press the right button to display a menu or other
function depending on the software you are using.

Do not press on the TouchPad/Dual Mode Pad too hard or press a sharp
object such as a ball point pen against it. The TouchPad/Dual Mode Pad
could be damaged.

User’s Manual 4-1

Operating Basics

Mail Button ConfigFree Windows Vista Photo Gallery

Switch Button

Volume

Application Buttons

The TouchPad/Dual Mode Pad has similar functions to a two-button mouse
with a scroll wheel. For some functions, you can tap it instead of pressing a
button.

You can customize pointing device actions in Mouse Properties. Open the
Control Panel, select the Mouse icon and press Enter to open the Mouse
Properties window.

Click: Click the left control button or tap the TouchPad/Dual

Mode Pad once.

Double-click: Click the left control button twice or tap the

TouchPad/Dual Mode Pad twice.

Scroll Vertical: Move your finger up or down the right edge of the

TouchPad/Dual Mode Pad.

Scroll Horizontal: Move your finger left or right along the bottom edge

of the TouchPad/Dual Mode Pad.

Dual Mode Pad Button function (Dual Mode Pad is provided with some models)

Dual Mode Pad Button

Switch button To switch between Cursor Mode and Button

Mode. When you switch to Button Mode, the pad
blinks blue.

Volum e Increases or decreases the volume of speaker

and headphone.

Mail button Starts your mail box for you to receive and send

mails.

User’s Manual 4-2

Operating Basics

1 2 3

Configfree Configfree is a suite of utilities to allow easy

Windows Vista Photo
Gallery

Application buttons Three application buttons have default setting.

Please refer to "Properties for synaptics Dual Mode Pad" for details.

control of communication devices and network
connections. It also allows you to find
communication problems and create profiles for
easy switching between locations and
communication networks.

Windows Vista Photo Gallery gives you many
tools for your digital photos and videos. You can
organize, find, and view your photos and videos,
as well as edit, print, and share them from within
Windows Vista Photo Gallery. It also makes it
easy to transfer your photos from your camera to
your computer, using a simple import process.

You can assign other functions and programs to
button 1 to 3.

Using the FingerPrint (FingerPrint sensor is provided with some models)

This product has a FingerPrint utility installed for the purpose of enrolling
and recognizing FingerPrints. By enrolling the ID and password to the
FingerPrint authentication device, it is no longer necessary to input the
password from the keyboard. Just by swiping the finger against the
FingerPrint sensor, the following functions will be enabled:

■ Logon to Windows and access a security-enabled homepage through

IE (Internet Explorer).

■ Files and folders can be encrypted/decrypted and third party access to

them prevented.

■ Disable the password-protected screen-saver when returning from

power-saving mode such as Sleep Mode.

■ Power-on Security and Single Sign-On feature.

To "swipe" refers to the action of reading a FingerPrint using the
FingerPrint sensor.

User’s Manual 4-3

How the Swipe the Finger

Using the following steps when swiping fingers for FingerPrint registration
or authentication will help to minimize authentication failures:

1. Align the first joint of the finger to the center of the sensor. Lightly touch
the sensor and swipe finger levelly towards you.

While lightly touching the sensor, swipe the finger towards you until the
sensor surface becomes visible.

Ensure the center of the FingerPrint is on the sensor when swiping the
finger.

■ Avoid swiping with the finger stiff or pressed-on too hard

FingerPrint reading may fail if the center of the FingerPrint is not
touching on the sensor, or when finger is swiped while pressing hard.
Make sure that the center of the FingerPrint is touching the sensor
before swiping.

■ Confirm the center of the FingerPrint whirl before swiping

The thumb's FingerPrint has a bigger whirl, which is prone to
misalignment and distortions. This will cause difficulty in registration
and a drop in the authentication success rate. Always confirm the
center of the FingerPrint whirl so that it is swiped along the centerline of
the sensor.

■ When FingerPrint reading is not successful

There is a possibility of authentication failures if the finger is swiped too
quickly or too slowly. Follow the onscreen instructions to adjust the
speed of the swipe.

Operating Basics

The following illustrations show the correct way to slide your finger over the
recognition sensor.

Align the finger and sensor like the drawings.

User’s Manual 4-4

Points to note about the FingerPrint Sensor

Please be aware of the following considerations when using the FingerPrint
sensor. A failure to follow these guidelines might result in damage to the
sensor, sensor failure, FingerPrint recognition problems or a lower
FingerPrint recognition success rate.

■ Do not scratch or poke the sensor with your nails or any hard or sharp

objects.

■ Do not press the sensor strongly.

■ Do not touch the sensor with a wet finger or any wet objects - keep

sensor surface dry and free of water vapor.

■ Do not touch the sensor with a soiled or dirty finger as minute foreign

particles of dust and dirt may scratch it.

■ Do not paste stickers or write on the sensor.

■ Do not touch the sensor with a finger or any other object which may

have a built-up of up static electricity on it.

Observe the following before you place your finger on the sensor whether
for FingerPrint enrollment/registration or recognition:

■ Wash and dry your hands thoroughly.

■ Remove static electricity from your fingers by touching any metal

surface. Static electricity is a common cause of sensor failures,
especially when the weather is dry.

■ Clean the sensor with a lint-free cloth - do not use detergent to any

other chemicals to clean the sensor.

■ Avoid the following finger conditions for enrollment or recognition as

they may result in FingerPrint enrollment errors or a drop in the
FingerPrint recognition success rate.

■ Soaked or swollen finger (e.g. after taking bath)

■ Injured finger

■ Wet finger

■ Soiled or oily finger

■ Extremely dry skin condition on finger

Observe the following to improve the FingerPrint recognition success rate:

■ Enroll two or more fingers.

■ Enroll additional fingers if recognition failure occurs when using already

enrolled fingers.

■ Check the condition of your finger - any conditions which have changed

since enrollment, such as injured, rough, extremely dry, wet, soiled,
dirty, oily, soaked, swollen fingers, may lower the recognition success
rate. Also if the FingerPrint is worn down or the finger becomes thinner
or fatter, the recognition success rate may be lowered.

■ As the FingerPrint for each finger is different and unique. you should

ensure that only the registered or enrolled FingerPrint or FingerPrints
are used for identification.

Operating Basics

User’s Manual 4-5

Operating Basics

■ Check the position and speed at which you swipe your finger across the

sensor - please refer to the preceding drawing.

How to Delete the FingerPrint Data:
Saved FingerPrint Data is stored in special non-volatile memory inside the

FingerPrint sensor. Therefore, if you give the computer to someone else, or
dispose of it in any way, the following process is recommended to delete
your FingerPrint information:

1. Click Start followed by All Programs, followed by Protector Suite QL
and then click Control Center.

2. The Protector Suite QL screen is displayed.

3. Click FingerPrint and click Delete.

4. Click Settings and click FingerPrint Storage Inspector.

5. The FingerPrint Storage Inspector screen will be displayed. If
FingerPrint data is displayed as part of the list, simply select all of this
information and then Remove.

6. Check whether all of the FingerPrint data was deleted on the
FingerPrint Storage Inspector screen.

In use, please be aware of the following limitations of the FingerPrint
sensor:

■ The FingerPrint sensor compares and analyzes the unique

characteristics in a FingerPrint.

■ A warning message will be displayed when recognition is abnormal or

recognition is not successful within a fixed duration.

■ The recognition success rate may differ from user to user.

■ Toshiba does not guarantee that this FingerPrint recognition

technology will be error-free.

■ Toshiba does not guarantee that the FingerPrint sensor will recognize

the enrolled user or accurately screen out unauthorized users at all
times. Toshiba is not liable for any failure or damage that might arise out
of the use of this FingerPrint recognition software or utility.

Points to note about the FingerPrint Utility software

You are able to backup saved FingerPrint data and information within the
PasswordBank by using the import or Export User Data facility under the
FingerPrint management software. However, please be aware that any
encrypted files cannot be backup within FileSafe using this function - in
these instances it is recommended that you backup these files to external
media using standard file copy processes.

The user should back up the user profile information when using the
functions provided in this software to encrypt files or folders. If this software
or the user information is deleted without backing up the user profile
information, the encrypted files will no longer be accessible. In addition, if
the backup data is not used, the user will not be identified as the same user
even if the same name is used again in user enrolment.

User’s Manual 4-6

Please refer to the following procedures to back up.
If Windows Vista™’s file encryption function EFS (Encryption File System)

is used to encrypt a file, the file cannot be further encrypted using the
encryption function of this software. In the help file, it is stated that this
software's Password Bank function can be used for the Internet and
general applications. However, the Internet Password Bank function in the
FingerPrint utility provided in this computer can only be used with IE
(Internet Explorer).

Set up Procedure

Please use the following procedure when first using FingerPrint
authentication.

FingerPrint Registration

You should initially enroll the required authentication data using the ‘User
Enrollment’ Wizard.

■ In use, the FingerPrint authentication system will use the same

username and password as defined within Windows operating system.
If no Windows password has been configured, you must do this before
starting the FingerPrint registration process.

■ Up to twenty-one FingerPrint patterns can be registered on this sensor.

1. Click Start followed by All Programs followed by Protector Suite QL
and then click User Enrollment.

You are also able to start the User Enrollment Wizard by using the
following method.

■ Click the Protector Suite QL icon in the Task Bar.

■ Swipe your finger across the FingerPrint Sensor.

Operating Basics

2. Click Next.

3. At the User’s Password screen which is then displayed, you should
ensure that the same Windows username is displayed before entering
the appropriate password into the Enter you password field. Once this
has been done, click Next.

4. At the Hints for FingerPrint Enrollment screen, confirm the message
displayed and ensure that there is a check mark in the Run Interactive
Tut ori al box. Once this has been done, click Next.

5. At the Correct swipe Procedure screen, confirm the message that is
diplayed and then click Next.

6. At the Scanning Practice screen, you are able to practice swiping your
finger to ensure you use the correct method. Once you have finished
practicing, click Next.

User’s Manual 4-7

7. At the User’s Fingers screen, select the finger you wish to enroll from
the illustration and then click Next. On this screen please be aware that
any previously enrolled FingerPrints would have green check marks,
while the FingerPrint you are about to enroll will have a red check mark.
If any of the previously enrolled FingerPrints is selected again, the latest
information will be enrolled and any previous information over-written.

8. At Advanced Security screen, select whether you wish tto enable the
security function, and then click Next.

9. At Finalization screen, click Finish - this will complete the FingerPrint
registration process.

Window Logon via FingerPrint Authentication

If required, you are also able to use FingerPrint authentication in place of
the usual Windows logon process using your username and password.
This method is specially useful where there are many users using the same
computer as it removes the need for actual user selection when the system
is started.

FingerPrint Authentication Procedure

1. Start up the computer.

2. At the Logon Authorization screen, choose any of the enrolled fingers
and swipe the FingerPrint on the sensor - If the authentication process
is successful, the user will automatically be logged into Windows.

Operating Basics

If the FingerPrint authentication process fails you will need to log into
Windows using the appropriate username and password. In addition, you
should use this manual login process if Finger Print authentication fails for
three consecutive tries - a warning message will be displayed when
authentication is not normal or is not successful within a fixed duration.

FingerPrint Power-on Security

General

The FingerPrint authentication system can be used to replace the keyboard
based password authentication system that is used when the computer is
turned on.

If you do not want to use the FingerPrint authentication system for
password authentication when the computer is turned on, but instead prefer
to use the keyboard entry method instead, simply press the BkSP
(backspace) key or the ESC/Rotation button when the FingerPrint Power­on Security screen is displayed. Using this process will switch the
password input screen across to the keyboard based entry screen.

User’s Manual 4-8

Operating Basics

■ You must ensure that you use the TOSHIBA Password Utility to

register a User Password before using the FingerPrint Power-on
Security and its extended function to allow FingerPrint to be used to
access the computer when it is turned on.

■ If the FingerPrint authentication process fails five times, a preset time

limit is exceeded, or you press the BkSP (backspace) key, [Password=]
will be displayed on the screen and you will have to enter either the
User Password or Supervosor Password manually in order to start the
computer.

■ When swipe your finger, please ensure you do it slowly and at a

constant speed. If you find that this does not improve the authentication
rate, you should try to adjust the speed at which the finger is swiped.

■ If there are any changes in the environment or setting related to

authorization, you will be required to provide authorization information
such as a User Password (and, if applicable, the HDD (Hard Disk
Drive) password).

How to Enable FingerPrint Power-on Security Settings

It is necessary to first enroll your FingerPrint with the Protector Suite QL
application prior to enabling and configuring the FingerPrint Power-on
Security System. You should check that your FingerPrint is enrolled before
configuring the settings (please refer to the Manual for FingerPrint
Registration/Enrollment for further instructions.)

1. Swipe your finger across the FingerPrint Sensor.

2. MENU will appear in the lower right corner of the screen. Swipe(*) your
finger on the FingerPrint sensor and then select Control Center from the
items presented in this menu

* It is recommended that the keyboard cursor keys (movement) and enter

key (selection) or the directional pad be used when selecting and item
from the Menu in laptop or landscape modes.

3. At the FingerPrint Software Management screen, click Settings and
then click Power-on Security.

4. At the Power Security screen, place a check mark in the Replace the
power-on and hard disk drive passwords with the FingerPrint reader
setting and then click OK.

User’s Manual 4-9

FingerPrint Single Sign-On Feature

General

This is a feature that allows the user to complete the authentication for both
the User/BIOS Password (and, if applicable, the HDD (Hard Disk Drive)
Password) and logging onto Windows using only one FingerPrint
authentication when booting up. It is necessary to register the User/BIOS
Password and Windows Logon password before using the FingerPrint
Power-on Security and this FingerPrint Single Sign On Feature. Please use
TOSHIBA Password Utility to register your User/BIOS Password. If
Windows Logon is not the default for your system, see Manual to register
your Windows Logon password.

Only one FingerPrint authentication is required to replace the User/BIOS
Password (and, if applicable, the HDD (Hard Disk Drive) Password) and
Windows Logon Password.

How to Enable FingerPrint Single Sign-On Feature

It is necessary to first enroll your FingerPrint with the Protector Suite QL
application prior to enabling and configuring the FingerPrint Single Sign-
On Feature. You should check that your FingerPrint is enrolled before
configuring the settings (please refer to the Manual for FingerPrint
Registration/Enrollment for furthe instructions).

1. Swipe your finger across the FingerPrint Sensor.

2. MENU will appear in the lower right corner of the screen. Swipe(*) your
finger on the FingerPrint Sensor and select Control Center from the
items presented in this menu.

* It is recommended that the keyboard cursor keys (movement) and enter

key (selection) or the directional pad be used when selecting and item
from the Menu in laptop or landscape modes.

3. At the FingerPrint Software Management screen, click Settings and
then click Power-on Security.

4. At the Power Security screen, place a check mark in the Replace the
power-on and hard disk drive passwords with the FingerPrint reader

setting and then click OK.

Operating Basics

FingerPrint utility limitations

TOSHIBA does not guarantee that the FingerPrint utility technology will be
completely secure or error-free or it will be accurately screen out
unauthorized users at all times. TOSHIBA is not liable for any failure or
damage that might arise out of the use of the FingerPrint software.

User’s Manual 4-10

Using the Web Camera

1. Active LED 2. Web Camera Lens

21

This section describes the bundled Web Camera utility, which can capture
still and video images. The Web Camera will auto-run when Windows
starts.

Operating Basics

User’s Manual 4-11

Using the software

2

1

3

4

6

8

7

5

1. Capture still images

2. Video Recording

3. Audio Recording

4. Function

5. Display Window

6. Camera Resolution

7. Mute

8. Effects

The Web Camera software is pre-configured to start when you turn on
Windows Vista; if you need to restart it go to Start  Programs  Camera
Assistant Software  Camera Assistant Software.

Operating Basics

Capture Still Images Click to see a preview of the captured image; you

can also e-mail the image.

Video Recording Click to start recording, click again to stop

recording and see a preview of the video.

Audio Recording Click to start recording, click again to stop and

listen to a preview of the audio.

Function Access additional functions: About, Player,

Effects, Properties, Settings and Help.

About Displays software manufacturer details.
Player Play video files.
Effects Choose images to be displayed on the capture

screen.

Properties Choose from the Options tab to flip, zoom, flicker

rate, night mode and backlight compensation; in
the Image tab change the colour settings; in the
profile tab change the lighting conditions.

User’s Manual 4-12

Operating Basics

Settings Choose from the: Options tab to change the tool

Help Displays the help files for the software.

Using the internal modem

This section describes how to setup the modem and use it to connect to
other computer systems. Refer to the computer's online help files and the
online help files for your modem software, for more information.

The internal modem does not support the voice functions described in the
help files. All data and fax functions are supported.

■ In case of a lightning storm, unplug the modem cable from the

telephone jack.

■ Do not connect the modem to a digital telephone line. A digital line will

damage the modem.

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:

1. Do not use this product near water, for example, near a bathtub, wash
bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.

2. Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord indicated in this manual.

position; the Picture tab to select picture output
options such as size, export file and saving
location; the Video tab to choose output settings
such as Frame Rate, Size, Compression and the
file save path; the Audio tab to chnage the Audio
Device, Compression, Volume and file save path.

User’s Manual 4-13

Region selection

Telecommunication regulations vary from one country/region to another, so
you will need to make sure the internal modem's settings are correct for the
country/region in which it will be used.

1. Open the Modem Region Select application. It is located on the
Programs menu at TOSHIBA  Networking  Modem Region Select.

Do not use the Country/Region Select function in the Modem setup utility
in the Control Panel if the function is available. If you change the
Country/Region in the Control Panel, the change may not take effect.

2. The Region Selection icon appears on the Windows Task Bar.

The Region Selection icon

3. Click the icon with the primary mouse button to display a list of regions
that the modem supports. A sub menu for telephony location
information will also be displayed. A check will appear next to the
currently selected region and telephony location.

4. Select a region from the region menu or a telephony location from the
submenu.

■ When you click a region it becomes the modem's region selection,

and the New Location for telephony will be set automatically.

■ When you select a telephony location, the corresponding region is

automatically selected and it becomes the modem's current region
setting.

Operating Basics

Properties menu

Click the icon with the secondary mouse button to display the following
menu.

The properties menu

User’s Manual 4-14

Settings

You can enable or disable the following settings:

AutoRun Mode

Region Select Utility starts automatically when you start up the operating
system.

Open the Dialling Properties dialogue box after selecting
region.

The dialling properties dialogue box will be displayed automatically after
you select the region.

Location list for region selection.

A submenu appears displaying location information for telephony.

Open dialogue box, if the modem and Telephony Current
Location region code do not match.

A warning dialogue box is displayed if current settings for region code and
telephony location are incorrect.

Modem Selection

If the computer cannot recognize the internal modem, a dialogue box is
displayed. Select the COM port for your modem to use.

Operating Basics

Dialing Properties

Select this item to display the dialling properties.

If you are using the computer in Japan, technical regulations described in
the Telecommunications Business Law require that you select Japan
region mode. It is illegal to use the modem in Japan with any other
selection.

Connecting

To connect the internal modem cable, follow the steps below.

■ In case of a lightning storm, unplug the modem cable from the

telephone jack.

■ Do not connect the modem to a digital telephone line. A digital line will

damage the modem.

User’s Manual 4-15

1. Plug one end of the modular cable into the modem jack.

2. Plug the other end of the modular cable into a telephone jack

Connecting the internal modem

Do not pull on the cable or move the computer while the cable is
connected.

If you find that the modem speed is low or communication is interrupted
when you are using the modem, please set the CPU speed to Maximum
within the TOSHIBA Power Saver utility.

Disconnecting

To disconnect the internal modem cable, follow the steps below.

1. Pinch the lever on the connector in the telephone jack and pull out the
connector.

2. Disconnect the cable from the computer in the same manner.

Operating Basics

LAN

The computer is equipped with networking hardware that supports Ethernet
LAN (10megabits per second, 10BASE-T), Fast Ethernet LAN (100
megabits per second and Gigabit Ethernet LAN (1000BASE-T).

Do not install or remove an optional memory module while the Wake-up on
LAN feature is enabled.

The Wake-up on LAN feature does not work on battery power, you should
always leave the computer connected to the AC adapter if you are using
this feature.

Connecting the LAN cable

The computer must be configured properly before connecting to a LAN.
Logging onto a LAN using the computer's default settings could cause a
malfunction in LAN operation. Check with your LAN administrator
regarding set-up procedures.

User’s Manual 4-16

If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you
can connect using either a CAT5 or a CAT3 cable.

If you are using 100BASE-TX Fast Ethernet or 1000BASE-T Gigabit
Ethernet, you must connect using a CAT5 cable.

To connect the LAN cable, follow the steps below.

1. Turn off the power to the computer and to all external devices
connected to the computer.

2. Plug one end of the cable into the LAN jack. Press gently until you hear
the latch click into place.

Connecting the LAN cable

3. Plug the other end of the cable into a LAN hub connector. Check with
your LAN administrator before connecting to a hub.

Disconnecting the LAN cable

To disconnect the LAN cable, follow the steps below.

1. Pinch the lever on the connector in the computer's LAN jack and pull
out the connector.

2. Disconnect the cable from the LAN hub in the same manner. Check with
your LAN administrator before disconnecting from the hub.

Operating Basics

Wireless LAN

The wireless LAN is compatible with other LAN systems that comply with
the IEEE802.11a, 11b, 11g and Draft 11n wireless LAN standards.

It supports the following:

■ Automatic Transmit Rate Select mechanism in the transmit range of 54,

48, 36, 24, 18, 9, 6 Mbps for 802.11a/b/g and 802.11b/g wireless LAN
module.

■ Advanced Encryption Standard (AES) data encryption, based on 256bit

encryption algorithm.

Wake-up on LAN does not function on a Wireless LAN.

■ Frequency Channel Selection (5GHz and 2.4 GHz)

■ Roaming over multiple channels

■ Card Power Management

■ Wi-Fi Protected Access (WPA) data encryption

User’s Manual 4-17

11a, 11b, 11g and 11n wireless are based on IEEE 802.11a, 802.11b,

802.11g and 802.11n respectively. The IEEE 802.11n specification has not
been finalized and is currently in draft release. The TOSHIBA 11a/b/g/n
Wireless LAN Adapters are based on the Draft Release, Version 1.0, of the
IEEE 802.11n specification. An Adapter with 11a/b, 11a/b/g or 11a/b/g/n
can communicate on any of its supported formats; the actual connection
will be based on the access point to which it connects.

Connection compatibility with the wireless equipment in Draft 11n mode is
not guaranteed.

The Draft 11n function cannot be used with WEP/TKIP. Draft 11n mode can
be used only with WPA-PSK (AES) mode or no security mode.

Security

1. TOSHIBA strongly recommends that you enable the WPA encryption
function otherwise your computer could be left open to illicit access via
the wireless LAN connection which may result in an intrusion that can
lead to the theft or loss of stored data among other things. In addition,
the owner of an Internet connection is responsible for all browsing,
downloading, and uploading activities on that connection. Therefore, an
unsecured wireless network connected directly to the Internet is an
open invitation for outsiders to abuse your ISP account and privileges.

2. TOSHIBA is not liable for the eavesdropping on your data due to the
use of the wireless LAN connection and any damage that may occur
thereof.

Operating Basics

Bluetooth wireless technology

Bluetooth™ wireless technology eliminates the need for cables between
electronic devices such as desktop computers, printers and mobile phones.

Bluetooth wireless technology has the following features:

Worldwide operation

The Bluetooth radio transmitter and receiver operate in the 2.4 GHz band,
which is license-free and compatible with radio systems in most countries
in the world.

Radio links

You can easily establish links between two or more devices. The link is
maintained even if the devices are not within line of sight.

User’s Manual 4-18

Security

Two advanced security mechanisms ensure a high level of security:

■ Authentication prevents access to critical data and makes it impossible

to falsify the origin of a message.

■ Encryption prevents eavesdropping and maintains link privacy.

Bluetooth™ Stack for Windows® by TOSHIBA

Please note that this software is specifically designed for the following
operating systems:

■ Microsoft

Detailed information regarding the use with these operating systems is
listed below. Please refer also to the electronic information which is
included with each software.

This Bluetooth™ Stack is based on Bluetooth™ Version 1.1/1.2/2.0+EDR
specification. TOSHIBA cannot confirm compatibility between any PC
products and/or other electronic devices that use Bluetooth™ other than
TOSHIBA mobile PCs.

®

Windows Vista™

Operating Basics

Release Notes related to the Bluetooth™ Stack for
Windows

1. Fax application software:
Regarding FAX application software, there are some software that you

cannot use on this Bluetooth™ Stack.

2. Multi User:
On Windows Vista, the use of Bluetooth is not supported in a multi-user

environment. This means that, when you use Bluetooth, other users
logged onto the same computer will not be able to use its Bluetooth
functionality.

®

by TOSHIBA

Product Support:

The latest information regarding Operating System support, Language
Support or available upgrades can be found on our web site

http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or
http://www.pcsupport.toshiba.com in the United States.

Wireless communication switch

You can enable or disable the Wireless devices function with the on/off
switch. No transmissions are sent or received when the switch is off. Slide
the switch forward to turn it on and backward to turn it off.

Turn the switch off in airplanes and hospitals. Check the LED, it stops
glowing when the wireless communication function is off.

User’s Manual 4-19

Wireless communication LED

Eject button

The LED indicates the status of the wireless communication functions.

LED status Indication
LED off Wireless communication switch is set to off.
LED glows Wireless communication switch is on.

Using optical disc drives

The illustrations in this section might differ slightly from your drive, but
operation is the same for all optical disc drives. The full-size drive provides
high-performance execution of disc-based programs. You can run either
12 cm (4.72") or 8 cm (3.15") discs without an adapter. An ATAPI interface
controller is used for disc drive operation. When the computer is accessing
a disc, an indicator on the drive illuminates.

Use the DVD Video Player to view DVD-Video discs.

If you have a CD-RW/DVD-ROM drive, refer also to the Writing CDs on
CD-RW/DVD-ROM drive section for precautions on writing to CDs.

If you have a DVD Super Multi drive supporting ±R Double Layer, refer also
to the Writing CD/DVDs on DVD Super Multi drive supporting ±R Double
Layer section for precautions on writing to CDs.

Operating Basics

Loading optical disc media

To load a disc, follow the steps below.

1. Turn on the power.

2. a. Press the eject button to open the drawer slightly.

Pressing the eject button

b. Pressing the eject button will not open the drawer when the

computer's power is off. If the power is off, you can open the drawer
by inserting a slender object (about 15 mm) such as a straightened
paper clip into the eject hole just to the right of the eject button.

User’s Manual 4-20

Manual release with the eject hole

3. Grasp the drawer gently and pull until it is fully open.

Pulling the drawer open

4. Lay the disc, label side up, in the drawer.

Operating Basics

Inserting a disc

Be careful not to touch the lens or the area around it. Doing so could cause
the drive to malfunction.

5. Press gently at the centre of the disc until you feel it click into place. The
disc should lie below the top of the spindle, flush with its base.

6. Push the centre of the drawer to close it. Press gently until it locks in
place.

User’s Manual 4-21

If the disc is not seated properly when the drawer is closed, it might be
damaged. Also, the drawer might not open fully when you press the eject
button.

Closing the drive drawer

Removing optical disc media

To remove the disc, follow the steps below.

Do not press the eject button while the computer is accessing the disc
drive. Wait for the optical disc indicator to go out before you open the
drawer. Also, if the disc is spinning when you open it, wait for it to stop
before you remove it.

Operating Basics

1. To pop the drawer partially open, press the eject button. Gently pull the
drawer out until it is fully opened.

■ When the drawer pops open slightly, wait a moment to make sure the

disc has stopped spinning before pulling the drawer fully open.

■ Turn off the power before you use the eject hole. If the disc is spinning

when you open the drawer, it could fly off the spindle and cause injury.

2. The disc extends slightly over the sides of the drawer so you can grasp
it. Hold it gently and lift it out.

Removing a disc

User’s Manual 4-22

3. Push the centre of the drawer to close it. Press gently until it locks into
place.

Buttons

The Internet button and the CD/DVD button can be assigned functions and
applications in the TOSHIBA Controls Properties.

1. Move mouse cursor and reach the top of desktop screen. The back
cards and white cards appear. Click "Button support" white card.

2. "Button Support" white card fully appears. After double click this card,
the dialog for changing button function is displayed.

3. Change function of Buttons.
Or you can go to 1. Start/All programs/TOSHIBA/Utilities and select
Toshiba Assist. 2. Choose optimize from left panel then select
TOSHIBA Button Controls.

TOSHIBA Button Support

Operating Basics

CD/DVD play control buttons

In addition to the power button, the following four buttons control functions
relating to the playback of optical media and digital audio data:

Play/Pause Starts or pauses play
Stop Stops play
Next Advances to the next track, chapter or data
Previous Returns to the previous track, chapter or data

If Random or Shuffle is selected in Windows Media Player, selecting Next
or Previous advances to a random selection.

User’s Manual 4-23

Writing CDs on a CD-RW/DVD-ROM drive

You can use the CD-RW/DVD-ROM drive to write data to CD-R/RW discs.
The following applications for writing are preinstalled:
TOSHIBA Disc Creator/Direct Disc Writer.

Important message

Before you write or rewrite to CD-R/RW media, read and follow all setup
and operating instructions in this section. If you fail to do so, the
CD-RW/DVD-ROM drive may not function properly, and you may fail to
write or rewrite, lose data or incur other damage.

Disclaimer

TOSHIBA does not bear responsibility for the following:

■ Damage to any CD-R/-RW disc that may be caused by writing or

rewriting with this product.

■ Any change or loss of the recorded contents of CD-R/-RW media that

may be caused by writing or rewriting with this product, or for any
business profit loss or business interruption that may be caused by the
change or loss of the recorded contents.

■ Damage that may be caused by using third party equipment or

software.

Given the technological limitations of current optical disc writing drives, you
may experience unexpected writing or rewriting errors due to disc quality or
problems with hardware devices. Also, it is a good idea to make two or
more copies of important data, in case of undesired change or loss of the
recorded contents.

Operating Basics

CD-R discs can be written only once. CD-RW discs can be rewritten many
times.

Before writing or rewriting

Please observe the following points when you write or rewrite the data.

■ We recommend the following manufacturers of CD-R and CD-RW

media. Media quality can affect write or rewrite success rates.

CD-R: TAIYOYUDEN CO., LTD.

MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.

CD-RW: MITSUBISHI CHEMICAL CORPORATION

RICOH Co., Ltd.

TOSHIBA has confirmed the operation of CD-R and CD-RW media of the
manufacturers above. Operation of other media cannot be guaranteed.

User’s Manual 4-24

■ CD-RW can generally be rewritten about 1,000 times. However, the

actual number of rewrites is affected by the quality of the media and the
way it is used.

■ Be sure to connect the universal AC adapter when you write or rewrite.

■ Be sure to close all other software programs except the writing

software.

■ Do not run software such as a screen saver which can put a heavy load

on the CPU.

■ Operate the computer at full power. Do not use power-saving features.

■ Do not write while virus check software is running. Wait for it to finish,

then disable virus detection programs including any software that
checks files automatically in the background.

■ Do not use hard disk utilities, including those intended to enhance hard

disk access speeds, as they may cause unstable operation and
damage data.

■ Write from the computer's hard disk drive to the CD. Do not try to write

from shared devices such as a LAN server or any other network device.

■ Writing with software other than TOSHIBA Disc Creator has not been

confirmed. Therefore, operation with other software cannot be
guaranteed.

When writing or rewriting

Please observe/consider the following when you write or rewrite to a CD-R/
RW disc.

■ Do not perform any of the following actions when writing or rewriting:

■ Change users in the Windows Vista™ operating system.

■ Operate the computer for any other function, including using a

mouse or TouchPad/Dual Mode Pad or closing/opening the LCD
panel.

■ Start a communication application such as a modem.

■ Apply impact or vibration to the computer.

■ Install, remove or connect external devices such as USB devices,

an external display, i.Link devices or optical digital devices.

■ Use the audio/video control button to reproduce music or voice.

■ Open the drive.

■ Do not use shut down/log off and Sleep/Hibernation while writing or

rewriting

■ Make sure writing or rewriting is completed before going into

Sleep/hibernation. Writing is completed if you can open the drive tray.

■ Set the computer on a level surface and avoid places subject to

vibration such as airplanes, trains or cars. Do not use an unstable
surface such as a stand.

Operating Basics

User’s Manual 4-25

Operating Basics

■ Keep mobile phones and other wireless communication devices away

from the computer.

■ Always copy data from the hard disk drive to the CD. Do not use

cutand- paste as the original data will be lost if there is a write error.

Writing CDs/DVDs on a DVD Super Multi drive supporting double layer disc recording

You can use the DVD Super Multi drive to write data to either CD-R/RW or
DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are
preinstalled:
TOSHIBA Disc Creator/Direct Disc Writer. Ulead DVD MovieFactory
TOSHIBA, which is a product of Ulead Systems, Inc.

Important message

Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM
media, read and follow all set-up and operating instructions in this section.
If you fail to do so, the DVD Super Multi drive may not function properly,
and you may fail to write or rewrite, lose data or incur other damage.

Disclaimer

TOSHIBA does not bear responsibility for the following:

■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may

be caused by writing or rewriting with this product.

■ Any change or loss of the recorded contents of CD-R/RW or DVD-R/-

RW/ +R/+RW /-RAM media that may be caused by writing or rewriting
with this product, or for any business profit loss or business interruption
that may be caused by the change or loss of the recorded contents.

■ Damage that may be caused by using third party equipment or

software.

Given the technological limitations of current optical disc writing drives, you
may experience unexpected writing or rewriting errors due to disc quality or
problems with hardware devices. Also, it is a good idea to make two or
more copies of important data, in case of undesired change or loss of the
recorded contents.

®

for

Before writing or rewriting

Please observe the following points when you write or rewrite data.

■ Based on TOSHIBA's limited compatibility testing, we suggest the

following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM
media. However, in no event does TOSHIBA guarantee the operation,
quality or performance of any disc. Disc quality can affect write or
rewrite success rates.

User’s Manual 4-26

Operating Basics

CD-R: TAIYOYUDEN CO., LTD.

MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.

CD-RW: MITSUBISHI CHEMICAL CORPORATION

RICOH Co., Ltd.

DVD-R: DVD Specifications for Recordable Disc for General

Version 2.0
TAIYOYUDEN CO., LTD.
Matsushita Electric Industrial Co., Ltd.

DVD-RW: DVD Specifications for Re-recordable Disc for

Version 1.1 or Version 1.2
VICTOR COMPANY OF JAPAN, LIMITED
MITSUBISHI CHEMICAL CORPORATION

DVD+R: MITSUBISHI CHEMICAL CORPORATION

RICOH Co., Ltd.

DVD+RW: MITSUBISHI CHEMICAL CORPORATION

RICOH Co., Ltd.

*DVD-RAM DVD Specifications for DVD-RAM Disc for Version

2.0, Version 2.1 or Version 2.2
Matsushita Electric Industrial Co., Ltd.
Hitachi Maxell Ltd.
*DVD Multi drive and DVD Super Multi can use

DVD-RAM.

DVD+R

MITSUBISHI CHEMICAL CORPORATION

(Double Layer)

DVD-R

MITSUBISHI CHEMICAL COPRORATION

(Dual Layer)

DVD-R Label

FUJIFILM Corporation

Flash

DVD+R Label

FUJIFILM Corporation

Flash

■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors

may occur. Be careful to check the disc for dirt or damage before you
use it.

■ The actual number of rewrites to CD-RW or DVD-RW/+RW/-RAM is

affected by the quality of the disc and the way it is used.

■ There are two types of DVD-R: authoring and general use discs. Do not

use authoring discs. Only general use discs can be written to by a
computer drive.

User’s Manual 4-27

Operating Basics

■ We can support only Format 1 of DVD-R DL. Therefore you can not do

the additional writing. If your data is under DVD-R (SL) capacity, we
suggest to use DVD-R (SL) media.

■ You can use DVD-RAM discs that can be removed from a cartridge and

DVD-RAM discs designed without a cartridge. You cannot use a disc
with a 2.6 GB single-sided capacity or 5.2 GB double-sided capacity.

■ Other DVD-ROM drives for computers or other DVD players may not be

able to read DVD-R/+R/-RW/+RW/-RAM discs.

■ Data written to a CD-R/DVD-R/+R disc cannot be deleted either in

whole or in part.

■ Data deleted (erased) from a CD-RW and DVD-RW/+RW/-RAM disc

cannot be recovered. Check the content of the disc carefully before you
delete it. If multiple drives that can write data to discs are connected, be
careful not to delete data from the wrong drive.

■ In writing to a DVD-R/+R/-RW/+RW disc, some disc space is required

for file management, so you may not be able to write the full capacity of
the disc.

■ Since the disc is based on the DVD-R/-RW standard, it will be filled with

dummy data if the written data is less than about 1 GB. Even if you write
only a small amount of data, it might take time to fill in the dummy data.

■ Two types of DVD-R/+R/-RW/+RW/-RAM discs are on the market: data

and video. Use a video disc to store video data. You can use video
discs on a DVD recorder as well as on your computer's DVD-ROM
drive. You cannot use data discs on a DVD recorder.

■ DVD-RAM formatted by FAT32 cannot be read in Windows 2000

without DVD-RAM Driver Software.

■ When multiple drives that can write data to discs are connected, be

careful not to write to the wrong drive.

■ Be sure to connect the universal AC adapter before you write or rewrite.

■ Before you enter Sleep/Hibernation Mode, be sure to finish DVD-RAM

writing. Writing is finished if you can eject DVD-RAM media.

■ Be sure to close all other software programs except the writing

software.

■ Do not run software such as a screen saver, which can put a heavy load

on the CPU.

■ Operate the computer at full power. Do not use power-saving features.

■ Do not write while virus check software is running. Wait for it to finish,

then disable virus detection programs including any software that
checks files automatically in the background.

■ Do not use hard disk utilities, including those intended to enhance hard

disk access speed, as they may cause unstable operation and damage
data.

■ Write from the computer's hard disk drive to the CD. Do not try to write

from shared devices such as a LAN server or any other network device.

User’s Manual 4-28

Operating Basics

■ Writing with software other than TOSHIBA Disc Creator or Ulead DVD

MovieFactory
operation with other software cannot be guaranteed.

®

for TOSHIBA has not been confirmed. Therefore,

When writing or rewriting

Please observe/consider the following when you write or rewrite to a
CD-R/RW, DVD-R/-RW/-RAM or DVD+R/+RW disc.

■ Do not perform any of the following actions when writing or rewriting:

■ Change users in the Windows Vista™ operating system.

■ Operate the computer for any other function, including using a

mouse or TouchPad/Dual Mode Pad or closing/opening the LCD
panel.

■ Start a communication application such as a modem.

■ Apply impact or vibration to the computer.

■ Install, remove or connect external devices such as USB devices,

an external display, i.Link devices or optical digital devices.

■ Use the audio/video control button to reproduce music or voice.

■ Open the drive.

■ Do not use shut down/log off and Sleep/Hibernation while writing or

rewriting.

■ Make sure writing or rewriting is completed before going into

Sleep/hibernation. Writing is completed if you can open the drive tray.

■ Set the computer on a level surface and avoid places subject to

vibration such as airplanes, trains or cars. Do not use an unstable
surface such as a stand.

■ Keep mobile phones and other wireless communication devices away

from the computer.

■ Always copy data from the hard disk drive to the CD. Do not use cut-

and-paste as the original data will be lost if there is a write error.

How to make a Label Flash DVD

Simplified steps for making a Label Flash DVD:

1. Insert a Label Flash disc in DVD drive.

Set printable surface for underside.

2. Click Start  All Programs  DVD MovieFactory for TOSHIBA 
Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD

MovieFactory.

3. Click Print Disc Label  Label Printing. Ulead Label@Onece is
started.

4. Click the General tab.

5. Choose DVD Drive for Printer. e.g. <E:> PIONEER DVD....

6. Add and customize the look of your images and text.

User’s Manual 4-29

Operating Basics

7. Click Label Flash setting and choose Draw Quality.

8. Click Print.

The availability of Label Flash function depends on the model you
purchased.

When Using Ulead DVD MovieFactory® for TOSHIBA

How to make a DVD-Video

Simplified steps for making a DVD-Video from video data captured from a
DV-Camcorder:

1. Click Start  All Programs  DVD MovieFactory for TOSHIBA 
Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD
MovieFactory.

2. Insert a DVD-RW or DVD+RW disc in Burner.

3. Click Video Disc  Burn Video to Disc to launch Direct Recording
dialog box, choose DVD-Video/+VR to invoke Straight Capture to
Disc Page.

4. Choose DVD-Video format.

5. Confirm the capture source is DV.

6. Press Capture button.

Simplified steps for making a DVD-Video from adding a video source:

1. Click Start  All Programs  DVD MovieFactory for TOSHIBA 
Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD
MovieFactory.

2. Click Video Disc  New Project to invoke 2nd Launcher, choose your
project type, then invoke DVD MovieFactory.

3. Add source from HD Disk by click Add Video files button to invoke
browser dialog box.

4. Choose the sourse video then go to the Next page to apply Menu.

5. After choose the menu template, press Next button to go to Burning
Page.

6. Choose the output type then press Burn button.

How to learn more about Ulead DVD MovieFactory®

Please refer to the Help and Manul file for additional Ulead DVD
MovieFactory information.

User’s Manual 4-30

Important information for use

Note the following limitations when you write video DVD:

1. Editing digital video

■ Log in with Administrator rights to use DVD MovieFactory.

■ Make sure that your computer is running on AC power when using

DVD MovieFactory

■ Operate the computer at Full Power. Do not use power-saving features.

■ While you are editing DVD, you can display previews. However, if

another application is running, the preview might not display properly.

■ DVD MovieFactory cannot edit or play copy protected content.

■ Do not enter Sleep/Hibernation Mode while using DVD MovieFactory

■ Do not operate DVD MovieFactory immediately after turning on the

computer. Please wait until all Disc Drive activity has stopped.

■ When recording to a DV-Camcorder, to ensure you capture all of your

data, let the camcorder record for a few seconds before you begin
recording your actual data.

■ CD recorder, JPEG functions, DVD-Audio, mini DVD and Video CD

functions are not supported in this version.

■ While recording video to DVD or tape, please close all other programs.

■ Do not run software like a screen saver because it can put a heavy load

on the CPU.

■ Do not support MP3 decode and encode.

2. Before recording the video to DVD

■ When you record to DVD disc, please use only discs recommended by

the Drive manufacturer.

■ Do not set the working drive to a slow device like a USB 1.1 hard disk

drive or it will fail to write DVD.

■ Do not perform any of the following actions:

■ Operate the computer for any other function, including using a

mouse or TouchPad/Dual Mode Pad or closing/opening the LCD
panel.

■ Bump or cause vibration to the computer.

■ Use the Mode control button and Audio/Video control button to

reproduce music or voice.

■ Open the DVD drive.

■ Install, remove or connect external devices, including the following:

■ SD card, USB devices, external display, i.LINK. devices, optical

digital devices.

■ Please verify your disc after recording important data.

■ DVD-R/+R/-RW disc cannot be written in VR format.

■ Not support to output VCD or SVCD format.

Operating Basics

User’s Manual 4-31

3. About Straight to Disc

■ Not support to record on DVD-R/+R disc

■ Not support to record DVD+VR format by HDV

■ HDV support to burn DVD-Video only

■ DVD-VR format not support to add Menu

4. About recorded DVDs

■ Some DVD-ROM drives for personal computers or other DVD players

may not be able to read DVD-R/+R/-RW/-RAM discs.

■ When playing your recorded disc on your computer, please use the

DVD Video Player.

■ If you use an over-used rewritable disc, the full formatting might be

locked. Please use a brand new disc.

TOSHIBA Disc Creator

Note the following limitations when you use TOSHIBA Disc Creator:

■ DVD-Video cannot be created using TOSHIBA Disc Creator

■ DVD-Audio cannot be created using TOSHIBA Disc Creator

■ You cannot use the TOSHIBA Disc Creator "Audio CD" function to

record music to the DVD-R/-RW or DVD+R/+RW media.

■ Do not use the "Disc Backup" function of TOSHIBA Disc Creator to

copy DVD-Video and DVD-ROM with copyright protection.

■ DVD-RAM media cannot be backed up with the "Disc Backup" function

of TOSHIBA Disc Creator

■ You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or

DVD+R/+RW using the "Disc Backup" function of TOSHIBA Disc
Creator.

■ You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or

DVD+R/+RW to CD-R/RW using TOSHIBA Disc Creator

■ TOSHIBA Disc Creator cannot record in packet format.

■ You might not be able to use the "Disc Backup" function of TOSHIBA

Disc Creator to backup a DVD-R/-RW or DVD+R/+RW disc that was
made with other software on a different DVD-R/-RW or DVD+R/+RW
recorder.

■ If you add data to a DVD-R and DVD+R disc that you have already

recorded to, you might not be able to read the added data under some
circumstances. It cannot be read in 16-bit operating systems, such as
Windows 98SE and Windows ME, in Windows NT4 you will need
Service Pack 6 or later to read the data, and in Windows 2000 you will
need Service Pack 2 or later to read it. Some optical media drives
cannot read added data regardless of the operating system.

■ TOSHIBA Disc Creator does not support recording to DVD-RAM discs.

To record to a DVD-RAM, use Explorer or other similar utility.

Operating Basics

User’s Manual 4-32

■ When you back up a DVD disc, be sure the source drive supports

■ When you back up a DVD-R, DVD-RW, DVD+R or DVD+RW, be sure to

■ You cannot partially delete any data written to a CD-RW, DVD-RW or

Data Verification

To verify that data is written or rewritten correctly, follow the steps below
before you write or rewrite a Data CD/DVD.

1. Display the setting dialog box by one of the following two steps:

2. Mark the Verify written data check box.

3. Select File Open or Full Compare mode.

4. Click the OK button.

Media Care

This section provides tips on protecting data stored on your discs and
disks.

Handle your media with care. The following simple precautions will
increase the lifetime of your media and protect the data stored on it:

1. Store your discs in the container they came in to protect them and keep

2. Do not bend the disc.

3. Do not write on, apply a sticker to, or otherwise mar the surface of the

4. Hold the disc by its outside edge or the edge on the center hole.

5. Do not expose to direct sunlight, or extreme heat or cold, and do not

6. If your discs become dusty or dirty, wipe them with a clean dry cloth.

Operating Basics

recording to DVD-R/-RW or DVD+R/+RW discs. If the source drive
does not support recording to DVD-R/-RW or DVD+R/+RW discs, it
might not be backed up correctly.

use the same type of disc.

DVD+RW disc.

■ Click the setting button ( ) for writing on the main toolbar in the

Data CD/DVD mode.

■ Select Setting for writing → Data CD/DVD in the Setting menu.

them clean.

disc that contains data.

Fingerprints on the surface can prevent the drive from properly reading
data.

place heavy objects on your discs.

Wipe from the center out, do not wipe in a circular direction around the
disc. If necessary, use a cloth dampened in water or a neutral cleaner.
Do not use benzine, thinner or similar cleaner.

User’s Manual 4-33

Disks

TV Out Port

TV-Out

Operating Basics

1. Store your disks in the container they came in to protect them and keep
them clean. If a disk is dirty, do not use cleaning fluid. Clean it with a
soft damp cloth.

2. Do not slide back the disk's protective metal covering or touch the disk's
magnetic surface. Fingerprints may prevent the disk drive from reading
data from the disk.

3. Data may be lost if the disk is twisted, bent, or exposed to direct
sunlight, or extreme heat or cold.

4. Do not place heavy objects on your disks.

5. Do not eat, smoke, or use erasers near your disks. Foreign particles
inside the disk's jacket can damage the magnetic surface.

6. Magnetic energy can destroy data on disks. Keep your disks away from
speakers, radios, television sets and other sources of magnetic fields.

Use the TV-Out port to connect to a television. Be sure to use a 4 pin type
S-video cable.

Setting up more than one display

You can set up your computer to utilize more than one display, effectively
spreading a single desktop screen across two monitors.

The Display settings window allows you to adjust more precisely the
relative positioning of the two displays when they are configured as an
extended desktop. On the Display Settings window, the two displays can be
positioned horizontally, vertically or in any diagonal configuration you wish,
as shown below.

User’s Manual 4-34

Operating Basics

If an external display will not be connected next time you use your
computer, you should cancel any extended desktop or clone display
settings before shutting down your computer.

Clone display settings are those where more than one device has been
selected and is simultaneously applicable.

Cleaning the computer

To help ensure long, trouble-free operation, keep the computer free of dust
and use care with liquids around the computer.

■ Be careful not to spill liquids into the computer. If the computer does get

wet, turn the power off immediately and let the computer dry completely
before you turn it on again.

■ Clean the computer using a slightly damp (with water) cloth. You can

use glass cleaner on the display. Spray a small amount of cleaner on a
soft, clean cloth and wipe the screen gently with the cloth.

Never spray cleaner directly onto the computer or let liquid run into any
part of it. Never use harsh or caustic chemical products to clean the
computer.

User’s Manual 4-35

Moving the computer

The computer is designed for rugged durability. However, a few simple
precautions taken when moving the computer will help ensure trouble-free
operation.

■ Make sure all disk activity has ended before moving the computer.

Check the Built-in Hard Disk Drive and optical disc drive indicators
on the computer.

■ If a disk is in the disk drive, remove it.

■ If a disc is in the optical disc drive, remove it. Also make sure the optical

disc drive drawer is securely closed.

■ Turn off the power to the computer.

■ Disconnect all peripherals before moving the computer.

■ Close the display. Do not pick up the computer by its display panel or

back (where the interface ports are located).

■ Close all port covers.

■ Disconnect the AC adapter if it is connected.

■ Use the carrying case when transporting the computer.

Operating Basics

User’s Manual 4-36

The Keyboard

The computer's keyboard layouts are compatible with a 104/105-key
enhanced keyboard. By pressing some keys in combination, all the
104/105-key keyboard functions can be executed on the computer.

The number of keys on your keyboard depends on which country/region's
keyboard layout your computer is configured with. Keyboards for numerous
languages are available.

There are five types of keys: typewriter keys, keypad overlay, function keys,
soft keys and cursor control keys.

Typewriter keys

The typewriter keys, produce the upper- and lower-case letters, numbers,
punctuation marks, and special symbols that appear on the screen.

There are some differences, however, between using a typewriter and
using a computer keyboard:

■ Letters and numbers produced in computer text vary in width. Spaces,

which are created by a space character may also vary depending on
line justification and other factors.

■ The lowercase l (el) and the number 1 (one) are not interchangeable on

computers as they are on a typewriter.

■ The uppercase O (oh) and the 0 (zero) are not interchangeable.

■ The Caps Lock function key locks only the alphabetic characters in

uppercase while the shift lock on a typewriter places all keys in the
shifted position.

■ The Shift keys, the Tab key, and the BkSp (backspace) key perform the

same function as their typewriter counterparts but also have special
computer functions.

The Keyboard

Chapter 5

User’s Manual 5-1

F1 ... F12 function keys

The function keys, not to be confused with Fn, are the 12 keys at the top of
your keyboard. These keys are dark gray, but function differently from the
other dark gray keys.

F1 through F12 are called function keys because they execute programmed
functions when pressed. Used in combination with the Fn key, keys marked
with icons execute specific functions on the computer. See the section, Soft
keys: Fn key combinations, in this chapter. The function executed by
individual keys depends on the software you are using.

Soft keys: Fn key combinations

The Fn (function) is unique to TOSHIBA computers and is used in
combination with other keys to form soft keys. Soft keys are key
combinations that enable, disable or configure specific features.

Some software may disable or interfere with soft-key operations. Soft-key
settings are not restored by the Sleep feature.

Emulation keys

Your software may require you to use keys that the keyboard does not
have. Pressing the Fn key and one of the following keys simulates the
enhanced keyboard's functions.

The Keyboard

Press Fn + Enter to simulate Enter on the enhanced keyboard's numeric
keypad.

Press Fn + Ctrl to simulate the enhanced keyboard's right Ctrl key.

User’s Manual 5-2

Hotkeys

The Keyboard

Fn + ESC Volume Mute – Turns the volume on and off.
Fn + F1 Instant Security – Enters screen saver mode and

Fn + F2 Power Save Modes – Displays the power save

Fn + F3 Sleep – This hot key switches the system to

Fn + F4 Hibernate – This hot key switches the system to

Fn + F5 Display Selection – Changes displays.

Default resolution for simultaneous mode is set to WXGA+ (1440 × 900). If
you connect an RGB (Monitor) that is not WXGA+, change it in "Control
Panel/Personalization/Display settings".

Fn + F6 Brightness Down
Fn + F7 Brightness Up
Fn + F8 Wireless Device Controls – Pressing this hot

Fn + F9 TouchPad/Dual Mode Pad On/Off
Fn + Space Change Resolution – Cycles sequentially from

Fn + 1Zoom Out – To reduce the icon size on the

Fn + 2

blanks the screen. To restore your desktop, press
any key or use the TouchPad/Dual Mode Pad.

modes and lets you change the power settings

Sleep mode.

Hibernate mode.

key allows you to switch between active wireless
devices if the wireless communication switch is
switched on.

the current resolution to 800 × 600 to 1024 × 768
and back again to the original resolution.

desktop or the application window, press the 1 key
while holding down the Fn key.

Zoom In – To enlarge the icon size on the desktop
or the application window, press the 2 key while
holding down the Fn key.

Before using Fn + 1 and Fn + 2, you must install the TOSHIBA Zooming
Utility. Please be aware that this 'zooming' function is only available within
Microsoft Internet Explorer, Microsoft Office, Windows Media Player and
Adobe Reader, and for the icons on the desktop.

User’s Manual 5-3

Windows special keys

The keyboard provides two keys that have special functions in Windows
Vista. One activates the Start menu and the other has the same function as
the secondary mouse button.

This key activates the Windows Vista Start menu

This key has the same function as the Right mouse button.

Number Pad

The number pad is activated by pressing the Num Lock key, the LED will
appear when active. Use the keypad to type numbers and generate ASCII
charcters.

Generating ASCII characters

Not all ASCII characters can be generated using normal keyboard
operation. But, you can generate these characters using their ASCII codes.

With the Num lock on:

1. Hold down Alt.

2. Using the number pad keys, type the ASCII code.

3. Release Alt, and the ASCII character appears on the display screen.

With the Num Lock off:

1. Hold Alt + Fn.

2. Using the number pad keys, type the ASCII code.

3. Release Alt + Fn, and the ASCII character appears on the display
screen.

The Keyboard

User’s Manual 5-4

Power and Power-Up Modes

Chapter 6

Power and Power-Up Modes

The computer's power resources include the AC adapter and internal
batteries. This chapter gives details on making the most effective use of
these resources including charging and changing batteries, tips for saving
battery power, and power up modes.

Power conditions

The computer's operating capability and battery charge status are affected
by the power conditions: whether an AC adapter is connected, whether a
battery is installed and what the charge level is for the battery.

Power on Power off (no operation)

AC adapter
connected

Battery fully
charged

Battery partially
charged

No battery
installed or no
charge

• Operates

• No charge

• LED: Battery blue
DC IN blue

• Operates

• Charge

• LED: Battery Amber
DC IN blue

• Operates

• No charge

• LED: Battery off
DC IN blue

• No charge

• LED: Battery blue

• Charge

• LED: Battery Amber

• No charge

• LED: Battery off

DC IN blue

DC IN blue

DC IN blue

User’s Manual 6-1